Surface modification of poly(vinylidene fluoride) by alkaline treatment1. The degradation mechanism

Aryl ether-free polymer electrolytes for electrochemical and energy devices

Anion exchange polymers (AEPs) play a crucial role in green hydrogen production through anion exchange membrane water electrolysis. The chemical stability of AEPs is paramount for stable system operation in electrolysers and other electrochemical devices. Given the instability of aryl ether-containing AEPs under high pH conditions, recent research has focused on quaternized aryl ether-free variants. The primary goal of this review is to provide a greater depth of knowledge on the synthesis of aryl ether-free AEPs targeted for electrochemical devices. Synthetic pathways that yield polyaromatic AEPs include acid-catalysed polyhydroxyalkylation, metal-promoted coupling reactions, ionene synthesis via nucleophilic substitution, alkylation of polybenzimidazole, and Diels-Alder polymerization. Polyolefinic AEPs are prepared through addition polymerization, ring-opening metathesis, radiation grafting reactions, and anionic polymerization. Discussions cover structure-property-performance relationships of AEPs in fuel cells, redox flow batteries, and water and CO2 electrolysers, along with the current status of scale-up synthesis and commercialization.

Leaching kinetics of fluorine during the aluminum removal from spent Li-ion battery cathode materials

The high content of aluminum (Al) impurity in the recycled cathode powder seriously affects the extraction efficiency of Nickel, Cobalt, Manganese, and Lithium resources and the actual commercial value of recycled materials, so Al removal is crucially important to conform to the industrial standard of spent Li-ion battery cathode materials. In this work, we systematically investigated the leaching process and optimum conditions associated with Al removal from the cathode powder materials collected in a wet cathode-powder peeling and recycling production line of spent Li-ion batteries (LIBs). Moreover, we specifically studied the leaching of fluorine (F) synergistically happened along with the removal process of Al, which was not concerned about in other studies, but one of the key factors affecting pollution prevention in the recovery process. The mechanism of the whole process including the leaching of Al and F from the cathode powder was indicated by using NMR, FTIR, and XPS, and a defluoridation process was preliminarily investigated in this study. The leaching kinetics of Al could be successfully described by the shrinking core model, controlled by the diffusion process and the activation energy was 11.14 kJ/mol. While, the leaching of F was attributed to the dissolution of LiPF6 and decomposition of PVDF, and the kinetics associated was described by Avrami model. The interaction of Al and F is advantageous to realize the defluoridation to some degree. It is expected that our investigation will provide theoretical support for the large-scale recycling of spent LIBs.

A PEGylated PVDF Antifouling Membrane Prepared by Grafting of Methoxypolyethylene Glycol Acrylate in Gama-Irradiated Homogeneous Solution

In this study, methoxypolyethylene glycol acrylate (mPEGA) served as a PEGylated monomer and was grafted onto polyvinylidene fluoride (PVDF) through homogeneous solution gamma irradiation. The grafting process was confirmed using several techniques, including infrared spectroscopy (FTIR), thermodynamic stability assessments, and rotational viscosity measurements. The degree of grafting (DG) was determined via the gravimetric method. By varying the monomer concentration, a range of DGs was achieved in the PVDF-g-mPEGA copolymers. Investigations into water contact angles and scanning electron microscopy (SEM) images indicated a direct correlation between increased hydrophilicity, membrane porosity, and higher DG levels in the PVDF-g-mPEGA membrane. Filtration tests demonstrated that enhanced DGs resulted in more permeable PVDF-g-mPEGA membranes, eliminating the need for pore-forming agents. Antifouling tests revealed that membranes with a lower DG maintained a high flux recovery rate, indicating that the innate properties of PVDF could be largely preserved.

Efficient Surface Passivation of Ti-Based Layered Materials by a Nonfluorine Branched Copolymer for Durable and High-Power Sodium-Ion Batteries

There is a crucial need for low-cost energy storage technology based on abundant sodium ions to realize sustainable development with renewable energy resources. Poly(vinylidene fluoride) (PVDF) is applied as a binder in sodium-ion batteries (SIBs). Nevertheless, PVDF is also known to suffer from a larger irreversible capacity, especially when PVDF is used as the binder of negative electrode materials. In this research, a poly(acrylonitrile)-grafted poly(vinyl alcohol) copolymer (PVA-g-PAN) is tested as a binder with Ti-based layered oxides as potential negative electrode materials for SIBs. The chemical stability tests of PVDF and PVA-g-PAN contacted with metallic sodium have been conducted, which reveals that PVDF experiences a defluorination process, while PVA-g-PAN demonstrates excellent chemical stability. Composite electrodes with PVA-g-PAN demonstrate superior electrochemical performances when compared with the PVDF binder, allowing improvement for initial CE, higher rate capability, and long cyclability over 1500 cycles. Detailed characterization of electrodes via soft X-ray photoelectron spectroscopy and field emission scanning electron microscopy demonstrates that the PVA-g-PAN branched structure allows a more uniform distribution of acetylene black with higher coatability, unlocking enhanced rate performances and efficient passivation of Ti-based oxides without the excessive electrolyte decomposition. These findings open a new way to design practical and durable sodium-ion batteries with a high-power density.

Efficient Mineralization of Fluoroelastomers Using Superheated Water in the Presence of Potassium Hydroxide

The mineralization of fluoroelastomers (FKMs) in superheated water in the presence of potassium hydroxide (KOH) was investigated with the aim of developing a methodology for recycling the fluorine element. Two FKMs-an "uncrosslinked FKM", representing a poly(vinylidene fluoride-co-hexafluoropropylene) (poly(VDF-co-HFP)) copolymer with a VDF/HFP molar ratio of 78/22 and a "crosslinked FKM" consisting of this copolymer (cured by peroxide) and carbon black-were treated. The fluorine content of these FKMs was efficiently transformed into F- ions in the reaction solution using low KOH concentrations (0.10-0.50 M) at 200-250 °C. When the uncrosslinked or crosslinked FKMs reacted with aqueous KOH (0.20 M) at a rather low temperature (200 °C) for 18 h, the fluorine content of these FKMs was completely mineralized (both F- yields were 100%). Although the crosslinked FKM contained carbon black, the fluorine mineralization of the FKM was not inhibited. The addition of Ca(OH)2 to the reaction solutions after the superheated water treatment at 250 °C for 6 h with aqueous KOH (0.50 M) led to the production of pure CaF2, identified using X-ray spectroscopy, with 100% and 93% yields for the uncrosslinked and crosslinked FKMs, respectively.

Enhanced Anti-Wetting Methods of Hydrophobic Membrane for Membrane Distillation

Increasing issues of hydrophobic membrane wetting occur in the membrane distillation (MD) process, stimulating the research on enhanced anti-wetting methods for membrane materials. In recent years, surface structural construction (i.e., constructing reentrant-like structures), surface chemical modification (i.e., coating organofluorides), and their combination have significantly improved the anti-wetting properties of the hydrophobic membranes. Besides, these methods change the MD performance (i.e., increased/decreased vapor flux and increased salt rejection). This review first introduces the characterization parameters of wettability and the fundamental principles of membrane surface wetting. Then it summarizes the enhanced anti-wetting methods, the related principles, and most importantly, the anti-wetting properties of the resultant membranes. Next, the MD performance of hydrophobic membranes prepared by different enhanced anti-wetting methods is discussed in desalinating different feeds. Finally, facile and reproducible strategies are aspired for the robust MD membrane in the future.

Effect of Carbonate Source on the Dehydrofluorination Process in Polyvinylidene Fluoride/Alkali Metal Carbonate Composites

In this paper, Raman and X-ray photoelectron spectroscopies were applied to analyze compositional and structural variations of the generated activated carbon (AC), as induced by changing carbonate source in three different types of systems, PVDF/M₂CO₃ (M = Li, Na, and K). According to the variations of I _D/I _G and sp²/sp³ ratios, a strong dependence of the AC structure on the type and content of the initial carbonate was found, determined by practical dehydrofluorination reactions associated with oxygen incorporation in AC and side reactions, because of the property variation induced by the difference in the cation of the carbonate sources. This procedure clarified the process of PVDF dehydrofluorination and the formation of activated carbon, which helps to optimize the material performance of the percolative composite for flexible energy storage applications.

Physicochemical and biological ageing processes of (micro)plastics in the environment: a multi-tiered study on polyethylene

Pollution by plastic and microplastic impacts the environment globally. Knowledge on the ageing mechanisms of plastics in natural settings is needed to understand their environmental fate and their reactivity in the ecosystems. Accordingly, the study of ageing processes is gaining focus in the context of the environmental sciences. However, laboratory-based experimental research has typically assessed individual ageing processes, limiting environmental applicability. In this study, we propose a multi-tiered approach to study the environmental ageing of polyethylene plastic fragments focusing on the combined assessment of physical and biological processes in sequence. The ageing protocol included ultraviolet irradiation in air and in a range of water solutions, followed by a biofouling test. Changes in surface characteristics were assessed by Fourier transform infrared spectroscopy, scanning electron microscopy, and water contact angle. UV radiation both in air and water caused a significant increase in the density of oxidized groups (i.e., hydroxyl and carbonyl) on the plastic surface, whereby water solution chemistry influenced the process both by modulating surface oxidation and morphology. Biofouling, too, was a strong determinant of surface alterations, regardless of the prior irradiation treatments. All biofouled samples present (i) specific infrared bands of new surface functional groups (e.g., amides and polysaccharides), (ii) a further increase in hydroxyl and carbonyl groups, (iii) the diffuse presence of algal biofilm on the plastic surface, and (iv) a significant decrease in surface hydrophobicity. This suggests that biological-driven alterations are not affected by the level of physicochemical ageing and may represent, in real settings, the main driver of alteration of both weathered and pristine plastics. This work highlights the potentially pivotal role of biofouling as the main process of plastic ageing, providing useful technical insights for future experimental works. These results also confirm that a multi-tiered laboratory approach permits a realistic simulation of plastic environmental ageing in controlled conditions.

Spatially Confined Fabrication of Polar Poly(Vinylidene Fluoride) Nanotubes

Polar poly(vinylidene fluoride) (PVDF) nanotubes have attracted significant attention due to their excellent piezoelectric and ferroelectric properties, yet a tunable fabrication of homogeneous polar PVDF nanotubes remains a challenge. Here, a simple method is reported to fabricate polar PVDF nanotubes using anodize aluminum oxide (AAO) membranes as templates that are removed by etching in a potassium hydroxide (KOH) solution and then ageing at room temperature. PVDF nanotubes originally crystallized in the AAO membrane are pure α-crystals with very low crystallinity, yet after being released from the templates, the crystallinity of the nanotubes markedly increases with ageing at room temperature, leading to the formation of β-PVDF crystals in a very short time, with the formation of γ crystals after longer ageing times. A large amount of γ crystals formed when the released PVDF nanotubes are heated to ≈130 °C. The formation of polar PVDF nanotubes released from the AAO templates treated with higher concentrations of alkaline solution results from the reaction of the surface of the PVDF nanotubes with the alkaline solution and structure reorganization under confined conditions. This large-scale preparation of β- and γ-PVDF opens a new pathway to produce polar PVDF nanomaterials.

Brief Review of PVDF Properties and Applications Potential

Currently, there is an ever-growing interest in carbon materials with increased deformation-strength, thermophysical parameters. Due to their unique physical and chemical properties, such materials have a wide range of applications in various industries. Many prospects for the use of polymer composite materials based on polyvinylidene fluoride (PVDF) for scientific and technical purposes explain the plethora of studies on their characteristics "structure-property", processing, application and ecology which keep appearing. Building a broader conceptual picture of new generation polymeric materials is feasible with the use of innovative technologies; thus, achieving a high level of multidisciplinarity and integration of polymer science; its fundamental problems are formed, the solution of which determines a significant contribution to the natural-scientific picture of the modern world. This review provides explanation of PVDF advanced properties and potential applications of this polymer material in its various forms. More specifically, this paper will go over PVDF trademarks presently available on the market, provide thorough overview of the current and potential applications. Last but not least, this article will also delve into the processing and chemical properties of PVDF such as radiation carbonization, β-phase formation, etc.

Analysis of the chemical behavior at the molecular level of lined pipes with fluoropolymers in a sodium hypochlorite production line/bibliographic review

This case study is about finding the best fluoropolymer coating for pipes that resists the sodium hypochlorite continue production, which is one of the most aggressive chemical processes that can lead to molecular attack in reactors made by lined pipes. There are several types of coatings pipe such as fiberglass, polymers and elastomers, but the fluoropolymers which have unique properties that make them resistant to chemical attack. In this production process, the premature deterioration of coating pipes is common, due to the expansion of chlorine at the inlet of the reactor, caused by the reaction of chlorine–sodium hydroxide, this is the critical point of the process. Some problems that we find is the chemical attack in that some fluoropolymers coating suffer premature degradation caused by the chemical compatibility, in this case, we explain in detail the chemical and molecular composition of each of the fluoropolymers and how this change occurs at the molecular level. While the lined pipes are the best economical option for chemicals applications, however, it is important to know the correct coating to ensure a long lifetime and avoid piping changes due to premature degradation. Based on the findings of the chemical resistance of each fluoropolymer under study, it is determined which is the best fluoropolymer that resists continuous production of sodium hypochlorite. Results were obtained by a systematic review of the literature.

Mechanism of gelation in high nickel content cathode slurries for sodium-ion batteries

Sodium-ion batteries are a prospective sustainable alternative to the ubiquitous lithium-ion batteries due to the abundancy of sodium, and their cobalt free cathodes. The high nickel O3-type oxides show promising energy densities, however, a time dependency in the rheological properties of the composite electrode slurries is observed, which leads to inhomogeneous coatings being produced. A combination of electron microscopy and infra-red spectroscopy were used to monitor the O3-oxide surface changes upon exposure to air, and the effect upon the rheology and stability of the inks was investigated. Upon exposure to air, NaOH rather than Na₂CO₃ was observed on the surfaces of the powder through FTIR and EDS. The subsequent gelation of the slurry was initiated by the NaOH and dehydrofluorination with crosslinking of PVDF was observed through the reaction product, NaF. Approximately 15% of the CF bonds in PVDF undergo this dehydrofluorination to form NaF. As observed in the relaxation time of fitted rheological data, the gelation undergoes a three-stage process: a dehydrofluorination stage, creating saturated structures, a crosslinking stage, resulting in the highest rate of gelation, and a final crosslinking stage. This work shows the mechanism for instability of high nickel containing powders and electrode slurries, and presents a new time dependent oscillatory rheology test that can be used to determine the process window for these unstable slurry systems.

Armor-Structured Interconnected-Porous Membranes for Corrosion-Resistant and Highly Permeable Waste Ammonium Resource Recycling

Ammonium recovery from wastewater by gas-permeable membranes is promising but suffers from the tradeoff between membrane stability and permeability under harsh operating conditions. Chemical-resistant membranes display modest permeability due to the poor solubility and processibility; chemically active membranes are easier to be endowed with better permeability however hinder by instability. To resolve such a problem, we cleverly design a novel membrane configuration via one-step solution-electrospinning, with the chemical-active component (low-strength fluorine polymer) as the inner skeleton to construct interconnected porous structures and the chemical-resistant component (high-strength fluorine polymer) as the outer armor to serve as a protective layer. Due to the significantly enhanced mass transfer coefficient, the interconnected-porous armor-structured membrane exhibited much higher permeability for NH₄⁺-N recovery, which was 1.4 and 5 times that of the traditional PTFE membrane and PP membrane, respectively. Through long-term intermittent and consecutive experiments, the reusability and durability of the armor-structured nanofibrous membrane were verified. When treating actual hoggery wastewater with complicated water quality, the armor-structured nanofibrous membrane also displayed robust stable performance with excellent antiwettability. The mechanisms of membrane formation, corrosion resistance, and mass transfer were discussed in detail.

Flat PVDF Membrane with Enhanced Hydrophobicity through Alkali Activation and Organofluorosilanisation for Dissolved Methane Recovery

A three-step surface modification consisting of activation with NaOH, functionalisation with a silica precursor and organofluorosilane mixture (FSiT), and curing was applied to a poly(vinylidene fluoride) (PVDF) membrane for the recovery of dissolved methane (D-CH4) from aqueous streams. Based on the results of a statistical experimental design, the main variables affecting the water contact angle (WCA) were the NaOH concentration and the FSiT ratio and concentration used. The maximum WCA of the modified PVDF (mPVDFmax) was >140° at a NaOH concentration of 5%, an FSiT ratio of 0.55 and an FSiT concentration of 7.2%. The presence of clusters and a lower surface porosity of mPVDF was detected by FESEM analysis. In long-term stability tests with deionised water at 21 L h−1, the WCA of the mPVDF decreased rapidly to around 105°, similar to that of pristine nmPVDF. In contrast, the WCA of the mPVDF was always higher than that of nmPVDF in long-term operation with an anaerobic effluent at 3.5 L h−1 and showed greater mechanical stability, since water breakthrough was detected only with the nmPVDF membrane. D-CH4 degassing tests showed that the increase in hydrophobicity induced by the modification procedure increased the D-CH4 removal efficiency but seemed to promote fouling.

Interfacial reactions in lithia-based cathodes depending on the binder in the electrode and salt in the electrolyte

Lithia (Li₂O)-based cathodes, utilizing oxygen redox reactions for obtaining capacity, exhibit higher capacity than commercial cathodes. However, they are highly reactive owing to superoxides formed during charging, and they enable more active parasitic (side) reactions at the cathode/electrolyte and cathode/binder interfaces than conventional cathodes. This causes deterioration of the electrochemical performance limiting commercialization. To address these issues, the binder and salt for electrolyte were replaced in this study to reduce the side reaction of the cells containing lithia-based cathodes. The commercially used polyvinylidene fluoride (PVDF) binder and LiPF₆ salt in the electrolyte easily generate such reactions, and the subsequent reaction between PVDF and LiOH (from decomposition of lithia) causes slurry gelation and agglomeration of particles in the electrode. Moreover, the fluoride ions from PVDF promote side reactions, and LiPF₆ salt forms POF₃ and HF, which cause side reactions owing to hydrolysis in organic solvents containing water. However, the polyacrylonitrile (PAN) binder and LiTFSI salt decrease these side reactions owing to their high stability with lithia-based cathode. Further, thickness of the interfacial layer was reduced, resulting in decreased impedance value of cells containing lithia-based cathodes. Consequently, for the same lithia-based cathodes, available capacity and cyclic performance were increased owing to the effects of PAN binder and LiTFSI salt in the electrolyte.

Enhanced Electrochemical Performance of Ni-Rich Cathodes by Neutralizing Residual Lithium with Acid Compounds

Surficial residual LiOH and/or Li₂CO₃ on Ni-rich cathodes arouse troubles for their practical applications, such as slurry gelling and durability degrading. To assure acceptable performance, the strategy of "washing and heat treatment" is generally utilized to remove them in industry, which is unavoidable to generate plenty of wastewater. In this work, we investigated the mechanism of slurry gelling caused by residual lithium on Ni-rich materials and then proposed a simple and efficient method to convert the detrimental residual lithium to the useful surface layer of LiF or LiBOB at 220 °C without water washing. As a result, the basicity of modified samples is lowered to 11.48 and 11.60 from 12.05 of the pristine, respectively. Owing to the beneficial effect of the surface layer, the treated samples deliver a discharge capacity of 189.5 and 187.9 mA h g^-1 and retain 84.1 and 82.8% of the initial capacity under 1 C after 300 cycles, which is much better than that of the untreated material (57.8%). The comprehensive performances of the modified samples in this work are very close to those of the material treated with the industrial method, demonstrating the advantage of this strategy to further reduce the cost of material production.

A Polymer-Based Matrix for Effective SALDI Analysis of Lipids

Surface-assisted laser desorption/ionization (SALDI) has become an attractive branch of matrix-assisted laser desorption/ionization (MALDI) and has been successfully applied for the detection of small molecules due to the lack of the interference of matrix. Herein, the low-cost and highly accessible polyvinylidene fluoride (PVDF) was modified using a facile alkali treatment and investigated as a SALDI matrix. The modified PVDF has a strong optical absorption and can be applied as a dual-mode substrate for both SALDI MS and SALDI imaging analysis. Modified PVDF powder showed superior performance in SALDI MS analysis of lipids, with good reproducibility, high sensitivity, and low background interference, especially for triacylglycerols (TAGs) and fatty acids. Additionally, the lipids in raw and extracted serum were both successfully determined with modified PVDF powder. A modified PVDF membrane (m-PVDF-m) showed excellent ability in lipids imaging in tissues due to its flat surface, mass signal enhancement, and elimination of matrix coating. The distribution of several TAGs and cholesteryl esters on mouse kidney section was presented by SALDI imaging directly on m-PVDF-m. These results demonstrated that modified PVDF materials presented exciting opportunities as matrices for the first time in SALDI MS acquisition and SALDI imaging.

On the Solubility and Stability of Polyvinylidene Fluoride

This literature review covers the solubility and processability of fluoropolymer polyvinylidine fluoride (PVDF). Fluoropolymers consist of a carbon backbone chain with multiple connected C-F bonds; they are typically nonreactive and nontoxic and have good thermal stability. Their processing, recycling and reuse are rapidly becoming more important to the circular economy as fluoropolymers find widespread application in diverse sectors including construction, automotive engineering and electronics. The partially fluorinated polymer PVDF is in strong demand in all of these areas; in addition to its desirable inertness, which is typical of most fluoropolymers, it also has a high dielectric constant and can be ferroelectric in some of its crystal phases. However, processing and reusing PVDF is a challenging task, and this is partly due to its limited solubility. This review begins with a discussion on the useful properties and applications of PVDF, followed by a discussion on the known solvents and diluents of PVDF and how it can be formed into membranes. Finally, we explore the limitations of PVDF's chemical and thermal stability, with a discussion on conditions under which it can degrade. Our aim is to provide a condensed overview that will be of use to both chemists and engineers who need to work with PVDF.

Do membrane filtration systems in drinking water treatment plants release nano/microplastics?

Drinking water treatment plants (DWTPs) are thought to be able to remove many micropollutants including nanoplastics (NPs) and microplastics (MPs). However, few studies have focused on the water treatment process itself producing NPs and/or MPs. This paper discussed the possibility of releasing NPs and MPs from organic membranes in drinking water treatment plants. The effects of physical cleaning, chemical agents, mechanical stress, aging, and wear on the possibility of membrane breach during long-term use were analyzed. Further analysis based on membrane aging mechanisms and material properties revealed that the membrane filtration systems could release NPs/MPs to drinking water supply networks. Although the toxicity of membrane materials to human body needs further study, the action that should be taken to treat the release of NPs/MPs in DWTPs cannot be ignored: (1) in-depth study of the generation and release mechanisms of NPs/MPs; (2) reconsideration of membrane life cycle design; (3) determination of NPs/MPs concentration limits in drinking water through toxicity assessment; (4) accelerating development of biomembrane and inorganic membrane materials; and (5) unification of NPs/MPs sampling and testing standard. Accordingly, more research needs to be conducted to investigate the release of NPs and/or MPs from DWTPs.

Gamma Radiation-Induced Unsaturated P(VDF-CTFE) Membranes with Improved Mechanical Properties

Poly(vinylidene fluoride-chlorotrifluoroethylene) (P(VDF-CTFE)) membranes were prepared by drop-casting with tetrahydrofuran (THF), and were then radiated by a low dose of gamma radiation without any other reagents. The apparent colour of the freshly prepared film was a semi-transparent white, which gradually darkened and finally turned black after 10.2kGy gamma radiation. Meanwhile, the yield and breaking strength of the membrane both improved. X-Ray diffraction (XRD) spectra showed that the structure of the microcrystal of the irradiated P(VDF-CTFE)-THF membrane was not changed. FT-IR analysis showed that the structure of the newly formed double bonds was dominated by –CF2–CF=CH–CF2–, which was formed by both dehydrofluorination and dehydrochlorination. This structure was further confirmed by 1H NMR spectra. The intermediates, such a radical-containing double bonds (–(CF=CH)n–C•F–) formed in this process were traced by electron paramagnetic resonance (EPR) spectroscopy. The thermal and mechanical properties were studied by gel permeation chromatography (GPC), thermogravimetric analysis (TGA), stress–strain and dynamic mechanical analysis (DMA), and all the changes of microstructure and optimization of apparent properties were not found in the corresponding membrane prepared by a solution-cast method with ethyl acetate (EtOAc). Therefore, this paper briefly analyses the probable mechanism of using low dose of gamma radiation to improve the mechanical properties of the P(VDF-CTFE) film prepared with THF.

Impacts of Sulfuric Acid on the Stability and Separation Performance of Polymeric PVDF-Based Membranes at Mild and High Concentrations: An Experimental Study

This study investigated the effects of an aqueous acidic solution at typical concentrations on polymeric polyvinylidene fluoride (PVDF)-based membranes. Flat-sheet PVDF-based membranes were completely embedded in sulfuric acid at varying concentrations. The effect of the acid concentration after a prolonged exposure time on the chemical, mechanical and physical properties of the membrane were checked via FE-SEM, EDX (Energy-Dispersive Spectrometer), FTIR, XRD, tensile strength, zeta potential, contact angle, porosity, pure water flux measurement and visual observation. The result reveals prompt initiation of reaction between the PVDF membrane and sulfuric acid, even at a mild concentration. As the exposure time extends with increasing concentration, the change in chemical and mechanical properties become more pronounced, especially in the morphology, although this was not really noticeable in either the crystalline phase or the functional group analyses. The ultimate mechanical strength decreased from 46.18 ± 0.65 to 32.39 ± 0.22 MPa, while the hydrophilicity was enhanced due to enlargement of the pores. The flux at the highest concentration and exposure period increased by 2.3 times that of the neat membrane, while the BSA (Bovine Serum Albumin) rejection dropped by 55%. Similar to in an alkaline environment, the stability and performance of the PVDF-based membrane analyzed in this study manifested general deterioration.

Controlling Residual Lithium in High-Nickel (>90 %) Lithium Layered Oxides for Cathodes in Lithium-Ion Batteries

The rampant generation of lithium hydroxide and carbonate impurities, commonly known as residual lithium, is a practical obstacle to the mass-scale synthesis and handling of high-nickel (>90 %) layered oxides and their use as high-energy-density cathodes for lithium-ion batteries. Herein, we suggest a simple in situ method to control the residual lithium chemistry of a high-nickel lithium layered oxide, Li(Ni_0.91 Co_0.06 Mn_0.03 )O₂ (NCM9163), with minimal side effects. Based on thermodynamic considerations of the preferred reactions, we systematically designed a synthesis process that preemptively converts residual Li₂ O (the origin of LiOH and Li₂ CO₃ ) into a more stable compound by injecting reactive SO₂ gas. The preformed lithium sulfate thin film significantly suppresses the generation of LiOH and Li₂ CO₃ during both synthesis and storage, thereby mitigating slurry gelation and gas evolution and improving the cycle stability.

Integrating cationic metal-organic frameworks with ultrafiltration membrane for selective removal of perchlorate from Water

We design a novel cationic metal-organic framework hybrid ultrafiltration polyvinylidene fluoride membrane (PVA/Cu-iMOFs/PVDF-0.05) and report its unique capture of aqueous perchlorate (ClO₄^-) at ppm-level. This membrane outperformed traditional adsorption materials and exhibited a specific affinity toward ClO₄^- in the presence of various competing anions at greater levels (up to a concentration ratio of 20). In the batch experiment, the ClO₄^- removal ratio reached 99.6% over a wide pH range (3˜10). Membrane filtration by using a 12.56 cm² PVA/Cu-iMOFs/PVDF-0.05 membrane could effectively treat 4.71 L of ClO₄^--contaminated water before breakthrough occurred, while maintaining a satisfactory permeability (˜627.32 L/(m² h bar)) and antifouling property. The exhausted membrane could easily be regenerated in aminoethanesulfonic acid solution for repeated use with a negligible decrease in capacity. Moreover, the membrane showed excellent long-term stability in a cross-flow filtration process due to the amido bond between the Cu-iMOFs and membrane surface as well as the "protection" of polyvinyl alcohol. Selective and reversible ion-exchange between the sulfonic acid (R-SO₃) ligands of Cu-iMOFs and tetrahedral oxo-anionic species was verified to be the pathway for ClO₄^- trapping. Thus, other problematic elements that also occur in tetrahedral form in water can be removed by this method.

Reduction of liquid terminated-carboxyl fluoroelastomers using NaBH4/SmCl3

Using a simple one-pot method, the reduction of liquid terminated-carboxyl fluoroelastomers (LTCFs) by sodium borohydride and samarium chloride (NaBH₄/SmCl₃) was successfully realized and liquid terminated-hydroxyl fluoroelastomers (LTHFs) were obtained. The structure and functional group content of LTCFs and LTHFs were analyzed by FTIR, ¹H-NMR, ¹⁹F-NMR and chemical titration. The results showed that –C Created by potrace 1.16, written by Peter Selinger 2001-2019 ]]> C– and carboxyl groups of LTCFs were reduced efficiently, the reduction rate reached 92% under optimum reaction conditions. Compared with other frequently-used metal chlorides, SmCl₃ with a high coordination number could increase the reduction activity of NaBH₄ more effectively and the reduction mechanism was explored.

A facile method using NaBH₄/SmCl₃ allows for reduction of liquid terminated-carboxyl fluoroelastomers (LTCFs) in excellent yields and provides an attractive potential scheme for the reduction of other carboxyl organic compounds.