Wetting of Superhydrophobic Polylactic Acid Micropillared Patterns

Application of Argon Ion Implantation to Improve the Surface Properties of Materials Based on PLA and Lignocellulosic Particles

The new wood-plastic composites (WPC) biocomposites, a promising blend of poly(lactic acid) (PLA) and lignocellulosic fillers, are the subject of our study. We used bark and sawdust at 40, 50, and 60% as PLA fillers. The innovative use of ion implantation to modify the surface properties of the produced composites could have significant implications. Argon ions were used in three dosages (1 × 1015, 1 × 1016, and 1 × 1017 cm-2) at an accelerating voltage of 60 kV. The modified composites were then analyzed for changes in surface wettability, surface energy, and color. Our findings demonstrate that the dosage of argon ion implantation and the filler used have a profound impact on the properties of the modified surfaces. In general, ion implantation enhances the surface wettability of composites and pure PLA, with the recorded relationships being more pronounced in composites containing higher proportions of lignocellulosic fillers. Furthermore, the implantation of ions on the surface of composites induces changes in their color, opening up new possibilities for the field of materials science.

Alkali-Free Oxidation of 1,2-Propanediol to Lactic Acid over Intermetallic Cu1Pt Compounds

Polylactic acid (PLA) plastics are the most popular biodegradable and biocompatible materials; however, their monomer, lactic acid (LA), is currently produced via an inefficient fermentation process. Herein, activated carbon-supported Pt-Cu intermetallic compounds were synthesized and utilized in the selective oxidation of 1,2-propanediol (1,2-PDO) toward LA without the participation of homogeneous alkali or a basic support. It was found that rhombohedral intermetallic Cu1Pt compounds exhibited excellent performance and the calculated turnover frequency of each surface Pt atom reached 10 049 h-1. The yield of free LA reached 64.6% with a complete conversion of 1,2-PDO at 100 °C within 2 h. Diverse characterization and DFT calculations revealed that Pt-Cu intermetallic compounds were active for the adsorption and/or activation of molecular oxygen and 1,2-PDO. Raman analysis of adsorbed 1,2-PDO further disclosed that 1,2-PDO contacted with rhombohedral intermetallic Cu1Pt compounds strongly, and then the oxidation of the terminal hydroxyl group was performed preferentially, which promoted the formation of LA.

Development of Functionalized Polylactide Thin Films Using Poly(methylhydrogenosiloxane) Sol-Gel Process with Improved Antifouling Properties

Biobased polylactide (PLA) films were modified with low reticulate polysiloxane gel acting as a scalable platform for the hydrophilization of polymeric film surface. The PLA thin film was first coated with poly(methylhydrogenosiloxane) (PMHS) by the sol-gel transition via the condensation of diethoxymethylsilane (DH) and triethoxysilane (TH) using trifluoromethanesulfonic acid as a catalyst. Then, hydrosilylation of Si-H bonds in the presence of Karstedt's catalyst allowed the covalent grafting of hydrophilic alkene-containing molecules, i.e., triethylene glycol monomethyl allyl (TEGMEA) and a new zwitterionic allylcarboxybetaine (ACB) synthesized for the first time by the quaternization of dimethyl allyl amine (DMAA) with β-propiolactone. PMHS coating on the PLA film was evidenced by Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The observation by atomic force microscopy (AFM) revealed a homogeneous coating with low roughness (RMS = 0.29 nm). The hydrophilicity of functionalized PLA films was determined by water contact angle (WCA) measurements using the captive bubble method. A large increase in wettability properties was observed for both grafting with TEGMEA (WCA = 38°) and ACB (WCA = 42°) in comparison with the native PLA film (WCA = 80°). Moreover, the biocompatibility and antifouling efficiency of functionalized PLA films were evaluated by protein adsorption, bacterial adhesion, and cytotoxicity tests. The results indicate that the grafting of the two types of hydrophilic compounds does not affect the biocompatibility of PLA while significantly reducing protein adsorption and bacterial adhesion, thus showing the great potential of this surface functionalization strategy for applications in the medical field.

Synthesis of star-shaped poly(lactide)s, poly(valerolactone)s and poly(caprolactone)s via ROP catalyzed by N-donor tin(ii) cations and comparison of their wetting properties with linear analogues

In this study, we report the use of N-coordinated tin(ii) cations [L1→Sn(H2O)][OTf]2·THF (1) and [L1→SnCl][SnCl3] (2) (L1 = 1,2-(C5H4N-2-CH = N)2CH2CH2) as efficient ROP catalysts, which, in combination with benzyl alcohol, afford well-defined linear poly(ε-caprolactone) (PCL) and poly(δ-valerolactones) (PVL) via an activated monomer mechanism (AMM). Thanks to the versatility of complexes 1 and 2 as catalysts, star-shaped PCL, PVL and PLA were also prepared using three-, four-, five- and six-functional alcohols. The number of arms was determined by SEC-MALS-Visco analysis. Spin-coated thin layers of linear and selected six-armed polymers were further studied in terms of their wettability to water. Attention was focused on the influence of the composition and structure of the polymers. Finally, to increase the hydrophobic properties of the studied polymers, stannaboroxines L2(Ph)Sn[(OB-(C6H4-4-CF3))2O] and L2(Ph)Sn[(OB-(C6H4-3,5-CF3)2)2O] (L2 = C6H3-2,6-(Me2NCH2)2) were applied.

A MAX phase (Ti3AlC2) as a performance enhancer for poly(lactic acid) electrospun membranes in steam generation and solar desalination

Clean water and sanitation issues motivate researchers to develop water evaporators for freshwater generation. The composite membrane evaporator was electrospun herein based on poly(lactic acid) (PLA) and Ti3AlC2 MAX phase as a property enhancer. As a precursor for the MXenes synthesis, the MAX phase has never been explored with PLA for water evaporator potential. Alternative use of the MAX phase can reduce the production cost arising from chemical synthesis. This work explored the potential of the MAX phase as an additive to enhance PLA membrane performance for steam generation and desalination applications. Under the infrared irradiation (∼1.0 kW/m2), the mechanically-improved PLA/MAX phase membrane showed an enhanced water evaporation rate of 1.70 kg/m2 h (93.93 % efficiency), with an approximately 52 % rate increment relative to the PLA membrane. Based on the artificial seawater (3.5 % w/w), the membrane exhibited an evaporation rate of 1.60 kg/m2 h (87.57 % efficiency). The membrane showed self-floating ability at the air-water interface, excellent thermal stability over the entire operating temperatures, and reusability after repeated cycles. Moreover, the generated freshwater contained exceptionally low cations concentrations, as low as those in potable water. The developed composite membrane also had proved its potential for solar desalination in the water generation field.

Effect of Collector Rotational Speed on the Morphology and Structure of Solution Blow Spun Polylactic Acid (PLA)

Apart from structure and composition, morphology plays a significant role in influencing the performance of materials in terms of both bulk and surface behavior. In this work, polylactic acid (PLA) constituted by submicrometric fibers is prepared. Using a modified electrospinning (ES) device to carry out solution blow spinning (SBS), the fibrillar morphology is modified, with the aim to induce variations in the properties of the material. The modification of the ES device consists of the incorporation of a source of pressurized gas (air) and a 3D-printed nozzle of our own design. For this work, the morphology of the PLA submicrometric fibers is modified by varying the rotational speed of the collector in order to understand its influence on different properties and, consequently, on the performance of the material. The rotational speed of a cylindrical collector (250, 500, 1000 and 2000 rpm) is considered as variable for changing the morphology. Morphological study of the materials was performed using scanning electron microscopy and image analysis carried out with ImageJ 1.54f software. Besides a morphology study, structural characterization by Fourier transformed infrared spectroscopy using attenuated total reflectance of prepared materials is carried out. Finally, the morphology and structure of produced PLA fibrous mats were correlated with the analysis of mechanical properties, wettability behavior and adhesion of DH5-α E. coli bacteria. It is of interest to highlight how small morphological and chemical structure variations can lead to important changes in materials' performance. These changes include, for example, those above 30% in some mechanical parameters and clear variations in bacterial adhesion capacity.

In Vivo Laser-Induced Vasoactive Microenvironmental Setting via a Stimuli-Responsive Microstructured Depot

A stimuli-responsive polymeric three-dimensional microstructured film (PTMF) is a 3D structure with an array of sealed chambers on its external surface. In this work, we demonstrate the use of PTMF as a laser-triggered stimulus-response system for local in vivo targeted blood vessels stimulation by vasoactive substances. The native vascular networks of the mouse mesentery were used as model tissues. Epinephrine and KCl were used as vasoactive agents that were sealed into individual chambers upon precipitation in the amount of pictograms. We demonstrated the method for non-damaged one-by-one chamber activation using a focused 532 nm laser light passed through biological tissues. To avoid laser-induced photothermal damage to biological tissues, the PTMF was functionalized with Nile Red dye, which effectively absorbs laser light. Chemically stimulated blood vessel fluctuations were analyzed using digital image processing methods. Hemodynamics changes were measured and visualized using the particle image velocimetry approach.

Droplet Size-Assisted Polysiloxane Architecting

(Super)antiwetting shielding around engineering materials and protecting them against harsh environmental conditions have been achieved via growing various geometry polysiloxane (or silicone) patterns around them by using a droplet-assisted growth method, where the polymerization takes place inside of the water droplets acting as reaction vessels. The size and distribution of these reaction vessels are the main factors in making different geometry silicone patterns; however, very little is known about the fate of these droplets throughout the polymerization. Here, we propose keeping the relative humidity (% RH) inside the reactor stable throughout the polymerization as a new coating parameter to force the size of the reaction vessel water droplets to be the same for building simply shaped silicone rods with controlled geometry and distribution. In this manner, we grew simple geometry cylindric microrods on surfaces and could tune their length, diameter, inter-rod spacing, and thus the (super)hydrophobicity. Here, we also demonstrate that with changes in the amplitude and stability of the % RH, it is possible to fabricate different (super)hydrophobic nanograsses, conical silicone microrods, and isotropic silicone nanofilaments. The proposed new way of tuning initial and in situ reaction vessel droplet size can be used as a single factor to formulate different geometry silicone patterns with tunable dimensions, leading to different roughness and hydrophobicity. To a certain extent, the droplet size-assisted silicone shaping in this work provides a new way to control the length, diameter, morphology, inter-rod spacing, and thus the (super)hydrophobicity of the silicone patterns, especially those in the shape of simple cylindrical microrods. This control over silicone architecting will help to prepare new (super)hydrophobic coatings with more controlled morphology and thus wettability; on the contrary, it will support surface scientists modeling the connection between surface geometry and (super)antiwetting of such irregular pillared surfaces that remain elusive.