Inorganic Surface Coating with Fast Wetting-Dewetting Transitions for Liquid Manipulations

Active Control of Contact Angles of Various Liquids from the Response of Self-Assembled Thiol Molecules to Electric Current

The ability to change wettability in situ would realize active surfaces that can change their functionality and adapt to different environments. This article reports a new and easy method that controls surface wettability in situ. In doing so, three hypotheses were to be proven. First, thiol molecules with dipole moments at the end that were adsorbed onto gold could change the contact angles of nonpolar or slightly polar liquids when an electric current was provided at the gold surface without having to ionize the dipole. It was also hypothesized that the molecules would undergo conformation changes as their dipoles would align with the magnetic field induced by the applied current. Second, the ability to change contact angles was modified by mixing ethanethiol, a much shorter thiol with no dipole, with the abovementioned thiol molecules because it would provide space for the thiol molecules to undergo conformation changes. Third, the indirect evidence of the conformation change was verified with attenuated total reflection Fourier transform infrared (FT-IR) spectroscopy. Four thiol molecules that controlled the contact angles of deionized water and hydrocarbon liquids were identified. The abilities of those four molecules in changing the contact angles were modified by adding ethanethiol. A quartz crystal microbalance was used to infer the possible change in the distance between the adsorbed thiol molecules by investigating adsorption kinetics. The changes in FT-IR peaks with respect to applied currents were also presented as indirect evidence for the conformation change. This method was compared with other reported methods that control wettability in situ. The differences between the voltage-driven method to induce conformation changes of thiol molecules and the method presented in this paper were further discussed to emphasize that the mechanism by which the conformation change was induced in this article was most likely because of the dipole-electric current interaction.

Smart surfaces with reversibly switchable wettability: Concepts, synthesis and applications

As a growing hot research topic, manufacturing smart switchable surfaces has attracted much attention in the past a few years. The state-of-the-art study on reversibly switchable wettability of smart surfaces has been presented in this systematic review. External stimuli are brought about to render the alteration in chemical conformation and surface morphology to drive the wettability switch. Here, starting from the fundamental theories related to the surfaces wetting principles, highlights on different triggers for switchable wettability, such as pH, light, ions, temperature, electric field, gas, mechanical force, and multi-stimuli are discussed. Different applications that have various wettability requirement are targeted, including oil-water separation, droplets manipulation, patterning, liquid transport, and so on. This review aims to provide a deep insight into responsive interfacial science and offer guidance for smart surface engineering. It ends with a summary of current challenges, future opportunities, and potential solutions on smart switch of wettability on superwetting surfaces.

The Influence of ZnO Oxide Layer on the Physicochemical Behavior of Ti6Al4V Titanium Alloy

Titanium and its alloys are characterized by high biocompatibility and good corrosion resistance as a result of the ability to form a TiO₂ oxide layer. However, based on literature data it can be concluded that titanium degradation products, in the form of titanium particles, metal-protein groups, oxides and ions, may cause allergic, inflammatory reactions and bone resorption. The corrosion process of Ti6Al4V in the human body environment may be intensified by a decreased pH and concentration of chloride compounds. The purpose of this article was to analyze the corrosion resistance of the Ti6Al4V alloy, obtained by the selective laser melting method in a corrosion solution of neutral pH and in a solution simulating peri-implant inflammatory conditions. Additionally, the influence of zinc oxide deposited by the atomic layer deposition method on the improvement of the physicochemical behavior of the Ti6Al4V alloy was analyzed. In order to characterize the ZnO layer, tests of chemical and phase composition as well as surface morphology investigation were performed. As part of the assessment of the physicochemical properties of the uncoated samples and those with the ZnO layer, tests of wetting angle, pitting corrosion and impedance corrosion were carried out. The number of ions released after the potentiodynamic test were measured using the inductively coupled plasma atomic emission spectrometry (ICP-AES) method. It can be concluded that samples after surface modification (with the ZnO layer) were characterized by favorable physicochemical properties and had higher corrosion resistance.

Thickness-dependent fast wetting transitions due to the atomic layer deposition of zinc oxide on a micro-pillared surface

Smart surfaces promote the fundamental understanding of wetting and are widely used in practical applications for energy and water collection. Light-induced switchable wettability facilitated by ZnO coatings, for instance, was developed for liquid manipulation at the surface. However, the transition of wetting states was reported to follow a hydrophobic–hydrophilic cycle in an hour, which is very long and may limit its future applications. We recently discovered that the cycle of the wetting state transitions on inorganic coatings can be shortened to less than 100 seconds by using ALD-coated ZnO on a pillared surface. However, the mechanisms are still unclear. Here, we investigated the effects of coating thickness on the transition speed and found that it significantly depended on the thickness of the coating with the optimal thickness less than 50 nm. We found that the minimum critical time for a wetting state transition cycle was less than 50 seconds with a thickness of 40 nm. Although the transition time of surfaces with coatings over 70 nm thickness remained constant at 10 min for a cycle, it was shorter than those of other deposition techniques for a coarse surface. Here, we propose a “penetration–diffusion” model to explain the fast and thickness-dependent wetting transitions. Our study may provide a new paradigm for fast wetting transition surfaces with cycle time within tens of seconds using a homogeneous thin layer coated on a rough surface.

Smart surfaces promote the fundamental understanding of wetting and are widely used in practical applications for energy and water collection.

Tunable Spreading and Shrinking on Photocontrolled Liquid Substrate

Droplets of n-hexadecane were observed to shrink under ultraviolet (365 nm) and spread under blue light (475 nm) irradiation on an aqueous solution of photosensitive surfactant AzoTAB. We demonstrate that the change of wettability of n-hexadecane droplet on the solution depends on the change of oil-water interface tension. According to the addition of ethanol into the substrate, the change of relative diameter ΔD/D exceeds 20%, much larger than the system without ethanol. With light-emitting diode (LED) light as a sole power source, without any other triggers, we provide a contactless and isothermal method to realize photocontrolled alternative spreading and shrinking of a droplet on a liquid surface, which provides a basis for a chromocapillary-based optical zoom liquid lens.

Smart Copolymer-Functionalized Flexible Surfaces with Photoswitchable Wettability: From Superhydrophobicity with "Rose Petal" Effect to Superhydrophilicity

Realizing smart surfaces with switchable wettability inspired by nature continues to be fascinating as well as challenging. Herein, we present a versatile dip-coating approach to fabricate smart polymer-functionalized flexible surfaces with photoswitchable superwettability. Decorated with novel acrylate copolymers bearing a trifluoromethyl side chain and fluorine-containing azobenzene derivative moieties, the modified cotton fabric possesses a rose petal-like superhydrophobicity with contact angles larger than 150° and high water adhesion. This smart surface exhibits rapid phototriggered wettability transformation between superhydrophobicity and superhydrophilicity via alternate irradiation with ultraviolet and visible light, respectively. Meanwhile, the as-prepared flexible smart surfaces have excellent chemical and physical stabilities, which could tolerate harsh environmental conditions and repetitive mechanical deformation (e.g., stretching, curling, folding, and twisting) as well as multiple washing. More importantly, based on the excellent photocontrollability, various erasable and rewritable patterns with distinct wetting properties upon selective photoirradiation can be obtained. This simple strategy and the developed smart surface may find more advanced potential applications in controllable liquid transport, patterning droplet microarrays, and microfluidic devices.

Bioinspired Designs of Superhydrophobic and Superhydrophilic Materials

Bioinspired designs of superhydrophobic and superhydrophilic materials have been an important and fascinating area of research in recent years for their extensive potential application prospects from industry to our daily life. Despite extensive progress, existing research achievements are far from real applications. From biomimetic performance to service life, the related research has faced serious problems at present. A timely outlook is therefore necessary to summarize the existing research, to discuss the challenges faced, and to propose constructive advice for the ongoing scientific trend. Here, we comb the process of development of bioinspired superhydrophobic and superhydrophilic materials at first. Then, we also describe how to design artificial superhydrophobic and superhydrophilic materials. Furthermore, current challenges faced by bioinspired designs of superhydrophobic and superhydrophilic materials are pointed out, separately, and the possible solutions are discussed. Emerging applications in this field are also briefly considered. Finally, the development trend within this field is highlighted to lead future research.

Light-Activated Hybrid Nanocomposite Film for Water and Oxygen Sensing

Oxygen and water vapor sensing properties are investigated in metal-oxide-hybrid polymer nanocomposite thin films generated by infiltration synthesis, which incorporates molecular ZnO into the matrix of SU-8 polymer, a common negative-tone photoresist. The hybrid thin films display 20-fold higher gravimetric responses to oxygen and water vapor than those of control ZnO thin films in the dark. An additional 50-500% enhanced responses are detected under UV irradiation. The overall enhanced gravimetric response in the hybrid film is attributed to the ZnO molecules distributed in the polymer matrix, whereas the UV enhancement is explained by the light-induced, reversible generation of hydrophilic fluoroantimonic acid from triarylsulfonium hexafluoroantimonate photoacids, which leads to the increased surface potential and adsorption energies for oxygen and water. A gravimetric sensor based on a series of ZnO-infiltrated SU-8 films under UV excitation enables 96% accurate classification of water and oxygen environment with sub 10 mTorr detection limits. The results demonstrate UV-induced fully reversible surface hydrophilicity of ZnO/SU-8 hybrid nanocomposites.