Volumetric contraction and methacrylate conversion in photo-polymerized amorphous calcium phosphate/methacrylate composites

Antimicrobial, biocompatibility, and physicochemical properties of novel adhesive methacrylate dental monomers

For the advancement of Class V restoratives, our goal was to evaluate the physicochemical and mechanical properties, antimicrobial functionality, and cytotoxic potential of novel antimicrobial copolymers. 5-Carboxy-N-(2-(methacryloyloxy)ethyl)-N,N-dimethylpentan-1-aminium bromide (AMadh1) and 10-carboxy-N-(2-(methacryloyloxy)ethyl)-N,N-dimethyldecan-1-aminium bromide (AMadh2) were incorporated into light-curable urethane dimethacrylate, polyethylene glycol–extended urethane dimethacrylate, ethyl 2-(hydroxymethyl) acrylate resin (UPE resin). In the AMadhs-UPE resin, the hydrophobic/hydrophilic balance, degree of vinyl conversion, flexural strength, elastic modulus, and shear bond strength were assessed. Antimicrobial properties were measured using Streptococcus mutans (planktonic and biofilm). Cytotoxicity was tested using human gingival fibroblasts and mouse connective tissue fibroblasts (ATCC® CCL-1™) exposed to two-fold serial dilutions (≤10.6 mmol/L AMadh1 or ≤8.8 mmol/L AMadh2). At 10% mass of AMadh, the attained degree of vinyl conversion values (AMadh1 = 90.1% and AMadh2 = 88.5%) were not statistically different from the UPE resin (88.1%). At both AMadh levels, the flexural strength was reduced in a dose-dependent manner. Elastic modulus and contact angle were not significantly affected by AMadh1. Variations in elastic modulus and contact angle were observed with AMadh2; however, this does not disqualify it in future design of Class V restoratives. Compared to UPE resin, AMadh1-UPE and AMadh2-UPE (10% mass) copolymers reduced S. mutans biofilm 4.2- and 1.6-fold, respectively (p ≤ 0.006). In direct contact with human gingival fibroblasts or ATCC CCL-1 cells, at biologically relevant concentrations, the AMadhs did not adversely affect cell viability or their metabolic activity. This effort addresses a significant oral health issue associated with elderly populations. Its successful completion is expected to yield dental restoratives with well-controlled biofunction.

Remineralizing amorphous calcium phosphate based composite resins: the influence of inert fillers on monomer conversion, polymerization shrinkage, and microhardness

Aim

To determine if the addition of inert fillers to a bioactive dental restorative composite material affects its degree of conversion (DC), polymerization shrinkage (PS), and microhardness (HV).

Methods

Three amorphous calcium phosphate (ACP)-based composite resins: without added fillers (0-ACP), with 10% of barium-glass fillers (Ba-ACP), and with 10% of silica fillers (Si-ACP), as well as commercial control (Ceram•X, Dentsply DeTrey) were tested in laboratory conditions. The amount of ACP (40%) and the composition of the resin mixture (based on ethoxylated bisphenol A dimethacrylate) was the same for all ACP materials. Fourier transform infrared spectroscopy was used to determine the DC (n = 40), 20 min and 72 h after polymerization. Linear PS and Vickers microhardness (n = 40) were also evaluated. The results were analyzed by paired samples t test, ANOVA, and one-way repeated measures ANOVA with Student-Newman-Keuls or Tukey’s post-hoc test (P = 0.05).

Results

The addition of barium fillers significantly increased the DC (20 min) (75.84 ± 0.62%) in comparison to 0-ACP (73.92 ± 3.08%), but the addition of silica fillers lowered the DC (71.00 ± 0.57%). Ceram•X had the lowest DC (54.93 ± 1.00%) and linear PS (1.01 ± 0.24%) but the highest HV (20.73 ± 2.09). PS was significantly reduced (P < 0.010) in both Ba-ACP (1.13 ± 0.25%) and Si-ACP (1.17 ± 0.19%) compared to 0-ACP (1.43 ± 0.21%). HV was significantly higher in Si-ACP (12.82 ± 1.30) than in 0-ACP (10.54 ± 0.86) and Ba-ACP (10.75 ± 0.62) (P < 0.010).

Conclusion

Incorporation of inert fillers to bioactive remineralizing composites enhanced their physical-mechanical performance in laboratory conditions. Both added fillers reduced the PS while maintaining high levels of the DC. Silica fillers additionally moderately improved the HV of ACP composites.

Structural and dynamical studies of acid-mediated conversion in amorphous-calcium-phosphate based dental composites

OBJECTIVE

To investigate the complex structural and dynamical conversion process of the amorphous-calcium-phosphate (ACP)-to-apatite transition in ACP based dental composite materials.

METHODS

Composite disks were prepared using zirconia hybridized ACP fillers (0.4 mass fraction) and photo-activated Bis-GMA/TEGDMA resin (0.6 mass fraction). We performed an investigation of the solution-mediated ACP-to-apatite conversion mechanism in controlled acidic aqueous environment with in situ ultra-small angle X-ray scattering based coherent X-ray photon correlation spectroscopy and ex situ X-ray diffraction, as well as other complementary techniques.

RESULTS

We established that the ACP-to-apatite conversion in ACP composites is a two-step process, owing to the sensitivity to local structural changes provided by coherent X-rays. Initially, ACP undergoes a local microstructural rearrangement without losing its amorphous character. We established the catalytic role of the acid and found the time scale of this rearrangement strongly depends on the pH of the solution, which agrees with previous findings about ACP without the polymer matrix being present. In the second step, ACP is converted to an apatitic form with the crystallinity of the formed crystallites being poor. Separately, we also confirmed that in the regular Zr-modified ACP the rate of ACP conversion to hydroxyapatite is slowed significantly compared to unmodified ACP, which is beneficial for targeted slow release of functional calcium and phosphate ions from dental composite materials.

SIGNIFICANCE

For the first time, we were able to follow the complete solution-mediated transition process from ACP to apatite in this class of dental composites in a controlled aqueous environment. A two-step process, suggested previously, was conclusively identified.

Ultra-small-angle X-ray scattering-X-ray photon correlation spectroscopy studies of incipient structural changes in amorphous calcium phosphate-based dental composites

The local structural changes in amorphous calcium phosphate (ACP)-based dental composites were studied under isothermal conditions using both static, bulk measurement techniques and a recently developed methodology based on combined ultra-small angle X-ray scattering-X-ray photon correlation spectroscopy (USAXS-XPCS), which permits a dynamic approach. While results from conventional bulk measurements do not show clear signs of structural change, USAXS-XPCS results reveal unambiguous evidence for local structural variations on a similar time scale to that of water loss in the ACP fillers. A thermal-expansion-based simulation indicates that thermal behavior alone does not account for the observed dynamics. Together, these results suggest that changes in the water content of ACP affect the composite morphology due to changes in ACP structure that occur without an amorphous-to-crystalline conversion. It is also noted that biomedical materials research could benefit greatly from USAXS-XPCS, a dynamic approach.

Polymerization shrinkage and stress development in amorphous calcium phosphate/urethane dimethacrylate polymeric composites

This study explores how substituting a new high molecular mass oligomeric poly(ethylene glycol) extended urethane dimethacrylate (PEG-U) for 2-hydroxyethyl methacrylate (HEMA) in photo-activated urethane dimethacrylate (UDMA) resins affects degree of vinyl conversion (DC), polymerization shrinkage (PS), stress development (PSSD) and biaxial flexure strength (BFS) of their amorphous calcium phosphate (ACP) composites. The composites were prepared from four types of resins (UDMA, PEG-U, UDMA/HEMA and UDMA/PEG-U) and zirconia-hybridized ACP. Introducing PEG-U improved DC while not adversely affecting PS, PSSD and the BFS of composites. This improvement in DC is attributed to the long, more flexible structure between the vinyl groups of PEG-U and its higher molecular mass compared to poly(HEMA). The results imply that PEG-U has the potential to serve as an alternative to HEMA in dental and other biomedical applications.

Structure-Composition-Property Relationships in Polymeric Amorphous Calcium Phosphate-Based Dental Composites

Our studies of amorphous calcium phosphate (ACP)-based materials over the last decade have yielded bioactive polymeric composites capable of protecting teeth from demineralization or even regenerating lost tooth mineral. The anti-cariogenic/re-mineralizing potential of these ACP composites originates from their propensity, when exposed to the oral environment, to release in a sustained manner sufficient levels of mineral-forming calcium and phosphate ions to promote formation of stable apatitic tooth mineral. However, the less than optimal ACP filler/resin matrix cohesion, excessive polymerization shrinkage and water sorption of these experimental materials can adversely affect their physicochemical and mechanical properties, and, ultimately, limit their lifespan. This study demonstrates the effects of chemical structure and composition of the methacrylate monomers used to form the matrix phase of composites on degree of vinyl conversion (DVC) and water sorption of both copolymers and composites and the release of mineral ions from the composites. Modification of ACP surface via introducing cations and/or polymers ab initio during filler synthesis failed to yield mechanically improved composites. However, moderate improvement in composite’s mechanical stability without compromising its remineralization potential was achieved by silanization and/or milling of ACP filler. Using ethoxylated bisphenol A dimethacrylate or urethane dimethacrylate as base monomers and adding moderate amounts of hydrophilic 2-hydroxyethyl methacrylate or its isomer ethyl-α-hydroxymethacrylate appears to be a promising route to maximize the remineralizing ability of the filler while maintaining high DVC. Exploration of the structure/composition/property relationships of ACP fillers and polymer matrices is complex but essential for achieving a better understanding of the fundamental mechanisms that govern dissolution/re-precipitation of bioactive ACP fillers, and, ultimately, the suitability of the composites for clinical evaluation.

AMORPHOUS CALCIUM PHOSPHATE COMPOSITES AND THEIR EFFECT ON COMPOSITE-ADHESIVE-DENTIN BONDING

This study evaluates the bond strength and related properties of photo-polymerizable, remineralizing amorphous calcium phosphate (ACP) polymeric composite-adhesive systems to dentin after various periods of aqueous aging at 37 °C. An experimental ACP base and lining composite was made from a photo-activated resin comprising 2,2-bis[p-(2'-hydroxy-3'-methacryloxypropoxy)phenyl]propane (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA), 2-hydroxyethyl methacrylate (HEMA) and zirconyl dimethacrylate (ZrDMA); designated BTHZ. An experimental orthodontic composite was formulated from a photo-activated resin comprising ethoxylated bisphenol A dimethacrylate (EBPADMA), TEGDMA, HEMA and methacryloxyethyl phthalate (MEP); designated ETHM. In both composite series three fillers were compared: 1) freshly precipitated zirconium-modified ACP freshly precipitated (as-prepared Zr-ACP), 2) milled Zr-ACP and 3) an ion-leachable fluoride glass. In addition to the shear bond strength (SBS), work to fracture and failure modes of the orthodontic composites were determined. The SBS of the base and lining ACP composites appeared unaffected by filler type or immersion time. In the orthodontic ACP composite series, milled ACP composites showed initial mechanical advantages over as-prepared ACP composites, and produced higher incidence of a failure mode consistent with stronger adhesion. After six months of aqueous exposure, 80 % of specimens failed at the dentin-primer interface, with a 42 % overall reduction in bond strength. BTHZ and ETHM based ACP composites are potentially effective anti-demineralizing-remineralizing agents with possible clinical utility as protective base-liners and orthodontic cements, respectively. The analysis of the bond strength and failure modalities suggests that milled ACP composites may offer greater potential in clinical applications.

The use of amorphous calcium phosphate composites as bioactive basing materials: their effect on the strength of the composite/adhesive/dentin bond

BACKGROUND

Amorphous calcium phosphate (ACP) composites release calcium and phosphate ions in aqueous environments, which may lead to deposition of apatitic mineral in tooth structure. The authors evaluate the strength of the composite/adhesive/dentin bond shear bond strength (SBS) for ACP basing-composites after various periods of water aging.

METHODS

The authors made the experimental composites by using two resin matrices with various ACPs or a commercial strontium ion-leachable glass. They applied successive coats of a dentin adhesive and basing composite to an acid-etched dentin surface and photopolymerized them. They added a commercial resin-based composite and light cured it. They determined the specimens' SBS after they were aged in water for various periods at 37 degrees C.

RESULTS

The SBS of the ACP composites was 18.3 +/- 3.5 megapascals, independent of filler type, resin composition and water-aging interval. After 24 hours of water aging, 92.6 percent of surfaces showed the adhesive failure. After two weeks of water aging, adhesive/cohesive failures were predominant in unmilled and milled ACP composites.

CONCLUSIONS

The SBS of ACP composites appears to be unaffected by filler type or immersion time for up to six months. The type of adhesive failure occurring with prolonged aqueous exposure is affected by filler type.

CLINICAL IMPLICATIONS

These materials may be effective remineralizing/antidemineralizing agents and may be clinically applicable as adhesives, protective liners and bases, orthodontic cements and pit-and-fissure sealants.

Effect of Chemical Structure and Composition of the Resin Phase on Vinyl Conversion of Amorphous Calcium Phosphate-filled Composites

The objective of this study was to elucidate the effect of chemical structure and composition of the polymer matrix on the degree of vinyl conversion (DC) of copolymers (unfilled resins) and their amorphous calcium phosphate (ACP) composites attained upon photo-polymerization. The DC can also be an indicator of the relative potential of these polymeric materials to leach out into the oral environment un-reacted monomers that could adversely affect their biocompatibility. The following resins were examined: 1) 2,2-bis[p-(2'-hydroxy-3'-methacryloxypropoxy)phenyl]propane (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) (1:1 mass ratio; BT resin) combined with hydroxyethyl methacrylate (HEMA; BTH resin) and with HEMA and zirconyl dimethacrylate (BTHZ resin), 2) urethane dimethacrylate (UDMA)/HEMA resins, and 3) pyromellitic glycerol dimethacrylate (PMGDMA)/TEGDMA (PT resin). To make composite specimens, resins were mixed with a mass fraction of 40 % zirconia-hybridized ACP. Copolymers and their composites were evaluated by near infra-red spectroscopy for DC after 1 d and 28 d post-cure at 23 °C. Inclusion of HEMA into the BT and UDMA resins yielded copolymers and composites with the highest DCs. The significantly lower DCs of PT copolymers and their composites are attributed to the rigid aromatic core structure, tetra-vinyl functionality and limited methacrylate side-chain flexibility of the surface-active PMGDMA monomer. There was, however, an increase in the 28 d DC for the PT materials as there was for the BTHZ system. Surprisingly, the usual decrease observed in DC in going from unfilled polymer to composite was reversed for the PT system.

Quantum-Mechanical QSPR Models for Polymerization Volume Change of Epoxides and Methacrylates Based on Mercury Dilatometry Results

Polymerization volume change (PVC) was measured systematically using mercury dilatometry for 41 epoxide and methacrylate monomers with quartz filler. Quantitative structure property relationship (QSPR) models were developed based on this previously unreported data to gain insight in the data collection method for future models. Successful models included only data from those samples which polymerized to hardness. The most significant descriptors in these models related to monomer reactivity. In contrast, PVC data collected under experimental conditions which maximized monomer conversion resulted in descriptors describing size and branching, indicating conversion must be considered for future PVC measurements. A Rule of Mixtures (ROM) correction term improved correlations of the dilatometer data with varying quartz content, and an adjustment for conversion may similarly enable inclusion of data which had not polymerize to hardness.

Properties of a Dental Resin Composite with a Spherical Inorganic Filler

Of the materials tested in this study, the spherical filler composite (Estelite Σ) had similar properties as the nano-composite (Filtek Supreme). Thus, Estelite Σcan be used in anterior regions and restricted posterior restorations. All the materials had a similar shrinkage pattern, in that about 99% of the shrinkage occurred prior to 24 hours; thus, for direct resin composite restorations, a strong initial bonding strength with bonding agent would be necessary.

Dental composites based on amorphous calcium phosphate - resin composition/physicochemical properties study

This study explores how the resin composition/structure affects the physicochemical properties of copolymers and their amorphous calcium phosphate (ACP)-filled composites. A series of photo-polymerizable binary and ternary matrices are formulated utilizing 2,2-bis[ p-(2(')-hydroxy-3(')methacryloxypropoxy)phenyl]propane, 2,2-bis[ p-(2(')-methacryloxypropoxy)phenyl]-propane (EBPADMA), or a urethane dimethacrylate as base monomers, and triethylene glycol dimethacrylate or hexamethylene dimethacrylate (HmDMA) with or without 2-hydroxyethyl methacrylate (HEMA) as diluent monomer. Unfilled copolymers and composites filled with 40% by mass zirconia-hybridized ACP are evaluated for biaxial flexure strength (BFS), degree of conversion (DC), mineral ion release, polymerization shrinkage (PS), and water sorption (WS). The average DC values are 82-94% and 74-91% for copolymers and composites, respectively. Unrelated to the resin composition, the PS values of composites are up to 8.4 vol. % and the BFS values of wet composite specimens are on average 51 +/- 8 MPa. The maximum WS values attained in copolymers and composites reach 4.8 mass%. Inclusion of hydrophobic HmDMA monomer in the matrices significantly reduces the WS. The levels of Ca and PO(4) released from all types of composites are significantly above the minimum necessary for the re-deposition of apatite to occur. Elevated Ca, and to a lesser extent PO(4) release, is observed in HEMA-containing, ternary EBPADMA formulations. Further resin reformulations may be needed to improve the PS of composite specimens. Poor dispersion of ;as-synthesized' ACP within the composite contributes to their inferior mechanical performance.

Synthesis of low-shrinkage polymerizable methacrylate liquid-crystal monomers

As a part of the continuous pursuit to develop an ideal resinous dental restorative material for use in large posterior cavity restorations, this article reports the easy, high-yield synthesis and the incredibly low polymerization shrinkage property of a new bifunctional liquid crystal (LC) monomer. This new polymerizable nematic liquid crystal is the next higher homolog of the acrylate monomer reported in a previous work.1 It remains liquid crystalline between room and mouth temperatures and can be polymerized to isotropic polymer with the use of the same visible light inhibitor system as used with conventional monomers. The structure of this new monomer has been confirmed to be 2-(t-butyl), 1,4-bis-[4-(6-methacryloxy-hexan-1-oxy)-benzoyloxy]-benzene. Unlike the synthesis of its acrylate homolog, when the same procedure is adopted for the synthesis of this compound, the recovery of the product is not split by a sizable amount of the by-product. Therefore, the reaction is cleaner, with high yield and a less labor-intensive purification procedure. Thus, the synthetic methodology has the potential for easy commercial scale-up. The monomer (V) polymerizes at room temperature with a shrinkage of about 2 vol %, as compared to > 8 vol % for conventional control (GTE), at similar degrees of conversion.

Effect of chemical structure and composition of the resin phase on mechanical strength and vinyl conversion of amorphous calcium phosphate-based composites

The mechanical properties of recently developed bioactive, antidemineralizing/remineralizing, amorphous calcium phosphate (ACP)-based composites need improvement. The objective of this study was to elucidate the effect of structure and composition of resins on the biaxial flexure strength (BFS) and the degree of conversion (DC) of composites attained after photo-polymerization. Two series of 2,2-bis[p-(2'-hydroxy-3'-methacryloxypropoxy)phenyl]propane (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA)/X (X being a neutral or acidic comonomer) ternary resins were prepared and mixed with a mass fraction of 40% of zirconia-hybridized ACP. Both unfilled copolymers and their composites were evaluated for BFS (dry and wet specimens after 2 weeks of immersion in buffered saline) and for DC (after 24 h at 23 degrees C). It was found that for the neutral X monomers, no correlation existed between the hydrophobic/hydrophilic character of the X monomer and the BFS values of the immersed composites. A flexible monomethacrylate yielded copolymers and composites with the highest DC. For the resins utilizing the acidic comonomers, methacrylic acid and mono-4-(methacryloyloxy) ethyltrimellitate (4MET), dry composites with improved BFS values were obtained. 4MET composites exhibited the least loss of strength of all the ternary resin ACP materials. The effect of acidic X on DC was most pronounced for maleic acid copolymers.

Synthesis of low-shrinkage polymerizable liquid-crystal monomers

Polymerization shrinkage remains a major barrier to the universal use of resin restorative in large posterior cavity preparations. A new bifunctional liquid crystal (LC) monomer, 2-(t-butyl), 1,4-bis-[4-(6-acryloxy-hexane-1-oxy)-benzoyloxy] benzene, with exceptionally low polymerization shrinkage, has recently been discovered. The purpose of this communication is to report a new, easy, high-yield synthetic route to synthesize this compound in comfortable larger batches. Synthetic and isolation details, chemical characteristics, and the polymerizable properties of a new structurally related by-product monomer, namely, 2-(t-butyl),1-[4-(6-acryloxy-hexane-1-oxy)-benzoyloxy], 4-[4-[6-(3-acryl oxy-propionoxy)-hexane-1-oxy]-benzoyloxy]-benzene, is also reported. The structural confirmation of this by-product indicates that it resulted from the Michael-type addition of acrylate ion on one of the terminal acryloxy groups of 2-(t-butyl), 1,4-bis-[4-(6-acryloxy-hexane-1-oxy)-benzoyloxy] benzene. The by-product itself, as well as the natural blend of the aforesaid both products as formed in the reaction mixture, also polymerized at room temperature with lesser volume shrinkage as compared to the conventional control (GTE) at similar degrees of conversion.