Heat Conduction and Antibacterial Hexagonal Boron Nitride/Polypropylene Nanocomposite Fibrous Membranes for Face Masks with Long-Time Wearing Performance

Antibacterial nonwoven materials in medicine and healthcare

Bacterial infection has always been a severe challenge for mankind. The use of antibacterial nonwoven materials provides a lot of convenience in daily life and clinical practice grammar revision, it has become an important solution to avoid bacterial infection in clinical and daily life. This review systematically examines the spin bonding, melt blown, hydroneedling and electrospinning methods of nonwoven fabrication materials, and summarizes the antibacterial nonwoven materials fabrication methods. Finally, the review discusses the applications of antibacterial nonwoven materials for medical protection, external medical and healthcare, external circulation medical care implantable medical and healthcare and intelligent protection and detection. This comprehensive overview aims to provide valuable insights for the advancement of antibacterial nonwoven materials in the domain of medicine and health care. In the future, antibacterial nonwoven materials are expected to evolve towards biodegradability, composite materials, functionalization, minimally invasive techniques, diversification, and intelligence, thereby holding immense potential in healthcare.

High-efficiency respiratory protection and intelligent monitoring by nanopatterning of electroactive poly(lactic acid) nanofibers

The advent of multifunctional nanofibrous membranes (NFMs) has led to the development of next-generation air filters that are ready to intercept fine particulate matters (PMs) and monitor the respiratory diseases. However, it is still challenging to fabricate biodegradable NFMs featuring the desirable combination of high filtration efficiencies, low air resistance, and intelligent real-time monitoring. Herein, a hierarchical nanopatterning approach was proposed to functionalize the stereocomplexed poly(lactic acid) (PLA) (SC-PLA) nanofibers via the combined electrospinning of SC-PLA and electrospray of CNT@ZIF-8 nanohybrids. The nanopatterned SC-PLA (NSC-PLA) NFMs were characterized by largely increased surface activity and electroactivity, as evidenced by the nearly two-fold increase in surface potential (up to 7.3 kV) and substantial improvements in the dielectric properties. Furthermore, the NSC-PLA NFMs exhibited excellent tribo-output performance, yielding a voltage of as high as 13.5 V for NSC-PLA NFMs loaded 10 % nanohybrids (NSC-PLA10). In particular, the exceptionally high electroactivity and unique protrusion structure together contributed to promote the filtration efficiencies, while providing a low pressure drop (e.g., 96.1 % for PM2.5 and 88.3 % for PM0.3, only 67.6 Pa of NSC-PLA10, at 32 L/min). More importantly, NSC-PLA NFMs enabled real-time monitoring of physiological signals during different respiratory states, as evidenced by the output voltages of 17.2, 32.9 and 37.5 mV for normal breath, fast breath and cough recorded by NSC-PLA10. The proposed NSC-PLA NFMs show enormous potential in the fields of air filtration and real-time respiratory monitoring, thus providing ecofriendly solutions to personal health management.

Functionalized cellulose nanocrystals reinforced PLA-gelatin electrospun fibers for potential antibacterial wound dressing and coating applications

This study addresses the critical need for effective antibacterial materials by exploring the innovative integration of dimethyloctadecyl [3-(trimethoxysilyl)propyl] ammonium chloride (DTSACl) onto cellulose nanocrystal (CNC), followed by its incorporation into polylactic acid and gelatin matrices to engineer antibacterial nanofiber mats. The modification of CNC with DTSACl (QACNC) was studied and confirmed by FT-IR, 13C NMR, and XRD analysis. Furthermore, the impact of such addition on the morphology, mechanical, hydrophobic properties, and antibacterial efficacy of the resultant QACNC nanofibers were thoroughly investigated. It was found that the QACNC inhibited the growth of Staphylococcus aureus by 99 % but had no effect on Pseudomonas aeruginosa at 125 μg/mL concentration. Various concentrations of QACNC were blended into the as-spun PLA/Gel solutions before spinning or coated onto spun PLA/Gel nanofiber mats. There was a minor antibacterial effect observed with PLA/Gel mats blended with up to 3 wt% QCNC, while the average inhibition for PLA/Gel/QACNC 5 wt% was 68.3 % ± 36.5 %. By increasing the amount of QACNC blended into the polymer matrix, the human dermal fibroblast (HDF) cell viability decreased, indicating that optimizing QACNC concentrations is crucial for maintaining cell viability while ensuring effective antibacterial performance. Given the enhanced antibacterial properties, the fabricated textiles hold significant potential for applications in medical textiles and wound dressings.

Electroactive polylactic acid nanofiber multilayer membranes as "Green" flexible electrode for supercapacitor

Against the backdrop of the post-COVID-19 era, the demand for masks has become increasingly steady, discarded masks have brought about new environmental problems due to the lack of effective means of disposal as well as recycling mechanisms. To solve this problem, we make secondary use of discarded polylactic acid (PLA) masks. The nanofiber multilayer membranes PLA/PDA/GO/PPy were synthesized by layer-by-layer self-assembly for flexible supercapacitors (SCs). The multiple coating on PLA significantly increases the capacitive performance. Optimization of the PLA/PDA/GO/PPy demonstrates capacitance up to 1331 mF cm-2. Symmetric aqueous SCs using PLA/PDA/GO/PPy electrodes show higher energy density than other literature-reported SCs based on nanofiber multilayer membranes. In addition, we also explored the effects of discarded PLA/PDA/GO/PPy on the growth of ryegrass and canola in the soil. The exceptional combination of remarkable electrochemical properties and excellent environmental friendliness makes the PLA membrane promising for supercapacitors.

Emerging trends and future challenges of advanced 2D nanomaterials for combating bacterial resistance

The number of multi-drug-resistant bacteria has increased over the last few decades, which has caused a detrimental impact on public health worldwide. In resolving antibiotic resistance development among different bacterial communities, new antimicrobial agents and nanoparticle-based strategies need to be designed foreseeing the slow discovery of new functioning antibiotics. Advanced research studies have revealed the significant disinfection potential of two-dimensional nanomaterials (2D NMs) to be severed as effective antibacterial agents due to their unique physicochemical properties. This review covers the current research progress of 2D NMs-based antibacterial strategies based on an inclusive explanation of 2D NMs' impact as antibacterial agents, including a detailed introduction to each possible well-known antibacterial mechanism. The impact of the physicochemical properties of 2D NMs on their antibacterial activities has been deliberated while explaining the toxic effects of 2D NMs and discussing their biomedical significance, dysbiosis, and cellular nanotoxicity. Adding to the challenges, we also discussed the major issues regarding the current quality and availability of nanotoxicity data. However, smart advancements are required to fabricate biocompatible 2D antibacterial NMs and exploit their potential to combat bacterial resistance clinically.

Cellulose Nanofiber-Based Triboelectric Nanogenerators for Efficient Air Filtration in Harsh Environments

Advanced portable healthcare devices with high efficiencies, small pressure drops, and high-temperature resistance are urgently desired in harsh environments with high temperatures, high humidities, and high levels of atmospheric pollution. Triboelectric nanogenerators (TENGs), which serve as energy converters in a revolutionary self-powered sensor device, present a sustainable solution for meeting these requirements. In this work, we developed a porous negative triboelectric material by synthesizing ZIF-8 on the surface of a cellulose/graphene oxide aerogel, grafting it with trimethoxy(1H,1H,2H,2H-heptadecafluorodecyl)silane, and adding a negative corona treatment, and it was combined with a positive triboelectric material to create a cellulose nanofiber-based TENG self-powered filter. The devices achieved a balance between a small pressure drop (53 Pa) and high filtration efficiency (98.97%, 99.65%, and 99.93% for PM0.3, PM0.5, and PM1, respectively), demonstrating robust filtration properties at high temperatures and high humidities. Our work provides a new approach for developing self-powered wearable healthcare devices with excellent air filtration properties.

Rapid Thermochromic and Highly Thermally Conductive Nanocomposite Based on Silicone Rubber for Temperature Visualization Thermal Management in Electronic Devices

Effective heat dissipation and real-time temperature monitoring are crucial for ensuring the long-term stable operation of modern, high-performance electronic products. This study proposes a silicon rubber polydimethylsiloxane (PDMS)-based nanocomposite with a rapid thermal response and high thermal conductivity. This nanocomposite enables both rapid heat dissipation and real-time temperature monitoring for high-performance electronic products. The reported material primarily consists of a thermally conductive layer (Al2O3/PDMS composites) and a reversible thermochromic layer (organic thermochromic material, graphene oxide, and PDMS nanocoating; OTM-GO/PDMS). The thermal conductivity of OTM-GO/Al2O3/PDMS nanocomposites reached 4.14 W m-1 K-1, reflecting an increase of 2200% relative to that of pure PDMS. When the operating temperature reached 35, 45, and 65 °C, the surface of OTM-GO/Al2O3/PDMS nanocomposites turned green, yellow, and red, respectively, and the thermal response time was only 30 s. The OTM-GO/Al2O3/PDMS nanocomposites also exhibited outstanding repeatability and maintained excellent color stability over 20 repeated applications.

Engineering surgical face masks with photothermal and photodynamic plasmonic nanostructures for enhancing filtration and on-demand pathogen eradication

The shortage of face masks and the lack of antipathogenic functions has been significant since the recent pandemic's inception. Moreover, the disposal of an enormous number of contaminated face masks not only carries a significant environmental impact but also escalates the risk of cross-contamination. This study proposes a strategy to upgrade available surgical masks into antibacterial masks with enhanced particle and bacterial filtration. Plasmonic nanoparticles can provide photodynamic and photothermal functionalities for surgical masks. For this purpose, gold nanorods act as on-demand agents to eliminate pathogens on the surface of the masks upon near-infrared light irradiation. Additionally, the modified masks are furnished with polymer electrospun nanofibrous layers. These electrospun layers can enhance the particle and bacterial filtration efficiency, not at the cost of the pressure drop of the mask. Consequently, fabricating these prototype masks could be a practical approach to upgrading the available masks to alleviate the environmental toll of disposable face masks.

Antibiotic-Loaded Boron Nitride Nanoconjugate with Strong Performance against Planktonic Bacteria and Biofilms

Protecting surfaces from biofilm formation presents a significant challenge in the biomedical field. The utilization of antimicrobial component-conjugated nanoparticles is becoming an attractive strategy against infectious biofilms. Boron nitride (BN) nanomaterials have a unique biomedical application value due to their excellent biocompatibility. Here, we developed antibiotic-loaded BN nanoconjugates to combat bacterial biofilms. Antibiofilm testing included two types of pathogens, Staphylococcus aureus and Escherichia coli. Gentamicin was loaded on polydopamine-modified BN nanoparticles (GPBN) to construct a nanoconjugate, which was very effective in killing E. coli and S. aureus planktonic cells. GPBN exhibited equally strong capacity for biofilm destruction, tested on preformed biofilms. A 24 h treatment with the nanoconjugate reduced cell viability by more than 90%. Our results suggest that GPBN adheres to the surface of the biofilm, penetrates inside the biofilm matrix, and finally deactivates the cells. Interestingly, the GPBN coatings also strongly inhibited the formation of bacterial biofilms. Based on these results, we suggest that GPBN could serve as an effective means for treating biofilm-associated infections and as coatings for biofilm prevention.

Nano-copper ions assembled cellulose-based composite with antibacterial activity for biodegradable personal protective mask

The current SARS-CoV-2 pandemic has resulted in the widespread use of personal protective equipment, particularly face masks. However, the use of commercial disposable face masks puts great pressure on the environment. In this study, nano-copper ions assembled cotton fabric used in face masks to impart antibacterial activity has been discussed. To produce the nanocomposite, the cotton fabric was modified by sodium chloroacetate after its mercerization, and assembled with bactericidal nano-copper ions (about 10.61 mg·g-1) through electrostatic adsorption. It demonstrated excellent antibacterial activity against Staphylococcus aureus and Escherichia coli because the gaps between fibers in the cotton fabric allow the nano-copper ions to be fully released. Moreover, the antibacterial efficiency was maintained even after 50 washing cycles. Furthermore, the face mask constructed with this novel nanocomposite upper layer exhibited a high particle filtration efficiency (96.08% ± 0.91%) without compromising the air permeability (28.9 min·L-1). This green, economical, facile, and scalable process of depositing nano-copper ions onto modified cotton fibric has great potential to reduce disease transmission, resource consumption, and environmental impact of waste, while also expanding the range of protective fabrics.

Electrospun Nanocomposite Fibrous Membranes for Sustainable Face Mask Based on Triboelectric Nanogenerator with High Air Filtration Efficiency

Abstract

Air pollution caused by the rapid development of industry has always been a great issue to the environment and human being's health. However, the efficient and persistent filtration to PM0.3 remains a great challenge. Herein, a self-powered filter with micro-nano composite structure composed of polybutanediol succinate (PBS) nanofiber membrane and polyacrylonitrile (PAN) nanofiber/polystyrene (PS) microfiber hybrid mats was prepared by electrospinning. The balance between pressure drop and filtration efficiency was achieved through the combination of PAN and PS. In addition, an arched TENG structure was created using the PAN nanofiber/PS microfiber composite mat and PBS fiber membrane. Driven by respiration, the two fiber membranes with large difference in electronegativity achieved contact friction charging cycles. The open-circuit voltage of the triboelectric nanogenerator (TENG) can reach to about 8 V, and thus the high filtration efficiency for particles was achieved by the electrostatic capturing. After contact charging, the filtration efficiency of the fiber membrane for PM0.3 can reach more than 98% in harsh environments with a PM2.5 mass concentration of 23,000 µg/m3, and the pressure drop is about 50 Pa, which doesn't affect people's normal breathing. Meanwhile, the TENG can realize self-powered supply by continuously contacting and separating the fiber membrane driven by respiration, which can ensure the long-term stability of filtration efficiency. The filter mask can maintain a high filtration efficiency (99.4%) of PM0.3 for 48 consecutive hours in daily environments.

Graphical abstract

Supplementary Information

The online version contains supplementary material available at 10.1007/s42765-023-00299-z.

Antibacterial, UV-Protective, Hydrophobic, Washable, and Heat-Resistant BN-Based Nanoparticle-Coated Textile Fabrics: Experimental and Theoretical Insight

The use of nanoparticles (NPs) to modify the surface of cotton fabric is a promising approach to endowing the material with a set of desirable characteristics that can significantly expand the functionality, wear comfort, and service life of textile products. Herein, two approaches to modifying the surface of hexagonal boron nitride (h-BN) NPs with a hollow core and a smooth surface by treatment with maleic anhydride (MA) and diethylene triamine (DETA) were studied. The DETA and MA absorption on the surface of h-BN and the interaction of surface-modified h-NPs with cellulose as the main component of cotton were modeled using density functional theory with the extended Perdew-Burke-Ernzerhof functional. Theoretical modeling showed that the use of DETA as a binder agent can increase the adhesion strength of BN NPs to textile fabric due to the simultaneous hydrogen bonds with cellulose and BN. Due to the difference in zeta potentials (-38.4 vs -25.8 eV), MA-modified h-BN NPs form a stable suspension, while DETA-modified BN NPs tend to agglomerate. Cotton fabric coated with surface-modified NPs exhibits an excellent wash resistance and high hydrophobicity with a water contact angle of 135° (BN-MA) and 146° (BN-DETA). Compared to the original textile material, treatment with MA- and DETA-modified h-BN NPs increases heat resistance by 10% (BN-MA fabric) and 15% (BN-DETA fabric). Cotton fabrics coated with DETA- and MA-modified BN NPs show enhanced antibacterial activity against Escherichia coli U20 and Staphylococcus aureus strains and completely prevent the formation of an E. coli biofilm. The obtained results are important for the further development of fabrics for sports and medical clothing as well as wound dressings.

Polymeric Materials as Indispensable Tools to Fight RNA Viruses: SARS-CoV-2 and Influenza A

Towards the end of 2019 in Wuhan, suspicions of a new dangerous virus circulating in the air began to arise. It was the start of the world pandemic coronavirus disease 2019 (COVID-19). Since then, considerable research data and review papers about this virus have been published. Hundreds of researchers have shared their work in order to achieve a better comprehension of this disease, all with the common goal of overcoming this pandemic. The coronavirus is structurally similar to influenza A. Both are RNA viruses and normally associated with comparable infection symptoms. In this review, different case studies targeting polymeric materials were appraised to highlight them as an indispensable tool to fight these RNA viruses. In particular, the main focus was how polymeric materials, and their versatile features could be applied in different stages of viral disease, i.e., in protection, detection and treatment.

Research on the Anti-Risk Mechanism of Mask Green Supply Chain from the Perspective of Cooperation between Retailers, Suppliers, and Financial Institutions

Against the background of the pandemic, the mask supply chain faces the risk of pollution caused by discarded masks, the risk of insufficient funds of retailers, and the risk of mask overstock. To better guard against the above risks, this study constructed a two-party game model and a cusp catastrophe model from the perspective of the mask green supply chain, and studied the strategic choices of retailers and suppliers in the supply chain affected by the risk of capital constraints and overstock. The result shows that the risk shocks will lead to the disruption of the mask green supply chain, and the main factors affecting the strategy choice of mask suppliers and retailers are mask recycling rate, deposit ratio, risk occurrence time, etc. In further research, this study involved a mechanism for financial institutions, mask retailers, and the government to jointly deal with the risk of mask overstock, the risk of retailers' insufficient funds, and the risk of environmental pollution from discarded masks. The research path and conclusion of this study reveal the risks in the circulation area of mask supplies during the pandemic, and provide recommendations for planning for future crises and risk prevention.

Nanotechnology Transition Roadmap toward Multifunctional Stimuli-Responsive Face Masks

In recent times, the use of personal protective equipment, such as face masks or respirators, is becoming more and more critically important because of common pollution; furthermore, face masks have become a necessary element in the global fight against the COVID-19 pandemic. For this reason, the main mission of scientists has become the development of face masks with exceptional properties that will enhance their performance. The versatility of electrospun polymer nanofibers has determined their suitability as a material for constructing "smart" filter media. This paper provides an overview of the research carried out on nanofibrous filters obtained by electrospinning. The progressive development of the next generation of face masks whose unique properties can be activated in response to a specific external stimulus is highlighted. Thanks to additional components incorporated into the fiber structure, filters can, for example, acquire antibacterial or antiviral properties, self-sterilize the structure, and store the energy generated by users. Despite the discovery of several fascinating possibilities, some of them remain unexplored. Stimuli-responsive filters have the potential to become products of large-scale availability and great importance to society as a whole.

Recent Progress in Fabrication and Application of BN Nanostructures and BN-Based Nanohybrids

Due to its unique physical, chemical, and mechanical properties, such as a low specific density, large specific surface area, excellent thermal stability, oxidation resistance, low friction, good dispersion stability, enhanced adsorbing capacity, large interlayer shear force, and wide bandgap, hexagonal boron nitride (h-BN) nanostructures are of great interest in many fields. These include, but are not limited to, (i) heterogeneous catalysts, (ii) promising nanocarriers for targeted drug delivery to tumor cells and nanoparticles containing therapeutic agents to fight bacterial and fungal infections, (iii) reinforcing phases in metal, ceramics, and polymer matrix composites, (iv) additives to liquid lubricants, (v) substrates for surface enhanced Raman spectroscopy, (vi) agents for boron neutron capture therapy, (vii) water purifiers, (viii) gas and biological sensors, and (ix) quantum dots, single photon emitters, and heterostructures for electronic, plasmonic, optical, optoelectronic, semiconductor, and magnetic devices. All of these areas are developing rapidly. Thus, the goal of this review is to analyze the critical mass of knowledge and the current state-of-the-art in the field of BN-based nanomaterial fabrication and application based on their amazing properties.

A pandemic-induced environmental dilemma of disposable masks: solutions from the perspective of the life cycle

The coronavirus disease 2019 (COVID-19) has swept the world and still afflicts humans. As an effective means of protection, wearing masks has been widely adopted by the general public. The massive use of disposable masks has raised some emerging environmental and bio-safety concerns: improper handling of used masks may transfer the attached pathogens to environmental media; disposable masks mainly consist of polypropylene (PP) fibers which may aggravate the global plastic pollution; and the risks of long-term wearing of masks are elusive. To maximize the utilization and minimize the risks, efforts have been made to improve the performance of masks (e.g., antivirus properties and filtration efficiency), extend their functions (e.g., respiration monitoring and acting as a sampling device), develop new disinfection methods, and recycle masks. Despite that, from the perspective of the life cycle (from production, usage, and discard to disposal), comprehensive solutions are urgently needed to solve the environmental dilemma of disposable masks in both technologies (e.g., efficient use of raw materials, prolonging the service life, and enabling biodegradation) and policies (e.g., stricter industry criteria and garbage sorting).

Flexible silicone rubber/carbon fiber/nano-diamond composites with enhanced thermal conductivity via reducing the interface thermal resistance

Insulating materials with heat dissipation are urgently required for modern electronic devices and systems. In this study, 4,4-methylene diphenyl diisocyanate was used as the coupling agent, and nano-diamond (ND) particles were grafted onto the surface of carbon fibers (CFs) to prepare CF-ND/silicone rubber (SR) composites. The ND acted as a “bridge” among CFs, which can reduce the interface thermal resistance between CFs because the dot-like ND can increase the interfacial area of CFs, making it easier to form heat-conducting networks between SR. When the content of CF-ND (1:6) was 20%, the thermal conductivity of the SR composite was 0.305 W/(m·K), 69% higher than that of pure SR. The ND between CFs can improve the dynamic mechanical properties by acting as a crack pinhole. In addition, the CF-ND/SR composites also exhibited excellent thermal stability. This work has enormous potential for advanced electronic devices.

Temperature-adjustable F-carbon nanofiber/carbon fiber nanocomposite fibrous masks with excellent comfortability and anti-pathogen functionality

Wearing surgical masks remains the most effective protective measure against COVID-19 before mass vaccination, but insufficient comfortability and low antibacterial/antiviral activities accelerate the replacement frequency of surgical masks, resulting in large amounts of medical waste. To solve this problem, we report new nanofiber membrane masks with outstanding comfortability and anti-pathogen functionality prepared using fluorinated carbon nanofibers/carbon fiber (F-CNFs/CF). This was used to replace commercial polypropylene (PP) nonwovens as the core layer of face masks. The through-plane and in-plane thermal conductivity of commercial PP nonwovens were only 0.12 and 0.20 W/m K, but the F-CNFs/CF nanofiber membranes reached 0.62 and 5.23 W/m K, which represent enhancements of 380% and 2523%, respectively. The surface temperature of the PP surgical masks was 23.9 ℃ when the wearing time was 15 min, while the F-CNFs/CF nanocomposite fibrous masks reached 27.3 ℃, displaying stronger heat dissipation. Moreover, the F-CNFs/CF nanofiber membranes displayed excellent electrical conductivity and produced a high-temperature layer that killed viruses and bacteria in the masks. The surface temperature of the F-CNFs/CF nanocomposite fibrous masks reached 69.2 ℃ after being connected to a portable power source for 60 s. Their antibacterial rates were 97.9% and 98.6% against E. coli and S. aureus, respectively, after being connected to a portable power source for 30 min.

Eco-friendly chitosan@silver/plant fiber membranes for masks with thermal comfortability and self-sterilization

The surgical masks have been essential consumables for public in the COVID-19 pandemic. However, long-time wearing masks will make wearers feel uncomfortable and massive discarded non-biodegradable masks lead to a heavy burden on our environment. In this paper, we adopt degradable chitosan@silver (CS@Ag) core-shell fibers and plant fibers to prepare an eco-friendly mask with excellent thermal comfort, self-sterilization, and antiviral effects. The thermal network of CS@Ag core-shell fibers highly improves the in-plane thermal conductivity of masks, which is 4.45 times higher than that of commercial masks. Because of the electrical conductivity of Ag, the fabricated mask can be electrically heated to warm the wearer in a cold environment and disinfect COVID-19 facilely at room temperature. Meanwhile, the in-situ reduced silver nanoparticles (AgNPs) endow the mask with superior antibacterial properties. Therefore, this mask shows a great potential to address the urgent need for a thermally comfortable, antibacterial, antiviral, and eco-friendly mask.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10570-022-04582-x.

Masks for COVID-19

Sustainable solutions on fabricating and using a face mask to block the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) spread during this coronavirus pandemic of 2019 (COVID-19) are required as society is directed by the World Health Organization (WHO) toward wearing it, resulting in an increasingly huge demand with over 4 000 000 000 masks used per day globally. Herein, various new mask technologies and advanced materials are reviewed to deal with critical shortages, cross-infection, and secondary transmission risk of masks. A number of countries have used cloth masks and 3D-printed masks as substitutes, whose filtration efficiencies can be improved by using nanofibers or mixing other polymers into them. Since 2020, researchers continue to improve the performance of masks by adding various functionalities, for example using metal nanoparticles and herbal extracts to inactivate pathogens, using graphene to make masks photothermal and superhydrophobic, and using triboelectric nanogenerator (TENG) to prolong mask lifetime. The recent advances in material technology have led to the development of antimicrobial coatings, which are introduced in this review. When incorporated into masks, these advanced materials and technologies can aid in the prevention of secondary transmission of the virus.

Biodegradable and multifunctional surgical face masks: A brief review on demands during COVID-19 pandemic, recent developments, and future perspectives

Providing the greater public with the current coronavirus (SARS-CoV-2) vaccines is time-consuming and research-intensive; intermediately, some essential ways to reduce the transmission include social distancing, personal hygiene, testing, contact tracing, and universal masking. The data suggests that universal masking, especially using multilayer surgical face masks, offers a powerful efficacy for indoor places. These layers have different functions including antiviral/antibacterial, fluid barrier, particulate and bacterial filtration, and fit and comfort. However, universal masking poses a serious environmental threat since billions of them are disposed on a daily basis; the current coronavirus disease (COVID-19) has put such demands and consequences in perspective. This review focuses on surgical face mask structures and classifications, their impact on our environment, some of their desirable functionalities, and the recent developments around their biodegradability. The authors believe that this review provides an insight into the fabrication and deployment of effective surgical face masks, and it discusses the utilization of multifunctional structures along with biodegradable materials to deal with future demands in a more eco-friendly fashion.

Toward nanotechnology-enabled face masks against SARS-CoV-2 and pandemic respiratory diseases

Wearing a face mask has become a necessity following the outbreak of the coronavirus (COVID-19) disease, where its effectiveness in containing the pandemic has been confirmed. Nevertheless, the pandemic has revealed major deficiencies in the ability to manufacture and ramp up worldwide production of efficient surgical-grade face masks. As a result, many researchers have focused their efforts on the development of low cost, smart and effective face covers. In this article, following a short introduction concerning face mask requirements, the different nanotechnology-enabled techniques for achieving better protection against the SARS-CoV-2 virus are reviewed, including the development of nanoporous and nanofibrous membranes in addition to triboelectric nanogenerators based masks, which can filter the virus using various mechanisms such as straining, electrostatic attraction and electrocution. The development of nanomaterials-based mask coatings to achieve virus repellent and sterilizing capabilities, including antiviral, hydrophobic and photothermal features are also discussed. Finally, the usability of nanotechnology-enabled face masks is discussed and compared with that of current commercial-grade N95 masks. To conclude, we highlight the challenges associated with the quick transfer of nanomaterials-enabled face masks and provide an overall outlook of the importance of nanotechnology in counteracting the COVID-19 and future pandemics.

Recent Progress in Modified Polymer-Based PPE in Fight Against COVID-19 and Beyond

The increasing concerns about human-health-related microbial infections and the need for the development of personal protective equipment (PPE) is becoming a major challenge. Because of their light weight and ease of processing, polymeric materials are widely used in designing and fabricating PPE that are being used by healthcare workers and the general population. Among the available PPEs, face masks have been widely developed from polymeric materials such as polypropylene, polycarbonate, and poly(ethylene terephthalate). However, currently, many of the face masks are not antimicrobial, which can pose a great risk for cross-infection as discarded masks can be a dangerous source of microbes. To prevent the spread of microbes, researchers have prompted the development of self-sterilizing masks that are capable of inactivating microbes via different mechanisms. Hence, this review provides a brief overview of the currently available antimicrobial-modified polymer-based PPE, and it mainly focuses on the different types of nanoparticles and other materials that have been embedded in different polymeric materials. The possibility of inhaling microplastics from wearing a face mask is also outlined, and the effects of various modifications on the health of face mask users are also explored. Furthermore, the effects of the disposed masks on the environment are underlined.

Virucidal and biodegradable specialty cellulose nonwovens as personal protective equipment against COVID-19 pandemic

•

Enable to instantly inactivate SARS-CoV-2 (>99.14%) and HCoV-229E (>98.83%).

•

Excellent growth inhibition (>99.51%) towards both E. coli and S. aureus.

•

Address the environmental concerns raised by non-biodegradable face masks.

•

Development of safe, comfortable, and biodegradable textiles for PPE.

•

A facile and scalable method to produce biocidal textiles for various applications.

Introduction

Face masks are regarded as effective Personal Protective Equipment (PPE) during the COVID-19 pandemic. However, the dominant polypropylene (PP)-based masks are devoid of antiviral/antibacterial activities and create enormous environmental burdens after disposal.

Objectives

Here we report a facile and potentially scalable method to fabricate biodegradable, breathable, and biocidal cellulose nonwovens (BCNWs) to address both environmental and hygienic problems of commercially available face masks.

Methods

TEMPO-oxidized cellulose nonwovens are rendered antiviral/antibacterial via covalent bonding with disinfecting polyhexamethylene guanidine or neomycin sulfate through carbodiimide coupling chemistry.

Results

The obtained results showed that the BCNWs have virucidal rate of >99.14%, bactericidal efficiency of >99.51%, no leaching-out effect, and excellent air permeability of >1111.5 mm s⁻¹. More importantly, the as-prepared BCNWs can inactivate SARS-CoV-2 instantly.

Conclusions

This strategy provides a new platform for the green fabrication of multifunctional cellulose nonwovens as scalable bio-protective layers with superior performance for various PPE in fighting COVID-19 or future pandemics. Additionally, replacing the non-biodegradable non-antimicrobial PP-based masks with the cellulose-based masks can reduce the plastic wastes and lower the greenhouse gas production from the incineration of disposed masks.

Characterization of Materials Used as Face Coverings for Respiratory Protection

Use of masks is a primary tool to prevent the spread of the novel COVID-19 virus resulting from unintentional close contact with infected individuals. However, detailed characterization of the chemical properties and physical structure of common mask materials is lacking in the current literature. In this study, a series of commercial masks and potential mask materials, including 3M Particulate Respirator 8210 N95, a material provided by Oak Ridge National Laboratory Carbon Fiber Technology Facility (ORNL/CFTF), and a Filti Face Mask Material, were characterized by a suite of techniques, including scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. Wetting properties of the mask materials were quantified by measurements of contact angle with a saliva substitute. Mask pass-through experiments were performed using a dispersed metal oxide nanoparticle suspension to model the SARS-CoV-2 virus, with quantification via spatially resolved X-ray fluorescence mapping. Notably, all mask materials tested provided a strong barrier against respiratory droplet breakthrough. The comparisons and characterizations provided in this study provide useful information when evaluating mask materials for respiratory protection.

Functionalized Masks: Powerful Materials against COVID-19 and Future Pandemics

The outbreak of COVID-19 revealed the vulnerability of commercially available face masks. Without having antibacterial/antiviral activities, the current masks act only as filtering materials of the aerosols containing microorganisms. Meanwhile, in surgical masks, the viral and bacterial filtration highly depends on the electrostatic charges of masks. These electrostatic charges disappear after 8 h, which leads to a significant decline in filtration efficiency. Therefore, to enhance the masks' protection performance, fabrication of innovative masks with more advanced functions is in urgent demand. This review summarizes the various functionalizing agents which can endow four important functions in the masks including i) boosting the antimicrobial and self-disinfectant characteristics via incorporating metal nanoparticles or photosensitizers, ii) increasing the self-cleaning by inserting superhydrophobic materials such as graphenes and alkyl silanes, iii) creating photo/electrothermal properties by forming graphene and metal thin films within the masks, and iv) incorporating triboelectric nanogenerators among the friction layers of masks to stabilize the electrostatic charges and facilitating the recharging of masks. The strategies for creating these properties toward the functionalized masks are discussed in detail. The effectiveness and limitation of each method in generating the desired properties are well-explained along with addressing the prospects for the future development of masks.

Enhanced Medical and Community Face Masks with Antimicrobial Properties: A Systematic Review

Face masks help to limit transmission of infectious diseases entering through the nose and mouth. Beyond reprocessing and decontamination, antimicrobial treatments could extend the lifetime of face masks whilst also further reducing the chance of disease transmission. Here, we review the efficacy of treatments pertaining antimicrobial properties to medical face masks, filtering facepiece respirators and non-medical face masks. Searching databases identified 2113 studies after de-duplication. A total of 17 relevant studies were included in the qualitative synthesis. Risk of bias was found to be moderate or low in all cases. Sixteen articles demonstrated success in avoiding proliferation (if not elimination) of viruses and/or bacteria. In terms of methodology, no two articles employed identical approaches to efficacy testing. Our findings highlight that antimicrobial treatment is a promising route to extending the life and improving the safety of face masks. In order to reach significant achievements, shared and precise methodology and reporting is needed.

Mask Design for Life in the Midst of COVID-19

Existing medical masks have various disadvantages, such as the environmental damage caused by disposable masks, the discomfort and poor ventilation caused by prolonged mask wearing, and the lack of aesthetic design in mass-produced masks. Thus, this study used quality function deployment, the fuzzy analytic hierarchy process, and fuzzy comprehensive evaluation to research, develop, and design masks. The aforementioned methods were also used to determine the ranking of design requirements. The following priority ranking of design requirements from most to least important was obtained: reducing discomfort at the contact between the mask and the skin (0.265), avoiding foul odor inside the mask (0.187), convenient cleaning and portability (0.166), good airtightness (0.152), suitable aesthetic design for wearing in public and on social occasions (0.130), and reducing waste (0.100). Experts evaluated mask designs, and their opinions were subject to fuzzy analysis. Specifically, 50% of the experts evaluated the designs to be “good” or “very good”. Only 29% of the experts rated the design results as “average”. Thus, the innovative mask designed in this study can meet the needs of users, overcome the drawbacks of existing masks, and provide a feasible solution for the current COVID-19 pandemic.

Protection, disinfection, and immunization for healthcare during the COVID-19 pandemic: Role of natural and synthetic macromolecules

The world is trying to improve public health while the outbreak of the COVID-19 is at its worst. So far, countless people have died from the COVID-19 disease and it is still a serious threat to human health. Synthetic and natural polymers are unavoidable materials in the healthcare sector. During the COVID-19 outbreak, diverse medical equipment and devices were designed and developed by using these macromolecules for the protection, disinfection, and immunization applications. Synthetic polymers such as polypropylene, polystyrene, poly(lactic acid), poly(ethylene terephthalate), and so forth have been successfully applied for the design and fabrication of diverse face masks, shields, anti-viral coatings, as well as diagnostic kits. Natural polymers having great features such as biodegradability and environmentally friendly are made from algae, plants, and animals. These polymers including sodium alginate, chitosan, cellulose, and gums have been shown a critical role in the fabrication of personal protective equipment, immunosensors, and anti-viral spray for control and fight against COVID-19. Besides, the problem of plastic waste can be solved by replacing them with natural polymers. This mini-review aims to show the application of polymer-based materials during the COVID-19 epidemic.

Ultrathin Polydopamine-Graphene Oxide Hybrid Coatings on Polymer Filters with Improved Filtration Performance and Functionalities

Thin polymer fiber mats, in particular those made of nonwoven polypropylene (PP) fibers, are extensively used for medical and industrial filtration. The recent pandemic has increased the demand for the fabrication of protective masks. The nonwoven PP filter has limitations in filtration efficiency and lacks advanced functionalities. Here, we propose a simple, effective, and low-cost method to functionalize PP filters and endow antimicrobial and photothermal properties. Our approach is based on the deposition of an ultrathin hybrid coating composed of graphene oxide (GO) and polydopamine on the surface of PP filters by spray-coating. The complementary properties and synergic effects of GO and polydopamine in the ultrathin coating improved the filtration efficiency of the PP filter by 20% with little change in pressure drop. Single component coatings did not result in similar improvements in performance. The ultrathin coating also makes the surface of the filter more hydrophilic with negative charges. The photothermal property of GO enables a rapid temperature increase of the surface-coated filter upon light irradiation for easy sterilization. Furthermore, cationic polymer brushes can be grafted to the ultrathin hybrid coating, which adds the highly desired antimicrobial property to the PP filters for their more effective protection against microorganisms.