Evaluation of auramine genotoxicity in primary rat and human hepatocytes and in the intact rat

Auramine O UV Photocatalytic Degradation on TiO2 Nanoparticles in a Heterogeneous Aqueous Solution

Amongst the environmental issues throughout the world, organic synthetic dyes continue to be one of the most important subjects in wastewater remediation. In this paper, the photocatalytic degradation of the dimethylmethane fluorescent dye, Auramine O (AO), was investigated in a heterogeneous aqueous solution with 100 nm anatase TiO2 nanoparticles (NPs) under 365 nm light irradiation. The effect of irradiation time was systematically studied, and photolysis and adsorption of AO on TiO2 NPs were also evaluated using the same experimental conditions. The kinetics of AO photocatalytic degradation were pseudo-first order, according to the Langmuir–Hinshelwood model, with a rate constant of 0.048 ± 0.002 min−1. A maximum photocatalytic efficiency, as high as 96.2 ± 0.9%, was achieved from a colloidal mixture of 20 mL (17.78 μmol L−3) AO solution in the presence of 5 mg of TiO2 NPs. The efficiency of AO photocatalysis decreased nonlinearly with the initial concentration and catalyst dosage. Based on the effect of temperature, the activation energy of AO photocatalytic degradation was estimated to be 4.63 kJ mol−1. The effect of pH, additional scavengers, and H2O2 on the photocatalytic degradation of AO was assessed. No photocatalytic degradation products of AO were observed using UV–visible and Fourier transform infrared spectroscopy, confirming that the final products are volatile small molecules.

Hybrid of sodium polytungstate polyoxometalate supported by the green substrate for photocatalytic degradation of auramine-O dye

Nowadays, textile industries have severely polluted the ecosystem and water sources via disposal of highly thermo- and photo-stable dyes within the ecology that require practical strategies to remove them from nature. In studies, the photocatalytic disinfection technique has been shown to have widespread applications in indoor air, environmental health, detection, biological, biomedical, laboratory hospital, pharmaceutical food industry, plant safety, waste water, effluents disposal, and drinking water disinfection. Herein, the sodium polytungstate (SPT) polyoxometalate (POM) was synthesized through a multi-step production procedure and hence modified via employing a green protocol by using tartaric acid, glutamic acid, and kombucha solvent toward efficient and total complete removal of the highly toxic, stable, and carcinogenic auramine-O (AO) dye from aqueous media. In this regard, developed materials were well-characterized, and their photocatalysis performance for photodegradation of AO dye was examined. Achieved results showed that the optimum absorption conditions were achieved at pH of 5.0, 15 mg/L of AO concentration, 0.04 g of photocatalyst dosage, and 110 min irradiation time, where SPT and modified SPT via green protocol showed full desirability (desirability function (DF) index of 1) along with 71.75 and 100% removal percentage, respectively. Obtained results justified the superior photocatalytic role of the SPT POM and its derived nanocluster that can be used for the complete removal of highly stable dyes from aqueous media till reaching the drinking water standard.

Effective Multi Toxic Dyes Degradation Using Bio-Fabricated Silver Nanoparticles as a Green Catalyst

Herein, we reported the preparation and characterization of silver nanoparticles from Kalanchoe brasiliensis leaves extract and their application in the photocatalytic degradation of Aniline Blue, Toludine Blue, Congo Red, Indigo Carmine, Auramine O, and Pyronin Y dyes. The synthesis of Kalanchoe brasiliensis extract derived silver nanoparticles (KK-AgNPs) was well characterized by several techniques. The surface plasma resonance (SPR) peak of 17 nm sized KK-AgNPs occurred at 445 nm, and the KK-AgNPs were stable for more than five months. Finally, KK-AgNPs were used as a green catalyst for the photocatalytic degradation of the above-mentioned dyes. Interestingly, the KK-AgNPs green catalyst decolorized all six dyes and their mixture. We found high catalytic efficiency up to 86%. Moreover, we used the KK-AgNPs green catalyst to degrade industrial dye effluent water. We also discussed the possible mechanism for the photocatalytic degradation of dyes.

Auramine dyes induce toxic effects to aquatic organisms from different trophic levels: an application of predicted non-effect concentration (PNEC)

The dyes Auramine and Auramine O are used in several industrial products, despite the scarce information regarding their ecotoxicity. The aim of the present study was to assess the acute and chronic toxicity of both dyes to aquatic organisms from different trophic levels (Raphidocelis subcapitata, Daphnia similis, Hydra attenuata, and Danio rerio) and calculate their predicted non-effect concentrations (PNEC). Auramine and Auramine O induced toxicity to all selected test organisms with L(E)C50 values ranging from 300 to 4800 ug/L. Both dyes induced inhibition in the growth rate of exposed algae, negatively affecting the reproduction of D. similis and induced deformities in H. attenuata (clubbed tentacles and shortened tentacles) and D. rerio (edemas, tail malformation and delay in yolk sac absorption). PNEC values of 0.92 μg/L and 4.0 μg/L were obtained for Auramine and Auramine O, respectively, based on results of the most sensitive test system (algae). Test results were analyzed using the Criteria of Reporting and Evaluating Ecotoxicity Data (CRED), confirming their reliability and relevance. Thus, PNEC values can be used in future risk assessments of those substances in freshwater systems.

Genetic toxicity assessment using liver cell models: past, present, and future

Genotoxic compounds may be detoxified to non-genotoxic metabolites while many pro-carcinogens require metabolic activation to exert their genotoxicity in vivo. Standard genotoxicity assays were developed and utilized for risk assessment for over 40 years. Most of these assays are conducted in metabolically incompetent rodent or human cell lines. Deficient in normal metabolism and relying on exogenous metabolic activation systems, the current in vitro genotoxicity assays often have yielded high false positive rates, which trigger unnecessary and costly in vivo studies. Metabolically active cells such as hepatocytes have been recognized as a promising cell model in predicting genotoxicity of carcinogens in vivo. In recent years, significant advances in tissue culture and biological technologies provided new opportunities for using hepatocytes in genetic toxicology. This review encompasses published studies (both in vitro and in vivo) using hepatocytes for genotoxicity assessment. Findings from both standard and newly developed genotoxicity assays are summarized. Various liver cell models used for genotoxicity assessment are described, including the potential application of advanced liver cell models such as 3D spheroids, organoids, and engineered hepatocytes. An integrated strategy, that includes the use of human-based cells with enhanced biological relevance and throughput, and applying the quantitative analysis of data, may provide an approach for future genotoxicity risk assessment.

Adsorptive Removal of Recalcitrant Auramine-O Dye by Sodium Dodecyl Sulfate Functionalized Magnetite Nanoparticles: Isotherm, Kinetics, and Fixed-Bed Column Studies

Presently, the treatment of dye-polluted water is a challenging task worldwide. In this study, the adsorptive removal of Auramine-O (AO) dye by magnetite nanoparticles (MNs) and sodium dodecyl sulfate (SDS) functionalized MNs (SFMNs) were investigated. FESEM, HRTEM, EDX, and XRD were employed to characterize the MNs. In batch optimization, dye removal efficiency of 74% was obtained at contact time (40[Formula: see text]min), pH 6.5, sorbent dosage (20[Formula: see text]mg), and initial dye concentration (20[Formula: see text]mg/L). The maximum adsorption capacity of 55.56[Formula: see text]mg/g was estimated from Langmuir model and the isotherm data were fitted with Freundlich model ([Formula: see text]) for SFMNs. Pseudo-second-order kinetics was followed by both MNs and SFMNs for the adsorption of AO dye. The continuous AO dye adsorption was studied in fixed-bed column and the effects of bed height, influent flow rate, and initial dye concentration were investigated. The column performance was evaluated by breakthrough kinetic modeling and Yoon–Nelson model was fitted with the data. The results of this study showed that the surface modification of MNs using SDS enhanced the AO dye removal efficiency and SFMNs can be employed as an efficient nanoadsorbent for AO dye removal in batch and continuous mode of operation.

Auramine O, an incense smoke ingredient, promotes lung cancer malignancy

Burning incense to worship deities is a popular religious ritual in large parts of Asia, and is a popular custom affecting more than 1.5 billion adherents. Due to incomplete combustion, burning incense has been well recognized to generate airborne hazards to human health. However, the correlation between burning incense and lung cancer in epidemiological studies remains controversy. Therefore, we speculated that some unknown materials in incense smoke are involved in the initiation or progression of lung cancer. Based on this hypothesis, we identified a major compound auramine O (AuO) from the water-soluble fraction of incense burned condensate using mass spectrometry. AuO is commonly used in incense manufacture as a colorant. Due to thermostable, AuO released from burned incenses becomes an unexpected air pollutant. AuO is classified as a Group 2B chemical by the International Agency of Research on Cancer (IARC), however, the damage of AuO to the respiratory system remains elusive. Our study revealed that AuO has no apparent effect on malignant transformation; but, it dramatically promotes lung cancer malignancy. AuO accumulates in the nucleus and induces the autophagy activity in lung tumor cells. AuO significantly enhances migration and invasive abilities and the in vitro and in vivo stemness features of lung tumor cells through activating the expression of aldehyde dehydrogenase family 1 member A1 (ALDH1A1), and ALDH1A1 knockdown attenuates AuO-induced autophagy activity and blocks AuO-induced lung tumor malignancy. In conclusion, we found that AuO, an ingredient of incense smoke, significantly increases the metastatic abilities and stemness characters of lung tumor cells through the activation of ALDH1A1, which is known to be associated with poor outcome and progression of lung cancer. For public health, reducing or avoiding the use of AuO in incense is recommended.

Sequestration of dyes from artificially prepared textile effluent using RSM-CCD optimized hybrid backbone based adsorbent-kinetic and equilibrium studies

Present work reports the synthesis of semi-Interpenetrating Network Polymer (semi-IPN) using Gelatin-Gum xanthan hybrid backbone and polyvinyl alcohol in presence of l-tartaric acid and ammonium persulphate as the crosslinker-initiator system. Reaction parameters were optimized with Response Surface Methodology (RSM) in order to maximize the percent gel fraction of the synthesized sample. Polyvinyl alcohol, l-Tartaric acid, ammonium persulphate, reaction temperature, time and pH of the reaction medium were found to make an impact on the percentage gel fraction obtained. Incorporation of polyvinyl alcohol chains onto hybrid backbone and crosslinking between the different polymer chains were confirmed through techniques like FTIR, SEM-EDX and XRD. Semi-IPN was found to be very efficient in the removal of cationic dyes rhodamine-B (70%) and auramine-O (63%) from a mixture with an adsorbent dose of 700 mg, initial concentration of rhodamine-B 6 mgL^-1 and auramine-O 26 mgL^-1, at an time interval of 22-25 h and 30 °C temp. Further to determine the nature of adsorption Langmuir and Freundlich adsorption isotherm models were studied and it was found that Langmuir adsorption isotherm was the best fit model for the removal of mixture of dyes. Kinetic studies for the sorption of dyes favored the reaction mechanism to occur via a pseudo second order pathway with R² value about 0.99.

Surface response methodology–central composite design screening for the fabrication of a Gx-psy-g-polyacrylicacid adsorbent and sequestration of auramine-O dye from a textile effluent

The present work reported the gum xanthan–psyllium based semi-IPN which was used for the efficient capture of auramine-O dye from aqueous fluid.

Simultaneous ultrasound-assisted ternary adsorption of dyes onto copper-doped zinc sulfide nanoparticles loaded on activated carbon: optimization by response surface methodology

The simultaneous and competitive ultrasound-assisted removal of Auramine-O (AO), Erythrosine (Er) and Methylene Blue (MB) from aqueous solutions were rapidly performed onto copper-doped zinc sulfide nanoparticles loaded on activated carbon (ZnS:Cu-NP-AC). ZnS:Cu nanoparticles were studied by FESEM, XRD and TEM. First, the effect of pH was optimized in a one-at-a-time procedure. Then the dependency of dyes removal percentage in their ternary solution on the level and magnitude of variables such as sonication time, initial dyes concentrations and adsorbent dosage was fully investigated and optimized by central composite design (CCD) under response surface methodology (RSM) as well as by regarding desirability function (DF) as a good and general criterion. The good agreement found between experimental and predicted values supports and confirms the suitability of the present model to predict adsorption state. The applied ultrasound strongly enhanced mass transfer process and subsequently performance. Hence, a small amount of the adsorbent (0.04 g) was capable to remove high percentage of dyes, i.e. 100%, 99.6% and 100% for MB, AO and Er, respectively, in very short time (2.5 min). The experimental equilibrium data fitting to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models showed that the Langmuir model applies well for the evaluation and description of the actual behavior of adsorption. The small amount of proposed adsorbent (0.015 g) was applicable for successful removal of dyes (RE>99.0%) in short time (2.5 min) with high adsorption capacity in single component system (123.5 mg g(-1) for MB, 123 mg g(-1) for AO and 84.5 mg g(-1) for Er). Kinetics evaluation of experiments at various time intervals reveals that adsorption processes can be well predicated and fitted by pseudo-second-order and Elovich models.

Application of ultrasonic radiation for simultaneous removal of auramine O and safranine O by copper sulfide nanoparticles: experimental design

In this study, copper sulfide nanoparticles loaded on activated carbon (CuS-NP-AC) were synthesized by novel, low cost and green approach and characterized using SEM and XRD. The application of this material for the simulations removal of auramine O (AO) and safranine O (SO) from aqueous solutions was investigated. The dependency of removal percentages to variables such as pH, initial dyes concentration, adsorbent dosage, sonication time and sonication temperature were studied with response surface methodology (RSM) by considering the desirability function (DF). The quadratic model between the dependent and the independent variables was built. The proposed method showed good agreement between the experimental data and predictive value, and it has been successfully employed to removal of AO and SO in aqueous media. The studied adsorbent (0.06 g of CuS-NP-AC) was capable of high percentage removal (99.8% and 99.5%) of 18 mg mL(-1) AO and SO in short time (7.0 min).

Removal of basic dye Auramine-O by ZnS:Cu nanoparticles loaded on activated carbon: optimization of parameters using response surface methodology with central composite design

FESEM images of the prepared ZnS:Cu-NPs-AC.

Adsorptive removal of Auramine-O: kinetic and equilibrium study

Present study deals with the adsorption of Auramine-O (AO) dye by bagasse fly ash (BFA) and activated carbon-commercial grade (ACC) and laboratory grade (ACL). BFA is a solid waste obtained from the particulate collection equipment attached to the flue gas line of the bagasse fired boilers of cane sugar mills. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH(0)), contact time, adsorbent dose and initial concentration (C(0)) for the removal of AO. Optimum conditions for AO removal were found to be pH(0) approximately 7.0 and equilibrium time approximately 30 min for BFA and approximately 120 min for activated carbons. Optimum BFA, ACC and ACL dosages were found to be 1, 20 and 2g/l, respectively. Adsorption of AO followed pseudo-second order kinetics with the initial sorption rate for adsorption on BFA being the highest followed by those on ACL and ACC. The sorption process was found to be controlled by both film and pore diffusion with film diffusion at the earlier stages followed by pore diffusion at the later stages. Equilibrium isotherms for the adsorption of AO on BFA, ACC and ACL were analyzed by Freundlich, Langmuir, Dubinin-Radushkevich, and Temkin isotherm equations using linear correlation coefficient. Langmuir isotherm gave the best correlation of adsorption for all the adsorbents studied. Thermodynamic study showed that adsorption of AO on ACC (with a more negative Gibbs free energy value) is more favoured. BFA which was used without any pretreatment showed high surface area, pore volume and pore size exhibiting its potential to be used as an adsorbent for the removal of AO.

Putative identification of functional interactions between DNA intercalating agents and topoisomerase II using the V79 in vitro micronucleus assay

Clastogenicity is frequently observed following treatment of mammalian cells with new chemical entities. This clastogenicity, unless proven otherwise, is assumed to result from the imperfect repair of DNA lesions produced from covalent chemical/DNA interaction. However, clastogenicity can also arise via other mechanisms such as non-covalent chemical intercalation into DNA resulting in poisoning of cellular DNA topoisomerase II (topo II) and stabilization of DNA double strand breaks. We have recently reported modifications to the V79 in vitro micronucleus assay which allow an indirect evaluation of both the intercalative and topoisomerase-interactive activities of chemical agents. In the present studies we have used these modified assays to further assess the validity of this approach in an evaluation of a number of intercalating and non-intercalating polycyclic compounds. It is shown that intercalating agents may be catalytic topo II inhibitors (e.g. chloroquine (CHL), tacrine (TAC), 9-aminoacridine (9AA), ethidium bromide (EB)) or topo II poisons (e.g. proflavine (PROF), auramine O (AUR) and curcumin (CURC)). Still other intercalators are shown to lack detectable topo II-interactions, (e.g. imipramine (IMP), quinacrine (QUIN), 2-aminoanthracene (AA), iminostilbene (IMN) and promethazine (PHE)). It is concluded that (1) the clastogenicity of three agents, PROF (a typical DNA intercalating agent), and AUR and CURC (both structurally atypical intercalating agents, with unknown clastogenic mechanisms), may be due to topo II poisoning; (2) other intercalating agents may either act as catalytic topo II inhibitors or exhibit no functional topo II interaction; (3) The use of these cell-based approaches may provide a logical first step in determining if unexpected clastogenicity associated with test article exposure is due to a topo II interaction.

Comparative in vitro and in vivo assessment of genotoxic effects of etoposide and chlorothalonil by the comet assay

The alkaline single cell gel electrophoresis (comet) assay was used to assess in vitro and in vivo genotoxicity of etoposide, a topoisomerase II inhibitor known to induce DNA strand breaks, and chlorothalonil, a fungicide widely used in agriculture. For in vivo studies, rats were sacrificed at various times after treatment and the induction of DNA strand breaks was assessed in whole blood, bone marrow, thymus, liver, kidney cortex and in the distal part of the intestine. One hour after injection, etoposide induced DNA damage in all organs studied except kidney, especially in bone marrow, thymus (presence of HDC) and whole blood. As observed during in vitro comet assay on Chinese hamster ovary (CHO) cells, dose- and time-dependent DNA effects occurred in vivo with a complete disappearance of damage 24 h after administration. Even though apoptotic cells were detected in vitro 48 h after cell exposure to etoposide, such a result was not found in vivo. After chlorothalonil treatment, no DNA strand breaks were observed in rat organs whereas a clear dose-related DNA damage was observed in vitro. The discrepancy between in vivo and in vitro models could be explained by metabolic and mechanistic reasons. Our results show that the in vivo comet assay is able to detect the target organs of etoposide and suggest that chlorothalonil is devoid of appreciable in vivo genotoxic activity under the protocol used.