Solution Plasma Process-Derived Defect-Induced Heterophase Anatase/Brookite TiO2 Nanocrystals for Enhanced Gaseous Photocatalytic Performance

Synergistic effect of Ag decorated in-liquid plasma treated titanium dioxide catalyst for efficient electrocatalytic CO2 reduction application

Recently, the conversion of carbon dioxide (CO2) into a useful resource and its byproducts by electrocatalytic reduction has been studied. It is well known that CO2 can be selectively reduced by gold, lead, etc. supported on conductive carbon. However, the high pH in the vicinity of the electrode raises concerns about the catalyst and catalyst support degradation. Therefore, we considered that using chemically stable TiO2 (titanium dioxide) powder as an alternative to carbon. Surface treatment using in-liquid plasma was used to improve the electrochemical properties of TiO2. TiO2 maintained its particle shape and crystalline structure after in-liquid plasma treatment. Electrochemical properties were evaluated and the disappearance of Ti4+ and Ti3+ redox peaks derived from TiO2 and a decrease in hydrogen overvoltage were observed. The hydrogen overvoltage relationship suggested that tungsten coating or doping on a portion of the reduced TiO2 surface. Electrocatalytic CO2 reduction using the silver nanoparticle-supported in-liquid plasma treated TiO2 showed increased hydrogen production. In electrocatalytic CO2 reduction, the ratio of hydrogen to carbon monoxide gas is important. Therefore, in-liquid plasma treated TiO2 is useful for the electrocatalytic CO2 reduction application.

Solution plasma synthesis of Pt-decorated Bi12O17Cl2 photocatalysts for efficient upcycling of plastics

Photocatalytic upcycling of plastic waste is a promising approach to relieving pressure caused by solid waste, but the rational design of novel efficient photocatalysts remains a challenge. Herein, we utilize subnano-sized platinum (Pt)-based photocatalysts for plastic upcycling. A solution plasma strategy is developed to fabricate Pt-decorated Bi12O17Cl2 (SP-BOC). The Pt in an oxidant state and oxygen vacancies optimize the electronic structure for fast charge transfer. As a result, SP-BOC displays high performance for upcycling polyvinyl chloride (PVC) and polylactic acid (PLA) into acetic acid and formic acid, with yield rate and selectivity of 6.07 mg g-1cat. h-1 and 94 %, and 47.43 mg g-1cat. h-1 and 55.1 %, respectively. In addition, the dichlorination efficiency of PVC reaches 78.1 % within 10 h reaction, effectively reducing the environmental hazards associated with PVC waste disposal treatments. This research provides insight into the effective conversion of plastics into high-value chemicals, contributing to the reduction of carbon and toxic emissions in a practical and meaningful way, and offering a useful way for solving challenges of waste management and environmental sustainability.

Biofunctionalized CdS Quantum Dots: A Case Study on Nanomaterial Toxicity in the Photocatalytic Wastewater Treatment Process

The toxic nature of inorganic nanostructured materials as photocatalysts is often not accounted for in traditional wastewater treatment reactions. Particularly, some inorganic nanomaterials employed as photocatalysts may release secondary pollutants in the form of ionic species that leach out due to photocorrosion. In this context, this work is a proof-of-concept study for exploring the environmental toxicity effect of extremely small-sized nanoparticles (<10 nm) like quantum dots (QDs) that are employed as photocatalysts, and in this study, cadmium sulfide (CdS) QDs are chosen. Typically, CdS is an excellent semiconductor with suitable bandgap and band-edge positions that is attractive for applications in solar cells, photocatalysis, and bioimaging. However, the leaching of toxic cadmium (Cd²⁺) metal ions due to the poor photocorrosion stability of CdS is a matter of serious concern. Therefore, in this report, a cost-effective strategy is devised for biofunctionalizing the active surface of CdS QDs by employing tea leaf extract, which is expected to hinder photocorrosion and prevent the leaching of toxic Cd²⁺ ions. The coating of tea leaf moieties (chlorophyll and polyphenol) over the CdS QDs (referred to hereafter as G-CdS QDs) was confirmed through structural, morphological, and chemical analysis. Moreover, the enhanced visible-light absorption and emission intensity of G-CdS QDs in comparison to that of C-CdS QDs synthesized through a conventional chemical synthesis approach confirmed the presence of chlorophyll/polyphenol coating. Interestingly, the polyphenol/chlorophyll molecules formed a heterojunction with CdS QDs and enabled the G-CdS QDs to exhibit enhanced photocatalytic activity in the degradation of methylene blue dye molecules over C-CdS QDs while effectively preventing photocorrosion as confirmed from cyclic photodegradation studies. Furthermore, detailed toxicity studies were conducted by exposing zebrafish embryos to the as-synthesized CdS QDs for 72 h. Surprisingly, the survival rate of the zebrafish embryos exposed to G-CdS QDs was equal to that of the control, indicating a significant reduction in the leaching of Cd²⁺ ions from G-CdS QDs in comparison to C-CdS QDs. The chemical environment of C-CdS and G-CdS before and after the photocatalysis reaction was examined by X-ray photoelectron spectroscopy. These experimental findings prove that biocompatibility and toxicity could be controlled by simply adding tea leaf extract during the synthesis of nanostructured materials, and revisiting green synthesis techniques can be beneficial. Furthermore, repurposing the discarded tea leaves may not only facilitate the control of toxicity of inorganic nanostructured materials but can also help in enhancing global environmental sustainability.

Ethanol Solution Plasma Loads Carbon Dots onto 2D HNb3O8 for Enhanced Photocatalysis

Layered metal oxoacids hold potential as photocatalysts due to their facile exfoliation to two-dimensional (2D) nanosheets with a large surface area and a short migration distance for photoexcited charge carriers. However, the utilization of electrons in photocatalytic processes is restricted by the competitive trapping of electrons by metal ions. In this work, we attempt to improve the utilization of photogenerated electrons over exfoliated HNb₃O₈ nanosheets by solution plasma activation. On dispersing exfoliated HNb₃O₈ nanosheets in ethanol solution plasma, the defects in HNb₃O₈ can be engineered, and carbon dots (CDs) can be anchored on the surface of HNb₃O₈ nanosheets in situ. In comparison with pristine HNb₃O₈ nanosheets, the rate of photocatalytic hydrogen evolution can be increased by 317.7 times over the HNb₃O₈/C heterojunction, and the apparent quantum efficiency of hydrogen production can be as high as 5.05%. The reason for the high photocatalytic performance is explored by the comparison of activation between plasma-in-ethanol and plasma-in-water, which reveals that CD anchoring and defect engineering indeed promote charge separation and hence lead to enhanced photocatalytic activity. This work provides an alternative approach to synthesize CDs and activate 2D-layered compounds with MO₆ (M = Nb, Ti, and W) octahedral building blocks in the host layer for enhanced photocatalytic evolution of hydrogen.

Impact of TiO2 Reduction and Cu Doping on Bacteria Inactivation under Artificial Solar Light Irradiation

Preparation of TiO₂ using the hydrothermal treatment in NH₄OH solution and subsequent thermal heating at 500-700 °C in Ar was performed in order to introduce some titania surface defects. The highest amount of oxygen vacancies and Ti³⁺ surface defects were observed for a sample heat-treated at 500 °C. The presence of these surface defects enhanced photocatalytic properties of titania towards the deactivation of two bacteria species, E. coli and S. epidermidis, under artificial solar lamp irradiation. Further modification of TiO₂ was targeted towards the doping of Cu species. Cu doping was realized through the impregnation of the titania surface by Cu species supplied from various copper salts in an aqueous solution and the subsequent heating at 500 °C in Ar. The following precursors were used as a source of Cu: CuSO₄, CuNO₃ or Cu(CH₃COO)₂. Cu doping was performed for raw TiO₂ after a hydrothermal process with and without NH₄OH addition. The obtained results indicate that Cu species were deposited on the titania surface defects in the case of reduced TiO₂, but on the TiO₂ without NH₄OH modification, Cu species were attached through the titania adsorbed hydroxyl groups. Cu doping on TiO₂ increased the absorption of light in the visible range. Rapid inactivation of E. coli within 30 min was obtained for the ammonia-reduced TiO₂ heated at 500 °C and TiO₂ doped with Cu from CuSO₄ solution. Photocatalytic deactivation of S. epidermidis was greatly enhanced through Cu doping on TiO₂. Impregnation of TiO₂ with CuSO₄ was the most effective for inactivation of both E. coli and S. epidermidis.

Impact of TiO2 Surface Defects on the Mechanism of Acetaldehyde Decomposition under Irradiation of a Fluorescent Lamp

TiO2 was placed in heat-treatment at the temperature of 400–500 °C under flow of hydrogen gas in order to introduce some titania surface defects. It was observed that hole centers in TiO2 were created during its heat treatment up to 450 °C, whereas at 500 °C some Ti3+ electron surface defects appeared. The type of titania surface defects had a great impact on the mechanism of acetaldehyde decomposition under irradiation of artificial visible light. Formation of O•− defects improved both acetaldehyde decomposition and mineralization due to the increased oxidation of adsorbed acetaldehyde molecules by holes. Contrary to that, the presence of electron traps and oxygen vacancies in titania (Ti3+ centers) was detrimental for its photocatalytic properties towards acetaldehyde decomposition. It was proved that transformation of acetaldehyde on the TiO2 with Ti3+ defects proceeded through formation of butene complexes, similar as on rutile-type TiO2. Formed acetic acid, upon further oxidation of butene complexes, was strongly bound with the titania surface and showed high stability under photocatalytic process. Therefore, titania sample heat-treated with H2 at 500 °C showed much lower photocatalytic activity than that prepared at 450 °C. This study indicated the great impact of titania surface defects (hole traps) in the oxidation of acetaldehyde and opposed one in the case of defects in the form of Ti3+ and oxygen vacancies. Oxidation abilities of TiO2 seem to be important in the photocatalytic decomposition of volatile organic compounds (VOCs) such as acetaldehyde.

Reversed Charge Transfer and Enhanced Hydrogen Spillover in Platinum Nanoclusters Anchored on Titanium Oxide with Rich Oxygen Vacancies Boost Hydrogen Evolution Reaction

The catalytic activity of metal clusters is closely related with the support; however, knowledge on the influence of the support on the catalytic activity is scarce. We demonstrate that Pt nanoclusters (NCs) anchored on porous TiO₂ nanosheets with rich oxygen vacancies (V_O -rich Pt/TiO₂ ) and deficient oxygen vacancies (V_O -deficient Pt/TiO₂ ), display significantly different catalytic activity for the hydrogen evolution reaction (HER), in which V_O -rich Pt/TiO₂ shows a mass activity of 45.28 A mg_Pt ^-1 at -0.1 V vs. RHE, which is 16.7 and 58.8 times higher than those of V_O -deficient Pt/TiO₂ and commercial Pt/C, respectively. DFT calculations and in situ Raman spectra suggest that porous TiO₂ with rich oxygen vacancies can simultaneously achieve reversed charge transfer (electrons transfer from TiO₂ to Pt NCs) and enhanced hydrogen spillover from Pt NCs to the TiO₂ support, which leads to electron-rich Pt NCs being amenable to proton reduction of absorbed H*, as well as the acceleration of hydrogen desorption at Pt catalytic sites-both promoting the HER. Our work provides a new strategy for rational design of highly efficient HER catalysts.

Indoor gas phase photoactivity of yttrium modified titanate films for fast acetaldehyde oxidation

Photoactive materials hold structural and catalytic features that make them particularly suitable for environmental applications and in the present work, protonated H₃Ti₃O₇-Y nanofiber-like materials were prepared via the microwave assisted hydrothermal technique. The as-prepared nanofibers exhibited high surface area with titanate structure. The nanofibers, before and after yttrium incorporation, were well-distributed and the fibrous morphology could be observed clearly; as the yttrium loading increased, ribbons and the anatase phase were formed. Practical films of these nanofibers confirmed their likely UV-photoactive properties with 200 ppm of acetaldehyde degradation within 25 min in the presence of 50% of humidity. Activity retention was achieved, keeping stability for 2 consecutive cycles at room temperature. Nowadays, the increase in home office work sets human health at risk, for the exposure to toxic volatile organic compounds and microorganisms such as viruses and bacteria is more frequent indoors. In this context, the synthesized photoactive yttrium-titanate films stand as upcoming practical UV-driven materials for cleaning pollution that concentrated urban activity and indoor environments.

Photocatalytic Decomposition of Acetaldehyde on Different TiO2-Based Materials: A Review

Purification of air from the organic contaminants by the photocatalytic process has been confirmed to be very perspective. Although many various photocatalysts have been prepared and studied so far, TiO2 is still the most commonly used, because of its advantageous properties such as non-toxicity, relatively low cost and high stability. Surface modifications of TiO2 were extensively proceeded in order to increase photocatalytic activity of the photocatalyst under both UV and visible light activations. The intention of this review paper was to summarize the scientific achievements devoted to developing of TiO2-based materials considered as photocatalysts for the photocatalytic degradation of acetaldehyde in air. Influence of the preparation and modification methods on the parameters of the resultant photocatalyst is reviewed and discussed in this work. Affinity of the photocatalyst surfaces towards adsorption of acetaldehyde will be described by taking into account its physicochemical parameters. Impact of the contact time of a pollutant with the photocatalyst surface is analyzed and discussed with respect to both the degradation rate and mineralization degree of the contaminant. Influence of the photocatalyst properties on the mechanism and yield of the photocatalytic reactions is discussed. New data related to the acetaldehyde decomposition on commercial TiO2 were added, which indicated the different mechanisms occurring on the anatase and rutile structures. Finally, possible applications of the materials revealing photocatalytic activity are presented with a special attention paid to the photocatalytic purification of air from Volatile Organic Compounds (VOCs).

Enhanced Solar Photothermal Catalysis over Solution Plasma Activated TiO2

Colored wide-bandgap semiconductor oxides with abundant mid-gap states have long been regarded as promising visible light responsive photocatalysts. However, their catalytic activities are hampered by charge recombination at deep level defects, which constitutes the critical challenge to practical applications of these oxide photocatalysts. To address the challenge, a strategy is proposed here that includes creating shallow-level defects above the deep-level defects and thermal activating the migration of trapped electrons out of the deep-level defects via these shallow defects. A simple and scalable solution plasma processing (SPP) technique is developed to process the presynthesized yellow TiO₂ with numerous oxygen vacancies (Ov), which incorporates hydrogen dopants into the TiO₂ lattice and creates shallow-level defects above deep level of Ov, meanwhile retaining the original visible absorption of the colored TiO₂. At elevated temperature, the SPP-treated TiO₂ exhibits a 300 times higher conversion rate for CO₂ reduction under solar light irradiation and a 7.5 times higher removal rate of acetaldehyde under UV light irradiation, suggesting the effectiveness of the proposed strategy to enhance the photoactivity of colored wide-bandgap oxides for energy and environmental applications.

Enhanced Solar Photothermal Catalysis over Solution Plasma Activated TiO2

Colored wide-bandgap semiconductor oxides with abundant mid-gap states have long been regarded as promising visible light responsive photocatalysts. However, their catalytic activities are hampered by charge recombination at deep level defects, which constitutes the critical challenge to practical applications of these oxide photocatalysts. To address the challenge, a strategy is proposed here that includes creating shallow-level defects above the deep-level defects and thermal activating the migration of trapped electrons out of the deep-level defects via these shallow defects. A simple and scalable solution plasma processing (SPP) technique is developed to process the presynthesized yellow TiO2 with numerous oxygen vacancies (Ov), which incorporates hydrogen dopants into the TiO2 lattice and creates shallow-level defects above deep level of Ov, meanwhile retaining the original visible absorption of the colored TiO2. At elevated temperature, the SPP-treated TiO2 exhibits a 300 times higher conversion rate for CO2 reduction under solar light irradiation and a 7.5 times higher removal rate of acetaldehyde under UV light irradiation, suggesting the effectiveness of the proposed strategy to enhance the photoactivity of colored wide-bandgap oxides for energy and environmental applications.

DC-Plasma over Aqueous Solution for the Synthesis of Titanium Dioxide Nanoparticles under Pressurized Argon

Nanomaterials that comprise titanium dioxide (TiO2) nanoparticles have received much attention owing to their wide applications; presently, the green synthesis of TiO2 nanoparticles is a developing research area. In this study, the TiO2 nanoparticles were synthesized through a DC-pulsed discharge plasma over an aqueous solution surface under a high-pressure argon environment. The titanium-rod electrode was utilized as the material source for the TiO2 nanoparticle generation. Experiments were performed at room temperature with pressurized argon at 1-4 MPa. To generate a pulse electrical discharge plasma, a DC power supply of 18.6 kV was applied. The Raman spectroscopy showed that the TiO2 nanoparticle with a brookite structure was formed dominantly. The scanning transmission electron microscopy equipped with energy dispersion spectroscopy (STEM coupled with EDS) indicated that TiO2 coated with carbon and that without carbon coating were successfully produced at the nanoscale. The process presented here is an innovative process and can update the existing information regarding the synthesis of metal-based nanoparticles using pulsed discharge plasma under an argon environment.

Defects-Induced In-Plane Heterophase in Cobalt Oxide Nanosheets for Oxygen Evolution Reaction

Cobalt oxides as efficient oxygen evolution reaction (OER) electrocatalysts have received much attention because of their rich reserves and cheap cost. There are two common cobalt oxides, Co₃ O₄ (spinel phase, stable but poor intrinsic activity) and CoO (rocksalt phase, active but easily be oxidatized). Constructing Co₃ O₄ /CoO heterophase can inherit both characteristic features of each component and form a heterophase interface facilitating charge transfer, which is believed to be an effective strategy in designing excellent electrocatalysts. Herein, an atomic arrangement engineering strategy is applied to improve electrocatalytic activity of Co₃ O₄ for the OER. With the presence of oxygen vacancies, cobalt atoms at tetrahedral sites in Co₃ O₄ can more easily diffuse into interstitial octahedral sites to form CoO phase structure as revealed by periodic density functional theory computations. The Co₃ O₄ /CoO spinel/rocksalt heterophase can be in situ fabricated at the atomic scale in plane. The overpotential to reach 10 mA cm^-2 of Co₃ O₄ /CoO is 1.532 V, which is 92 mV smaller than that of Co₃ O₄ . Theoretical calculations confirm that the excellent electrochemical activity is corresponding to a decline in average p-state energy of adsorbed-O on the Co₃ O₄ /CoO heterophase interface. The reaction Gibbs energy barrier has been significantly decreased with the construction of the heterophase interface.

Transition-Metal Ion-Doped Flower-Like Titania Nanospheres as Nonlight-Driven Catalysts for Organic Dye Degradation with Enhanced Performances

Titania has recently been identified as a new and effective nonlight-driven catalyst for degradation of organic pollutant with the use of H₂O₂ as an oxidant; however, either relatively low surface area or lack of diversity in chemical composition largely limits its catalytic performance. In this work, a series of transition-metal ion (Mn²⁺, Co²⁺, Ni²⁺, and Cu²⁺)-doped titania nanomaterials with regular flower-like morphology, good crystallinity (anatase), and large specific surface areas (71.4-124.4 m² g^-1) were facilely synthesized and utilized as catalysts for methylene blue (MB) degradation in the presence of H₂O₂ without light irradiation. It was revealed that the doping of transition-metal ions (especially Mn²⁺) into titania could significantly improve the catalytic efficiency. At 30 °C, 10 mL of MB with a concentration of 50 mg L^-1 could be completely degraded within 60-100 min for these doped samples, whereas the removal rate was only 35.1% within 100 min with the use of pure flower-like titania. Temperature-dependent kinetic studies indicated that the presence of transition-metal ion dopants could markedly lower the activation energy and thus resulted in enhanced catalytic performances. Test of reusability exhibited that these doped catalysts could well keep their original catalytic activities after reuse for several cycles, indicating their excellent catalytic durability.

Electrochemically Treated TiO₂ for Enhanced Performance in Aqueous Al-Ion Batteries

The potential for low cost, environmentally friendly and high rate energy storage has led to the study of anatase-TiO₂ as an electrode material in aqueous Al3+ electrolytes. This paper describes the improved performance from an electrochemically treated composite TiO₂ electrode for use in aqueous Al-ion batteries. After application of the cathodic electrochemical treatment in 1 mol/dm³ KOH, Mott⁻Schottky analysis showed the treated electrode as having an increased electron density and an altered open circuit potential, which remained stable throughout cycling. The cathodic treatment also resulted in a change in colour of TiO₂. Treated-TiO₂ demonstrated improved capacity, coulombic efficiency and stability when galvanostatically cycled in 1 mol·dm-3AlCl₃/1 mol·dm-3 KCl. A treated-TiO₂ electrode produced a capacity of 15.3 mA·h·g-1 with 99.95% coulombic efficiency at the high specific current of 10 A/g. Additionally, X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy were employed to elucidate the origin of this improved performance.