Measurement of Cohesion and Adhesion of Semiconducting Polymers by Scratch Testing: Effect of Side-Chain Length and Degree of Polymerization

Material Design and Device Fabrication Strategies for Stretchable Organic Solar Cells

Recent advances in the power conversion efficiency (PCE) of organic solar cells (OSCs) have greatly enhanced their commercial viability. Considering the technical standards (e.g., mechanical robustness) required for wearable electronics, which are promising application platforms for OSCs, the development of fully stretchable OSCs (f-SOSCs) should be accelerated. Here, a comprehensive overview of f-SOSCs, which are aimed to reliably operate under various forms of mechanical stress, including bending and multidirectional stretching, is provided. First, the mechanical requirements of f-SOSCs, in terms of tensile and cohesion/adhesion properties, are summarized along with the experimental methods to evaluate those properties. Second, essential studies to make each layer of f-SOSCs stretchable and efficient are discussed, emphasizing strategies to simultaneously enhance the photovoltaic and mechanical properties of the active layer, ranging from material design to fabrication control. Key improvements to the other components/layers (i.e., substrate, electrodes, and interlayers) are also covered. Lastly, considering that f-SOSC research is in its infancy, the current challenges and future prospects are explored.

Fabrication of PCDTBT Conductive Network via Phase Separation

Poly[N-9'-hepta-decanyl-2,7-carbazole-alt-5-5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT) is a stable semiconducting polymer with high rigidity in its molecular chains, which makes it difficult to organize into an ordered structure and affects the device performance. Here, a PCDTBT network consisting of aggregates and nanofibers in thin films was fabricated through the phase separation of mixed PCDTBT and polyethylene glycol (PEG). Using atomic force microscopy (AFM), the effect of the blending conditions (weight ratio, solution concentration, and molecular weight) and processing conditions (substrate temperature and solvent) on the resulting phase-separated morphologies of the blend films after a selective washing procedure was studied. It was found that the phase-separated structure's transition from an island to a continuous structure occurred when the weight ratio of PCDTBT/PEG changed from 2:8 to 7:3. Increasing the solution concentration from 0.1 to 3.0 wt% led to an increase in both the height of the PCDTBT aggregate and the width of the nanofiber. When the molecular weight of the PEG was increased, the film exhibited a larger PCDTBT aggregate size. Meanwhile, denser nanofibers were found in films prepared using PCDTBT with higher molecular weight. Furthermore, the electrical characteristics of the PCDTBT network were measured using conductive AFM. Our findings suggest that phase separation plays an important role in improving the molecular chain diffusion rate and fabricating the PCDTBT network.

Strain-Microstructure-Optoelectronic Inter-Relationship toward Engineering Mechano-Optoelectronic Conjugated Polymer Thin Films

Mechano-optoelectronic (MO) behavior indicates changes in optoelectronic properties in response to the applied mechanical deformation. The MO behavior can be employed to monitor the mechanical deformation of a targeted system by tracing its optoelectronic properties. Poly(3-hexylthiophene) and phenyl-C61-butyric acid methyl ester (P3HT/PCBM) blend thin films exhibited changes in direct current under tensile strain. Although optoelectronic properties and photovoltaic performance of P3HT/PCBM blends have been studied extensively and intensively, research required for MO properties has a fundamental difference from previous research mostly for solar cells. In research for MO systems, a greater extent of changes in optoelectronic properties under mechanical deformation is favorable. Herein, previous research for optoelectronic properties and mechanical properties of conjugated polymers will be reviewed from a perspective on MO properties. The microstructure of a conjugated polymer thin film plays a pivotal role in its optoelectronic properties and mechanical properties. Key parameters involved in the microstructure of conjugated polymer thin films will be addressed. A scalable process is required to broaden applications of MO systems. Potential challenges in the fabrication of MO conjugated polymer thin films will be discussed. Finally, this review is envisioned to provide insight into the design and manufacturing of MO conjugated polymer thin films.

Quantifying Solvent Effects on Polymer Surface Grafting

When grafting polymers onto surfaces, the reaction conditions critically influence the resulting interface properties, including the grafting density and molar mass distribution (MMD) on the surface. Herein, we show theoretically and experimentally that the application of poor solvents is beneficial for the "grafting-to" approach. We demonstrate the effect by grafting poly(methyl methacrylate) chains on silica nanoparticles in different solvents and compare the MMD of the polymer in solution before and after grafting via size exclusion chromatography (SEC). The shorter polymer chains are preferentially grafted onto the surface, leading to a distortion effect between the MMD in solution and on surfaces. The molecular weight distortion effect is significantly higher for ethyl acetate (good solvent quality, difference in M_w surface to solution 14%) than for N,N-dimethylacetamide (poor solvent quality, 6%). The difference in MMD on the surface to the solution significantly affects both the surface properties (e.g. the grafting densities) and their determination.