Hyperbranched Polyethylenimine-Tethered Multiple Emulsion-Templated Hierarchically Macroporous Poly(acrylic acid)-Al2O3 Nanocomposite Beads for Water Purification

Highly Porous Polymer Beads Coated with Nanometer-Thick Metal Oxide Films for Photocatalytic Oxidation of Bisphenol A

Highly porous metal oxide-polymer nanocomposites are attracting considerable interest due to their unique structural and functional features. A porous polymer matrix brings properties such as high porosity and permeability, while the metal oxide phase adds functionality. For the metal oxide phase to perform its function, it must be fully accessible, and this is possible only at the pore surface, but functioning surfaces require controlled engineering, which remains a challenge. Here, highly porous nanocomposite beads based on thin metal oxide nanocoatings and polymerized high internal phase emulsions (polyHIPEs) are demonstrated. By leveraging the unique properties of polyHIPEs, i.e., a three-dimensional (3D) interconnected network of macropores, and high-precision of the atomic-layer-deposition technique (ALD), we were able to homogeneously coat the entire surface of the pores in polyHIPE beads with TiO2-, ZnO-, and Al2O3-based nanocoatings. Parameters such as nanocoating thickness, growth per cycle (GPC), and metal oxide (MO) composition were systematically controlled by varying the number of deposition cycles and dosing time under specific process conditions. The combination of polyHIPE structure and ALD technique proved advantageous, as MO-nanocoatings with thicknesses between 11 ± 3 and 40 ± 9 nm for TiO2 or 31 ± 6 and 74 ± 28 nm for ZnO and Al2O3, respectively, were successfully fabricated. It has been shown that the number of ALD cycles affects both the thickness and crystallinity of the MO nanocoatings. Finally, the potential of ALD-derived TiO2-polyHIPE beads in photocatalytic oxidation of an aqueous bisphenol A (BPA) solution was demonstrated. The beads exhibited about five times higher activity than nanocomposite beads prepared by the conventional (Pickering) method. Such ALD-derived polyHIPE nanocomposites could find wide application in nanotechnology, sensor development, or catalysis.

Lignin nanoparticles as co-stabilizers and modifiers of nanocellulose-based Pickering emulsions and foams

Nanocellulose is very hydrophilic, preventing interactions with the oil phase in Pickering emulsions. This limitation is herein addressed by incorporating lignin nanoparticles (LNPs) as co-stabilizers of nanocellulose-based Pickering emulsions. LNP addition decreases the oil droplet size and slows creaming at pH 5 and 8 and with increasing LNP content. Emulsification at pH 3 and LNP cationization lead to droplet flocculation and rapid creaming. LNP application for emulsification, prior or simultaneously with nanocellulose, favors stability given the improved interactions with the oil phase. The Pickering emulsions can be freeze-dried, enabling the recovery of a solid macroporous foam that can act as adsorbent for pharmaceutical pollutants. Overall, the properties of nanocellulose-based Pickering emulsions and foams can be tailored by LNP addition. This strategy offers a unique, green approach to stabilize biphasic systems using bio-based nanomaterials without tedious and costly modification procedures.

Supplementary Information

The online version contains supplementary material available at 10.1007/s10570-023-05399-y.

Biomimetic Polylactic Acid Electrospun Fibers Grafted with Polyethyleneimine for Highly Efficient Methyl Orange and Cr(VI) Removal

The rapid growth of industrialization has resulted in the release of large quantities of pollutants into the environment, especially dyes and heavy metals, which are environmentally hazardous for humans and animals. It is considered as the most promising and environmentally friendly route to develop green materials by using the green modification method, which has no negative impact on the environment. In this work, the green material of polylactic acid (PLA) was used as the substrate material, and a novel modification method of polydopamine (PDA)-assisted polyethyleneimine (PEI) grafting was developed. The electrospun PLA fibers are mainly composed of stereocomplex crystallites, which were achieved via the electrospinning of poly(l-lactic acid) and poly(d-lactic acid). The water-soluble PEI was grafted onto the PDA-modified PLA fibers through the glutaraldehyde-assisted cross-linking reaction. The prepared composite fibers can be degraded, which is environmentally friendly and meets the requirements of sustainable development. The potential application of such PLA composite fibers in wastewater treatment was intensively evaluated. The results show that at appropriate fabrication conditions (PDA concentration of 3 g·L^-1 and a PEI molecular weight of 70,000 g·mol^-1), the composite fibers exhibit the maximum adsorption capacities of 612 and 398.41 mg·g^-1 for methyl orange (MO) and hexavalent chromium [Cr(VI)], respectively. Simultaneously, about 64.79% of Cr(VI) adsorbed on the composite fibers was reduced to Cr(III). The above results show that the PLA composite fibers have a good development prospect in the field of wastewater treatment.

MOFs-alginate/polyacrylic acid/poly (ethylene imine) heparin-mimicking beads as a novel hemoadsorbent for bilirubin removal in vitro and vivo models

Metal-organic frameworks (MOFs) have a potential application in blood purification, but their microcrystalline nature has hampered their industrial application. Here, novel MOFs-polymer beads based on UiO, sodium alginate, polyacrylic acid, and poly (ethylene imine) were prepared and applied as a whole blood hemoadsorbent for the first time. The amidation among polymers immobilized UiO66-NH₂ into the network of the optimal product (SAP-3), and the NH₂ of UiO66-NH₂ significantly increased the removal rate (70 % within 5 min) of SAP-3 on bilirubin. The adsorption of SAP-3 on bilirubin mainly obeyed the pseudo-second-order kinetic, Langmuir isotherm and Thomas models with a maximum adsorption capacity (q_m) of 63.97 mg·g^-1. Experimental and density functional theory simulation results show that bilirubin was mainly adsorbed by UiO66-NH₂via electrostatic force, hydrogen bonding, and π-π interactions. Notably, the adsorption in vivo show that the total bilirubin removal rate in the whole blood of the rabbit model was up to 42 % after 1 h of adsorption. Given its excellent stability, cytotoxicity, and hemocompatibility, SAP-3 has a great potential in hemoperfusion therapy. This study proposes an effective strategy for settling the powder property of MOFs and could provide experimental and theoretical references for application of MOFs in blood purification.

Polydopamine-assisted polyethylenimine grafting melamine foam and the application in wastewater purification

Melamine foam (MF) is a widely used commercial product and exhibits wide applications in many fields ranging from building, transportation to daily chemical product. Recent researches confirm that the special three-dimensional (3D) framework structure of MF can be an ideal substrate to prepare functional materials. In this work, the water-soluble polyethylenimine (PEI) was grafted onto the framework of MF to develop the water purification material toward heavy metal ions removal. The grafting of PEI on MF was achieved with the aids of polydopamine (PDA) coating and epoxy chloropropane (ECH) cross-linking successively. The 3D framework of MF could be well reserved and PEI was homogeneously grafted onto the framework surface. The adsorption capacity of the adsorbent was dependent upon the molecular wight of PEI. Lower PEI molecular weight endowed the adsorbent with better adsorption ability. The maximum adsorption capacity reached 328.95 mg/g, and the adsorbent exhibited extremely high adsorption stability with increasing cycling measurement numbers. Further results showed that the adsorbent also exhibited high reduction ability and induced about 62.5% toxic Cr(VI) to be reduced. This work confirms that the PEI-modified MF sample is a promising adsorbent in the removal of heavy metal ions and it can be used in wastewater treatment.

Fundamentals and Design-Led Synthesis of Emulsion-Templated Porous Materials for Environmental Applications

Emulsion templating is at the forefront of producing a wide array of porous materials that offers interconnected porous structure, easy permeability, homogeneous flow-through, high diffusion rates, convective mass transfer, and direct accessibility to interact with atoms/ions/molecules throughout the exterior and interior of the bulk. These interesting features together with easily available ingredients, facile preparation methods, flexible pore-size tuning protocols, controlled surface modification strategies, good physicochemical and dimensional stability, lightweight, convenient processing and subsequent recovery, superior pollutants remediation/monitoring performance, and decent recyclability underscore the benchmark potential of the emulsion-templated porous materials in large-scale practical environmental applications. To this end, many research breakthroughs in emulsion templating technique witnessed by the recent achievements have been widely unfolded and currently being extensively explored to address many of the environmental challenges. Taking into account the burgeoning progress of the emulsion-templated porous materials in the environmental field, this review article provides a conceptual overview of emulsions and emulsion templating technique, sums up the general procedures to design and fabricate many state-of-the-art emulsion-templated porous materials, and presents a critical overview of their marked momentum in adsorption, separation, disinfection, catalysis/degradation, capture, and sensing of the inorganic, organic and biological contaminants in water and air.