3D MXene Sponge: Facile Synthesis, Excellent Hydrophobicity, and High Photothermal Efficiency for Waste Oil Collection and Purification

FeOOH Quantum Dots Assembled MXene-Decorated 3D Photothermal Evaporator for Synergy Application in Solar Evaporation and Fenton Degradation

Solar-driven water evaporation is considered as the sustainable approach to alleviate freshwater resource crisis through direct use of solar energy. However, it is still challenging to achieve the multifunctional solar evaporators equipped with both high evaporation and purification performance to handle practical complex wastewater. Here, a simple and cost-effective multifunctional 3D solar evaporator is prepared by alternately decorating the commercial sponge with FeOOH quantum dots (FQDs) supported MXene sheets composites and chitosan hydrogel coatings for enabling the solar water evaporation and organic wastewater photodegradation simultaneously. MXene composites allow the solar evaporator with excellent photothermal conversion performance, the hydrophilic chitosan hydrogel coated interconnecting skeleton structures of sponge serve as the mass transfer and water transport channels. The Fenton-catalytic FQDs anchored on the MXene sheets surface accept the photo-generated electrons of MXene sheets to induce the organic pollutant photo-Fenton degradation reaction under sunlight irradiation. The resulting evaporator possesses both excellent water evaporation rate of 2.54 kg m-2 h-1 and high degradation efficiency (99.24% for methylene blue), coupled with durable salt-resisting performance during long-term seawater desalination (20 wt.% NaCl). This work provides a simple and feasible strategy for designing multifunctional solar evaporators to meet the potential application scenarios in practice.

A disposable ultrasensitive immunosensor based on MXene/NH2-CNT modified screen-printed electrode for the detection of ovarian cancer antigen CA125

Cancer antigen 125 (CA125) is the gold standard biomarker for clinical diagnosis of ovarian cancer, with a threshold value of 35 U/mL in serum. In this paper, a disposable ultrasensitive immunosensor based on Ti3C2Tx-MXene/amino-functionalized carbon nanotube (NH2-CNT) modified screen-printed carbon electrode (SPCE) was constructed for the detection of the ovarian cancer antigen CA125. By optimizing the mass ratio of Ti3C2Tx to NH2-CNT, Ti3C2Tx/NH2-CNT composite with excellent electrochemical properties was prepared, which is beneficial for amplifying the initial electrochemical signal. The positively charged NH2-CNT effectively alleviated the stacking problem of Ti3C2Tx, and its amino group also facilitated the covalent immobilization of the capture antibody. Meanwhile, chitosan (CS) with excellent film-forming ability was also used to successfully enhance the adsorption of electrode material, thus improving the stability of the sensor. In addition, CS could further enhance the current signal. The prepared immunosensor exhibited excellent performance in CA125 detection with a wide linear range from 1 mU/mL to 500 U/mL, and good selectivity, reproducibility and lomg-term stability. Furthermore, the immunosensor showed satisfactory results for the detection of CA125 in clinical serum samples, which is promising for the clinical screening, early diagnosis and prognostic examination of ovarian cancer.

Applications of three-dimensional whey protein amyloid fibril-based hybrid aerogels in oil/water separation and emulsion separation

Environmental contamination from oil spills and industrial wastewater poses long-term risks to ecosystems and human health. Amyloid fibrils' superior stiffness and stability, outstanding biocompatibility and biodegradability, versatile functional groups, and high specific surface area make them promising sustainable adsorbents. This study is aimed at examining the application of three-dimensional polysaccharide-modified whey protein amyloid fibril (WPIAF) aerogels in oil/water separation and emulsion separation. The WPIAF aerogel was first synthesized through the salting out method coupled with lyophilization, then modified using carboxymethyl cellulose (CMC) or chitosan (CS). Our results showed that WPIAF aerogels exhibited increased mechanical properties and surface hydrophobicity after polysaccharide modification. The CS-modified WPIAF aerogels showed better oil adsorption capacities, oil adsorption capability, and reusability than WPIAF aerogel and CMC-modified WPIAF aerogels. Furthermore, the applicability of polysaccharide-modified WPIAF aerogels in a continuous oil/water separation system was demonstrated. Finally, the separation efficiencies of polysaccharide-modified WPIAF aerogels were determined to be over 90 % in various emulsion systems, and the possible separation mechanism was further investigated. This study provides a nice example of applying amyloid-based aerogels for oil/water separation and emulsion separation.

Superhydrophobic Solar-to-Thermal Materials Toward Cutting-Edge Applications

Solar-to-thermal conversion is a direct and effective way to absorb sunlight for heat via the rational design and control of photothermal materials. However, when exposed to water-existed conditions, the conventional solar-to-thermal performance may experience severe degradation owing to the high specific heat capacity of water. To tackle with the challenge, the water-repellent function is introduced to construct superhydrophobic solar-to-thermal materials (SSTMs) for achieving stable heating, and even, for creating new application possibilities under water droplets, sweat, seawater, and ice environments. An in-depth review of cutting-edge research of SSTMs is given, focusing on synergetic functions, typical construction methods, and cutting-edge potentials based on water medium. Moreover, the current challenges and future prospects based on SSTMs are also carefully discussed.

Novel 2D MXene Cobalt Ferrite (CoF@Ti3C2) Composite: A Promising Photothermal Anticancer In Vitro Study

In search of materials with superior capability of light-to-heat (photothermal) conversion, biocompatibility, and confinement of active photothermal materials within the cells, novel magnetic MXene-based nanocomposites are found to possess all of these criteria. The CoF@Ti3C2 composite is fabricated by a simple two-step method, including an exfoliation strategy followed by sonochemical method. MXene composite has been modified with polyvinylpyrrolidone (PVP) to improve the stability in physiological conditions. The synthesized composite was characterized with multiple analytical tools. In vitro photothermal conversion efficiency of composite was determined by the time constant method and achieved η = 34.2% with an NIR 808 nm laser. In vitro, cytotoxicity studies conducted on human malignant melanoma (Ht144) and cells validated the photothermal property of the CoF@Ti3C2-PVP composite in the presence of an NIR laser (808 nm, 1.0 W cm-2), with significantly increased cytotoxicity. Calculated IC50 values were 86 μg/mL with laser, compared to 226 μg/mL without the presence of NIR laser. Microscopic results demonstrated increased apoptosis in the presence of NIR laser. Additionally, hemolysis assay confirmed biocompatibility of CoF@Ti3C2-PVP composite for intravenous applications at the IC50 concentration. The research described in this work expands the potential applications of MXene-based nanoplatforms in the biomedical field, particularly in photothermal therapy (PTT). Furthermore, the addition of cobalt ferrite serves as a magnetic nanocomposite, which eventually helps to confine therapeutic photothermal materials inside the cells, provides enhanced photothermal conversion efficiency, and creates externally controlled theranostic nanoplatforms for cancer therapy.

Facile Preparation of Photothermal Superhydrophobic Melamine Sponge Decorated with MXene and Lignin Particles for Efficient Oil/Water Separation, Fast Crude Oil Recovery, and Active Deicing

Frequent oil spills and the discharge of oily wastewaters have caused a serious threat to the environment, ecosystems, and human beings. Herein, a photothermal and superhydrophobic melamine sponge (MS) decorated with MXene and lignin particles has been prepared for the separation of oil/water mixtures, the recovery of crude oils, and active deicing. The obtained superhydrophobic melamine sponge shows a water contact angle (WCA) of 152.3° and an oil contact angle of ∼0° and possesses good chemical stability, thermal stability, and mechanical durability in terms of being immersed in various liquids (i.e., corrosive solutions, organic solvents, and boiling water) and being abrased by sandpapers. This superhydrophobic MS displays a high oil adsorption capacity of CCl4, up to 91.6 times its own weight and a high separation efficiency of 99.4%. Furthermore, the maximum surface temperature of the superhydrophobic MS reaches 57.5 °C under sunlight irradiation (1.0 kW/m2) due to the excellent photothermal heating conversion performance of MXene and lignin particles. When exposed to sunlight, the superhydrophobic MS can quickly absorb viscous crude oils up to 72 times its own weight. Also, the WCA of the superhydrophobic MS remains above 146° after 50 icing/deicing cycles, showing excellent photothermal anti-icing properties. Thus, this study presents an easy and low-cost method for designing photothermal superhydrophobic melamine sponges and opens a new avenue to the applications of efficient oil/water separation, fast crude oil recovery, and active deicing.

Effective separation of water-in-oil emulsions using an under-medium superlyophilic membrane with hierarchical pores

Separating water-in-oil emulsions is important in terms of environmental protection and resource recovery. To address the challenges posed by the water-oil interface, superwetting materials have been designed to accomplish separation through filtration and adsorption. Superhydrophobic membranes prevent the permeation of water droplets owing to extreme repellence and their size-sieving abilities. However, their use in remediating water-contaminated oil is limited by high oil viscosities. Meanwhile, in-air superhydrophilic sorbents are rarely employed for the separation of water-in-oil emulsions due to the thermodynamic and kinetic limitations of water adsorption in oil. Herein, the integration of an under-medium superlyophilic membrane with the hierarchical porous structure of wood is presented for filtration-driven selective adsorption of water from surfactant-stabilized (10 g/L) water-in-oil emulsions. Compared to filtration through a natural wood membrane or direct adsorption using an under-oil superhydrophilic wood membrane, the under-medium superlyophilic wood membrane demonstrated high separation efficiencies of > 99.95% even when applied to the regeneration of high-viscosity lubricating (6.3 mPa s) and edible (50.5 mPa s) oils, exhibiting viscosity-dependent fluxes and excellent stability. Moreover, the cost of purifying 200 mL of lubricating oil using the modified wood membrane was much lower than the oil's market price and required a low energy consumption of ca. 1.72 kWh. ENVIRONMENTAL IMPLICATION: The ever-growing use of petroleum and industrial/domestic oil products has led to excessive (estimated at a million tons per year) output of waste oils. Because direct discharge of waste oils into the environment causes serious pollution problems, separating water-in-oil emulsions is important in terms of environmental protection and resource recovery. Here filtration-driven water adsorption has been demonstrated to be a feasible method for the remediation of water-contaminated waste oils, even those that are highly viscous.

Janus Membrane with Intrafibrillarly Strontium-Apatite-Mineralized Collagen for Guided Bone Regeneration

Commercial collagen membranes face difficulty in guided bone regeneration (GBR) due to the absence of hierarchical structural design, effective interface management, and diverse bioactivity. Herein, a Janus membrane called SrJM is developed that consists of a porous collagen face to enhance osteogenic function and a dense face to maintain barrier function. Specifically, biomimetic intrafibrillar mineralization of collagen with strontium apatite is realized by liquid precursors of amorphous strontium phosphate. Polycaprolactone methacryloyl is further integrated on one side of the collagen as a dense face, which endows SrJM with mechanical support and a prolonged lifespan. In vitro experiments demonstrate that the dense face of SrJM acts as a strong barrier against fibroblasts, while the porous face significantly promotes cell adhesion and osteogenic differentiation through activation of calcium-sensitive receptor/integrin/Wnt signaling pathways. Meanwhile, SrJM effectively enhances osteogenesis and angiogenesis by recruiting stem cells and modulating osteoimmune response, thus creating an ideal microenvironment for bone regeneration. In vivo studies verify that the bone defect region guided by SrJM is completely repaired by newly formed vascularized bone. Overall, the outstanding performance of SrJM supports its ongoing development as a multifunctional GBR membrane, and this study provides a versatile strategy of fabricating collagen-based biomaterials for hard tissue regeneration.

Photothermal, Magnetic, and Superhydrophobic PU Sponge Decorated with a Fe3O4/MXene/Lignin Composite for Efficient Oil/Water Separation

Frequent oil spills and the discharge of industrial oily wastewaters have become a serious threat to the environment, ecosystem, and human beings. Herein, a photothermal, magnetic, and superhydrophobic PU sponge decorated with a Fe3O4/MXene/lignin composite (labeled as S-Fe3O4/MXene/lignin@PU sponge) has been designed and prepared. The obtained superhydrophobic/superoleophilic PU sponge possesses excellent chemical stability, thermal stability, and mechanical durability in terms of being immersed in corrosive solutions and organic solvents and boiling water and being abrased by sandpapers, respectively. The oil adsorption capacities of the S-Fe3O4/MXene/lignin@PU sponge for various organic liquids range from 29.1 to 70.3 g/g, and the oil adsorption capacity for CCl4 can remain 69.6 g/g even after 15 cyclic adsorption tests. The separation efficiencies of the S-Fe3O4/MXene/lignin@PU sponge for n-hexane and CCl4 are higher than 98% in different environments (i.e., water, hot water, 1 mol/L NaOH, 1 mol/L NaCl, and 1 mol/L HCl). More importantly, the introduction of three light absorbers (i.e., Fe3O4, MXene, and lignin) into the S-Fe3O4/MXene/lignin@PU sponge shows a synergistic effect in the photothermal heat conversion performance, and the maximum surface temperature reaches 64.4 °C under sunlight irradiation (1.0 kW/m2). The separation flux of the S-Fe3O4/MXene/lignin@PU sponge for viscous LT147 vacuum pump oil reaches 35,469 L m-2 h-1 under sunlight irradiation, showing an increase of 27.3% compared to that of oil adsorption processes without the photothermal effect. Thus, the rational design of superhydrophobic sponges by introducing proper photothermal heat absorbers provides new insights into facile and cost-effective preparation of sponges for efficient oil/water separation.

Transition metal compounds: From properties, applications to wettability regulation

Transition metal compounds (TMCs) have the advantages of abundant reserves, low cost, non-toxic and pollution-free, and have attracted wide attention in recent years. With the development of two-dimensional layered materials, a new two-dimensional transition metal carbonitride (MXene) has attracted extensive attention due to its excellent physicochemical properties such as gas selectivity, photocatalytic properties, electromagnetic interference shielding and photothermal properties. They are widely used in gas sensors, oil/water separation, wastewater and waste-oil treatment, cancer treatment, seawater desalination, strain sensors, medical materials and some energy storage materials. In this view, we aim to emphatically summarize MXene with their properties, applications and their wettability regulation in different applications. In addition, the properties of transition metal oxides (TMOs) and other TMCs and their wettability regulation applications are also discussed.

MXene/Graphene modified cellulose aerogel for photo-electro-assisted all-weather cleanup of high-viscous crude oil from spill

The frequent occurrence of oil spills has led to serious environmental pollution and ecological issues. Given the high-viscosity of crude oil, it is essential to develop sorbents with efficient viscosity reduction and sorption capacity in various environmental conditions. Herein, a superhydrophobic carboxymethyl cellulose (CMC) aerogel co-modified by MXene and graphene jointly (M-Mxene/Gr CA) with aligned channels structure was prepared. The aligned channels structure can effectively improve the longitudinal thermal conductivity and reduce the sorption resistance. Through the modification of MXene and graphene, the aerogel realized efficient photo/electro-thermal conversion, thus ensuring its adaption to various working environments. The rapid heat generation can significantly reduce the viscosity of crude oil, achieving rapid recovery. Under one sun illumination (1.0 kW/m2), the surface temperature of M-Mxene/Gr CA can reach 72.6 °C and its sorption capability for high-viscous crude oil reaches 18 g/g. Combining photo-thermal and electro-thermal (0.5 kW/m2 and 23 V), the average sorption rate of crude oil can reach 1.3 × 107 g m-3 s-1. Finally, we present a continuous sorption system to recover offshore oil spills under the assistance of a pump. This work provides a new option for tackling high-viscous offshore oil spills due to its environmental friendliness and fast sorption capacity.

Reusable, Stable, Efficient and Multifunctional Superhydrophobic and Oleophilic Polyurethane Sponge for Oil-Water Separation Prepared Using Discarded Composite Insulator

Oil spills and chemical leakages are a serious source of pollution in oceans and rivers, and have attracted worldwide attention. Many scientists are currently engaged in the development of oil-water separation technology. In this study, the umbrella skirt of a discarded silicone rubber insulator was utilized as feedstock, and polydimethylsiloxane (PDMS) was employed to immobilize the prepared powder (FXBW) onto a polyurethane (PU) sponge skeleton. Without any modifications using chemical reagents, a novel oil-water separation material, FXBW-PU, was developed, with a water contact angle of 155.3°. The FXBW-PU sponge exhibited an absorption capacity ranging from 11.79 to 26.59 g/g for various oils and organic solvents, while maintaining an excellent selective adsorption performance, even after undergoing ten compression cycles, due to its exceptional chemical and mechanical stability. With the assistance of a vacuum pump, the FXBW-PU sponge was utilized in a continuous separation apparatus, resulting in a separation efficiency exceeding 98.6% for various oils and organic solvents. The separation efficiency of n-hexane remains as high as 99.2% even after 10 consecutive separation cycles. Notably, the FXBW-PU sponge also separated the dichloromethane-in-water emulsions, which achieved the effect of purifying water. In summary, FXBW-PU sponge has great potential in the field of cleaning up oil/organic solvent contamination due to its low preparation cost, environmental friendliness and excellent performance.

Graphdiyne-Based All-Solid-State Passively Q-Switched Tm:YAP Laser at 2 μm

All-solid-state Tm lasers have a wider wavelength range and higher output power compared to other types of lasers. In this work, we demonstrate an all-solid-state, high repetition, Tm:YAP laser Q-switched by a graphdiyne (GDY) saturable absorber. The high-quality optical nonlinear material GDY, synthesized by a cross-coupling method, exhibits a strong nonlinear optical response. The application of GDY as a saturable absorber in the passively Q-switched (PQS) Tm:YAP of an all-solid-state laser has been realized with the shortest pulse duration of ~785 ns and repetition frequency of ~199.6 kHz at a central wavelength of 1985.8 nm. This represents the shortest pulse duration and the highest repetition frequency achieved from GDY in a solid-state Tm laser to date. Our work demonstrates the remarkable nonlinear optical properties of GDY, which holds promising potential in the field of optoelectronics.

Lead Monoxide Nanostructures for Nanophotonics: A Review

Black-phosphorus-analog lead monoxide (PbO), as a new emerging 2D material, has rapidly gained popularity in recent years due to its unique optical and electronic properties. Recently, both theoretical prediction and experimental confirmation have revealed that PbO exhibits excellent semiconductor properties, including a tunable bandgap, high carrier mobility, and excellent photoresponse performance, which is undoubtedly of great interest to explore its practical application in a variety of fields, especially in nanophotonics. In this minireview, we firstly summarize the synthesis of PbO nanostructures with different dimensionalities, then highlight the recent progress in the optoelectronics/photonics applications based on PbO nanostructures, and present some personal insights on the current challenges and future opportunities in this research area. It is anticipated that this minireview can pave the way to fundamental research on functional black-phosphorus-analog PbO-nanostructure-based devices to meet the growing demands for next-generation systems.

Facile fabrication of solar-heating and Joule-heating hyperelastic MXene-modified sponge for fast all-weather clean-up of viscous crude oil spill

Developing rational sorbent for viscous crude oil clean-up is still a daunting challenge, which requires rapid oil-uptake capability and scalable fabrication process. Herein, a heatable hydrophobic sponge sorbent (H-MXene/PVA/MS) with excellent light/Joule-heating performances was fabricated by a simple and feasible top-down approach. MXene nanosheets firmly coated on the substrate skeleton gave the sorbent outstanding ability to convert solar/electricity into heat rapidly due to the localized surface plasmon resonance (LSPR) effect and ultrahigh metallic conductivity. The surface temperature of H-MXene/PVA/MS could reach about 80 ℃ under 1.0 sun irradiation within 30 s and 125 ℃ under a low applying voltage of 6 V within 25 s. The rapid and sufficient heat generation on the sorbent would effectively warm the surrounding oil and accelerate its absorption. The oil absorption rate under 1.0 sun irradiation (1 kW/m²) improved about 41.5 times compared to the unheated sorbent. Moreover, the sorbent showed practical application potential in harsh environments due to its high coating firmness, durability, elasticity, and suitability for large-scale production and operations. Thus, the easily-prepared H-MXene/PVA/MS sorbent, which mainly focuses on solar-heating, supplemented by Joule-heating, provides an efficient and energy-efficient strategy for addressing large-scale viscous oil spill clean-up.

An elastic MOF/graphene aerogel with high photothermal efficiency for rapid removal of crude oil

Due to the frequent spill accidents during crude oil exploration and transport, to rapidly cleanup crude oil and eliminate the environmental pollution of oil spill is in high demand. In this work, a three-dimensional graphene aerogel (MEGA) with high elasticity, photothermal conversion capacity and adsorption capacity was prepared for rapid removal of crude oil. The results showed that the as-prepared MEGA exhibited a layered structure, the octahedral HKUST-1 nanoparticles and hydrophobic polydimethylsiloxane (PDMS) coatings were uniformly deposited on the surface. Such a hierarchical micro-nano porous structure not only improved the aerogel's hydrophobicity (water contact angle in air up to 152.7°), but also endowed it with strong oil adsorption capacity (41-118 times of its own weight). Especially, the MEGA showed excellent photothermal conversion capacity. Under light irradiation, its temperature raised to 80 ℃ from room temperature in 100 s. As a result, the adsorption for one drop of crude oil by MEGA was shortened from 5 h to 40 s, comparing with that in dark condition. In addition, the MEGA showed remarkable elasticity and mechanical stability, it could maintain more than 90% efficiency after 10 adsorption-compression cycles. This study suggests that the prepared MEGA has great potential for rapid removal of crude oil.

A super water-resistant MXene sponge flexible sensor for bifunctional sensing of physical and chemical stimuli

Flexible wearable sensors with multifunctional features have attracted great interest in various applications such as disease diagnosis, environmental detection and healthcare monitoring. However, it is still a challenge to achieve a multifunctional sensor with super water resistance without compromising the overall performance of the sensing material. Here, we developed a 3D bifunctional flexible sensor based on an MXene melamine sponge (MS) through a simple and effective ultrasonic mixing process and a further vacuum annealing process. The sensor is able to show excellent response to different stimuli, including pressure and humidity. The thermal annealing treatment allows MXene to adhere more firmly to the internal skeleton of the sponge, which does not easily fall off and improves the water resistance, thus achieving wearability and high sensitivity over a wide area. The T-MXene@MS sensor has a sensitivity of 9.97 kPa^-1 in the 5-15 kPa range, a fast response time (180 ms), and good stability at 4000 cycles, enabling accurate monitoring of human movement. The sensor has a rich porous structure while maintaining its inherent flexibility, which allows for long term testing of human respiration as well as the ability to respond quickly to dynamic changes in humidity, demonstrating excellent long-term stability for 40 days of humidity detection.

Emerging Xene-Related Nanostructures for Versatile Applications

Investigations into semiconductor nanomaterials from both an academic and industrial point of view are of great significance [...].

2D MXene Ti3C2T x nanosheets in the development of a mechanically enhanced and efficient antibacterial dental resin composite

The bacterial accumulation at the margins of dental resin composites is a main cause of secondary caries, which may further lead to prosthodontic failure. In this regard, this study for the first time incorporated 2D MXene Ti₃C₂T_x nanosheets (NSs) into epoxy resin at different mass ratios (0, 0.5, 1.0, and 2.0 wt%) by solution blending and direct curing for dental applications. Compared to the pure resin, the as-fabricated MXene/resin composite not only exhibited improved mechanical and abrasive results but also displayed gradually improved antibacterial activity with MXene loading which was further enhanced by illumination in natural light due to the high photothermal efficiency of MXene. In addition, the cytotoxicity result demonstrated that the MXene-modified resin did not cause severe damage to normal cells. This novel MXene/resin nanocomposite could pave the way for new designs for high-performance, multifunctional nanocomposites to effectively protect dental health in daily life.

Ultralight, Elastic, Hybrid Aerogel for Flexible/Wearable Piezoresistive Sensor and Solid-Solid/Gas-Solid Coupled Triboelectric Nanogenerator

Aerogels have been attracting wide attentions in flexible/wearable electronics because of their light weight, excellent flexibility, and electrical conductivity. However, multifunctional aerogel-based flexible/wearable electronics for human physiological/motion monitoring, and energy harvest/supply for mobile electronics, have been seldom reported yet. In this study, a kind of hybrid aerogel (GO/CNT HA) based on graphene oxide (GO) and carboxylated multiwalled carbon nanotubes (CMWCNTs) is prepared which can not only used as piezoresistive sensors for human motion and physiological signal detections, but also as high performance triboelectric nanogenerator (TENG) coupled with both solid-solid and gas-solid contact electrifications (CE). The repeatedly loading-unloading tests with 20 000 cycles exhibit its high and ultrastable piezoresistive sensor performances. Moreover, when the obtained aerogel is used as the electrode of a TENG, high electric output performance is produced due to the synergistic effect of solid-solid, and gas-solid interface CEs (3D electrification: solid-solid interface CE between the two solid electrification layers; gas-solid interface CE between the inner surface of GO/CNT HA and the air filled in the aerogel pores). This kind of aerogel promises good applications for human physiological/motion monitoring and energy harvest/supply in flexible/wearable electronics such as piezoresistive sensors and flexible TENG.

Superhydrophobic MXene Coating with Biomimetic Structure for Self-Healing Photothermal Deicing and Photoelectric Detector

Two-dimensional transition metal carbides (Ti₃C₂T_x MXene) have emerged as new candidates for applications in multifunctional devices owing to their outstanding performance. However, these electronic devices are easily disturbed by water, breakage, oxidation during use, and limited energy resources. To solve these problems, herein, inspired by nature, a novel superhydrophobic, healable photothermal deicing and photodetector (SHPP) with a "papillary structure" is successfully fabricated for the first time, by a simple layer-by-layer assembly spraying process with 0D/1D/2D nanomaterials. As a result, the superhydrophobic modified 2D MXene coating (FM coating) on the SHPP sensor exhibits outstanding self-cleaning, long-term durability (>20 days), as well as excellent photothermal deicing performances under near-infrared light. Meanwhile, the unique semiembedded nano-ZnO/1D silver nanowire supports the sensor with desirable photoelectric performance with UV light and a fast response time (∼1 s), and good cycle stability. Moreover, benefiting from the transparent self-healing substrate, the photothermal deicing and photodetector properties can be restored at room temperature. The bioinspired structures and function mechanisms offer SHPP sensors great potential for the utilization of clean light energy, sensing, self-cleaning, anti-icing, and so forth.

Bismuth Quantum Dot (Bi QD)/Polydimethylsiloxane (PDMS) Nanocomposites with Self-Cleaning and Antibacterial Activity for Dental Applications

In the oral microenvironment, bacteria colonies are easily aggregated on the tooth-restoration surface, in the manner of a biofilm, which usually consists of heterogeneous structures containing clusters of a variety of bacteria embedded in an extracellular matrix, leading to serious recurrent caries. In this contribution, zero-dimensional (0D) bismuth (Bi) quantum dots (QDs) synthesized by a facile solvothermal method were directly employed to fabricate a Bi QD/polydimethylsiloxane (PDMS)-modified tooth by simple curing treatment. The result demonstrates that the as-fabricated Bi QD/PDMS-modified tooth at 37 °C for 120 min not only showed significantly improved hydrophobic performance with a water contact angle of 103° and 115° on the tooth root and tooth crown, respectively, compared to that (~20° on the tooth root, and ~5° on the tooth crown) of the pristine tooth, but also exhibited excellent antibacterial activity against S. mutans, superior biocompatibility, and biosafety. In addition, due to the highly photothermal effect of Bi QDs, the antibacterial activity of the as-fabricated Bi QD/PDMS-modified tooth could be further enhanced under illumination, even at a very low power density (12 mW cm^-2). Due to the facile fabrication, excellent hydrophobicity, superior antibacterial activity, and biocompatibility and biosafety of the Bi QD/PDMS-modified tooth, it is envisioned that the Bi QD/PDMS-modified tooth with a fascinating self-cleaning and antibacterial performance can pave the way to new designs of versatile multifunctional nanocomposites to prevent secondary caries in the application of dental restoration.

Two-Dimensional Selenium Nanosheet-Based Sponges with Superior Hydrophobicity and Excellent Photothermal Performance

Photothermally assisted superhydrophobic materials play an important role in a variety of applications, such as oil purification, waste oil collection, and solar desalination, due to their facile fabrication, low-cost, flexibility, and tunable thermal conversion. However, the current widely used superhydrophobic sponges with photothermal properties are usually impaired by a high loading content of photothermal agents (e.g., gold or silver nanoparticles, carbon nanotubes), low photothermal efficiency, and require harmful processes for modification. Here, a one-pot, simple composite consisting of two-dimensional (2D) selenium (Se) nanosheets (NSs) and commercially used melamine sponge (MS) is rationally designed and successfully fabricated by a facile dip-coating method via physical adsorption between 2D Se NSs and MS. The loading content of 2D Se NSs on the skeleton of the MS can be well controlled by dipping cycle. The results demonstrate that after the modification of 2D Se NSs on the MS, the wettability transition from hydrophilicity to hydrophobicity can be easily achieved, even at a very low loading of 2D Se NSs, and the highly stable photothermal conversion of the as-fabricated composites can be realized with a maximum temperature of 111 ± 3.2 °C due to the excellent photothermal effect of 2D Se NSs. It is anticipated that this composite will afford new design strategies for multifunctional porous structures for versatile applications, such as high-performance solar desalination and photothermal sterilization.

Size-tunable bismuth quantum dots for self-powered photodetectors under ambient conditions

Although black phosphorus analogue, bismuthene, has been extensively investigated in recent years, yet the investigation into the photoelectronic devices is still in its infancy. In this contribution, uniform zero-dimensional (0D) bismuth (Bi) quantum dots (QDs) with different sizes were successfully synthesized by a simple solvothermal method. The as-synthesized 0D Bi QDs serve as working electrode materials by a direct deposition for photoelectrochemical (PEC)-type photodetection. The PEC results demonstrate that the as-fabricated 0D Bi QD-based electrode not only possess suitable self-powered broadband photoresponse, but also displays excellent photodetection performance. Under simulated light, the photocurrent density and photoresponsivity of the as-fabricated 0D Bi QD-based electrode can reach 2690 nA cm^-2, and 22.0μA W^-1, respectively. In addition, the as-prepared Bi QDs with the average diameter of 17 nm exhibit the best PEC photoresponse behavior in the studied size range of Bi QDs, mainly ascribed to the synergistic effect of suitable band gap and accessible active sites. It is anticipated that the uniform Bi QDs can be served as building blocks for a variety of photoelectronic devices, further expanding the application prospects of bismuthene, and can provide in-depth acknowledge on the performance optimization of monoelement Bi-based optical devices.

Superhydrophobic nanofibrous sponge with hierarchically layered structure for efficient harsh environmental oil-water separation

Oil leakage has posed serious threat to the environment, but still remain a great challenge to be solved especially for harsh environmental conditions. Herein, robust superhydrophobic nickel hydroxide grown by hydrothermal method and stearic acid modification on a blow-spun polyacrylonitrile (PAN)/Al₂O₃ nanofibrous sponge was proposed, so that the nickel hydroxide-modified polyacrylonitrile sponge (NPAS) was successfully obtained for efficient oil-water separation. The porous NPAS with a distinctive hierarchically layered structure, which exhibited excellent separation efficiency and mechanical elasticity. Due to its superhydrophobic and high porosity, the absorption capacity of NPAS could reach as high as 45 g g^-1. It could not only separate a series of oil-water mixture with a high steady flux of 12,413 L m^-2 h^-1 (dichloromethane-water), but also separate stabilized emulsions with a superior flux 2032 L m^-2 h^-1 (water-in-dichloromethane) under gravity, all of that with above 99.92% separation efficiencies, which was higher than that of the most reported sponges. Most importantly, its strong acid/alkali resistance enable it is suitable for hazardous materials treatment applications in harsh environmental conditions. This novel NPAS via facile large-scale blow-spinning provide an efficient strategy for oil-containing wastewater treatment and environmental protection.

Solar-Assisted Superhydrophobic MoS2/PDMS/MS Sponge for the Efficient Cleanup of Viscous Oil

Industrialization releases many high-viscosity oil pollutants into the environment, requiring a hydrophobic recyclable oil-absorbing material. Therefore, a self-heating and superhydrophobic melamine sponge (MS) by connecting polydimethylsiloxane (PDMS) was coated with functionalized molybdenum disulfide (MoS₂) nanosheets on a three-dimensional microstructure of a commercial MS (MoS₂/PDMS/MS) via a simple and low-cost dip-coating method. The prepared sponge showed a water contact angle of 151.8°, indicating that the modified sponge exhibited superhydrophobicity. Due to the addition of MoS₂, the modified sponge can convert light into heat, and its surface could be heated to 59.7 °C within 30 s. Because of the excellent MoS₂/PDMS/MS photothermal performance, the sponge could decrease the viscosity of the high-viscosity oil, absorbing the high-viscosity oil efficiently. After simultaneous thermal analysis and repeated compression tests, the modified sponge exhibited high thermochemical stability, mechanical property, and reusability. This superhydrophobic multifunctional sponge shows excellent potential for high-viscosity oil absorption.

Infrared Light Emission Devices Based on Two-Dimensional Materials

Two-dimensional (2D) materials have garnered considerable attention due to their advantageous properties, including tunable bandgap, prominent carrier mobility, tunable response and absorption spectral band, and so forth. The above-mentioned properties ensure that 2D materials hold great promise for various high-performance infrared (IR) applications, such as night vision, remote sensing, surveillance, target acquisition, optical communication, etc. Thus, it is of great significance to acquire better insight into IR applications based on 2D materials. In this review, we summarize the recent progress of 2D materials in IR light emission device applications. First, we introduce the background and motivation of the review, then the 2D materials suitable for IR light emission are presented, followed by a comprehensive review of 2D-material-based spontaneous emission and laser applications. Finally, further development directions and challenges are summarized. We believe that milestone investigations of 2D-material-based IR light emission applications will emerge soon, which are beneficial for 2D-material-based nano-device commercialization.

Superhydrophobic polyurethane sponge based on sepiolite for efficient oil/water separation

Massive oil leakage accidents and illegal discharge of oily wastewater have not just destroyed the sustainability of the ecological environment but caused permanent damage to marine ecosystems, which makes it urgent to handle it. In this paper, by means of sol-gel, micro-nan silica that grew from the surface of fibrous sepiolite was organically modified with 1 H, 1 H, 2 H, 2 H-perfluorodecyltriethoxysilane (PFDS). The superhydrophobic sepiolite/silica firmly attached to the surface of polyurethane sponge under the action of oily epoxy resin with strong adhesion. The sponge exhibited superhydrophobicity and excellent selective oil adsorption capacity (19.98-40 times of their own weight). More importantly, besides the effective separation of immiscible oil-water mixtures (the separation rate reached 98.72%), it could also efficiently separate oil with water and oil with salt solution emulsions. In addition, the sponges kept hydrophobic even after floating in extremely corrosive liquids for 20 h, showing a strong resistance to strong acidic as well as alkaline liquids. After 100 times of mechanical compression, the three-dimensional structure of sponge held still and the water contact angle was greater than 144°, demonstrating an excellent mechanical stability, which provided a reference for its practical application in oil-water separation.

Thermal Properties of MXenes and Relevant Applications

The properties and applications of MXenes (a family of layered transition metal carbides, nitrides, and carbonitrides) have aroused enormous research interests for a decade since the successful synthesis of few-layer transition metal carbides in 2011. Though MXenes, as the building blocks, have already been applied in various fields (such as wearable electronics) owing to the distinctive optical, mechanical and electrical properties, their thermal stability and intrinsic thermal properties were less thoroughly investigated compared to other characteristics in early reports. The pioneering theoretical prediction of the thermoelectric nature of MXenes was performed in 2013 while the first experiment-based report concerning the degradation behavior of the 2D structure at elevated temperatures in a controlled atmosphere was published in 2015, followed by numerous discoveries regarding the thermal properties of MXenes. Herein, after a brief description of the synthesis, this Review summarized the latest insights into the thermal stability and thermophysical properties of MXenes, and further associated these unique properties with relevant applications by multiple examples. Finally, current hurdles and challenges in this field were provided along with some advices on potential research directions in the future.

Tin Oxide (SnO2) Nanoparticles: Facile Fabrication, Characterization, and Application in UV Photodetectors

Tin oxide (SnO2) nanomaterials are of great interest in many fields such as catalytic, electrochemical, and biomedical applications, due to their low cost, suitable stability characteristics, high photosensitivity, etc. In this contribution, SnO2 NPs were facilely fabricated by calcination of tin (II) oxalate in air, followed by a liquid-phase exfoliation (LPE) method. Size-selected SnO2 NPs were easily obtained using a liquid cascade centrifugation (LCC) technique. The as-obtained SnO2 NPs displayed strong absorption in the UV region (~300 nm) and exhibited narrower absorption characteristics with a decrease in NP size. The as-fabricated SnO2 NPs were, for the first time, directly deposited onto a poly(ethylene terephthalate) (PET) film with a regular Ag lattice to fabricate a flexible working electrode for a photoelectrochemical (PEC)-type photodetector. The results demonstrated that the SnO2-NP-based electrode showed the strongest photoresponse signal in an alkaline electrolyte compared with those in neutral and acidic electrolytes. The maximum photocurrent density reached 14.0 μA cm−2, significantly outperforming black phosphorus nanosheets and black phosphorus analogue nanomaterials such as tin (II) sulfide nanosheets and tellurene. The as-fabricated SnO2 NPs with relatively larger size had better self-powered photoresponse performance. In addition, the as-fabricated SnO2-NP-based PEC photodetector exhibited strong cycling stability for on/off switching behavior under ambient conditions. It is anticipated that SnO2 nanostructures, as building blocks, can offer diverse availabilities for high-performance self-powered optoelectronic devices to realize a carbon-neutral or carbon-free environment.

Thermally Conductive and Superhydrophobic Polyurethane Sponge for Solar-Assisted Separation of High-Viscosity Crude Oil from Water

The rapid and effective separation of high-viscosity heavy crude oil from seawater is a worldwide challenge. Herein, an ultralow density, photothermal, superhydrophobic, and thermally conductive polyurethane/polyaniline/hexagonal boron nitride@Fe₃O₄/polyacrylic-oleic acid resin sponge (PU/PANI/h-BN@Fe₃O₄/AR) was fabricated with a water contact angle (WCA) of 158°, thermal conductivity of 0.76 W m^-1 K^-1, density of 0.038 g cm^-3, limited oxygen index (LOI) of 28.82%, and porosity of 97.97% and used for solar-assisted separation of high-viscosity crude oil from water. Photothermal components were composed of PANI and Fe₃O₄, while h-BN particles were used as thermally conductive and flame retardant fillers. Therefore, the illuminated sunlight irradiation on the modified sponge was converted to heat due to the activity of photothermal components. The produced heat was rapidly transferred to the environment due to the presence of h-BN for increasing the temperature of the high-viscosity crude oil and reducing oil viscosity that helped to promote its fluidity and effective absorption. The crude oil absorption capacity of this sponge increased from 4 to 57 g g^-1 under irradiation of a sunlight simulator (power: 1 sun: 1 kW m^-2) for 17 min due to oil viscosity reduction from 2.46 × 10⁴ to below 100 mPa s followed by an increase in the surface temperature from 26 to 89 °C. Also, the oil absorption capacity was evaluated in a static state (172 g g^-1 for chloroform), under different external magnetic fields (140.7 g g^-1 for gasoline), and in a continuous state, which was 65,100 times of its own weight in the gasoline filtration process. The PU/PANI/h-BN@Fe₃O₄/AR sponge exhibited excellent stability against 20 times of reusing, mechanical compression, abrasion, immersing in various pH solutions, seawater, and high temperature. In all, the results confirmed that the prepared sponge is an excellent absorbent for organic solvents and highly viscous crude oil in the absence and presence of sunlight irradiation.