Enhanced Activity for Hydrogen Evolution Reaction over CoFe Catalysts by Alloying with Small Amount of Pt

The breaking of charge symmetry at the M-site in octahedral units of KMF3 perovskite induces enhanced electrochemical nitrate reduction in ammonia

Electrochemical production of NH3 from NO3- offers a solution to the environmental issue of excess NO3- but is challenged by the lack of efficient, sensitive electrocatalysts with high NH3 yield rate and Faraday efficiency (FE). Herein, a medium-entropy perovskite fluoride (KMF3, M = Co/Ni/Fe/Ti) was prepared as efficient electrocatalysts to produce NH3 via the NO3- reduction reaction (NO3-RR). By introducing various transition metals at the M-sites, the charge distribution at the M-site octahedral units was adjusted to increase the disorder of KMF3, resulting in an optimized electronic structure with high intrinsic NO3-RR performance. The presence of different transition metals at the M-sites promoted electron transfer, which inhibited the Co 1s-3d transition and strengthened the CoF bond, leading to a decrease in crystal symmetry. Furthermore, owing to differences in valence state, electronegativity, and ionic radius, the coordination number was reduced, inducing the generation of a local twisted coordination environment. This was conducive to catalyst adsorption and the breaking of NO bonds. As a result, the KMF3 exhibited a high NH3 yield rate of 13.9 mg h-1 cm-2 with an NH3 FE close to 100 %. The developed medium-entropy KMF3 electrocatalysts have the potential to recover NH3 from nitrate wastewater.

Electrocatalytic biomass upgrading coupled with hydrogen evolution and CO2 reduction

Clean energy production and CO2 utilization have attracted increasing interest. Electrocatalysis represents an effective way to produce green hydrogen from water and reduce CO2 to valuable compounds. However, for either the hydrogen evolution reaction (HER) or the CO2 reduction reaction (CO2RR), the reaction efficiency is significantly limited by the slow kinetics of the oxygen evolution reaction (OER) at the anode, which consumes most of the input energy. Therefore, great efforts have been made to replace the OER with organic oxidation reactions at the anode to decrease the reaction energy barrier. Biomass has an advantage of broad source, and when it is employed as an OER alternative in the anode oxidation reactions, not only can the reduction reaction efficiency at the cathode including the HER and CO2RR be enhanced but high-value chemicals can also be obtained, representing an attractive OER alternative. This review comprehensively summarizes the recent achievements in electrocatalytic biomass upgrading coupled with the HER and CO2RR, cataloged based on the type of biomass. The design of electrocatalysts for such coupled reaction systems is discussed. Finally, the challenges and perspectives in the field of this energy-saving and value-added coupling system are provided to inspire more efforts in pushing forward the development of this field.

Enhancing Benzylamine Electro-Oxidation and Hydrogen Evolution Through in-situ Electrochemical Activation of CoC2O4 Nanoarrays

The sluggish anodic oxygen evolution reaction (OER) seriously restricts the overall efficiency of water splitting. Here, we present an environmentally friendly and efficient aniline oxidation (BOR) to replace the sluggish OER, accomplishing the co-production of H2 and high value-added benzonitrile (BN) at low voltages. Cobalt oxalates grown on cobalt foam (CoC2O4 ⋅ 2H2O/CF) are adopted as the pre-catalysts, which further evolve into working electrocatalysts active for BOR and HER via appropriate electrochemical activation. Thereinto, cyclic voltammetry activation at positive potentials is performed to reconstruct cobalt oxalate via extensive oxidation, resulting in enriched Co(III) species and nanoporous structures beneficial for BOR, while chronoamperometry at negative potentials is introduced for the cathodic activation toward efficient HER with obvious improvement. The two activated electrodes can be combined into a two-electrode system, which achieves a high current density of 75 mA cm-2 at the voltage of 1.95 V, with the high Faraday efficiencies of both BOR (90.0 %) and HER (90.0 %) and the satisfactory yield of BN (76.8 %).

WO3 Nanorods Decorated with Very Small Amount of Pt for Effective Hydrogen Evolution Reaction

The electrochemical hydrogen evolution reaction (HER) is one of the most promising green methods for the efficient production of renewable and sustainable H₂, for which platinum possesses the highest catalytic activity. Cost-effective alternatives can be obtained by reducing the Pt amount and still preserving its activity. The Pt nanoparticle decoration of suitable current collectors can be effectively realized by using transition metal oxide (TMO) nanostructures. Among them, WO₃ nanorods are the most eligible option, thanks to their high stability in acidic environments, and large availability. Herein, a simple and affordable hydrothermal route is used for the synthesis of hexagonal WO₃ nanorods (average length and diameter of 400 and 50 nm, respectively), whose crystal structure is modified after annealing at 400 °C for 60 min, to obtain a mixed hexagonal/monoclinic crystal structure. These nanostructures were investigated as support for the ultra-low-Pt nanoparticles (0.2-1.13 μg/cm²): decoration occurs by drop casting some drops of a Pt nanoparticle aqueous solution and the electrodes were tested for the HER in acidic environment. Pt-decorated WO₃ nanorods were characterized by performing scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), Rutherford backscattering spectrometry (RBS), linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and chronopotentiometry. HER catalytic activity is studied as a function of the total Pt nanoparticle loading, thus obtaining an outstanding overpotential of 32 mV at 10 mA/cm², a Tafel slope of 31 mV/dec, a turn-over frequency of 5 Hz at -15 mV, and a mass activity of 9 A/mg at 10 mA/cm² for the sample decorated with the highest Pt amount (1.13 μg/cm²). These data show that WO₃ nanorods act as excellent supports for the development of an ultra-low-Pt-amount-based cathode for efficient and low-cost electrochemical HER.

Ternary Copper Tungsten Sulfide (Cu2WS4) Nanoparticles Obtained through a Solvothermal Approach: A Bi-Functional Electrocatalyst for the Hydrogen Evolution Reaction (HER) and Oxygen Evolution Reaction (OER)

In this work, Cu2WS4 nanoparticles have been synthesized via a solvothermal decomposition approach using a heterobimetallic single source precursor, WCu2S4(PPh3)3. The single source precursor, WCu2S4(PPh3)3, has been characterized using multinuclear NMR spectroscopy, while Cu2WS4 nanoparticles have been characterized by powder X-ray diffraction (PXRD) for which Rietveld refinement has been performed to authenticate the lattice structure of the decomposed product, Cu2WS4. Furthermore, FESEM and EDAX analyses have been performed to assess the morphology and composition of Cu2WS4. An electrochemical study in acidic as well as basic media suggested that Cu2WS4 nanoparticles possess efficient bifunctional activity towards electrochemical hydrogen as well as oxygen evolution reactions. Linear sweep voltammetry (LSV) performed in 0.5 N H2SO4 indicates an onset potential for the HER of 462 mV and a Tafel slope of 140 mV dec-1. While LSV performed in 0.1 M KOH indicates an onset potential for the OER of 190 mV and a Tafel Slope of 117 mV dec-1.

Metal-organic frameworks as a good platform for the fabrication of multi-metal nanomaterials: design strategies, electrocatalytic applications and prospective

MOF-derived multi-metal nanomaterials are attracting numerous attentions in widespread applications such as catalysis, sensors, energy storage and conversion, and environmental remediation. Compared to the monometallic counterparts, the presence of foreign metal is expected to bring new physicochemical properties, thus exhibiting synergistic effect for enhanced performance. MOFs have been proved as a good platform for the fabrication of polymetallic nanomaterials with requisite features. Herein, various design strategies related to constructing multi-metallic nanomaterials from MOFs are summarized for the first time, involving metal nodal substitution, seed epitaxial growth, ion-exchange strategy, guest species encapsulation, solution impregnation and combination with extraneous substrate. Afterwards, the recent advances of multi-metallic nanomaterials for electrocatalytic applications, including oxygen reduction reaction (ORR), oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), are systematically discussed. Finally, a personal outlook on the future trends and challenges are also presented with hope to enlighten deeper understanding and new thoughts for the development of multi-metal nanomaterials from MOFs.

Single source precursor route for the first graphene oxide-Pd6P nanocomposite: application in electrochemical hydrogen evolution reaction

For the first time, Pd₆P has been synthesised using a simple, straightforward and one-pot method i.e., thermolysis of a Pd(II) complex of a bidentate (P, N) organophosphorus ligand (anthracene-9-yl-CHN-CH₂CH₂-PPh₂). The electrocatalyst (obtained after grafting nanospheres of Pd₆P over layers of graphene oxide) shows high activity in electrochemical hydrogen evolution reactions (HER) with an overpotential of 133 mV to drive 10 mA cm^-2 of cathodic current density. The GO-Pd₆P nanocomposite is robust and effective for a continuous HER run for up to 16 hours.

Bimetallic Nanocrystals: Structure, Controllable Synthesis and Applications in Catalysis, Energy and Sensing

In recent years, bimetallic nanocrystals have attracted great interest from many researchers. Bimetallic nanocrystals are expected to exhibit improved physical and chemical properties due to the synergistic effect between the two metals, not just a combination of two monometallic properties. More importantly, the properties of bimetallic nanocrystals are significantly affected by their morphology, structure, and atomic arrangement. Reasonable regulation of these parameters of nanocrystals can effectively control their properties and enhance their practicality in a given application. This review summarizes some recent research progress in the controlled synthesis of shape, composition and structure, as well as some important applications of bimetallic nanocrystals. We first give a brief introduction to the development of bimetals, followed by the architectural diversity of bimetallic nanocrystals. The most commonly used and typical synthesis methods are also summarized, and the possible morphologies under different conditions are also discussed. Finally, we discuss the composition-dependent and shape-dependent properties of bimetals in terms of highlighting applications such as catalysis, energy conversion, gas sensing and bio-detection applications.

Temperature-Controlled Structural Variations of Meticulous Fibrous Networks of NiFe-Polymeric Zeolite Imidazolate Frameworks for Enhanced Performance in Electrocatalytic Water-Splitting Reactions

Developing non-noble, earth-ample, and stable electrocatalysts are highly anticipated in oxygen-evolution reaction (OER) and hydrogen-evolution reaction (HER) at unique pH conditions. Herein, we have synthesized bimetallic (nickel and iron) zeolite imidazolate framework (ZIF)-based nanofibrous materials via a simple electrospinning (ES) process. The structural stability of the fibrous material is subjected to various calcination conditions. We have elaborated the structural importance of the one-dimensional (1D) fibrous materials in electrocatalytic water-splitting reactions. As a result, NiFe-ZIF-NFs (Nanofibers)-RT (Room Temperature) have delivered a small overpotential of 241 mV at 10 mA cm^-2 current density in OER and 290 mV at a fixed current density of 50 mA cm^-2 in HER at two different pH conditions with 1 M KOH and 0.5 M H₂SO₄, respectively. Furthermore, it exposes the actual surface area of 27.270 m² g^-1 and a high electrochemical active surface area (ECSA) of 50 μF in OER and 55 μF in HER, which is responsible for the electrochemical performance with better stability. This exceptional activity of the materials is mainly attributed to the structural dependency of the fibrous network through the polymeric architecture.

Strong electrostatic adsorption-engaged fabrication of sub-3.0 nm PtRu alloy nanoparticles as synergistic electrocatalysts toward hydrogen evolution

Alloying of Pt with Ru to form ultrafine and well-defined PtRu alloy nanoparticles (NPs) for synergistically electrocatalytic hydrogen evolution is highly desirable but remains a synthetic challenge. Here, we report a strong electrostatic adsorption (SEA)-assisted fabrication of ultrafine and homogeneously distributed PtRu alloy NPs using ethylenediaminetetraacetic acid tetrasodium-derived carbon (EC) as a matrix. The O, N-rich EC with a hierarchically macro/meso/microporous structure and the SEA-assisted formation of the [Ru(bpy)₃][PtCl₆] complex ensure the successful generation of ultrasmall PtRu alloy NPs (2.93 nm in diameter) with high dispersion. The optimal PtRu/EC-700 delivers excellent electrocatalytic properties with an ultralow overpotential (η₁₀ = 18 mV), robust durability and good long-term stability for the alkaline hydrogen evolution reaction (HER). The ultrasmall PtRu alloy NPs with rich surface sites, the synergistic catalysis effect between Pt and Ru and the hierarchically macro/meso/microporous structure of O, N-rich EC cooperatively enhance the HER performance of PtRu/EC-700. This study provides an easy but effective way to construct metal alloy NPs with an ultrafine size and high dispersity for catalytic applications.

Prussian Blue Analogs and Their Derived Nanomaterials for Electrochemical Energy Storage and Electrocatalysis

Prussian blue analogs (PBAs), the oldest artificial cyanide-based coordination polymers, possess open framework structures, large specific surface areas, uniform metal active sites, and tunable composition, showing significant perspective in electrochemical energy storage. These electrochemically active materials have also been converted to various functional metal containing nanomaterials, including carbon encapsulated metals/metal alloys, metal oxides, metal sulfides, metal phosphides, etc. originating from the multi-element compositions as well as elaborate structure design. In this paper, a comprehensive review will be presented on the recent progresses in the development of PBA frameworks and their derivatives based electrode materials and electrocatalysts for electrochemical energy storage and conversion. In particular, it will focus on the synthesis of representative nanostructures, the structure design, and figure out the correlation between nanomaterials structure and electrochemical performance. Lastly, critical scientific challenges in this research area are also discussed and perspective directions for the future research in this field are provided, in order to provide a brand new vision into the further development of novel active materials for the next-generation advanced electrochemical devices.

CoMo-bimetallic N-doped porous carbon materials embedded with highly dispersed Pt nanoparticles as pH-universal hydrogen evolution reaction electrocatalysts

The hydrogen evolution reaction is a key half reaction for water electrolysis and is of great significance. Pt-based nanomaterials are promising candidates for HER electrocatalysts. However, the high price of platinum and poor durability impede their practical applications. Herein, a new CoMo-bimetallic hybrid zeolite imidazolate framework is employed to load Pt nanoparticles in a highly dispersed manner as a precursor to synthesize an efficient pH-universal HER electrocatalyst (PtCoMo@NC), which displays overpotentials of 26, 51, and 66 mV at a current density of 10 mA cm^-2 in acidic, basic, and neutral media, respectively. The strong synergistic effect of highly dispersed multi-type catalytic species, including cobalt, molybdenum carbide, and platinum (4.7%) promotes the catalytic activity in the HER process. Meanwhile, the aggregation of Pt nanoparticles is greatly restrained by the carbon matrix so that a brilliant long-time durability of 12 hours and a negligible current decrease in the LSV curve after 10 000 CV cycles are achieved.

Ultrafast and surfactant-free synthesis of Sub-3 nm nanoalloys by shear-assisted liquid-metal reduction

The uniform and surfactant-free synthesis of ultrafine alloy nanoparticles (NPs) still remains an ongoing challenge. Here, we developed a general route for synthesizing sub-3 nm nanoalloys on a carbon support via a shear-assisted liquid-metal reduction (SA-LMR) strategy. The utilization of shearing treatment resulted in the rapid release of electrons from the liquid sodium-potassium (NaK) alloy, which enabled the ultrafast reduction of precursor metal ions to metallic nanoalloys at room temperature. As a model system, Pt-Cu NPs with uniform distribution were synthesized and characterized by spectroscopic and microscopic techniques. The size, composition and structure of the Pt-Cu NPs could be tuned by controlling the volume of liquid NaK alloy and the reaction time. To prove the universality and utility of our method, the binary Pt-M (Fe, Co, Ni, and Cu) and ternary Pt-Cu-Fe nanoalloys deposited on a carbon support were prepared as hydrogen evolution reaction (HER) catalysts. This facile, rapid and universal synthesis technique has the potential to be employed in the large-scale production of nanomaterials and suggests a new direction for nanoalloys.

Improving plasma sprayed Raney-type nickel-molybdenum electrodes towards high-performance hydrogen evolution in alkaline medium

Rationally designed free-standing and binder-free Raney-type nickel-molybdenum (Ni-Mo) electrodes produced via atmospheric plasma spraying (APS) are developed by correlating APS process parameters with the microstructure of electrodes and their electrochemical performance in alkaline media. The results revealed that the electrode morphology and elemental composition are highly affected by the plasma parameters during the electrode fabrication. It is found that increasing plasma gas flow rate and input plasma power resulted in higher in-flight particle velocities and shorter dwell time, which in result delivered electrodes with much finer structure exhibiting homogeneous distribution of phases, larger quantity of micro pores and suitable content of Ni and Mo. Tafel slope of electrodes decreased with increasing the in-flight particles velocities from 71 to 33 mV dec^-1 in 30 wt.% KOH. However, beyond a critical threshold in-flight velocity and temperature of particles, electrodes started to exhibit larger globular pores and consequently reduced catalytic performance and higher Tafel slop of 36 mV dec^-1 in 30 wt.% KOH. Despite slightly lower electrochemical performance, the electrodes produced with highest plasma gas flow and energy showed most inter-particle bonded structure as well as highest stability with no measurable degradation over 47 days in operation as HER electrode in 30 wt.% KOH. The Raney-type Ni-Mo electrode fabricated at highest plasma gas flow rate and input plasma power has been tested as HER electrode in alkaline water electrolyzer, which delivered high current densities of 0.72 and 2 A cm^-2 at 1.8 and 2.2 V, respectively, representing a novel prime example of HER electrode, which can synergistically catalyze the HER in alkaline electrolyzer. This study shows that sluggish alkaline HER can be circumvented by rational electrode composition and interface engineering.

Basal-Plane Catalytic Activity of Layered Metallic Transition Metal Ditellurides for the Hydrogen Evolution Reaction

We report the electrochemical hydrogen evolution reaction (HER) of two-dimensional metallic transition metal dichalcogenides (TMDs). TMTe2 (TM: Mo, W, and V) single crystals were synthesized and characterized by optical microscopy, X-ray diffraction, and electrochemical measurements. We found that TMTe2 acts as a HER-active catalyst due to the inherent catalytic activity of its basal planes. Among the three metallic TMTe2, VTe2 shows the best HER performance with an overpotential of 441 mV and a Tafel slope of 70 mV/dec. It is 668 mV and 137 mV/dec for MoTe2 and 692 mV and 169 mV/dec for WTe2. Even though VTe2 has the lowest values in the exchange current density, the active site density, and turn-over-frequency (TOF) among the three TMTe2, the lowest charge transfer resistance (RCT) of VTe2 seems to be critical to achieving the best HER performance. First-principles calculations revealed that the basal-plane-active HER performance of metallic TMDs can be further enhanced with some Te vacancies. Our study paves the way to further study of the inherent catalytic activity of metallic 2D materials for active hydrogen production.

IrCo alloy nanoparticles supported on N-doped carbon for hydrogen evolution electrocatalysis in acidic and alkaline electrolytes

Designing efficient and low-cost electrocatalysts for the hydrogen evolution reaction (HER) is of great importance to advance water splitting technology towards practical applications. Herein, we report the preparation of IrCo nanoparticles supported on nitrogen-doped carbon (IrCo/NC) as a HER electrocatalyst in acidic and alkaline electrolytes. The IrCo/NC composite is obtained by pyrolyzing an Ir-doped Co(OH)2 precursor on g-C3N4, and is endowed with N-doped carbon and uniform IrCo alloy nanoparticles via a crystal confinement resulting from the Ir-doping into the Co(OH)2 layer. Electrocatalytic analysis shows that the IrCo/NC electrode requires low overpotentials of 32 mV at 10 mA cm-2 in 0.5 M H2SO4 and 33 mV in 1 M KOH, which are superior to those of the Co/NC and IrCo alloys that are free of Ir-doping or N-doped carbon. The results provide a strategy for designing and preparing active noble-transition bimetallic alloy electrocatalysts as efficient HER catalysts.

Colloidal bimetallic platinum–ruthenium nanoparticles in ordered mesoporous carbon films as highly active electrocatalysts for the hydrogen evolution reaction

Ordered mesoporous carbon films with high surface area, good electrical conductivity and an improved distribution of NPs with tunable composition show high electrocatalytic activity in HER.

Metallic nanostructures with low dimensionality for electrochemical water splitting

Metallic nanostructures with low dimensionality (one-dimension and two-dimension) possess unique structural characteristics and distinctive electronic and physicochemical properties including high aspect ratio, high specific surface area, high density of surface unsaturated atoms and high electron mobility. These distinctive features have rendered them remarkable advantages over their bulk counterparts for surface-related applications, for example, electrochemical water splitting. In this review article, we highlight the recent research progress in low-dimensional metallic nanostructures for electrochemical water splitting including hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Fundamental understanding of the electrochemistry of water splitting including HER and OER is firstly provided from the aspects of catalytic mechanisms, activity descriptors and property evaluation metrics. Generally, it is challenging to obtain low-dimensional metallic nanostructures with desirable characteristics for HER and OER. We hereby introduce several typical methods for synthesizing one-dimensional and two-dimensional metallic nanostructures including organic ligand-assisted synthesis, hydrothermal/solvothermal synthesis, carbon monoxide confined growth, topotactic reduction, and templated growth. We then put emphasis on the strategies adopted for the design and fabrication of high-performance low-dimensional metallic nanostructures for electrochemical water splitting such as alloying, structure design, surface engineering, interface engineering and strain engineering. The underlying structure-property correlation for each strategy is elucidated aiming to facilitate the design of more advanced electrocatalysts for water splitting. The challenges and perspectives for the development of electrochemical water splitting and low-dimensional metallic nanostructures are also proposed.

Boosted Electron-Transfer Kinetics of Hydrogen Evolution Reaction at Bimetallic RhCo Alloy Nanotubes in Acidic Solution

RhCo alloy nanotubes were synthesized via the reduction of single-phase Co₂RhO₄ nanotubes. The reduction was conducted by thermal annealing of the Co₂RhO₄ nanotubes under hydrogen gas flow. The crystallinity of the prepared RhCo alloy nanotubes depended on the reduction temperature: amorphous phase (200 °C reduction) and the crystalline phase (300 °C reduction). The hydrogen evolution reaction (HER) on RhCo alloys was investigated with voltammetry in 1.0 M HClO₄ solution. Amorphous RhCo alloys provided lower overpotential than the crystalline counterpart despite their similar morphology and composition. Of great interest, amorphous RhCo alloy nanotubes exhibited an outstanding HER electroactivity verified with a low overpotential at -10 mA cm^-2 (-22 mV) and a small Tafel slope (-24.1 mV dec^-1), outperforming commercial Pt, pure Rh metal, and the other previously reported Rh-based catalysts. This excellent HER activity of amorphous RhCo nanotubes was attributed to the amorphous structure having a large electrochemical surface area and maximized Rh-Co interfaces in the alloy facilitating HER. Active but expensive Rh alloyed with less active but cheap Co was successfully demonstrated as a potential cost-effective HER catalyst.

Atomically Dispersed Pt on Screw-like Pd/Au Core-shell Nanowires for Enhanced Electrocatalysis

Engineering noble metal nanostructures at the atomic level can significantly optimize their electrocatalytic performance and remarkably reduce their usage. We report the synthesis of atomically dispersed Pt on screw-like Pd/Au nanowires by using ultrafine Pd nanowires as seeds. Au can selectively grow on the surface of Pd nanowires by an island growth pattern to fabricate surface defect sites to load atomically dispersed Pt, which can be confirmed by X-ray absorption fine structure measurements and aberration corrected HRTEM images. The nanowires with 2.74 at % Pt exhibit superior HER properties in acidic solution with an overpotential of 20.6 mV at 10 mA cm^-2 and enhanced alkaline ORR performance with a mass activity over 15 times greater than the commercial platinum/carbon (Pt/C) catalysts.

Uniformly Decorated Molybdenum Carbide/Nitride Nanostructures on Biomass Templates for Hydrogen Evolution Reaction Applications

Natural fibrils derived from biomass were used as a template to synthesize uniformly decorated nanoparticles (10-12 nm) of molybdenum carbide (Mo₂C) and molybdenum nitride (Mo₂N) supported on carbon. The nanoparticles have been synthesized through the carburization and nitridation of molybdenum on cotton fibrils, using a high-temperature solid-state reaction. The catalyst exhibits an onset potential of 110 mV and an overpotential of 167 mV to derive a cathodic current density of 10 mA cm^-2. The electrocatalyst also demonstrates excellent long-term durability of more than 2500 cycles in acidic media with a Tafel slope value of 62 mV dec^-1.

Highly Electroactive Ni Pyrophosphate/Pt Catalyst toward Hydrogen Evolution Reaction

Robust electrocatalysts toward the resourceful and sustainable generation of hydrogen by splitting of water via electrocatalytic hydrogen evolution reaction (HER) are a prerequisite to realize high-efficiency energy research. Highly electroactive catalysts for hydrogen production with ultralow loading of platinum (Pt) have been under exhaustive exploration to make them cutting-edge and cost-effectively reasonable for water splitting. Herein, we report the synthesis of hierarchically structured nickel pyrophosphate (β-Ni₂P₂O₇) by a precipitation method and nickel phosphate (Ni₃(PO₄)₂) by two different synthetic routes, namely, simple cost-effective precipitation and solution combustion processes. Thereafter, Pt-decorated nickel pyrophosphate and nickel phosphate (β-Ni₂P₂O₇/Pt and Ni₃(PO₄)₂/Pt) were prepared by using potassium hexachloroplatinate and ascorbic acid. The fabricated novel nickel pyrophosphate and nickel phosphate/Pt materials were utilized as potential and affordable electrocatalysts for HER by water splitting. The detailed electrochemical studies revealed that the β-Ni₂P₂O₇/Pt (1 μg·cm^-2 Pt) electrocatalyst showed excellent electrocatalytic performances for HER in acidic solution with an overpotential of 28 mV at -10 mA·cm^-2, a Tafel slope of 32 mV·dec, and an exchange current density ( j₀) of -1.31 mA·cm^-2, which were close to the values obtained using the Vulcan/Pt (8.0 μg·cm^-2 Pt), commercial benchmarking electrocatalyst with eight times higher Pt amount. Furthermore, the β-Ni₂P₂O₇/Pt electrocatalyst maintains an excellent stability for over -0.1 V versus RHE for 12 days, keeping j₀ equal after the stability test (-1.28 mA cm^-2). Very well-distributed Pt NPs inside the "cages" on the β-Ni₂P₂O₇ structure with a crystalline pattern of 0.67 nm distance to the Ni₂P₂O₇/Pt electrocatalyst, helping the Volmer-Tafel mechanism with the Tafel reaction as a major rate-limiting step, help to liberate very fast the Pt sites after HER. The high electrocatalytic performance and remarkable durability showed the β-Ni₂P₂O₇/Pt material to be a promising cost-effective electrocatalyst for hydrogen production.

Tungsten-inert gas welding electrodes as low-cost, green and pH-universal electrocatalysts for the hydrogen evolution reaction

Lanthanated tungsten electrodes were shown to be green, durable, low-cost, pH-universal and efficient electrocatalysts for the hydrogen evolution reaction.

Ultrasmall Ru/Cu-doped RuO2 Complex Embedded in Amorphous Carbon Skeleton as Highly Active Bifunctional Electrocatalysts for Overall Water Splitting

Developing highly active electrocatalysts with superior durability for both the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in the same electrolyte is a grand challenge to realize the practical application of electrolysis water for producing hydrogen. In this work, an ultrasmall Ru/Cu-doped RuO₂ complex embedded in an amorphous carbon skeleton is synthesized, through thermolysis of Ru-modified Cu-1,3,5-benzenetricarboxylic acid (BTC), as a highly efficient bifunctional catalyst for overall water splitting electrocatalysis. The ultrasmall Ru nanoparticles in the complex expose more activity sites for hydrogen evolution and outperform the commercial Pt/C. Meanwhile, the ultrasmall RuO₂ nanoparticles exhibit superior oxygen evolution performance over commercial RuO₂, and the doping of Cu into the ultrasmall RuO₂ nanoparticles further enhances the oxygen evolution performance of the catalyst. The outstanding OER and decent HER catalytic activity endow the complex with impressive overall water splitting performance superior to that of the state-of-the-art electrocatalysts, which just require 1.47 and 1.67 V to achieve a current density of 10 mA cm^-2 and 100 mA cm^-2. The density functional theory calculations reveal that a Cu dopant could effectively tailor the d-band center, thereby tuning electronic structure of Ru activity sites on the RuO₂ (110) plane and ultimately improving the OER performance of RuO₂.

Carbon-Quantum-Dots-Loaded Ruthenium Nanoparticles as an Efficient Electrocatalyst for Hydrogen Production in Alkaline Media

Highly active, stable, and cheap Pt-free catalysts for the hydrogen evolution reaction (HER) are facing increasing demand as a result of their potential use in future energy-conversion systems. However, the development of HER electrocatalysts with Pt-like or even superior activity, in particular ones that can function under alkaline conditions, remains a significant challenge. Here, the synthesis of a novel carbon-loaded ruthenium nanoparticle electrocatalyst (Ru@CQDs) for the HER, using carbon quantum dots (CQDs), is reported. Electrochemical tests reveal that, even under extremely alkaline conditions (1 m KOH), the as-formed Ru@CQDs exhibits excellent catalytic behavior with an onset overpotential of 0 mV, a Tafel slope of 47 mV decade^-1 , and good durability. Most importantly, it only requires an overpotential of 10 mV to achieve the current density of 10 mA cm^-2 . Such catalytic characteristics are superior to the current commercial Pt/C and most noble metals, non-noble metals, and nonmetallic catalysts under basic conditions. These findings open a new field for the application of CQDs and add to the growing family of metal@CQDs with high HER performance.

Two-Step Synthesis of Cobalt Iron Alloy Nanoparticles Embedded in Nitrogen-Doped Carbon Nanosheets/Carbon Nanotubes for the Oxygen Evolution Reaction

There is a vital need to explore highly efficient and stable non-precious-metal catalysts for the oxygen evolution reaction (OER) to reduce the overpotential and further improve the energy-conversion efficiency. Herein, we report a unique and cost-effective lyophilization and thermal treatment two-step procedure to synthesize a high-performance hybrid consisting of CoFe alloy nanoparticles embedded in N-doped carbon nanosheets interspersed with carbon nanotubes (CoFe-N-CN/CNTs) hybrid. The lyophilization step during the catalyst preparation leads to a uniform dispersion of carbon-like precursors and avoids the agglomeration of metal particles. In addition, the inserted CNTs and doped N in this hybrid provide a good electrical conductivity, an abundance of chemically active sites, good mass transport capability, and effective gas adsorption/release channels. All these lead to a high specific surface area of 240.67 m²  g^-1 , favorable stability, and remarkable OER activities with an overpotential of only 285 mV at a current density of 10 mA cm^-2 and a Tafel slope of 51.09 mV dec^-1 in 1.0 m KOH electrolyte, which is even superior to commercial IrO₂ catalysts. The CoFe-N-CN/CNTs hybrid thus exhibits great potential as a highly efficient and earth-abundant anode OER electrocatalyst.

Tuning the Activity of Carbon for Electrocatalytic Hydrogen Evolution via an Iridium-Cobalt Alloy Core Encapsulated in Nitrogen-Doped Carbon Cages

Graphene, a 2D material consisting of a single layer of sp² -hybridized carbon, exhibits inert activity as an electrocatalyst, while the incorporation of heteroatoms (such as N) into the framework can tune its electronic properties. Because of the different electronegativity between N and C atoms, electrons will transfer from C to N in N-doped graphene nanosheets, changing inert C atoms adjacent to the N-dopants into active sites. Notwithstanding the achieved progress, its intrinsic activity in acidic media is still far from Pt/C. Here, a facile annealing strategy is adopted for Ir-doped metal-organic frameworks to synthesize IrCo nanoalloys encapsulated in N-doped graphene layers. The highly active electrocatalyst, with remarkably reduced Ir loading (1.56 wt%), achieves an ultralow Tafel slope of 23 mV dec^-1 and an overpotential of only 24 mV at a current density of 10 mA cm^-2 in 0.5 m sulfuric acid solution. Such superior performance is even superior to the noble-metal catalyst Pt. Surface structural and computational studies reveal that the superior behavior originates from the decreased ΔG_H* for HER induced by the electrons transferred from the alloy core to the graphene layers, which is beneficial for enhancing CH binding.

Polyoxometalate-based metal–organic framework loaded with an ultra-low amount of Pt as an efficient electrocatalyst for hydrogen production

A low-Pt content polyoxometalate-based metal–organic framework (Pt@POMOF-1/KB) displays a highly efficient performance towards the hydrogen evolution reaction.