Bonded dimethylacrylamide as a permanent coating for capillary electrophoresis

Stepwise elusion method in micellar electrokinetic chromatography via sequential use of lithium perfluorooctadecyl sulfonate and lithium dodecyl sulfate

An effective stepwise micellar electrokinetic chromatography (MEKC) elution method was developed using lithium perfluorooctadecyl sulfonate (LPFOS) and lithium dodecyl sulfate (LDS). The hydrogen-bonding property of LPFOS micelles differs from that of LDS micelles, which leads to remarkably different selectivity in the transfer of solutes to the micelles. The present stepwise method is performed by replacing the inlet reservoir of a first running solution containing LPFOS with that of a second running solution containing LDS during a single separation run in the absence of electroosmotic flow under acidic conditions, where LPFOS micelles work as carriers in first and then LDS micelles turn over. Effective separation of 15 nonionic aromatic compounds was controlled well by adjusting the time in the inlet reservoir, which could not be accomplished with systems using only LPFOS or only LDS, with significant changes in the elution order where necessary. Furthermore, separations with the present stepwise method were easily simulated, and the replacement time was optimized for 3.1min from a 70.0mM LPFOS solution to a 67.5mM LDS solution with nearly complete separation within 15min using the simulated parameters.

Micellar electrokinetic chromatography of aromatic anions and non-ionic aromatic compounds with stepwise changes of the concentration of cetyltrimethylammonium chloride

Micellar electrokinetic chromatography in which the concentration of cetyltrimetylammmonium chloride (CTAC) was sequentially changed in the separation system was investigated using 10 aromatic anions and 11 non-ionic aromatic compounds as model analytes. All separations were performed in the absence of electroosmotic flow (EOF), and thus, analytes were detected in the order of their strength of interaction with micelles in the system. In isocratic elutions without EOF, the model analytes could be separated better with lower concentrations of CTAC but migration times of the analytes possessing relatively higher polarities increased markedly, and thus, long analysis times were required. Therefore, we attempted to increase the concentration of CTAC during a single measurement to reduce the analysis time without hindering the resultant separation of analytes obtained with lower concentrations. Briefly, the present surfactant stepwise elution can be performed by a sequential increase in CTAC concentrations of the running solution in the anodic reservoir from 30 to 50mM for the anions and from 20 to 50 mM for the non-ionic compounds. Additionally, to perform expected gradient separations with good reproducibility, each running solution with a different CTAC concentration was treated with tetraethylammmonium chloride as an additive to adjust electric conductivities of each running solution to be equal. Under this condition, CTAC micelles of each zone of different CTAC concentrations would migrate with practically the same velocity. Consequently, by the present stepwise method, both the 10 anionic analytes and the 11 non-ionic analytes were well separated within reasonable periods which corresponded approximately to two-third and less than half of those by the isocratic elutions, respectively.

Characterization of CdSe quantum dots with bidentate ligands by capillary electrophoresis

The CdSe quantum dots (QDs) with bidentate ligands: a-diimine (NN) and dihydrolipoic acid (DHLA) were synthesized and characterized by UV-Vis, particle size and capillary electrophoretic techniques. Two systems were analyzed: CdSe with one ligand (CdSe/ligand) and CdSe with two different ligands (CdSe//ligand1/ligand2), where ligand = α-diimine or DHLA. Hydrodynamic features of functionalized QDs were characterized by zone capillary electrophoretic (CZE), and particle size techniques and these methods were consistent. It was established that CZE, micellar (MEKC) and microemulsion (MEEKC) modes were suitable for separating charged CdSe QDs and that no peaks were obtained for QDs passivated with electrically neutral ligands. For CdSe QDs with neutral (NN) ligands, a preconcentration method with the use of a micellar plug was introduced for visualizing these QDs. A sharp peak representing neutral QDs was obtained within the zone of micellar plug of a non-ionic surfactant, Here, a ligand character used for CdSe modification and the type of the electrophoretic method applied were the determining factors for the QDs peak visualization. Moreover, examples of visualization of charged and neutral QDs on the same run were presented, and for this purpose, dual mechanism (separation/preconcentration) was proposed.

Quantitative evaluation of lectin-reactive glycoforms of α(1)-acid glycoprotein using lectin affinity capillary electrophoresis with fluorescence detection

α(1)-Acid glycoprotein (AGP) was previously shown to be a marker candidate of disease progression and prognosis of patients with malignancies by analysis of its glycoforms via lectins. Herein, affinity capillary electrophoresis of fluorescein-labeled AGP using lectins with the aid of laser-induced fluorescence detection was developed for quantitative evaluation of the fractional ratios of concanavalin A-reactive or Aleuria aurantia lectin-reactive AGP. Labeled AGP was applied at the anodic end of a fused-silica capillary (50 μm id, 360 μm od, 27 cm long) coated with linear polyacryloyl-β-alanyl-β-alanine, and electrophoresis was carried out for about 10 min in 60 mM 3-morpholinopropane-1-sulfonic acid-NaOH buffer (pH 7.35). Addition of the lectins to the anode buffer resulted in the separation of lectin-reactive glycoform peaks from lectin-non-reactive glycoform peaks. Quantification of the peak area of each group revealed that the percent of lectin-reactive AGP is independent of a labeling ratio ranging from 0.4 to 1.5 mol fluorescein/mol AGP, i.e. the standard deviation of 0.5% for an average of 59.9% (n=3). In combination with a facile procedure for micro-purification of AGP from serum, the present procedure, marking the reactivity of AGP with lectins, should be useful in determining the prognosis for a large number of patients with malignancies.

Neutral coatings for the study of polycation/multicharged anion interactions by capillary electrophoresis: application to dendrigraft poly-L-lysines with negatively multicharged molecules

The study of interactions between oppositely multicharged (macro)molecules remains a challenging issue. In frontal analysis capillary electrophoresis (FACE), it is difficult to avoid the adsorption of one of the interacting partners onto the capillary wall. In this work, we demonstrate the possibility to use FACE and affinity capillary electrophoresis (ACE) on a neutrally coated capillary for the study of interactions between a polycationic dendrigraft (or linear) poly-l-lysines, on one hand, and a multicharged anionic biomolecule (adenosine monophosphate, AMP, or adenosine triphosphate, ATP), on the other hand. A systematic comparison of four different neutral coatings (hydroxypropyl cellulose, polydimethylacrylamide, polyacrylamide, polyethylene glycol) has been performed based on the repeatability of the electrophoretic migration of the dendrigraft poly-l-lysines at pH close to neutrality. Both FACE and ACE methodogies were then used to study the interactions and to get the association constants and the stoichiometry of the complex. Multisite interactions, with two classes of independent sites, were determined. The specificity of the dendritic polylysine structure compared with linear polylysine in the interaction with ATP or AMP is also emphasized.

Two-step perpendicular free-solution isoelectric focusing in a microchamber array chip

A free-solution microfluidic chip device was fabricated for small-scale protein fractionation based on the principle of two-step perpendicular isoelectric focusing (IEF) previously reported in a gel slab. The microchip was composed of two separate glass plates with a square array of 100 indentations etched on the facing side of each plate. By changing the relative position of the two plates, ten channels can be formed as ranges of the staggered indentations and can be switched to the perpendicular direction, or 100 chambers of 140 nL each can be produced by perfect overlapping of the indentations. The entire pH range of the carrier ampholyte was fractionated into 10 successive pH segments in the first IEF, and each of the segments was further fractionated into 10 fractions by the second IEF at a right angle to the first one. This chip enabled IEF fractionation at a lower voltage and in a shorter time, compared with a linear apparatus operated in one direction. Fluorescence-labeled peptides with a small isoelectric point (pI) difference (DeltapI = 0.3) were recovered in different chambers in a total separation time of 10 min at a maximum applied voltage of 500 V.

Spermine-graft-dextran non-covalent copolymer as coating material in separation of basic proteins and neurotransmitters by capillary electrophoresis

Spermine-graft-dextran (Spe-g-Dex) copolymer was synthesized and used as a non-covalent coating for the separation of proteins and neurotransmitters by capillary electrophoresis. The coating was obtained via flushing the capillary with 1.0% Spe-g-Dex copolymer solution for 2min. Electroosmotic flow (EOF) was strongly suppressed, ranging from -1.60x10(-9) to 3.65x10(-9)m(2)V(-1)s(-1). Effect of experimental conditions, such as the copolymer concentration, the concentration and pH of the background electrolyte (BGE), on the Spe-g-Dex coating was investigated. Separation of lysozyme, cytochrome c, ribonuclease A and alpha-chymotrypsinogen yielded high separation efficiencies ranging from 141000 to 303000plates/m and recoveries from 85.4% to 98.3% at pH 4.0 (284.0mM sodium acetate-acetic acid buffer, I=50mM). Run-to-run repeatabilities and day-to-day, and capillary-to-capillary reproducibilities were all below 1.7%. In addition, Spe-g-Dex coating allowed the successful separation of five neurotransmitters, 5-hydroxytryptamine, dopamine, epinephrine, isoprenaline, dobuamine at pH 4.0 with high separation efficiencies of 290000-449000plates/m.

On-chip connector valve for immunoaffinity chromatography in a microfluidic chip

A miniature valve that operates between a chip port and a tube fitting was developed. The valve functions by means of a rotor, 3 mm in diameter and 1.5 mm in height, made of Teflon, with a 0.2-mm diameter hole at its center that is co-axial with the tube fitting. It also has a radial groove, 0.85 mm long, 0.2 mm wide, and 0.2 mm deep, at the bottom surface, starting at its center. The chip port and the tube fitting have an offset of 0.75 mm, and, thus, the rotation of the rotor can make an on and off connection between the chip port and the groove, which is connected to the tubing. The valve had a pressure resistance of at least 1.0 MPa. The on-chip valve can be placed in position by adding only a single part, a valve rotor, and no changes in the fabrication of the glass microchip are required. Since the valve functions as a part of a connector, we refer to it as an on-chip connector valve. Immunoaffinity chromatography of a fluorescence-labeled recombinant antibody fragment was carried out in a glass microchip using the valves.

Poly(N,N-dimethylacrylamide)-grafted polyacrylamide: a self-coating copolymer for sieving separation of native proteins by CE

The potential of a series of newly synthesized poly(N,N-dimethylacrylamide) (PDMA) grafted polyacrylamide (PAM) copolymers (P(AM-PDMA)) as a replaceable separation medium for protein analysis was studied. A comparative study with and without copolymers was performed; the separation efficiency, analysis reproducibility and protein recovery proved that the P(AM-PDMA) copolymers were efficient in suppressing the adsorption of basic proteins onto the silica capillary wall. Furthermore, the size-dependent retardation of native proteins in a representative P(AM-PDMA) copolymer was demonstrated by Ferguson analysis. The results showed that the P(AM-PDMA) copolymers combine the good coating property of PDMA and the sieving property of PAM and could be applied as a sieving matrix for the analysis of native proteins.

Effect of barium tetraborate on the separation of tryptic digests of proteins by zone electrophoresis in uncoated capillaries

A simple, fast, efficient and reproducible method for peptide separations in CZE is reported. It consists in running tryptic digests of peptides in an uncoated capillary, in a BGE composed of tetraborate as a buffering ion, in which the typical sodium counterion is substituted with barium. Efficient absorption of this divalent cation to ionized silanols and barium silicate precipitation seem to be able to shield effectively the silica surface from separands. This is demonstrated by the fact that, when tBa(2+) ions are present in solution (from pH 8.5 up to pH 11.0), the electroendoosmotic flow is reversed; such reversal being progressively higher at higher pH values, by up to a four-fold. Separations become progressively better at higher pH values, whereas at pH 11 in sodium tetraborate they are dramatically worsened. It is further hypothesized that the barium silicate layer further protects the silica surface against dissolution and corrosion which is quite substantial at pH 11.

Flow splitting at the inlet electrode as a method for decreasing the electric current in electric field assisted liquid chromatography

The combination of pressurized flow and electric field offers, with the use of capillary columns, several options for retention control. However, it has been shown that the utility of this technique is strongly limited by the high electric current that is generated at the high electric field strengths that are needed. We have earlier shown that the high current is a result of locally increased mobile phase ion concentration in the electric field, particularly around the inlet electrode. In this paper, we report that by splitting the mobile phase flow around the inlet electrode a relatively constant ion concentration around the electrode can be obtained and the high currents are there by reduced.

Cationic lipid vesicles as coating precursors in capillary electrochromatography: Separation of basic proteins and neutral steroids

1,2-Dioleyl-3-trymethylammoniumpropane (DOTAP) lipid vesicles were employed as coating precursors to obtain a semipermanent cationic lipid bilayer in silica capillary. The coating procedure was relatively fast and simple. Reliable results for the separation of four basic proteins (alpha-chymotrypsinogen A, ribonuclease A, cytochrome C, lysozyme) were obtained by using an acetate buffer under acidic conditions. The RSDs of the migration times were not higher than 0.5% run-to-run and about 1% day-to-day (3 days), while the RSDs of the peak areas were within 7% day-to-day (3 days). The day-to-day RSD of the EOF mobility of about 1%, confirmed that the DOTAP coating was stable for the separation of basic proteins, under acidic buffers. In addition to basic proteins the DOTAP coating was found suitable under acidic conditions for the repeatable separation of neutral steroids. The potential of DOTAP as a carrier in background electrolyte solution was studied.

Characterization of anacardic acids by micellar electrokinetic chromatography and mass spectrometry

A possibility of using capillary electrophoresis for separation of anacardic acids (6-alkylsalicylic acids) has been studied. Conventional micellar electrokinetic chromatography (MEKC) in non-coated fused silica capillaries and reversed-flow micellar electrokinetic chromatography (RF-MEKC) in capillaries coated with polydimethylacrylamide was applied for separation of anacardic acids extracted from cashew nuts. Influence of the composition of background electrolyte on the resolution of anacardic acid isomers was evaluated. Separations were performed using sodium dodecyl sulphate (SDS) micelles and mixed micelles of SDS and polyoxyethylene lauryl ether as a pseudostationary phase. To further improve the separation in RF-MEKC, beta-cyclodextrin and a dual cyclodextrin system of beta-cyclodextrin with heptakis-6-sulphato-beta-cyclodextrin was added to the working electrolyte. Best separation of anacardic acids were achieved in the polydimethylacrylamide-coated capillary using 10 mM phosphate background electrolyte pH 6.5 with addition of 1 M urea, 20% acetonitrile, 10 mM of beta-cyclodextrin and 1 mM of heptakis-6-sulfo-beta-cyclodextrin. Mass spectrometry was used for the identification of anacardic acids in the extract from cashew nuts in single and tandem mode using Q-TOF instrument. Nine anacardic acids were identified in the extract form the cashew nuts.

Suppression of electroosmotic flow and its application to determination of electrophoretic mobilities in a poly(vinylpyrrolidone)-coated capillary

A hydrophilic polymer, poly(vinylpyrrolidone) (PVP), was employed for suppressing the electroosmotic flow (EOF). A capillary was filled with aqueous PVP solution for coating the capillary wall with PVP; the PVP solution was then replaced by a migration buffer solution containing no PVP. Three types of PVP with different molecular weights were examined. The EOF was suppressed more effectively as the molecular weight of PVP increased. The EOF in the coated capillary was approximately 10-fold smaller than that of a bare capillary and was constant in the pH range of 6-8. The suppressed EOF was stable even when no PVP was added to the migration buffer. However, the EOF increased significantly when sodium dodecyl sulfate was added into the migration buffer. The method was applied for determining the electrophoretic mobilities of inorganic anions that have negative electrophoretic mobilities larger than the electroosmotic mobility of the bare capillary. A novel method for determining the electrophoretic mobilities was proposed based on the linear relationship between electric current and electrophoretic mobility. The electrophoretic mobility was proportional to the electric current. Therefore, the intercept of the regression equation represents the electrophoretic mobility at room temperature. The electrophoretic mobilities were in good agreement with the absolute electrophoretic mobilities.

Utilizing the pH hysteresis effect for versatile and simple electrophoretic analysis of proteins in bare fused-silica capillaries

The analysis of peptides and proteins by CE is often desirable due to low sample consumption and possibilities for nondenaturing yet highly effective separations. However, adsorption to the inner surfaces of fused-silica capillaries often is detrimental to such analyses. This phenomenon is especially pronounced in the analysis of basic proteins and proteins containing exposed positively charged patches. To avoid wall interactions numerous buffer additives and static and dynamic wall coating principles have been devised. We previously showed (J. Chromatogr. A 2004, 1059, 215-222) that CE of the basic protein beta2-glycoprotein was rendered possible by an acidic pretreatment step, and we attributed this observation to the so-called pH hysteresis effect that influences the time for pH equilibration of the capillary wall and thus the effective wall charge and the electroosmotic mobility. We here investigate the effects of different pretreatment techniques on EOF values and on the rate of the deprotonation of silanol groups when performing the electrophoresis at neutral pH. We show the utility of this simple approach for the CE analysis of a number of basic proteins in plain silica capillaries at physiological pH.

Nonaqueous capillary electrophoresis in coated capillaries: An interesting alternative for proteomic applications

This work brings together some contributions for the use of nonaqueous media for proteomic analysis, for both capillary electrophoresis (CE) separation and the preparation of tryptic digests. First, a ternary nonaqueous buffer consisting of 60/30/10 v/v methanol/acetonitrile/acetic acid with 12.5 mmol/L ammonium acetate was optimized for CE separation of the tryptic digest of lysozyme. Lysozyme was chosen as a model system for the protein digestion, which has also been prepared in an organic-rich medium with methanol/50 mmol/L NH(4)HCO(3), pH 8.0 (60/40 v/v). The separation results were compared to in silico (PeptideCutter program) digestion conditions, and high-efficiency peak separation (18 peaks) was obtained in 20 min with an electric field of 350 V/cm. In addition, we have evaluated the stability of a coated capillary with poly-N,N-dimethylacrylamide (60/30 cm total/effective length and 75 microm ID) for over 100 runs of tryptic digest with the nonaqueous background electrolyte solvent system. The migration times for ten selected peptide peaks presented 3-7% relative standard deviation.

Fluorescence detection system for capillary separations utilizing a liquid core waveguide with an optical fibre-coupled compact spectrometer

A fluorescence detection system for capillary liquid separation methods is described. The system is based on a silica capillary coated with a low refractive index fluoropolymer Teflon AF that serves both as a separation channel and as a liquid core waveguide (LCW). A fibre-coupled laser excites separated analytes in a detection point and arising fluorescence is collected at one end of the LCW capillary into the other optical fibre which brings it to a compact charge-coupled device (CCD) array spectrometer installed in a desktop computer. No additional components such as focusing optics or filters are necessary. This system was used for detecting isoelectrically focused fluorescent low-molecular-mass pI (isoelectric point) markers and fluorescein isothiocyanate (FITC) labelled proteins. The ability of the system to acquire fluorescent spectra is also demonstrated.

Polypyrrole-coated capillaries for capillary zone electrophoresis

Fused-silica capillaries are permanently coated by silanization with 3-{[3-(N-pyrrole)-2-hydroxypropyl]amino}propyltriethoxysilane followed by oxidative polymerization of the pyrrole moieties with iron (III) or peroxodisulfate in the presence of chloride, perchlorate, or dextransulfate as anions. This approach allows to modulate the EOF in its magnitude as well as in its direction. With the small anions chloride and perchlorate, the EOF is reversed below pH 5 while with the large dextransulfate polyanions (DS) the EOF is relatively constant over the pH range from 2.5 to 9.4. This can be of advantage at low pH, at which the EOF of uncoated capillaries is close to zero. Application for separation of some herbicides is shown. The lifetime of PP-modified capillaries is satisfactory: the decrease in EOF is less than 3% during 80 analyses (160 min) and less than 5% over three months of storage. The reproducibility of capillary modification is about 5% (RSD of EOF).

Capillary electrophoresis-based analysis of phospholipid and glycosaminoglycan binding by human beta2-glycoprotein I

Human beta2-glycoprotein I (beta2gpI) is a phospholipid and heparin binding plasma glycoprotein involved in autoimmune diseases characterized by blood clotting disturbances (thrombosis) together with the occurrence of autoantibodies against beta2gpI. With the final goal of assessing autoantibody influence on binding interactions of beta2gpI we have studied the development of capillary electrophoresis (CE)-based assays for interactions of negatively charged ligands with beta2gpI. In the development of suitable conditions for analysis at neutral pH of this basic protein (pI about 8) we found the pH hysteresis behavior of fused silica surfaces useful since the protonated surface after an acid pre-wash counteracted protein adsorption efficiently in contrast to more laborious procedures including acrylamide/dimethylacrylamide coatings that did not permit analysis of this particular protein. This simple approach made estimates of heparin-beta2gpI interactions possible and the principle was shown also to work for detection of betagpI binding to anionic phospholipids. Utilizing the pH hysteresis effect may be a simple solution to the adsorption problems often encountered in analyses of proteins by CE.

Application of dodecyldimethyl (2-hydroxy-3-sulfopropyl) ammonium in wall modification for capillary electrophoresis separation of proteins

A zwitterionic surfactant, dodecyldimethyl (2-hydroxy-3-sulfopropyl) ammonium (C12H25N+(CH3)2CH2CHOHCH2SO3-), named dodecyl sulfobetaine (DSB), was used as a novel modifier to coat dynamically capillary walls for capillary electrophoresis separation of basic proteins. The DSB coating suppressed the electroosmotic flow (EOF) in the pH range of 3-12. At high DSB concentration, the EOF was suppressed by more than 8.8 times. The DSB coating also prevented successfully the adsorption of cationic proteins on the capillary wall. Anions, such as Cl-, Br-, I-, SO4(2-), CO3(2-), and ClO4-, could be used as running buffer modifiers to adjust the EOF for better separation of analytes. Using this dynamically coated capillary, a mixture of eight inorganic anions achieved complete separation within 4.2 min with the efficiencies from 24,000 to 1,310,000 plates/m. In the presence of ClO4- as EOF adjustor, the separation of a mixture containing four basic proteins (lysozyme, cytochrome c, alpha-chymotrypsinogen A, and myoglobin) yielded efficiencies of 204,000-896,000 plates/m and recoveries of 88%-98%. Migration time reproducibility of these proteins was less than 0.5% relative standard deviation (RSD) from run to run and less than 3.1% RSD from day to day, showing promising application of this novel modifier in protein separation.

Rapid and sensitive determination of ephedrine and pseudoephedrine by micellar electrokinetic chromatography with on-line regenerating covalent coating

A rapid, sensitive and reproducible micellar electrokinetic chromatographic method using hexamethyldisilazane as on-line regenerating covalent coating was developed for the quantification of ephedrine (E) and pseudoephedrine (PE). E and PE were derivatized with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazol for laser-induced fluorescence detection. The on-line regenerating covalent coating formed a combinative double coating with the subsequently produced dynamic SDS coating. The total coating can be easily removed and conveniently regenerated on-line. The simple coating procedure was described. By a series of optimization, a running buffer of 20 mm Na(2)B(4)O(7) + 16 mm SDS was applied for the separation of the derivatives. Linear relationships for E and PE were obtained in the range of 0.044-6.60 microg mL(-1) (correlation coefficients: 0.9975 for E, 0.9981 for PE), and the detection limits for E and PE were 1.71 and 0.67 ng mL(-1), respectively. The separation speed, the reproducibility and the sensitivity were much improved over those of other capillary electrophoresis methods more recently reported. The method was applied to the analysis of the two alkaloids in traditional herbal preparations with recoveries in the range 92.8-104.8%.

Comparison of native and recombinant chlorite dismutase from Ideonella dechloratans

A detailed comparison between native chlorite dismutase from Ideonella dechloratans, and the recombinant version of the protein produced in Escherichia coli, suggests the presence of a covalent modification in the native enzyme. Although the native and recombinant N- and C-terminal sequences are identical, the enzymes display different electrophoretic mobilities, and produce different peptide maps upon digestion with trypsin and separation of fragments using capillary electrophoresis. Comparison of MALDI mass spectra of tryptic peptides from the native and recombinant enzymes suggests two locations for modification in the native protein. Mass spectrometric analysis of isolated peptides from a tryptic digest of the native enzyme identifies a possible cross-linked dipeptide, suggesting an intrachain cross-link in the parent protein. Spectrophotometric titration of the native enzyme in the denatured state reveals two titrating components absorbing at 295 nm, suggesting the presence of about one tyrosine residue per subunit with an anomalously low pK(a). The EPR spectrum for the recombinant enzyme is different from that of the native enzyme, and contains a substantial contribution of a low-spin species with the characteristics of bis-histidine coordination. These results are discussed in terms of a covalent cross-link between a histidine and a tyrosine sidechain, similar to those found in other heme enzymes operating under highly oxidizing conditions.

A novel double coating for microemulsion electrokinetic chromatography with laser-induced fluorescence detection: as tested with amino acid derivatives

A novel double coating (DC) was developed for fast and reproducible microemulsion electrokinetic chromatography (MEEKC), as tested with separation and determination of amino acids using laser-induced fluorescence (LIF) detection after derivatization with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazol. The simple coating is a combination of a removable covalent layer and a dynamic SDS coating. Hexamethyldisilazane was utilized for the covalent layer that can be regenerated on-line. Compared with previous no-coating method, the analysis time was shortened; and the reproducibility of migration times was improved.

Micellar electrokinetic chromatography with laser-induced fluorescence detection for rapid and sensitive analysis of two new bioactive reagents using dynamic covalent coating

A simple, rapid, selective, and sensitive micellar electrokinetic chromatography (MEKC) with laser-induced fluorescence detection (LIF) method was developed, using hexamethyldisilazane (HMDS) as dynamic covalent coating (DCC), for the analysis of two new bioactive agents N-n-hexyl-N'-(sodium p-aminobenzenesulfonate) thiourea (HXPT) and N-n-undecyl-N'-(sodium p-aminobenzenesulfonate) thiourea (UPT) derivatized with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazole. MEKC methods both not using DCC and using DCC were investigated. In a series of optimization steps, DCC and a running buffer of 20 mM Na2B4O7 + 16 mM SDS + 8% acetonitrile were applied for determination of the derivatives. Linear relationships for HXPT and UPT were obtained in the range of 5 to 100 microM (correlation coefficient: 0.9986 for HXPT, 0.9978 for UPT), and the detection limits for HXPT and UPT were 16.5 and 39.0 ng mL(-1). The sensitivity was improved over that of fluorescence spectroscopy methods. The method was applied to the analysis of the two reagents in lab water waste with recoveries in the range of 95.6-107.5%.

Deviation from Ohm’s law in electric field assisted capillary liquid chromatography

Earlier studies of electric field assisted LC (EF-LC) have shown that the effect on charged analytes of the application of an electric field over a capillary LC column is relatively small. Charged analytes can only be affected by the electric field while present in the mobile phase, which makes the effective time for influence of the electric field t(0) independent of retention time. Because the charged analytes only can be affected for a short time the electric field strength ought to be high in order to increase the impact of the electric field on the separation. We have, however, found that only a relatively low electric field strength can be used in EF-LC when pressure is used as main driving force. The useful field strength was limited by a dramatic increase in the current. This increase in current was found to origin from an increased concentration of buffer ions that have an electrophoretic mobility towards the pumped flow.

Separation of mixtures of acidic and basic peptides at neutral pH

Mixtures of acidic and basic peptides composed of the phosphorylated and nonphosphorylated forms of peptide substrates for kinases and a phosphatase were separated by capillary electrophoresis (CE) in buffer conditions compatible with live mammalian cells. The separation of such mixtures was especially challenging given the high salt and neutral pH of the requisite physiologic buffers. Due to poor peak reproducibility in bare capillaries, several strategies were implemented to improve the electrophoretic separation of the peptide mixtures. Covalent coating of the capillary with the neutral polymer poly(dimethylacrylamide) (PDMA) resulted in a 2-fold improvement in the migration time RSD, but required the use of hydrodynamic flow to overcome the differing electrophoretic mobilities (microeo) of the peptides at neutral pH. This parabolic fluid flow diminished separation efficiency almost 5-fold. Polarity switching during the CE run was used to overcome the opposed microeo, but required the retention of hydrodynamic flow and consequent reduction in separation efficiency. The most efficient separations were seen with the use of covalently-linked, charged polymer coatings to maintain electroosmotic flow and to reduce wall interactions. Two such coatings were tested in the current study. Relative to the PDMA coating, an anionic poly(acrylate) improved the average migration time RSD of six peptides from 1.3 to 0.85% and average separation efficiency from 4.8 to 18.0 (x 10(4) plates/m). Likewise, cationic poly([3-(methacryloylamino)propyl]-trimethylammonium) improved the average migration time RSD of eight peptides from 1.2 to 1.1% and average separation efficiency from 4.8 to 33.9 (x 10(4) plates/m). These findings will be of value to the growing number of applications for analytical techniques utilizing CE for cellular analysis and biochemical studies.

Illustration of a simple and versatile scheme for reversing enantiomeric elution order and facilitating enantiomeric impurity determination in capillary electrophoresis

Determination of enantiomeric purity is most often done under overload conditions, which leads to deformed peaks. In general, the best resolutions are obtained when the small peak appears before the large peak in the electropherogram. To be able to determine the R(+)-impurity in the S(-)-form as well as the S(-)-impurity in the R(+)-form the elution orders have to be reversed. The present paper describes reversal of enantiomeric elution order for the basic analyte propranolol and the acidic analyte ibuprofen. For propranolol, a charged heptakis-(6-sulfo)-beta-cyclodextrin (CD) is used in the background electrolyte. For ibuprofen, a mix of the charged heptakis-(6-sulfo)-beta-CD and the uncharged heptakis-(2,3,6-tri-O-methyl)-beta-CD is used in the background electrolyte. The use of a coated capillary and reversal of the polarity shift the elution order, buffer composition is unchanged in both cases. The enantiomers of propranolol and ibuprofen are well separated on both the coated and uncoated capillaries. Detection limits of enantiomer impurities are investigated using spiked samples of both propranolol and ibuprofen.

Immunoassay of serum alpha(1)-antitrypsin by affinity-probe capillary isoelectric focusing using a fluorescence-labeled recombinant antibody fragment

An immunoassay for human alpha(1)-antitrypsin based on affinity-probe capillary isoelectric focusing (AP-CIEF) is described. The method is based on the separation of free and bound labeled antibody fragments by CIEF with laser-induced fluorescence detection. A recombinant Fab' fragment of mouse immunoglobulin G1 (IgG1) against human alpha(1)-antitrypsin was labeled with tetramethylrhodamine on the single cysteine residue at the hinge region. A single pI isomer of the labeled Fab' was purified by IEF in a slab of agarose gel and was then used as the affinity probe for alpha(1)-antitrypsin. The use of recombinant Fab' considerably simplified the labeling process. Although there was some difficulty in the quantification of native alpha(1)-antitrypsin with the affinity probe, carbamylation of the antigen sample by heat treatment with urea made the complex peaks appear reproducibly and more distinct, thus facilitating the identification and quantification of the complex. The system provided an almost linear response to a pure sample of alpha(1)-antitrypsin over a concentration range of 5-1000 ng/mL and the detection limit extended down to around 2 ng/mL. Alpha(1)-antitrypsin in a serum sample was determined using this system to be 1.2 mg/mL which is comparable to the reported value for the protein.