Surface-Modified Sulfur Nanorods Immobilized on Radially Assembled Open-Porous Graphene Microspheres for Lithium-Sulfur Batteries

2D Nano-Channeled Molybdenum Compounds for Accelerating Interfacial Polysulfides Catalysis in Li-S Battery

The shuttle effect, which causes the loss of active sulfur, passivation of lithium anode, and leads to severe capacity attenuation, is currently the main bottleneck for lithium-sulfur batteries. Recent studies have disclosed that molybdenum compounds possess exceptional advantages as a polar substrate to immobilize and catalyze lithium polysulfide such as high conductivity and strong sulfiphilicity. However, these materials show incomplete contact with sulfur/polysulfides, which causes uneven redox conversion of sulfur and results in poor rate performance. Herein, a new type of 2D nano-channeled molybdenum compounds (2D-MoNx) via the 2D organic-polyoxometalate superstructure for accelerating interfacial polysulfide catalysis toward high-performance lithium-sulfur batteries is reported. The 2D-MoNx shows well-interlinked nano-channels, which increase the reactive interface and contact surface with polysulfides. Therefore, the battery equipped with 2D-MoNx displays a high discharge capacity of 912.7 mAh g-1 at 1 C and the highest capacity retention of 523.7 mAh g-1 after 300 cycles. Even at the rate of 2 C, the capacity retention can be maintained at 526.6 mAh g-1 after 300 cycles. This innovative nano-channel and interfacial design of 2D-MoNx provides new nanostructures to optimize the sulfur redox chemistry and eliminate the shuttle effect of polysulfides.

Single-Atomic Dispersion of Fe and Co Supported on Reduced Graphene Oxide for High-Performance Lithium-Sulfur Batteries

High theoretical energy density and low cost make lithium-sulfur (LSB) batteries a promising system for next-generation energy storage. LSB performance largely depends on efficient reversible conversion of elemental sulfur to Li2S. Here, well-designed sulfur host materials including Fe or Co single atoms embedded on N-doped reduced graphene oxide (MNC/G with M = Fe or Co) are proposed to tackle the LSB challenges and enhance the electrochemical performance. Using a combination of Mössbauer spectroscopy and high-resolution scanning electron microscopy, the atomic dispersion of Co and Fe was revealed up to relatively high mass loadings. After optimization of the electrolyte/sulfur (E/S) ratio, FeNC/G shows the most promising cycle performance combining a constant high discharge capacity at low E/S values with the lowest polarization. In particular, the material FeNC/G@S with a high sulfur loading (9.4 mg cm-2) delivers a high area capacity of 7.7 mAh cm-2 under lean electrolyte conditions (6 mL g-1).

Confined Synthesis of Amorphous Al2 O3 Framework Nanocomposites Based on the Oxygen-Potential Diagram as Sulfur Hosts for Catalytic Conversion

Sulfur cathodes in Li-S batteries suffer significant volumetric expansion and lack of catalytic activity for polysulfide conversion. In this study, a confined self-reduction synthetic route is developed for preparing nanocomposites using diverse metal ions (Mn2+ , Co2+ , Ni2+ , and Zn2+ )-introduced Al-MIL-96 as precursors. The Ni2+ -introduced Al-MIL-96-derived nanocomposite contains a "hardness unit", amorphous aluminum oxide framework, to restrain the volumetric expansion, and a "softness unit", Ni nanocrystals, to improve the catalytic activity. The oxygen-potential diagram theoretically explains why Ni2+ is preferentially reduced. Postmortem microstructure characterization confirms the suppressive volume expansion. The in situ ultraviolet-visible measurements are performed to probe the catalytic activity of polysulfide conversion. This study provides a new perspective for designing nanocomposites with "hardness units" and "softness units" as sulfur or other catalyst hosts.

Conductive Polymer Coated Layered Double Hydroxide as a Novel Sulfur Reservoir for Flexible Lithium-Sulfur Batteries

Lithium-sulfur battery (LSB) is widely regarded as the most promising next-generation energy storage system owing to its high theoretical capacity and low cost. However, the practical application of LSBs is mainly hampered by the low electronic conductivity of the sulfur cathode and the notorious "shuttle effect", which lead to high voltage polarization, severe over-charge behavior, and rapid capacity decay. To address these issues, a novel sulfur reservoir is synthesized by coating polypyrrole (PPy) thin film on hollow layered double hydroxide (LDH) (PPy@LDH). After compositing with sulfur, such PPy@LDH-S cathode shows a multi-functional effect to reserve lithium polysulfides (LiPSs). In addition, the unique architecture provides sufficient inner space to encapsulate the volume expansion and enhances the reaction kinetics of sulfur-based redox chemistry. Theoretical calculations have illustrated that the PPy@LDH has shown stronger chemical adsorption capability for LiPSs than those of porous carbon and LDH, preventing the shuttling of LiPSs and enhancing the nucleation affinity of liquid-solid conversion. As a result, the PPy@LDH-S electrode delivers a stable cycling performance and a superior rate capability. Flexible battery has demonstrated this PPy@LDH-S electrode can work properly with treatments of bending, folding, and even twisting, paving the way for wearable devices and flexible electronics.

Shaping Sulfur Precursors to Low Dimensional (0D, 1D and 2D) Sulfur Nanomaterials: Synthesis, Characterization, Mechanism, Functionalization, and Applications

Low-dimensional sulfur nanomaterials featuring with 0D sulfur nanoparticles (SNPs), sulfur nanodots (SNDs) and sulfur quantum dots (SQDs), 1D sulfur nanorods (SNRs), and 2D sulfur nanosheets (SNSs) have emerged as an environmentally friendly, biocompatible class of metal-free nanomaterials, sparking extensive interest in a wide range application. In this review, various synthetic methods, precise characterization, creative formation mechanism, delicate functionalization, and versatile applications of low dimensional sulfur nanomaterials over the last decades are systematically summarized. Initially, it is striven to summarize the progress of low dimensional sulfur nanomaterials from versatile precursors by using different synthetic approaches and various characterization. Then, a multi-faceted proposed formation mechanism with emphasis on how these different precursors produce corresponding SNPs, SNDs, SQDs, SNRs, and SNSs is highlighted. Besides, it is essential to fine-tune the surface functional groups of low dimensional sulfur nanomaterials to form new complex nanomaterials. Finally, these sulfur nanomaterials are being investigated in bio-sensing, bio-imaging, lithium-sulfur batteries, antibacterial activities, plant growth along with future perspective and challenges in emerging fields. The purpose of this review is to tailor low dimensional nanomaterials through accurately selecting precursors or synthetic approach and provide a foundation for the formation of versatile sulfur nanostructure.

A Ti3C2Tx-Based Composite as Separator Coating for Stable Li-S Batteries

The nitrogen-doped MXene carbon nanosheet-nickel (N-M@CNi) powder was successfully prepared by a combined process of electrostatic attraction and annealing strategy, and then applied as the separator coating in lithium-sulfur batteries. The morphology and structure of the N-M@CNi were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), Raman spectrum, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption-desorption method. The strong LiPS adsorption ability and high conductivity are associated with the N-doped carbon nanosheet-Ni modified surface. The modified separator offers the cathode of Li-S cell with greater sulfur utilization, better high-rate adaptability, and more stable cycling performance compared with the pristine separator. At 0.2 C the cell with N-M@CNi separator delivers an initial capacity of 1309 mAh g^-1. More importantly, the N-M@CNi separator is able to handle a cathode with 3.18 mg cm^-2 sulfur loading, delivering a capacity decay rate of 0.043% with a high capacity retention of 95.8%. Therefore, this work may provide a feasible approach to separator modification materials towards improved Li-S cells with improved stability.

Approaches to Combat the Polysulfide Shuttle Phenomenon in Li–S Battery Technology

Lithium–sulfur battery (LSB) technology has tremendous prospects to substitute lithium-ion battery (LIB) technology due to its high energy density. However, the escaping of polysulfide intermediates (produced during the redox reaction process) from the cathode structure is the primary reason for rapid capacity fading. Suppressing the polysulfide shuttle (PSS) is a viable solution for this technology to move closer to commercialization and supersede the established LIB technology. In this review, we have analyzed the challenges faced by LSBs and outlined current methods and materials used to address these problems. We conclude that in order to further pioneer LSBs, it is necessary to address these essential features of the sulfur cathode: superior electrical conductivity to ensure faster redox reaction kinetics and high discharge capacity, high pore volume of the cathode host to maximize sulfur loading/utilization, and polar PSS-resistive materials to anchor and suppress the migration of polysulfides, which can be developed with the use of nanofabrication and combinations of the PSS-suppressive qualities of each component. With these factors addressed, our world will be able to forge ahead with the development of LSBs on a larger scale—for the efficiency of energy systems in technology advancement and potential benefits to outweigh the costs and performance decay.

Rational Design and General Synthesis of Multimetallic Metal-Organic Framework Nano-Octahedra for Enhanced Li-S Battery

Metal-organic frameworks (MOFs), which consist of central metal nodes and organic linkers, constitute a fast growing class of crystalline porous materials with excellent application potential. Herein, a series of Mn-based multimetallic MOF (bimetallic and trimetallic MIL-100) nano-octahedra are prepared by a facile one-pot synthetic strategy. The types and proportions of the incorporated elements can be tuned while retaining the original topological structure. The introduction of other metal ions is verified at the atomic level by combining X-ray absorption fine structure experiments and theoretical calculations. Furthermore, these multimetallic Mn-based MIL-100 nano-octahedra are utilized as sulfur hosts to prepare cathodes for Li-S batteries. The MnNi-MIL-100@S cathode exhibits the best Li-S battery performance among all reported MIL-100@S composite cathode materials, with a reversible capacity of ≈708.8 mAh g^-1 after 200 cycles. The synthetic strategy described herein is utilized to incorporate metal ions into the MOF architecture, of which the parent monometallic MOF nano-octahedra cannot be prepared directly, thus rationally generating novel multimetallic MOFs. Importantly, the strategy also allows for the general synthesis and study of various micro-/nanoscale MOFs in the energy storage field.

Multifunctional Metal Phosphides as Superior Host Materials for Advanced Lithium-Sulfur Batteries

For the past few years, a new generation of energy storage systems with large theoretical specific capacity has been urgently needed because of the rapid development of society. Lithium-sulfur (Li-S) batteries are regarded as one of the most promising candidates for novel battery systems, since their resurgence at the end of the 20th century Li-S batteries have attracted ever more attention, attributed to their notably high theoretical energy density of 2600 W h kg^-1 , which is almost five times larger than that of commercial lithium-ion batteries (LIBs). One of the determining factors in Li-S batteries is how to design/prepare the sulfur cathode. For the sulfur host, the major technical challenge is avoiding the shuttling effect that is caused by soluble polysulfides during the reaction. In past decades, though the sulfur cathode has developed greatly, there are still some enormous challenges to be conquered, such as low utilization of S, rapid decay of capacity, and poor cycle life. This article spotlights the recent progress and foremost findings in improving the performance of Li-S batteries by employing multifunctional metal phosphides as host materials. The current state of development of the sulfur electrode of Li-S batteries is summarized by emphasizing the relationship between the essential properties of metal phosphide-based hybrid nanomaterials, the chemical reaction with lithium polysulfides and the latter's influence on electrochemical performance. Finally, trends in the development and practical application of Li-S batteries are also pointed out.

Emerging trends in anion storage materials for the capacitive and hybrid energy storage and beyond

Electrochemical capacitors charge and discharge more rapidly than batteries over longer cycles, but their practical applications remain limited due to their significantly lower energy densities. Pseudocapacitors and hybrid capacitors have been developed to extend Ragone plots to higher energy density values, but they are also limited by the insufficient breadth of options for electrode materials, which require materials that store alkali metal cations such as Li⁺ and Na⁺. Herein, we report a comprehensive and systematic review of emerging anion storage materials for performance- and functionality-oriented applications in electrochemical and battery-capacitor hybrid devices. The operating principles and types of dual-ion and whole-anion storage in electrochemical and hybrid capacitors are addressed along with the classification, thermodynamic and kinetic aspects, and associated interfaces of anion storage materials in various aqueous and non-aqueous electrolytes. The charge storage mechanism, structure-property correlation, and electrochemical features of anion storage materials are comprehensively discussed. The recent progress in emerging anion storage materials is also discussed, focusing on high-performance applications, such as dual-ion- and whole-anion-storing electrochemical capacitors in a symmetric or hybrid manner, and functional applications including micro- and flexible capacitors, desalination, and salinity cells. Finally, we present our perspective on the current impediments and future directions in this field.

Graphene-Based Nanomaterials as the Cathode for Lithium-Sulfur Batteries

The global energy crisis and environmental problems are becoming increasingly serious. It is now urgent to vigorously develop an efficient energy storage system. Lithium-sulfur batteries (LSBs) are considered to be one of the most promising candidates for next-generation energy storage systems due to their high energy density. Sulfur is abundant on Earth, low-cost, and environmentally friendly, which is consistent with the characteristics of new clean energy. Although LSBs possess numerous advantages, they still suffer from numerous problems such as the dissolution and diffusion of sulfur intermediate products during the discharge process, the expansion of the electrode volume, and so on, which severely limit their further development. Graphene is a two-dimensional crystal material with a single atomic layer thickness and honeycomb bonding structure formed by sp2 hybridization of carbon atoms. Since its discovery in 2004, graphene has attracted worldwide attention due to its excellent physical and chemical properties. Herein, this review summarizes the latest developments in graphene frameworks, heteroatom-modified graphene, and graphene composite frameworks in sulfur cathodes. Moreover, the challenges and future development of graphene-based sulfur cathodes are also discussed.

Layered Double Hydroxide Quantum Dots for Use in a Bifunctional Separator of Lithium-Sulfur Batteries

Functional separators, which are chemically modified and coated with nanostructured materials, are considered an effective and economical approach to suppressing the shuttle effect of lithium polysulfide (LiPS) and promoting the conversion kinetics of sulfur cathodes. Herein, we report cobalt-aluminum-layered double hydroxide quantum dots (LDH-QDs) deposited with nitrogen-doped graphene (NG) as a bifunctional separator for lithium-sulfur batteries (LSBs). The mesoporous LDH-QDs/NG hybrids possess abundant active sites of Co²⁺ and hydroxide groups, which result in capturing LiPSs through strong chemical interactions and accelerating the redox kinetics of the conversion reaction, as confirmed through X-ray photoelectron spectroscopy, adsorption tests, Li₂S nucleation tests, and electrokinetic analyses of the LiPS conversion. The resulting LDH-QDs/NG hybrid-coated polypropylene (LDH-QDs/NG/PP) separator, with an average thickness of ∼17 μm, has a high ionic conductivity of 2.67 mS cm^-1. Consequently, the LSB cells with the LDH-QDs/NG/PP separator can deliver a high discharge capacity of 1227.48 mAh g^-1 at 0.1C along with a low capacity decay rate of 0.041% per cycle over 1200 cycles at 1.0C.

Enhanced catalytic ozonation of ibuprofen using a 3D structured catalyst with MnO2 nanosheets on carbon microfibers

Heterogeneous catalytic ozonation is an effective approach to degrade refractory organic pollutants in water. However, ozonation catalysts with combined merits of high activity, good reusability and low cost for practical industrial applications are still rare. This study aims to develop an efficient, stable and economic ozonation catalyst for the degradation of Ibuprofen, a pharmaceutical compound frequently detected as a refractory pollutant in treated wastewaters. The novel three-dimensional network-structured catalyst, comprising of δ-MnO₂ nanosheets grown on woven carbon microfibers (MnO₂ nanosheets/carbon microfiber), was synthesized via a facile hydrothermal approach. Catalytic ozonation performance of Ibuprofen removal in water using the new catalyst proves a significant enhancement, where Ibuprofen removal efficiency of close to 90% was achieved with a catalyst loading of 1% (w/v). In contrast, conventional ozonation was only able to achieve 65% removal efficiency under the same operating condition. The enhanced performance with the new catalyst could be attributed to its significantly increased available surface active sites and improved mass transfer of reaction media, as a result of the special surface and structure properties of this new three-dimensional network-structured catalyst. Moreover, the new catalyst displays excellent stability and reusability for ibuprofen degradation over successive reaction cycles. The facile synthesis method and low-cost materials render the new catalyst high potential for industrial scaling up. With the combined advantages of high efficiency, high stability, and low cost, this study sheds new light for industrial applications of ozonation catalysts.

Strategy of Enhancing the Volumetric Energy Density for Lithium-Sulfur Batteries

Lithium-sulfur (Li-S) batteries hold the promise of the next generation energy storage system beyond state-of-the-art lithium-ion batteries. Despite the attractive gravimetric energy density (W_G ), the volumetric energy density (W_V ) still remains a great challenge for the practical application, based on the primary requirement of Small and Light for Li-S batteries. This review highlights the importance of cathode density, sulfur content, electroactivity in achieving high energy densities. In the first part, key factors are analyzed in a model on negative/positive ratio, cathode design, and electrolyte/sulfur ratio, orientated toward energy densities of 700 Wh L^-1 /500 Wh kg^-1 . Subsequently, recent progresses on enhancing W_V for coin/pouch cells are reviewed primarily on cathode. Especially, the "Three High One Low" (THOL) (high sulfur fraction, high sulfur loading, high density host, and low electrolyte quantity) is proposed as a feasible strategy for achieving high W_V , taking high W_G into consideration simultaneously. Meanwhile, host materials with desired catalytic activity should be paid more attention for fabricating high performance cathode. In the last part, key engineering technologies on manipulating the cathode porosity/density are discussed, including calendering and dry electrode coating. Finally, a future outlook is provided for enhancing both W_V and W_G of the Li-S batteries.

Cobalt Phosphide Nanoflake-Induced Flower-like Sulfur for High Redox Kinetics and Fast Ion Transfer in Lithium-Sulfur Batteries

Sulfur reactivity in lithium-sulfur batteries highly depends on its distribution and morphology during cycling, which is of great significance to suppress the shuttle effect and promote conversion reaction. Herein, cobalt phosphide nanoflakes are prepared and used as a sulfur host. An improved redox kinetics from sulfur to lithium sulfide and the corresponding fast lithium-ion diffusion are observed to greatly promote the electrochemical performance of lithium-sulfur batteries. Meanwhile, for the first time, we propose "effective triple phase contact" and "insulated dead sulfur" to account for cycling performance differences of CoP@S and rGO@S batteries. The flower-like sulfur induced by CoP nanoflakes during cycling provides extra lithium-ion diffusion and electron transfer ways compared with agglomerated sulfur in the rGO@S cathode. The CoP@S battery shows good rate performance and delivers 520 mA h g^-1 after 1000 cycles with an excellent Coulombic efficiency of 99%. In contrast, no conversion reaction happens after 600 cycles in the rGO@S battery, implying no existence of reactive sulfur. This research reveals the effect of morphological evolution of sulfur on the cycling performance and affords an insight for developing high-performance lithium-sulfur batteries.

A Perspective toward Practical Lithium-Sulfur Batteries

Lithium-sulfur (Li-S) batteries have long been expected to be a promising high-energy-density secondary battery system since their first prototype in the 1960s. During the past decade, great progress has been achieved in promoting the performances of Li-S batteries by addressing the challenges at the laboratory-level model systems. With growing attention paid to the application of Li-S batteries, new challenges at practical cell scales emerge as the bottleneck. In this Outlook, the key parameters for practical Li-S batteries to achieve practical high energy density are emphasized regarding high-sulfur-loading cathodes, lean electrolytes, and limited excess anodes. Subsequently, the key scientific problems are redefined in practical Li-S batteries beyond the previous ones under ideal conditions. Finally, viable strategies are proposed to address the above challenges as future research directions.

Inducing rapid polysulfide transformation through enhanced interfacial electronic interaction for lithium-sulfur batteries

Sluggish dynamics of polysulfide (LiPS) conversion leads to reduced utilization of active sulfur and rapid capacity decay. Introducing catalysts into lithium-sulfur battery systems is a feasible and imperative strategy to tackle this problem. Previous research studies have mainly been focused on selecting new catalysts and design functional structures to improve performance, and ignoring the interaction between catalysts and their carriers. Herein, by simply fabricating a high-efficiency ZnS quantum dot@graphene nanosheet catalyst (ZnS QD@rGO), we utilized enhanced interfacial electronic interaction to accelerate polysulfide conversion for high energy density Li-S batteries. With the smaller size of ZnS, the interfacial electronic interaction becomes more enhanced, which was evidenced by DFT calculations and XPS experiments. After mixing with sulfur, the electrodes achieved a high capacity of 857.8 mA h g^-1 at 1 C and a retention of 91.2% after 300 cycles. Also, a sulfur cathode with a high actual capacity of ∼4.0 mA h cm^-2 could be obtained, with no obvious capacity decay within 100 cycles. We believe that this strategy represents a new perspective on designing efficient high-load electrodes for Li-S batteries.

Single-atom Catalytic Materials for Lean-electrolyte Ultrastable Lithium-Sulfur Batteries

Lithium-sulfur batteries with high energy capacity are promising candidates for advanced energy storage. However, their applications are impeded by shuttling of soluble polysulfides and sluggish conversion kinetics with inferior rate performance and short cycling life. Here, single-atom materials are designed to accelerate polysulfide conversion for Li-S batteries. Nitrogen sites in the structure not only anchor polysulfides to alleviate the shuttle effect but also enable high loading of single-atom irons. Density functional theory calculations indicate that single-atom sites reduce the energy barrier of electrochemical reactions and thus improve the rate and cycling performances of batteries. The coin battery shows impressive energy storage properties, including a high reversible capacity of 1379 mAh g^-1 at 0.1 C and a high rate capacity of 704 mAh g^-1 at 5 C. The ratio of electrolyte dosage/energy density is as low as 5.5 g Ah^1-. It exhibits excellent cycling performance with a capacity retention of 90% even after 200 cycles at 0.2 C.

Electrocatalyzing S Cathodes via Multisulfiphilic Sites for Superior Room-Temperature Sodium-Sulfur Batteries

Room-temperature sodium-sulfur (RT-Na/S) batteries hold great promise for sustainable and cost-effective applications. Nevertheless, it remains a great challenge to achieve high capacity and cycling stability due to the low activity of sulfur and the sluggish conversion kinetics between polysulfide intermediates and sodium sulfide. Herein, an electrocatalyzing S cathode is fabricated, which consists of porous core-shell structure and multisulfiphilic sites. The flexible carbon structure effectively buffers volume changes during cycling and provides enclosed spaces to store S₈ with exceptional conductivity. Significantly, the multisulfiphilic sites (ZnS and CoS₂) enhance catalysis toward multistep S conversion, which effectively suppresses long-chain polysulfides dissolution and improves the kinetics of short-chain polysulfides. Thus, the obtained S cathodes achieve an enhanced cycling performance (570 mAh g^-1 at 0.2 A g^-1 over 1000 cycles), decent rate capability (250 mAh g^-1 at 1.0 A g^-1 over 2000 cycles), and high energy density of 384 Wh kg^-1 toward practical applications.

Interfacially Polymerized Polyamide Interlayer onto Ozonated Carbon Nanotube Networks for Improved Stability of Sulfur Cathodes

Lithium-sulfur (Li-S) batteries are considered promising energy-storage devices owing to the high specific capacity and low cost of the S cathode. However, they suffer from capacity decay and poor coulombic efficiency arising from the dissolution of long-chain polysulfides and their shuttling. A facile and scalable method was developed to directly coat a thin (≈57.3 nm) and porous polyamide (PA) interlayer onto a S cathode by interfacial polymerization. This PA interlayer prevented the shuttling of polysulfides by creating a physical barrier and, through chemical interactions between the amide functionalities of PA and the polysulfides, allowing access to the S electrode by the Li ions. The resulting PA-coated cathode exhibited approximately 64.2 % capacity retention over 1000 cycles at 1 C with only 0.0358 % decay per cycle and a moderate capacity of 1008 mAh g^-1 at 0.1 C.

B,N Codoped Graphitic Nanotubes Loaded with Co Nanoparticles as Superior Sulfur Host for Advanced Li-S Batteries

Lithium-sulfur batteries (LSBs) are considered as one of the best candidates for novel rechargeable batteries due to their high energy densities and abundant required materials. However, the poor conductivity and large volume expansion of sulfur and the "shuttle effect" of lithium polysulfides (LPSs) have significantly hindered the development and successful commercialization of LSBs. Bean-like B,N codoped carbon nanotubes loaded with Co nanoparticles (Co@BNTs), which can act as advanced sulfur hosts for the novel LSB cathode, are fabricated. Uniform graphitic nanotubes improve the conductivity of the electrode and load more electroactive sulfur and buffer volume expansion during the electrochemical reaction. In addition, loaded Co nanoparticles and codoped B,N sites can significantly suppress the "shuttle effect" of LPSs with strong chemical interaction. It is established that the Co nanoparticles and codoped B,N can provide more active sites to catalyze the redox reaction of sulfur cathode. This stable Co@BNTs-S cathode displays an exceptional electrochemical performance (1160 mA h g^-1 after 200 cycles at 0.1 C) and outstanding stable cycle performance (1008 mA h g^-1 after 400 cycles at 1.0 C with an extremely low attenuation rate of 0.038% per cycle).

Design Multifunctional Catalytic Interface: Toward Regulation of Polysulfide and Li2 S Redox Conversion in Li-S Batteries

The polysulfide shuttle effect and sluggish reaction kinetics hamper the practical applications of lithium-sulfur (Li-S) batteries. Incorporating a functional interlayer to trapping and binding polysulfides has been found effective to block polysulfide migration. Furthermore, surface chemistry at soluble polysulfides/electrolyte interface is a crucial step for Li-S battery in which stable cycling depends on adsorption and reutilization of blocked polysulfides in the electrolyte. A multifunctional catalytic interface composed of niobium nitride/N-doped graphene (NbN/NG) along the soluble polysulfides/electrolyte is designed and constructed to regulate corresponding interface chemical reaction, which can afford long-range electron transfer surfaces, numerous strong chemisorption, and catalytic sites in a working lithium-sulfur battery. Both experimental and theoretical calculation results suggest that a new catalytic interface enabled by metal-like NbN with superb electrocatalysis anchored on NG is highly effective in regulating the blocked polysulfide redox reaction and tailoring the Li₂ S nucleation-growth-decomposition process. Therefore, the Li-S batteries with multifunctional NbN/NG barrier exhibit excellent rate performance (621.2 mAh g^-1 at 3 C) and high stable cycling life (81.5% capacity retention after 400 cycles). This work provides new insights to promote Li-S batteries via multifunctional catalytic interface engineering.

Recent Advances of Porous Graphene: Synthesis, Functionalization, and Electrochemical Applications

Graphene is a 2D sheet of sp² bonded carbon atoms and tends to aggregate together, due to the strong π-π stacking and van der Waals attraction between different layers. Its unique properties such as a high specific surface area and a fast mass transport rate are severely blocked. To address these issues, various kinds of 2D holey graphene and 3D porous graphene are either self-assembled from graphene layers or fabricated using graphene related materials such as graphene oxide and reduced graphene oxide. Porous graphene not only possesses unique pore structures, but also introduces abundant exposed edges and accelerates mass transfer. The properties and applications of these porous graphenes and their composites/hybrids have been extensively studied in recent years. Herein, recent progress and achievements in synthesis and functionalization of various 2D holey graphene and 3D porous graphene are reviewed. Of special interest, electrochemical applications of porous graphene and its hybrids in the fields of electrochemical sensing, electrocatalysis, and electrochemical energy storage, are highlighted. As the closing remarks, the challenges and opportunities for the future research of porous graphene and its composites are discussed and outlined.

Highly Ordered Graphene Solid: An Efficient Platform for Capacitive Sodium-Ion Storage with Ultrahigh Volumetric Capacity and Superior Rate Capability

As an emerging type of electrochemical energy storage devices, sodium-ion capacitors (SICs) are potentially capable of high energy density and high power density, as well as low cost and long lifespan. Unfortunately, the lack of high-performance capacitive cathodes that can fully couple with the well-developed battery-type anodes severely restricts the further development of SICs. Here, we develop a compact yet highly ordered graphene solid (HOGS), which combines the merits of high density and high porosity and, more attractively, possesses a highly ordered lamellar texture with low pore tortuosity. As the capacitive cathode of SICs,  HOGS delivers a record-high volumetric capacity (303 F cm^-3 or 219 mA h cm^-3 at 0.05 A g^-1), a superior rate capability (185 F cm^-3 or 139 mA h cm^-3 even at 10 A g^-1), and an outstanding cycling stability (over 80% after 10 000 cycles). The material design and construction strategies reported here can be easily extended to other metal-ion-based energy storage technologies, exhibiting universal potentials in compact electrochemical energy storage systems.