Systematic Study of Microplastic Fiber Release from 12 Different Polyester Textiles during Washing

Severe microplastic pollution risks in urban freshwater system post-landfill fire: A case study from Brahmapuram, India

To investigate the escalating issue of microplastic (MP), pollution in urban water bodies, this study focuses on the aftermath of the Brahmapuram landfill fire in Kochi, India, analyzing its impact on MP concentrations in nearby freshwater system. The study conducted sampling sessions at the landfill site immediately before and after the fire. Post-fire, findings demonstrated a substantial increase in MP concentrations in surface waters, with levels rising from an average 25793.33 to 44863.33 particles/m³, featuring a notable presence of larger, predominantly black MPs. Sediment samples showed no significant change in MP count, but there was a significant increase in mass concentration. SEM/EDS analysis revealed changes in surface morphology and elemental composition, suggesting thermal degradation. Risk assessment using the Microplastic Pollution Index (MPI) and Risk Quotient (RQ) methods indicated heightened MP pollution risk in surface water post-fire. Hierarchical cluster analysis revealed the landfill's proximity as a significant factor influencing MP characteristics in the aquatic system. The study highlights the escalated challenge of MP pollution in urban water bodies following environmental disasters like landfill fires, underscoring the urgent need for policy and environmental management strategies.

Understanding microplastic presence in different wastewater treatment processes: Removal efficiency and source identification

Municipal effluents discharged from wastewater treatment plants (WWTPs) are a considerable source of microplastics in the environment. The dynamic profiles of microplastics in treatment units in WWTPs with different treatment processes remain unclear. This study quantitatively analyzed microplastics in wastewater samples collected from different treatment units in two tertiary treatment plants with distinct processes. The influents contained an average of 15.5 ± 3.5 particles/L and 38.5 ± 2.5 particles/L in the two WWTPs with in the oxidation ditch process and the integrated fixed-film activated sludge process, respectively. Interestingly, microplastic concentrations in the influent were more influenced by the population density in the served area than sewage volume or served population equivalent. Throughout the treatment process, concentrations were reduced to 1.5 ± 0.5 particles/L and 1.0 ± 1.0 particles/L in the final effluents, representing an overall decrease of 90% and 97%, in WWTPs with the oxidation ditch process and integrated fixed-film activated sludge process, respectively. A significant proportion of the microplastics were removed during the primary treatment stage in both WWTPs, with better performance for foam, film, line-shaped and large-sized microplastics. Most microplastics were accumulated in activated sludge, indicating its key role as the primary sink in WWTPs. The multiple correspondence analysis identified laundry washing and daily necessities such as packaging and containers as the major contributors to microplastics in WWTPs. The study proposed recommendations for upgrading WWTPs, modifying designs, and implementing strategies to reduce microplastic sources, aiming to minimize the release of microplastics into the environment. These findings can shed lights on the sources of microplastics in WWTPs, and advance our understanding of the mechanisms for more effective microplastic removals in wastewater treatment technologies in future applications.

Microplastic pollution responses to spatial and seasonal variations and water level management in a polymictic tropical reservoir (São Paulo, Brazil)

We assessed microplastic (μP) pollution in water and sediment samples during the dry and rainy season (October/2018 and March/2019, respectively) from the Guarapiranga Reservoir in the Metropolitan Region of São Paulo, Brazil, which provides drinking water for up to 5.2 million people. The concentration of mPs varied spatially and seasonally, with the higher concentrations observed near the urbanized areas and during the dry season. Water column concentrations ranged from 150 to 3100 particles/m3 and 0.07-25.05 mm3 plastic/m3 water during the dry season, and 70-7900 particles/m3 and 0.06-4.57 mm3 plastic/m3 water during the rainy season. Sediment samples were collected only during the rainy season, with concentrations ranging from 210 to 22,999 particles/kg dry weight and 0.15-111.46 mm3/kg dry weight. The particle size distribution exhibited seasonal variation, with μPs >1 mm predominating during the dry season, constituting 60-75% of all particles. In terms of quantity, fibers accounted for the majority of microplastics, comprising 55-95% during the dry season and 70-92% during the rainy season. However, when considering particle volume, irregular particles dominated in some samples, accounting for up to 95% of the total amount. The predominant colors of microplastics were white/crystal, black, and blue, with the main compositions identified as polypropylene (PP) and polyethylene terephthalate (PET), suggesting the influence of untreated domestic sewage discharge. Additionally, some additives were detected, including the pigments Fast RED ITR and phthalocyanine blue. The management of reservoir water levels appears to influence the quantity of μPs in the water column. As the water level increases up to 90% of the reservoir capacity during the rainy season, the amount of μPs in the water decreases, despite the higher influx of particles resulting from surface runoff caused by rainy conditions. This suggests a "dilution" effect combined to the polymictic mixing hydrodynamics. Our results may contribute to the creation and improvement of monitoring programs regarding mP pollution and to the adoption of specific public policies, which are still lacking in legislation.

Suspension of micro- and nanoplastic test materials: liquid compatibility, (bio)surfactants, toxicity and environmental relevance

Micro- and nanoplastics have been detected in environmental compartments from the highest mountains to the deepest seas. They have been shown to be present at almost all trophic levels, and within humans they have been detected in numerous organs and human stool. Whilst their ubiquitous nature is indisputable, little is known about the health risks they may present. Much current research is focussed on the production of test materials with which to perform the necessary health studies. An important aspect of this is the correct storage and suspension of the materials to ensure they remain stable both chemically and with regards to size and shape. In this review, we look at the chemical stability of nine common polymers in a range of liquids; first with the use of commercial compatibility charts and then with a more quantitative approach using Hansen solubility parameters. We then look at stability with regards to particle agglomeration, whether and how stable compositions can be predicted, and which dispersants can be added to increase stability. Finally, we discuss the role of bio-surfactants and the eco-corona and how these may offer a route to both better stability and environmental relevance.

Internal water circulation mediated synergistic co-hydrolysis of PET/cotton textile blends in gamma-valerolactone

Recycling strategies for mixed plastics and textile blends currently aim for recycling only one of the components. Here, we demonstrate a water coupling strategy to co-hydrolyze polyester/cotton textile blends into polymer monomers and platform chemicals in gamma-valerolactone. The blends display a proclivity for achieving an augmented 5-hydroxymethylfurfural yield relative to the degradation of cotton alone. Controlled experiments and preliminary mechanistic studies underscore that the primary driver behind this heightened conversion rate lies in the internal water circulation. The swelling and dissolving effect of gamma-valerolactone on polyester enables a fast hydrolysis of polyester at much lower concentration of acid than the one in the traditional hydrolysis methods, effectively mitigating the excessive degradation of cotton-derived product and undesirable product formation. In addition, the system is also applicable to different kinds of blends and PET mixed plastics. This strategy develops an attractive path for managing end-of-life textiles in a sustainable and efficient way.

Microplastic generation from field-collected plastic gauze: Unveiling the aging processes

Accumulation of plastic debris in the environment is a matter of global concern. As plastic ages, it generates microplastic (MP) particles with high mobility. Understanding how MPs are generated is crucial to controlling this emerging contaminant. In this study, we utilized high-density polyethylene (HDPE) plastic gauze, collected from urban settings, as a representative example of plastic waste. The plastic gauze was subjected to various aging conditions, including freeze-thaw cycling, mechanical abrasion, and UV irradiation. Following aging, the plastic gauze was rinsed with water, and the number of generated MPs were quantified. It was found that aged plastic gauze generated up to 334 million MP particles per m2 (> 10 µm) during rinsing, a number two orders of magnitude higher than unaged plastic. Fragmentation occurred in two dimensions for bulk MPs of all morphotypes. However, specific aging approaches (i.e., mechanical abrasion and UV irradiation) generated spheres and fibers via pseudo-3D fragmentation. Additionally, changes in molecular weight, size distribution, and surface oxidation characteristics unveiled a complex pattern (i.e., irregular changes with exposure time). This complexity underscores the intricate nature of plastic debris aging processes in the environment.

Microfluidic Detection and Analysis of Microplastics Using Surface Nanodroplets

Detection of microplastics from water is crucial for various reasons, such as food safety monitoring, monitoring of the fate and transport of microplastics, and development of preventive measures for their occurrence. Currently, microplastics are detected by isolating them using filtration, separation by centrifugation, or membrane filtration, subsequently followed by analysis using well-established analytical methods, such as Raman spectroscopy. However, due to their variability in shape, color, size, and density, isolation using the conventional methods mentioned above is cumbersome and time-consuming. In this work, we show a surface-nanodroplet-decorated microfluidic device for isolation and analysis of small microplastics (diameter of 10 μm) from water. Surface nanodroplets are able to capture nearby microplastics as water flows through the microfluidic device. Using a model microplastic solution, we show that microplastics of various sizes and types can be captured and visualized by using optical and fluorescence microscopy. More importantly, as the surface nanodroplets are pinned on the microfluidic channel, the captured microplastics can also be analyzed using a Raman spectroscope, which enables both physical (i.e., size and shape) and chemical (i.e., type) characterization of microplastics at a single-particle level. The technique shown here can be used as a simple, fast, and economical detection method for small microplastics.

A case study on microplastics pollution characteristics in fouling organisms in typical aquaculture bay, China

Microplastics (MPs) and fouling organisms are prevalent in oceans worldwide. The study aims to investigate the pollution characteristics of MPs in fouling organisms. The study found significant inter-specific differences in the MPs abundance, while the length of MPs is consistent. The average number of MPs in N. exigua is 0.00 ± 0.00. There is a correlation between MPs abundance and weight in sessile group, while gastropods don't. Direct observation has demonstrated that the radulae of N. radula can envelop MPs. Fiber and blue are the predominant forms and colors of MPs found in fouling organisms. It is noteworthy that all film and fragment MPs observed were of a blue hue and had a size limitation of 500 μm. The characteristics of MPs between sessile organisms are more similar than those between gastropods. This study has improved our understanding of the pollution characteristics of MPs in fouling organisms, specifically gastropods.

Characterization and traceability analysis of dry deposition of atmospheric microplastics (MPs) in Wuliangsuhai Lake

Microplastics (MPs) represent a contaminant of emerging concern that may negatively impact lacustrine ecosystems. It is important, then, to manage and reduce the influx of MPs to lakes, a process that requires the identification of MP sources. In this study, atmospheric MP samples were collected and analyzed from 6 sampling sites in the Wuliangsuhai Lake area from March to June 2021, and used to determine atmospheric depositional fluxes of MPs to the lake surface. The sources of MPs were also explored on the basis of MP characteristics and by determining atmospheric flow patterns to the sampling sites using a backward trajectory model (HYSPLIT). The average atmospheric depositional flux of MPs to the Wuliangsuhai Lake area (3371 ± 1423 n/d·m2) is several times higher than rates measured in other areas. MPs were predominately composed of small (0.05-0.5 mm), transparent fibers; a small percentage of particles consisted of fragments, thin films, or lumpy MPs. Compositionally, most MPs were composed of polyethylene (PE), polyethylene terephthalate (PET), and polystyrene (PS). The former polymer types are indicative of fibers from textiles, including those from textile plants in adjacent cites. The latter (PS) type is presumably derived from degraded food containers and other items associated with tourism. PE was also identified in association with thin films, which were likely derived from bags and/or agricultural plastics. MP characteristics, combined with spatial variations in depositional rates and the results of the backward trajectory model, suggest most atmospherically deposited MPs in the Wuliangsuhai Lake area were transported to the sampling sites from large cities external to the basin, and, to a much lesser degree, areas of tourism within the lake environment. The results of the study provide a theoretical basis for assessing atmospheric MP deposition within inland lake areas as well as for the prevention and control of MP pollution.

Study on the simultaneous release of microfiber and indigo dye in denim fabric home washing

In recent years, with the increasing global focus on environmental protection, the issue of microfiber release from denim during the washing process has gained attention. In this study, a programmable washing device simulating household drum washing was designed and developed, microfibers and indigo dyes released from denim washing were quantitatively detected, and we have also developed a novel method for estimating the release of microfibers during washing. The effects of washing time, washing temperature, and washing load on microfiber and indigo dye release from denim were explored. The results showed that the effect of washing load on microfiber and indigo dye release was greater than washing temperature and washing time. The research findings indicate that with an increase in washing time (35-95 min) and washing load (100-250 g), the shedding of microfibers and indigo dye significantly increases, reaching peak release levels of 343.6 μg/g fabric and 0.027 mg/L, respectively. However, there is a decreasing trend in the release of microfibers and indigo dye when the washing temperature exceeds 50 °C. Furthermore, our data suggests that an increase in washing load leads to a significant change in the number of microfibers (from 978 items/g fabric to 1997 items/g fabric) and their mass (from 156.87 μg/g fabric to 343.56 μg/g fabric). The influence of washing time, washing temperature, and washing load on microfiber length shows relatively small fluctuations within the range of 600-900 µm. This study provides new ideas and methods for estimating the release of microfiber and indigo dye in denim washing around the world.

Impact of sewing on microfiber release from polyester fabric during laundry

Microfibers released from textile materials are receiving greater attention due to their severe adverse effects on the environment. Although mitigation strategies have been developed for laundering, researchers uphold that it is crucial to start mitigating at the source. In that aspect, this research aims to analyze the cutting and sewing methods of knitted fabrics and their impact on the microfiber release of garments during laundry. The results of the study have confirmed that cutting and sewing methods have a significant impact on the microfiber release of a garment. The analysis of different cutting methods showed that laser and ultrasonic cutting methods reduce the microfiber release up to 20 times compared to the conventional scissor-cut edges. While comparing the different stitch types, the overlock stitch type showed reduced shedding than the other stitch types (flatlock stitch and single needle lockstitch). Our results also showed that the use of more needles increases the microfiber emission among different stitch variations of the same stitch type. For instance, a 45.27 % increase in microfiber emission was reported with the 4-thread overlock stitch (2 needles) than with the 3-thread stitch (1 needle). Regarding seam type, the proposed edge finishing seam (EFb) was effective in reducing 93 % of microfiber release as the edges are completely covered. When the effect of stitch density is considered, in the case of single needle lockstitch and flatlock stitch, the microfiber release is reduced with increased stitch density. However, a different trend was noted in the overlock stitch, which needed detailed exploration in the future. The results confirmed that a proper selection of stitch, stitch density, and seam type would reduce the microfiber release from a garment by up to 64.6 %.

Microplastics in the seagrass ecosystems: A critical review

Marine microplastic (MP) pollution represents a global environmental issue that has ignited considerable apprehension within the international community. Seagrass beds, which serve as nearshore marine ecosystems, have emerged as focal points of plastic and MP contamination due to the pronounced density of anthropogenic activities and the hydrological mitigating effects of submerged vegetation. Nevertheless, our comprehension of MPs within seagrass ecosystems remains constrained. In this study, we employed bibliometric analyses and comprehensive data exploration to summarize the historical progression of the development, pivotal areas of interest, and research deficiencies, followed by proposing future research directions for MP pollution in seagrass beds. The 37 selected papers were sourced from the Web of Science Core Collection scientific database as of December 31st, 2022. Based on the current evaluation, MPs are ubiquitously discovered within seagrass canopies, sediments, and marine organisms, while less than 15 % of seagrass species worldwide have been investigated. Moreover, methodological inconsistencies in sampling, processing and visualization between studies hindered the fusion and comparison of data. MPs in upper sediments and seagrass blades were the most widely investigated, with an average abundance of 263.4 ± 309.2 n/kg and 0.09 ± 0.03 n/blade. In all environmental compartments, the prevalent forms of MPs comprise fibrous and fragmented particles, encompassing the dominant polymers such as polypropylene, polyethylene and polyethylene terephthalate. However, the source of MPs in seagrass beds based on MP characteristics and local hydrodynamics has not been comprehensively analyzed in previous studies. The evidence for MPs acting as pollutants and contaminant carries impacting the growth and decline of seagrass is also weak. Currently, the precise implications of MPs on submerged vegetation, organisms, and the broader seagrass ecosystem remain inconclusive. However, considering the persistent accumulation of MPs, it is imperative to explore the ecological hazards they may pose within the foreseeable future.

Impact of quantification method on microfiber assessment - A comparative analysis between mass and count based methods

Microfiber from textiles is one of the new anthropogenic pollutants which attracted a wide range of researchers. Domestic laundry, being the most common cause of microfiber release from textiles, is widely studied. Studies exhibit a broad range of quantities of microfibers owing to the distinct quantification methodologies employed due to their convenience and resource availability. Out of several such estimation processes, reporting microfiber quantity in numbers or mass (mg or g) is quite common with respect to the unit area or weight of the textile used. However, results reported by different literature vary significantly. Hence, this study aims to analyze the microfiber release from knitted polyester fabric using count- and mass-based methods. Four different fabrics were used for this study with three different counting processes from literature along with direct weight difference estimation. The results of the direct counting method showed that the average microfiber release of selected fabrics is 13.28-33.16 microfibers per sq.cm, whereas, the direct weight estimation showed an average weight of 0.0664 ± 0.0289 mg/sq.cm. The subsequent conversion showed a release of 887.89 ± 633.49 microfibers/sq.cm of the fabric. Further, the microfiber mass was also estimated using the number of microfiber count and found that a sq.cm of fabric releases up to 0.0010-0.0024 mg of microfibers. While comparing the results, the weight-based estimation showed a significantly higher microfiber release (41.3-42.9 times) than the direct counting method. The deposition of surfactants in detergents, contaminants from the water, atmospheric contaminants, and finishes released from the fabric can be the sources of additional weights noted in the direct mass estimation. As the weight-based method is quite simple and the fastest way to quantify the microfibers, future studies must focus on this area to reduce the error percentage in quantification.

Investigation of ring, airjet and rotor spun yarn structures on the fragmented fibers (microplastics) released from polyester textiles during laundering

The release of fragmented fibers (FFs), including microplastics from textiles, during their service life is considered an established source of environmental pollution. The yarn structure is identified to affect the amount and length distribution profile of shed FFs from textiles. In the present work, the impact of yarn structures spun from 100% polyester staple fibers, using commercially relevant spun yarn technologies in the textile industry, on the release of FFs from textiles is studied. The bespoke woven fabric samples produced from three types of spun yarns, which include ring, airjet (air vortex) and rotor yarns, were subjected to an accelerated washing process, for up to five washes, to quantify shed FFs and their length distribution profile. The morphological shapes of FF ends associated with the nature of fiber damage were also investigated. The results demonstrated that airjet and rotor yarn structures had released 28% and 33% less mass of FFs, respectively, as compared to the ring yarn structure during the whole washing process. The length distribution profile identified that the ring yarn structure shed longer length FFs as compared to both airjet and rotor ones. The damaged ends highlight the importance of textile manufacturing processes on the generation of FFs. The results of this study give a better understanding of the yarn structural effect of commercially relevant technologies on shedding of FFs, which are released as a pollutant to the environment.

Interaction between antibiotics and microplastics: Recent advances and perspective

Both microplastics and antibiotics are emerging pollutants, which are ubiquitous in aquatic environments. With small size, high specific surface area, and attached biofilm, microplastics are capable of adsorbing or biodegrading antibiotic pollutants across aquatic environments. However, the interactions between them are poorly understood, especially factors that affect microplastics' chemical vector effects and the mechanisms driving these interactions. In this review, the properties of microplastics and their interaction behavior and mechanisms towards antibiotics were comprehensively summarized. Particularly, the impact of weathering properties of microplastics and the growth of attached biofilm was highlighted. We concluded that compared with virgin microplastics, aged microplastics usually adsorb more types and quantities of antibiotics from aquatic environments, whilst the attached biofilm could further enhance the adsorption capacities and biodegrade some antibiotics. This review can answer the knowledge gaps of the interaction between microplastics and antibiotics (or other pollutants), offer basic information for evaluating their combined toxicity, provide insights into the distribution of both emerging pollutants in the global water chemical cycle, and inform measures to remove microplastic-antibiotic pollution.

Shapes of Hyperspectral Imaged Microplastics

Shape matters for microplastics, but its definition, particularly for hyperspectral imaged microplastics, remains ambiguous and inexplicit, leading to incomparability across data. Hyperspectral imaging is a common approach for quantification, yet no unambiguous microplastic shape classification exists. We conducted an expert-based survey and proposed a set of clear and concise shapes (fiber, rod, ellipse, oval, sphere, quadrilateral, triangle, free-form, and unidentifiable). The categories were validated on images of 11,042 microplastics from four environmental compartments (seven matrices: indoor air; wastewater influent, effluent, and sludge; marine water; stormwater; and stormwater pond sediments), by inviting five experts to score each shape. We found that the proposed shapes were well defined, representative, and distinguishable to the human eye, especially for fiber and sphere. Ellipse, oval, and rod were though less distinguishable but dominated in all water and solid matrices. Indoor air held more unidentifiable, an abstract shape that appeared mostly for particles below 30 μm. This study highlights the need for assessing the recognizability of chosen shape categories prior to reporting data. Shapes with a clear and stringent definition would increase comparability and reproducibility across data and promote harmonization in microplastic research.

Recent advances in biodegradation of emerging contaminants - microplastics (MPs): Feasibility, mechanism, and future prospects

Plastics have become an essential part of life. When it enters the environment, it migrates and breaks down to form smaller size fragments, which are called microplastics (MPs). Compared with plastics, MPs are detrimental to the environment and pose a severe threat to human health. Bioremediation is being recognized as the most environmentally friendly and cost-effective degradation technology for MPs, but knowledge about the biodegradation of MPs is limited. This review explores the various sources of MPs and their migration behavior in terrestrial and aquatic environments. Among the existing MPs removal technologies, biodegradation is considered to be the best removal strategy to alleviate MPs pollution. The biodegradation potential of MPs by bacteria, fungi and algae is discussed. Biodegradation mechanisms such as colonization, fragmentation, assimilation, and mineralization are presented. The effects of MPs characteristics, microbial activity, environmental factors and chemical reagents on biodegradation are analyzed. The susceptibility of microorganisms to MPs toxicity might lead to decreased degradation efficiency, which is also elaborated. The prospects and challenges of biodegradation technologies are discussed. Eliminating prospective bottlenecks is necessary to achieve large-scale bioremediation of MPs-polluted environment. This review provides a comprehensive summary of the biodegradability of MPs, which is crucial for the prudent management of plastic waste.

Photo-aging promotes the inhibitory effect of polystyrene microplastics on microbial reductive dechlorination of a polychlorinated biphenyl mixture (Aroclor 1260)

Polychlorinated biphenyls (PCBs) and microplastics (MPs) commonly co-exist in various environments. MPs inevitably start aging once they enter environment. In this study, the effect of photo-aged polystyrene MPs on microbial PCB dechlorination was investigated. After a UV aging treatment, the proportion of oxygen-containing groups in MPs increased. Photo-aging promoted the inhibitory effect of MPs on microbial reductive dechlorination of PCBs, mainly attributed to the inhibition of meta-chlorine removal. The inhibitory effects on hydrogenase and adenosine triphosphatase activity by MPs increased with increasing aging degree, which may be attributed to electron transfer chain inhibition. PERMANOVA showed significant differences in microbial community structure between culturing systems with and without MPs (p < 0.05). Co-occurrence network showed a simpler structure and higher proportion of negative correlation in the presence of MPs, especially for biofilms, resulting in increased potential for competition among bacteria. MP addition altered microbial community diversity, structure, interactions, and assembly processes, which was more deterministic in biofilms than in suspension cultures, especially regarding the bins of Dehalococcoides. This study sheds light on the microbial reductive dechlorination metabolisms and mechanisms where PCBs and MPs co-exist and provides theoretical guidance for in situ application of PCB bioremediation technology.

Recent analytical techniques, and potential eco-toxicological impacts of textile fibrous microplastics (FMPs) and associated contaminates: A review

Despite of our growing understanding of microplastic's implications, research on the effects of fibrous microplastic (FMPs) on the environment is still in its infancy. Some scientists have hypothesized the possibility of natural textile fibres, which may act as one of the emerging environmental pollutants prevalent among microplastic pollutants in the environment. Therefore, this review aims to critically evaluate the toxic effects of emerging FMPs, the presence, and sources of FMPs in the environment, identification and analytical techniques, and the potential impact or toxicity of the FMPs on the environment and human health. About175 publications (2011-2023) based on FMPs were identified and critically reviewed for transportation, analysis and ecotoxicological behaviours of FMPs in the environment. Textile industries, wastewater treatment plants, and household washing of clothes are significant sources of FMPs. In addition, various characterization techniques (e.g., FTIR, SEM, RAMAN, TGA, microscope, and X-Ray Fluorescence Spectroscopy) commonly used for the identification and analysis of FMPs are also discussed, which justifies the novelty aspects of this review. FMPs are pollutants of emerging concern due to their prevalence and persistence in the environment. FMPs are also found in the food chain, which is an alarming situation for living organisms, including effects on the nervous system, digestive system, circulatory system, and genetic alteration. This review will provide readers with a comparison of different analytical techniques, which will be helpful for researchers to select the appropriate analytical techniques for their study and enhance their knowledge about the harmful effects of FMPs.

Dynamic signatures of microplastic distribution across the water column of Yangtze River Estuary: Complicated implication of tidal effects

Riverine microplastic (MP) discharge into the ocean contributes greatly to global MP contamination, yet our understanding of this process remains primitive. To deepen our interpretation of the dynamic MP variation throughout the estuarine water columns, we sampled at Xuliujing, the saltwater intrusion node of the Yangtze River Estuary, over the course of ebb and flood tides in four seasons (July and October 2017, January and May 2018 respectively). We observed that the collision of downstream and upstream currents contributed to the high MP concentration and that the mean MP abundance fluctuated with the tide. A model of microplastics residual net flux (MPRF-MODEL), taking the seasonal abundance and vertical distribution of MP along with current velocity into consideration, was developed to predict the net flux of MP throughout the full water columns. 2154 ± 359.7 t/year of MP was estimated to flow into the East China Sea via the River in 2017-2018. Our study suggests that riverine MP flux can be overestimated due to reciprocating current carried MP from the estuary. Using the tidal and seasonal variation in MP distribution, we calculated the tide impact factor index (TIFI) for the Yangtze River Estuary to be between 38.11% and 58.05%. In summary, this study provides a baseline of MP flux research in the Yangtze River for similar tidal-controlled rivers and a contextual understanding of how to appropriately sample and accurately estimate in a dynamic estuary system. The redistribution of microplastics may be impacted by complex tide processes. Although not observed in this study, it may merit investigation.

Plastic-Rock Complexes as Hotspots for Microplastic Generation

Discarded plastics and microplastics (MPs) in the environment are considered emerging contaminants and indicators of the Anthropocene epoch. This study reports the discovery of a new type of plastic material in the environment─plastic-rock complexes─formed when plastic debris irreversibly sorbs onto the parent rock after historical flooding events. These complexes consist of low-density polyethylene (LDPE) or polypropylene (PP) films stuck onto quartz-dominated mineral matrices. These plastic-rock complexes serve as hotspots for MP generation, as evidenced by laboratory wet-dry cycling tests. Over 1.03 × 10⁸ and 1.28 × 10⁸ items·m^-2 MPs were generated in a zero-order mode from the LDPE- and PP-rock complexes, respectively, following 10 wet-dry cycles. The speed of MP generation was 4-5 orders of magnitude higher than that in landfills, 2-3 orders of magnitude higher than that in seawater, and >1 order of magnitude higher than that in marine sediment as compared with previously reported data. Results from this investigation provide strong direct evidence of anthropogenic waste entering geological cycles and inducing potential ecological risks that may be exacerbated by climate change conditions such as flooding events. Future research should evaluate this phenomenon regarding ecosystem fluxes, fate, and transport and impacts of plastic pollution.

Effects of UV radiation on natural and synthetic materials

The deleterious effects of solar ultraviolet (UV) radiation on construction materials, especially wood and plastics, and the consequent impacts on their useful lifetimes, are well documented in scientific literature. Any future increase in solar UV radiation and ambient temperature due to climate change will therefore shorten service lifetimes of materials, which will require higher levels of stabilisation or other interventions to maintain their lifetimes at the present levels. The implementation of the Montreal Protocol and its amendments on substances that deplete the ozone layer, controls the solar UV-B radiation received on Earth. This current quadrennial assessment provides a comprehensive update on the deleterious effects of solar UV radiation on the durability of natural and synthetic materials, as well as recent innovations in better stabilising of materials against solar UV radiation-induced damage. Pertinent emerging technologies for wood and plastics used in construction, composite materials used in construction, textile fibres, comfort fabric, and photovoltaic materials, are addressed in detail. Also addressed are the trends in technology designed to increase sustainability via replacing toxic, unsustainable, legacy additives with 'greener' benign substitutes that may indirectly affect the UV stability of the redesigned materials. An emerging class of efficient photostabilisers are the nanoscale particles that include oxide fillers and nanocarbons used in high-performance composites, which provide good UV stability to materials. They also allow the design of UV-shielding fabric materials with impressive UV protection factors. An emerging environmental issue related to the photodegradation of plastics is the generation of ubiquitous micro-scale particles from plastic litter exposed to solar UV radiation.

Synthetic microfiber emissions from denim industrial washing processes: An overlooked microplastic source within the manufacturing process of blue jeans

In recent years, domestic laundry has been recognized as a relevant source of microfiber (MF) pollution to aquatic environments. Nevertheless, the MF emissions from industrial washing processes in real world scenarios have not been quantified. The aim of this study was to quantify the MF emissions from 3 industrial washing processes (rinse wash, acid wash and enzymatic wash) commonly employed in the manufacturing process of blue jeans. The blue jeans were characterized by ATR-FT-IR, SEM and TGA to study the morphology, the polymer chemical identity and the proportion of synthetic and natural fibers, respectively. The MF emissions were quantified as the MF mass and number emitted per washed jean. All the industrial washing processes released a majority of synthetic MF. The enzymatic wash produced the highest amount of MF, with 1423 MF per gram of fabric (MF/g) equivalent to 381.7 MF grams per gram of fabric (MF g/g), followed by the acid wash with 253 MF/g equivalent to 142.7 MF g/g and lastly the rinse wash with 133 MF/g equivalent to 62.3 MF g/g. Statistically significant differences between the MF sizes for all washing processes were found when evaluating the emissions by MF/g, however, the previous trend was not found for MF g/g. Moreover, the total MF emissions of an industrial washing process of a pair of blue jeans during its manufacture process are up to 10.95 times higher than the reported domestic washing estimates performed by the consumer available in the published literature. We demonstrate that studying industrial washing procedures of textile garments will improve the accuracy of the current estimates of MF emissions available in published reports, which will ultimately aid in the development of regulations for MF emissions at an industrial level.

Atmospheric microplastics at a southern China metropolis: Occurrence, deposition flux, exposure risk and washout effect of rainfall

Atmospheric microplastics (AMPs) have raised much concern for public health due to their potential for exposure. In this study, temporal distribution, characteristics and exposure risk of AMPs were studied in the urban area of Guangzhou, a metropolis in Southern China, and the washout effect of rainfall on AMPs was investigated. It was found that AMP abundances in Guangzhou were in a range of 0.01-0.44 items/m³, with higher abundance in the wet season (0.19 ± 0.01 items/m³) than in the dry season (0.15 ± 0.02 items/m³). The distribution of AMPs did not correspond to that of common air pollutants (e.g., PM_2.5 and PM₁₀), implying that their pollution sources might be distinct. In Guangzhou, a total of 1.26 × 10¹¹ items AMPs are in the air every year, and annual inhalation exposure of adults was estimated to be in the range of 79.65-3.50 × 10³ items. The annual deposition flux of AMPs is 65.94 ± 7.53 items/m²/d, and the deposition flux in the wet season (84.00 ± 6.95 items/m²/d) was much greater than that in the dry season (47.88 ± 8.35 items/m²/d). Furthermore, rainfall has an effective mechanism for removing AMPs from the atmosphere, with an average washout ratio of (19.39 ± 6.48) × 10⁴ for rainfall washing AMPs out. Compared to moderate rain (2.5-10 mm/h) and heavy rain (10-50 mm/h), light rain (rainfall intensity <2.5 mm/h) had a better washout effect. This study contributes to the evaluation of AMP exposure risk and understanding of AMP environmental behavior and fate by providing long-term monitoring data on AMPs and quantifying the washout effect of rainfall on AMPs for the first time.

Characterization of fiber fragments released from polyester textiles during UV weathering

Synthetic textiles are considered a prime source of microplastics fibers which are a prevalent shape of microplastic pollution. Whilst the release mechanisms and formation of such microplastic fibers have been so far mainly studied in connection with laundry washing, there are some studies emerging that describe also other release pathways for microplastic fibers such as abrasion during wearing. The aim of this study was to consider weathering as another process contributing to the formation of microplastic fibers and their presence in the environment. Four types of polyester fabrics were selected and exposed to artificial weathering by UV-light for two months. The fabrics were extracted every 15 days to quantify and characterize the formed microplastics. Microplastic fibers with the diameter matching the size of the fibers in the textiles were observed. However, additional microplastic fibers of different shapes were also formed. These included partially broken fibers, thin fibers with a diameter below the size of the fiber in the fabrics, fibers flattened into a ribbon, and non-fibrous microplastics. The released microplastics evinced physical alterations on their surface in the form of pits and cracks. The released microplastics exhibited a steep increase in number with progressing weathering; from hundreds of fibers per gram of textile from unaged fabrics, to hundred thousands fibers (150,000-450,000 MPF/g) after 2 months of weathering. Additional 10,000-52,000 unfibrous microplastics/g were released from the weathered fabrics. While plain fabrics showed higher releases than interlock and fleece, further research is needed to evaluate the importance of the textile architecture on the weathering process in comparison with the production history of the fabrics. Based on a comparison with washing studies with the same textiles, we can estimate that the potential of weathered fabrics to be a source of microplastic fibers can be 20-40 times larger than washing only.

Formation of microplastic fibers and fibrils during abrasion of a representative set of 12 polyester textiles

Microplastic fibers (MPFs) released from synthetic textiles have been found to be a major source of microplastic in the environment. There is increasing evidence available that MPFs released during washing were likely formed during the manufacturing stage. However, real-life use of textiles is often associated with textile-on-textile abrasion, and the first evidence is available that MPFs and finer microplastic fiber fragments (fibrils) are formed during abrasion. In this study, we characterized the formation of MPFs and fibrils from a representative set of 12 polyester textiles after abrasion tests conducted with a Martindale tester. We also investigated the influence of rub intensity and the extractability of MPFs and fibrils from the abraded fabrics. For all textiles, the MPFs extracted after abrasion showed the same diameter as the fibers in non-abraded textiles (10-20 μm), while the extracted fibrils were much thinner (3-5 μm). The variability in the structure of the different polyester textiles led to a broad range of MPF and fibrils extracted during the first wash after 5000 rubs. One gram of textile released between 4900 and 640,000 MPFs and between 0 and 350,000 fibrils with an average fibril/MPF ratio of 0.8. The total number of MPFs and fibrils formed during abrasion was positively correlated with the increase in the number of rubs up to 10,000 times. Visible pilling on the textile surface was an important indicator for the formation of MPFs and fibrils. Our study revealed that textile abrasion is a critical, realistic, and overlooked mechanism for the formation of MPFs and fibrils, as abraded textiles (after 5000 times rubs) can release more than ten times the number of MPFs and fibrils compared to washing only.

Quantification of microfibre release from textiles during domestic laundering

Domestic laundering of textiles is being increasingly recognised as a significant source of microfibre pollution. Reliable quantification of microfibre release is necessary to understanding the scale of this issue and to evaluate the efficacy of potential solutions. This study explores three major factors that influence the quantification of microfibres released from the domestic laundering of textiles: test methodologies, laundering variables, and fabric variables.A review of different test methods is presented, highlighting the variation in quantification created by using different methodologies. A reliable and reproducible method for quantifying microfibre release from domestic laundering is used to explore the impact of laundering and fabric variables experimentally. The reproducibility and reliability of the method used was validated through inter-laboratory trials and has informed the development of European and international testing standards. Our results show that increasing the wash liquor ratio and wash agitation results in a greater mass of microfibres released, but we found that fabric variables can have a greater influence on microfibre release than the laundering variables tested in this study. However, no single fabric variable appeared to have a dominant influence.Using the data obtained and assumptions for washing load size and frequency, results were scaled to reflect possible annual microfibre release from untreated domestic laundering in the UK. Depending on different laundering and fabric variables, these values range from 6490 tonnes to 87,165 tonnes of microfibre discharged in the UK each year.

Formation of Nano- and Microplastics and Dissolved Chemicals During Photodegradation of Polyester Base Fabrics with Polyurethane Coating

Polyurethane (PU) synthetic leathers possess an intricate plastic composition, including polyester (PET) base fabrics and upper PU resin, but the release of fragments from the complexes is unclear. Therefore, we investigated the photodegradation trends of PET base fabrics with PU coating (PET-U) as a representative of composite plastics. Attention was paid to the comparison of the photoaging process of PET-U with that of pure PET base fabric (PET-P). To reveal the potential for chain scission, physical and chemical changes (e.g., surface morphology, molecular weight, and crystallinity) of the two fabrics were explored. The generation of microplastic fibers (MPFs) and microplastic particles (MPPs) was distinguished. Compared with PET-P, PET-U showed a similar but delayed trend in various characteristics and debris release rate as the photoaging time prolonged. Even so, after 360 h of illumination, the generated number of MPs (including MPFs and MPPs) rose considerably to 9.32 × 10⁷ MPs/g, and the amount of released nanoplastics (NPs) increased to 2.70 × 10¹¹ NPs/g from PET-U. The suppression of MP formation from PET-U was potentially directed by the physical shielding of the upper PU layer and the dropped MPs, which resisted the photochemical radical effect. The components of dissolved organic matter derived from plastics (P-DOM) were separated by molecular weight using a size-exclusion chromatography-diode array detector-organic carbon detector/organic nitrogen detector (SEC-DAD-OCD/OND), and the results showed that a larger amount of carbon- and nitrogen-containing chemical substances were generated in PET-U, accompanied by more aromatic and fluorescent compounds. The results provided theoretical bases and insights for future research on the risks of plastic debris from PU synthetic leathers on aquatic organisms and indicated feasible directions for exploring combined pollution studies of plastics.

Microplastic Textile Fibers Accumulate in Sand and Are Potential Sources of Micro(nano)plastic Pollution

Agricultural soils have been identified as sinks for microplastic fibers; however, little information is available on their long-term fate in these soils. In this study, polyester and nylon fibers were precisely cut to relevant environmental lengths, using novel methodology, and their behavior in sand columns was studied at environmental concentration. The longer fibers (>50 μm) accumulated in the upper layers of the sand, smaller fibers were slightly more mobile, and nylon showed marginally higher mobility than polyester. Previous studies have overlooked changes in microplastic morphology due to transport in soil. Our study is the first to show that fibers exhibited breakage, peeling, and thinning under flow conditions in soil, releasing smaller, more mobile fragments. Furthermore, the peelings exhibited different adsorption properties compared to the core fiber. This suggests that microplastic fibers can become a source of smaller micro(nano)plastics and potential vectors for certain molecules, risking continuous contamination of nearby soils, surfaces, and groundwater.

Study on the Relationship between Textile Microplastics Shedding and Fabric Structure

Microplastics refer to plastic fibers, particles or films less than 5 mm in diameter. Textile microplastics are an important form of microplastics, which can harm the ecological environment and human health. This paper studies the relationship between textile microplastic shedding and fabric structure to reduce microplastics pollution and reduce its impact on humans and the natural environment. Firstly, household washing is simulated by considering the main fabric type, the number of steel balls used in the washing, washing temperature, washing time and other influencing factors. An orthogonal test of the mixing level of the four factors is designed by selecting the fabric type, the number of steel balls used in washing, washing temperature and washing time, and the influencing factors is analyzed, and the best washing scheme is obtained. Then, under optimal washing conditions, the three factors and three levels of orthogonal test are designed to analyze the influence of fabric structure and external factors on the shedding of microplastics by changing the amounts of friction and insolation time. The results show that the microplastics released by knitted fabrics are significantly more under the same washing conditions than that of woven fabrics. Satin fabrics released the most microplastics and plain fabrics the least. In addition, among the external factors, the amount of friction significantly affects the production of microplastics.

Hazardous chemical elements in cleaning cloths, a potential source of microfibres

Although potentially hazardous chemical elements (e.g., Cu, Cr, Pb, Sb, Ti, Zn) have been studied in clothing textiles, their presence in cleaning textiles is unknown. In this study, 48 cleaning cloth products (consisting of 81 individual samples) purchased in Europe, and consisting of synthetic (petroleum-based), semi-synthetic or natural fibres or combinations of these different types, have been analysed for 16 chemical elements by X-ray fluorescence (XRF) spectrometry. Titanium was detected in most cases (median and maximum concentrations ~3700 and 12,400 mg kg^-1, respectively) and Raman microspectroscopy revealed that TiO₂ was present as anatase. Barium, Br, Cr, Cu, Fe and Zn were frequently detected over a range of concentrations, reflecting the presence of various additives, and Sb was present at concentrations up to about 200 mg kg^-1 in samples containing polyester as catalytic residue from the polymerisation process. Lead was detected as a contaminant in four samples and at concentrations below 10 mg kg^-1. Overall, the range of the chemical element profiles and concentrations was similar to those for clothing materials published in the literature, suggesting that broadly the same additives, materials and processes are employed to manufacture cloths and clothing textiles. The mechanisms by which potentially hazardous chemical elements are released into the environment with microfibres or mobilised into soluble or nano-particulate forms remain to be explored.

Wiping conditions and fabric properties influenced the microfiber shedding from non-woven products

Disposable wipes and masks have come to be considered as underestimated sources of microfiber generation since the emergence of COVID-19. However, research into the creation of microfibers due to wiping with these non-woven products is scarce, and the potential effects of fabric properties on shedding behavior are unclear. This study investigated microfiber release from 7 wet wipes, 5 dry wipes, and 4 masks in response to the use of simulated daily wiping conditions on artificial skin. The dry wipes (77-568 p per sheet) shed more microfibers than the wet ones (21-190 p per sheet) after 2, 10, or 50 wiping cycles under a 9.8 N wiping force. In addition, an average of 56 microfibers could be released from per gram of wipe, and each square centimeter of wipe could release about 1.18 microfibers during wiping. Masks shed fewer microfibers than wipes due to the excellent shedding resistance of spunbond nonwoven fabrics and the strengthened mechanical properties granted by bonding points. Cellulose, polyethylene terephthalate (PET), and polypropylene (PP) were the major polymers in the microfibers shed by wipes, and the microfibers from masks were all PP. With regard to the influencing factors, the number of microfibers shed from wipes was positively associated with the number of wiping cycles (r = 0.983 and 0.960, p < 0.01) and wiping force (r = 0.980, p < 0.05), while it was negatively correlated with the moisture content (r = -0.992, p < 0.01). Interestingly, a stronger fiber entanglement degree in the wipes significantly improved the resistance to microfiber generation (r = -0.664, p < 0.05). The results highlighted for the first time that the bending coefficient (β = -5.05; 95% CI: -7.71, -2.40; p = 0.002) and fiber extraction force (β = -0.077; 95% CI: -0.123, -0.030; p = 0.005) significantly reduced the tendency for microfiber shedding. Although the number of microfibers shed from wiping was lower than those from domestic washing, there is still an urgent need to control the microfiber shedding tendencies of non-woven products through improving the manufacturing processes.

Plastic Waste Degradation in Landfill Conditions: The Problem with Microplastics, and Their Direct and Indirect Environmental Effects

As landfilling is a common method for utilizing plastic waste at its end-of-life, it is important to present knowledge about the environmental and technical complications encountered during plastic disposal, and the formation and spread of microplastics (MPs) from landfills, to better understand the direct and indirect effects of MPs on pollution. Plastic waste around active and former landfills remains a source of MPs. The landfill output consists of leachate and gases created by combined biological, chemical, and physical processes. Thus, small particles and/or fibers, including MPs, are transported to the surroundings by air and by leachate. In this study, a special focus was given to the potential for the migration and release of toxic substances as the aging of plastic debris leads to the release of harmful volatile organic compounds via oxidative photodegradation. MPs are generally seen as the key vehicles and accumulators of non-biodegradable pollutants. Because of their small size, MPs are quickly transported over long distances throughout their surroundings. With large specific surface areas, they have the ability to absorb pollutants, and plastic monomers and additives can be leached out of MPs; thus, they can act as both vectors and carriers of pollutants in the environment.

Scientometric analysis and scientific trends on microplastics research

In recent years, the environmental pollution of microplastics has attracted much attention. To date, there have been a lot of researches on microplastics and a series of studies published. In this study, by bibliometric analysis method to evaluated the development and evolution on microplastics research trends and hot spots. A total of 2872 literature information was collected from the Web of Science (2004-2020), which was used for bibliometric visual analysis by CiteSpace. It was possible to see the contributing countries, institutions, authors, keywords, and future study directions in the microplastics sectors by looking at the visual representation of the results. (1) Since 2004, scientific advancements in this sector have advanced significantly, with a significant increase in speed since 2012. (2) China and the United States are the world's leading researchers in microplastics. (3) The study of microplastics was multidisciplinary, comprising researchers from the fields of ecology, chemistry, molecular biology, environmental science, and oceanography. (4) In recent years, researchers have concentrated their attention on the distribution and toxicity of microplastics in the environment, as well as their coupled pollution with heavy metal contaminants. In conclusion microplastics study in environmental science has become increasingly popular in recent years. Topics include dispersion, toxicity, and coupled pollution with heavy metal pollutants. Researchers in a wide range of fields are involved in microplastics research. Furthermore, policies and regulations about microplastics in global were summarized, and membrane technology has potential to remove microplastics from water. The above findings help to clearly grasp the content and development trend of microplastics research, point out the future research direction for scholars, and promote microplastics research and pollution prevention and control.

Fate of microfibres from single-use face masks: Release to the environment and removal during wastewater treatment

Single-use face masks can release microfibres upon exposure to environmental conditions. This study investigates the number of microfibres released in the presence and absence of UV irradiation and mechanical friction and the removal of the released microfibres in a simulated conventional wastewater treatment process. UV exposure results in a four-fold increase in the number of microfibres released from new masks and used masks resulting in ~2400 microfibres/mask and ~1100 microfibres/mask, respectively. Application of mechanical friction to the UV-exposed new and used masks further increases the number of released microfibres per mask. In a simulated coagulation/flocculation process, the removals of microfibers originating from new masks and used masks are 79% and 91%, respectively. XPS analysis reveals that the silica content of the used masks is 240% higher than that of new masks, which could explain the higher removal efficiency of microfibers from used masks. FTIR analysis of the masks after UV exposure shows carbonyl indices of 0.73 ± 0.70 and 0.27 ± 0.10 for the microfibres from used and new masks, respectively. Based on available data, we estimate that 4-47 million polypropylene microfibres can be released into natural waters per day after wastewater treatment in an urban environment (for a population of 4300 persons/km²).

Acute and multigenerational effects of petroleum- and cellulose-based microfibers on growth and photosynthetic capacity of Lemna minor

Comparative toxicological assessment studies on the effects of petroleum- and cellulose-based microfibers on aquatic plants are limited. Therefore, we evaluated the acute and 10-generational toxicological effects of two types of petroleum- and cellulose-based microfibers on the duckweed Lemna minor. Plant growth and photosynthesis parameters were monitored as bioindicators. The multigenerational test revealed the following ranking of the microfibers according to the severity of their effects on L. minor: polypropylene > lyocell > viscose > polyethylene terephthalate. The acute tests revealed a significant increase in the energy required to initiate photosynthesis, although the growth of L. minor was not adversely affected by any microfiber. Both petroleum- and cellulose-based microfibers induced adverse effects on the growth and photosynthesis of L. minor in multigenerational tests. The results of the generational tests contribute to the understanding of the long-term adverse effects of microfibers on aquatic plants.

The Effect of the Physical and Chemical Properties of Synthetic Fabrics on the Release of Microplastics during Washing and Drying

Synthetic fibers released during washing are the primary source of microplastic pollution. Hence, research on reducing the release of microplastic fibers during washing has recently attracted considerable attention. As a result of previous studies, there is a difference in the amount of microplastic emission according to various types of fabrics. To mitigate the release of microplastics, the study of the reason for the difference in the amount of microplastics is needed. Therefore, this study investigated different synthetic fabrics that release microplastics and the physical properties of the fabrics that affect the release of fibers. Three types of fabrics with different chemical compositions were analyzed. The washing and drying processes were improved by focusing on the mechanical factors that affected microplastic release. Furthermore, based on the mass of the collected microplastic fibers, it was found that the chemical compositions of the fabric can affect the microplastics released during washing and drying. This evaluation of physical properties helped to identify the physical factors that affect microplastic release. These results may provide a basis for reducing microplastic fiber types, thereby minimizing unintended environmental pollution.

Wastewater treatment plants act as essential sources of microplastic formation in aquatic environments: A critical review

According to extensive in situ investigations, the microplastics (MPs) determined in current wastewater treatment plants (WWTPs) are mostly aged, with roughened surfaces and varied types of oxygen-containing functional groups (i.e., carbonyl and hydroxyl). However, the formation mechanism of aged MPs in WWTPs is still unclear. This paper systematically reviewed MP fragmentation and generation mechanisms in WWTPs at different treatment stages. The results highlight that MPs are prone to undergo physical abrasion, biofouling, and chemical oxidation-associated weathering in WWTPs at different treatment stages and can be further decomposed into smaller secondary MPs, including in nanoplastics (less than 1000 nm or 100 nm in size), suggesting that WWTPs can act as a formation source for MPs in aquatic environments. Sand associated mechanical crashes in the primary stage, microbes in active sewage sludge-related biodegradation in the secondary stage, and oxidant-relevant chemical oxidation processes (light photons, Cl₂, and O₃) in the tertiary stage are the dominant causes of MP formation in WWTPs. For MP formation mechanisms in WWTPs, external environmental forces (shear and stress forces, UV radiation, and biodegradation) can first induce plastic chain scission, destroy the plastic molecular arrangement, and create abundant pores and cracks on the MP surface. Then, the physicochemical properties (modulus of elasticity, tensile strength and elongation at break) of MPs shift consequently and finally breakdown into smaller secondary MPs or nanoscale plastics. Overall, this review provides new insights to better understand the formation mechanism, occurrence, fate, and adverse effects of aged microplastics/nanoplastics in current WWTPs.

Exposure to textile microfibers causes no effect on blood, behavior and tissue morphology in the three-spined stickleback (Gasterosteus aculeatus)

We assessed textile microfibers impacts on the three-spined stickleback, using synthetic and natural fibers originating from yarns or washer effluents. After water exposure at 200 fibers/L, we assessed fish survival, behavior, tissue morphology and hemoglobin concentration, and paid special attention to exposure characterization. We report quantitative fiber distribution in the exposure system, fiber size distribution, and contamination. We provide a fiber preparation procedure and exposure method intended to ensure accurate and stable concentrations over time. Following exposure, no effect was observed on the studied endpoints in any of the treatment conditions. We observed fast sinking of the fibers. Fish organs and feces contained 1.3% and 6.8% of recovered fibers, and 12.6% fibers were found adhered to the tank walls. We show that water renewals in semi-static exposures is a critical step for the maintenance of stable concentrations, and discuss the practical and/or methodological challenges associated to the study of microfibers.

Nanomaterials for microplastic remediation from aquatic environment: Why nano matters?

The contamination of microplastics in aquatic environment is regarded as a serious threat to ecosystem especially to aquatic environment. Microplastic pollution associated problems including their bioaccumulation and ecological risks have become a major concern of the public and scientific community. The removal of microplastics from their discharge points is an effective way to mitigate the adverse effects of microplastic pollution, hence has been the central of the research in this realm. Presently, most of the commonly used water or wastewater treatment technologies are capable of removing microplastic to certain extent, although they are not intentionally installed for this reason. Nevertheless, recognizing the adverse effects posed by microplastic pollution, more efforts are still desired to enhance the current microplastic removal technologies. With their structural multifunctionalities and flexibility, nanomaterials have been increasingly used for water and wastewater treatment to improve the treatment efficiency. Particularly, the unique features of nanomaterials have been harnessed in synthesizing high performance adsorbent and photocatalyst for microplastic removal from aqueous environment. This review looks into the potentials of nanomaterials in offering constructive solutions to resolve the bottlenecks and enhance the efficiencies of the existing materials used for microplastic removal. The current efforts and research direction of which studies can dedicate to improve microplastic removal from water environment with the augmentation of nanomaterial-enabled strategies are discussed. The progresses made to date have witnessed the benefits of harnessing the structural and dimensional advantages of nanomaterials to enhance the efficiency of existing microplastic treatment processes to achieve a more sustainable microplastic cleanup.

Emerging microplastics in the environment: Properties, distributions, and impacts

Microplastics (MPs) are emerging and recalcitrant micropollutants in the environment, which have attracted soaring interests from a wide range of research disciplines. To this end, numerous technologies have been devised to understand the properties, environmental behaviors, and potential impacts/hazards of MPs. Herein, we present a review on the properties, environmental distribution and possible impacts. In this review, a comprehensive introduction of the most universal types of MPs, their shapes and characters will be first presented. Then the distributions of MPs in the environment and the impacts on microbe, plants, and human will be reported. Finally, major challenges and directions will be discussed to provide some clues to the better understanding, control and migration of MPs pollution in future studies.

Less impact than suspected: Dietary exposure of three-spined sticklebacks to microplastic fibers does not affect their body condition and immune parameters

Microplastic fibers are frequent anthropogenic contaminants in most aquatic environments and have consequently been detected in the digestive tract of many fish species. Upon ingestion, microplastic fibers pose risks of interference with nutrient uptake, impaired intestinal health, and as a consequence may alter growth performance and fitness. In addition, foreign particles such as fibers might cause tissue irritations and stress, and thus interfere with immune parameters. In nature, fish regularly encounter microplastic fibers as well as fiber debris from natural sources and materials. Thus, we wanted to test the potential impact of microplastic fibers on growth, organosomatic indices, and immune parameters of subadult fish and compare these to possible effects caused by natural fibers. We administered sticklebacks diets, which were supplemented with either polyester or cotton fibers (each at concentrations of 0.2 mg/g and 2 mg/g feed) or a control diet without fiber supplementation for nine weeks. Mortalities did not occur and sticklebacks grew equally well across treatments. Neither organosomatic indices nor immune parameters revealed significant differences between treatments. While natural differences between males and females were observed for some parameters, no treatment-related gender-specific effects were detected. Our results suggest that the dietary uptake of polyester fibers does not affect growth, body condition, gonad development, and immunity of sticklebacks - even at fiber concentrations higher than what can be encountered in the wild. Furthermore, virgin microplastic fibers do not seem to affect fish differently than fibers from natural origin. The present study implies that at least some species are resilient towards pollution with (virgin) microplastic fibers even at high concentrations.

A review of microplastic fibres: generation, transport, and vectors for metal(loid)s in terrestrial environments

The laundering of synthetic fabrics has been identified as an important and diffuse source of microplastic (<5 mm) fibre contamination to wastewater systems. Home laundering can release up to 13 million fibres per kg of fabric, which end up in wastewater treatment plants. During treatment, 72-99% of microplastics are retained in the residual sewage sludge, which can contain upwards of 56 000 microplastics per kg. Sewage sludge is commonly disposed of by application to agricultural land as a soil amendment. In some European countries, application rates are up to 91%, representing an important pathway for microplastics to enter the terrestrial environment, which urgently requires quantification. Sewage sludge also often contains elevated concentrations of metals and metalloids, and some studies have quantified metal(loid) sorption onto various microplastics. The sorption of metals and metalloids is strongly influenced by the chemical properties of the sorbate, the solution chemistry, and the physicochemical properties of the microplastics themselves. Plastic-water partition coefficients for the sorption of cadmium, mercury and lead onto microplastics are up to 8, 32, and 217 mL g^-1 respectively. Sorptive capacities of microplastics may increase over time, due to environmental degradation processes increasing the specific surface area and surface density of oxygen-containing functional groups. A range of metal(loid)s, including cadmium, chromium, and zinc, have been shown to readily desorb from microplastics under acidic conditions. Sorbed metal(loid)s may therefore become more bioavailable to soil organisms when the microplastics are ingested, due to the acidic gut conditions facilitating desorption. Polyester (polyethylene terephthalate) should be of particular focus for future research, as few quantitative sorption studies currently exist, it is potentially overlooked from density separation studies due to its high density, and it is by far the most widely used fibre in apparel textiles production.

Microplastics in Wastewater by Washing Polyester Fabrics

Microplastics have become one of the most serious environmental hazards today, raising fears that concentrations will continue to rise even further in the near future. Micro/nanoparticles are formed when plastic breaks down into tiny fragments due to mechanical or photochemical processes. Microplastics are everywhere, and they have a strong tendency to interact with the ecosystem, putting biogenic fauna and flora at risk. Polyester (PET) and polyamide (PA) are two of the most important synthetic fibres, accounting for about 60% of the total world fibre production. Synthetic fabrics are now widely used for clothing, carpets, and a variety of other products. During the manufacturing or cleaning process, synthetic textiles have the potential to release microplastics into the environment. The focus of this paper is to explore the main potential sources of microplastic pollution in the environment, providing an overview of washable polyester materials.

Mugilidae fish as bioindicator for monitoring plastic pollution: Comparison between a commercial port and a fishpond (north-western Mediterranean Sea)

In the last decade, interest in monitoring and managing plastic pollution has greatly increased. This study compared levels of microplastic contamination in stomachs of Mugilidae fish, suggesting this family as a target for plastic pollution monitoring in areas with different degrees of anthropisation. Two sites characterised by low and high anthropic impact, a fishpond (S'Ena Arrubia, Italy) and a port (Genoa, Italy), respectively, were compared. This study highlighted a stronger microplastic contamination in the port, with a higher percentage of fish showing the presence of microplastics and a larger polymeric variability compared to the fishpond. The microplastic number in fish from the port was higher than in the literature, but it was not significantly different from S'Ena Arrubia in terms of the microplastic percentage found in single individuals. Biomonitoring of microplastic contamination in Mugilidae fish resulted in a valid tool for the investigation of areas differently affected by human activity.

Release of microplastics from typical rainwater facilities during aging process

As the demand for urban flood prevention and drainage increases, a large number of plastic rainwater facilities are in use. Microplastics will be released inevitably into stormwater systems during aging and hydraulic scouring processes, which could cause potential pollution risk. This study simulated the release behavior of microplastics from three typical plastic rainwater facilities including a rainwater inspection well, rainwater storage module, and rainwater pipe (mainly composed of high-density polyethylene, polypropylene, and polyvinyl chloride, respectively) under the effects of aging and hydraulic scouring. After 15-45 days of UV aging and 72 h of hydraulic scouring, the surfaces of the three facilities were found to exhibit increases in roughness, cracks, folds, and cavities, with the most pronounced changes occurring in the rainwater storage module. As the aging time increased, oxygen-containing functional groups formed and led to carbon chain scission. Fourier transform infrared spectroscopy (FTIR), two-dimensional correlation spectroscopy (2D-COS) and X-ray photoelectron spectroscopy (XPS) of facility surfaces showed that the formation of oxygen-containing functional groups was an important factor affecting the release of microplastics. The amount of microplastics released from the three facilities ranged from 160 to 1905 items/g (microplastics/facilities), following in the order of rainwater inspection well > rainwater storage module > rainwater pipe. The particle size of the released microplastics ranged from 3 to 1363 μm, with 10-30 μm accounting for the greatest proportion of particles, 50.10%. The size of microplastics released from the rainwater inspection well and rainwater storage module increased with the aging degree, while the release from the rainwater pipe decreased. The release behavior depends mainly on the composition of the materials and the aging time. Thus, microplastics can be released from plastic rainwater facilities under suitable conditions. The results can be used to further evaluate microplastic pollution caused by urban rainwater facilities.

Reuse of Water in Laundry Applications with Micro- and Ultrafiltration Ceramic Membrane

This study compares the performance of a microfiltration membrane, made by silicon carbide (SiC) and an ultrafiltration membrane, made by zirconia (ZrO₂), in the treatment of wastewater from a washing machine designed to clean industrial tents. The filtration of deionized water, containing model microplastics (i.e., nylon fiber), was performed. This was followed by the filtration of real wastewater from a single washing cycle of industrial tents, made from polyvinyl chloride (PVC) textile. The filtration parameters of the membranes and physical-chemical parameters of the wastewater, including the concentration of microplastics in the shape of tent fibers (PVC), were calculated before and after filtration. The microfiltration membrane manifested a greater decrease in permeability (95%) compared to the ultrafiltration membrane (37%). The resulting water quality in terms of Total Solids, turbidity, and microplastics concentration was better for the ultrafiltration. This is evident from 99.2% versus 98.55% removal efficiency of microplastics from the laundering wastewater, respectively.

Improved Settling Velocity for Microplastic Fibers: A New Shape-Dependent Drag Model

Microplastics are abundant in aquatic environments and are an emerging environmental concern. The prediction of their settling velocities is central to predictions of the residence time and concentration depth profiles of microplastics in aquatic environments. The main scientific challenge in improving the current understanding of the settling motions of microplastics is that existing drag models are deficient at reasonably predicting the settling velocities of various microplastics, especially microplastic fibers. This is because the shape factors used in the existing drag models cannot morphologically distinguish fibers from fragments and films. In this study, a new shape factor, specifically the Aschenbrenner shape factor, is proposed as a vehicle to explicitly distinguish among the morphologies of fibers, films, and fragments. With this new shape factor, a new drag model is developed and then systematically evaluated against the unique set of data provided by new experiments conducted in this study along with four other published data sets in the literature. The proposed model allows the prediction of the terminal settling velocity of microplastic fibers more accurately than existing drag models. Moreover, the new model has also shown its applicability to microplastic films and fragments. Notwithstanding, the new model appears deficient at reasonably predicting the terminal settling velocity of weathered microplastics in the field, which requires further investigations.

Prevalence of microplastic fibers in the marginal sea water column off southeast China

Microplastic (MP) fibers are present in all environmental media, yet little is known about their distribution, sources, and transport in the water column of marginal seas. In this study, we conducted an intensive sampling campaign in the marginal sea water column off southeast China, which is an area that is greatly influenced by high MP emissions. We found that hydrological effects largely regulated the spatial variations of MP fiber distribution and that MP fibers likely were not entering the South China Sea through terrestrial input from southeast China during the summer monsoon. Polyethylene terephthalate (PET) fibers were pervasive in the surface water (SW) (89.47%), subsurface chlorophyll maximum layer (SCML) (92.65%), and bottom water (BW) (94.29%) of the water column during the sampling period. Approximately 32% of MP fibers in the samples were smaller than 330 μm. The abundance of MP fibers in SW was significantly lower than that in the SCML and BW. Based on this observation, we estimated the inventory of MP fibers in the SW, SCML, and BW of the sampling area to be 1.377-1.378, 2.820-2.825, and 2.627-2.629 metric tons, respectively. These results improved our understanding of the source-to-sink process of MP fiber contamination in the water column of marginal seas.

Environmental Impacts of Microplastics and Nanoplastics: A Current Overview

The increasing distribution of miniaturized plastic particles, viz. microplastics (100 nm–5 mm) and nanoplastics (less than 100 nm), across the various ecosystems is currently a subject of major environmental concern. Exacerbating these concerns is the fact that microplastics and nanoplastics (MNPs) display different properties from their corresponding bulk materials; thus, not much is understood about their full biological and ecological implications. Currently, there is evidence to prove that these miniaturized plastic particles release toxic plastic additives and can adsorb various chemicals, thereby serving as sinks for various poisonous compounds, enhancing their bioavailability, toxicity, and transportation. Furthermore, there is a potential danger for the trophic transfer of MNPs to humans and other higher animals, after being ingested by lower organisms. Thus, this paper critically analyzes our current knowledge with regard to the environmental impacts of MNPs. In this regard, the properties, sources, and damaging effects of MNPs on different habitats, particularly on the biotic components, were elucidated. Similarly, the consequent detrimental effects of these particles on humans as well as the current and future efforts at mitigating these detrimental effects were discussed. Finally, the self-cleaning efforts of the planet via a range of saprophytic organisms on these synthetic particles were also highlighted.