Hand-Held Transistor Based Electrical and Multiplexed Chemical Sensing System

Portable Measurement System for the Characterization of Capacitive Field-Effect Sensors

A user-friendly, portable, low-cost readout system for the on-site or point-of-care characterization of chemo- and biosensors based on an electrolyte-insulator-semiconductor capacitor (EISCAP) has been developed using a thumb-drive-sized commercial impedance analyzer. The system is controlled by a custom Python script and allows to characterize EISCAP sensors with different methods (impedance spectra, capacitance-voltage, and constant-capacitance modes), which are selected in a user interface. The performance of the portable readout system was evaluated by pH measurements and the detection of the antibiotic penicillin, hereby using EISCAPs consisting of Al/p-Si/SiO2/Ta2O5 structures and compared to the results obtained with a stationary commercial impedance analyzer. Both the portable and the commercial systems provide very similar results with almost perfectly overlapping recorded EISCAP signals. The new portable system can accelerate the transition of EISCAP sensors from research laboratories to commercial end-user devices.

Accelerating the Understanding of Biosensors Through the Lens of Cells: State of the Field, Emerging Directions, Advances, and Challenges

Cell-based biosensors are evolving as versatile tools for biological research, drug development, and environmental monitoring. Living cells are used to detect elements in these biosensors, which offer significant advantages over standard transducers. The purpose of this review article is to provide an in-depth overview of cell-based biosensors, emphasizing their working principles, fabrication processes, and applications. The potential of living cells to respond to particular analytes or stimuli supports the design and operation of cell-based biosensors. Real-time and label-free identification can be accomplished by combining these cells with transducers like microelectrodes or optical sensors. Genetically engineered cells or changed microenvironments can be used in cell-based biosensors to improve performance by optimizing cell types for increased dynamic range, sensitivity, and selectivity. Cell-based biosensors are developed by meticulously cultivating and immobilizing cells on transducer surfaces while retaining their vitality and performance. Cell-based biosensors have a wide range of applications, including monitoring the environment, healthcare, and pharmaceutical research. These biosensors have been used to detect diseases, toxic substances, pollutants, and therapeutic drug screening. Cell-based biosensors are cutting-edge technology that brings together the capabilities of live cells and transducers to detect analytes in a sensitive and specific manner. These biosensors illustrate the tremendous potential for upcoming uses in healthcare and monitoring environmental conditions with further developments in fabrication methods and the inclusion of artificial intelligence.

Methods gold standard in clinic millifluidics multiplexed extended gate field-effect transistor biosensor with gold nanoantennae as signal amplifiers

We present a portable multiplexed biosensor platform based on the extended gate field-effect transistor and demonstrate its amplified response thanks to gold nanoparticle-based bioconjugates introduced as a part of the immunoassay. The platform comprises a disposable chip hosting an array of 32 extended gate electrodes, a readout module based on a single transistor operating in constant charge mode, and a multiplexer to scan sensing electrodes one-by-one. Although employing only off-the-shelf electronic components, our platform achieves sensitivities comparable to fully customized nanofabricated potentiometric sensors. In particular, it reaches a detection limit of 0.2 fM for the pure molecular assay when sensing horseradish peroxidase-linked secondary antibody (∼0.4 nM reached by standard microplate methods). Furthermore, with the gold nanoparticle bioconjugation format, we demonstrate ca. 5-fold amplification of the potentiometric response compared to a pure molecular assay, at the detection limit of 13.3 fM. Finally, we elaborate on the mechanism of this amplification and propose that nanoparticle-mediated disruption of the diffusion barrier layer is the main contributor to the potentiometric signal enhancement. These results show the great potential of our portable, sensitive, and cost-efficient biosensor for multidimensional diagnostics in the clinical and laboratory settings, including e.g., serological tests or pathogen screening.

Enhancing the repeatability and sensitivity of low-cost PCB, pH-sensitive field-effect transistors

Discrete, extended gate pH-sensitive field-effect transistors (dEGFETs) fabricated on printed circuit boards (PCBs) are a low-cost, simple to manufacture analytical technology that can be applied to a wide range of applications. Electrodeposited iridium oxide (IrOx) films have emerged as promising pH-sensitive layers owing to their theoretically high pH sensitivity and facile deposition, but typically exhibit low pH sensitivity or lack reproducibility. Moreover, to date, a combined IrOx and dEGFET PCB system has not yet been realised. In this study, we demonstrate a dEGFET pH sensor based on an extended gate manufactured on PCB that is rendered pH sensitive through an electrodeposited IrOx film, which can reliably and repeatably display beyond-Nernstian pH response. Using a combination of complementary surface analysis techniques, we show that the high pH sensitivity and repeatability of the dEGFETs are dependent on both the chemical composition and critically the uniformity of the IrOx film. The IrOx film uniformity can be enhanced through electrochemical polishing of the extended gate electrode prior to electrodeposition, leading to dEGFETs that exhibit a median pH sensitivity of 70.7 ± 5 mV/pH (n = 56) compared to only 31.3 ± 14 mV/pH (n = 31) for IrOx electrodeposited on non-polished PCB electrodes. Finally, we demonstrate the applicability of these devices by demonstrating the detection and quantification of ampicillin due to β-Lactamase enzyme activity, thus laying the foundation for cheap and ubiquitous sensors which can be applied to a range of global challenges across healthcare and environmental monitoring.

Biological and technical challenges for implementation of yeast-based biosensors

Biosensors are low-cost and low-maintenance alternatives to conventional analytical techniques for biomedical, industrial and environmental applications. Biosensors based on whole microorganisms can be genetically engineered to attain high sensitivity and specificity for the detection of selected analytes. While bacteria-based biosensors have been extensively reported, there is a recent interest in yeast-based biosensors, combining the microbial with the eukaryotic advantages, including possession of specific receptors, stability and high robustness. Here, we describe recently reported yeast-based biosensors highlighting their biological and technical features together with their status of development, that is, laboratory or prototype. Notably, most yeast-based biosensors are still in the early developmental stage, with only a few prototypes tested for real applications. Open challenges, including systematic use of advanced molecular and biotechnological tools, bioprospecting, and implementation of yeast-based biosensors in electrochemical setup, are discussed to find possible solutions for overcoming bottlenecks and promote real-world application of yeast-based biosensors.

A Bioinspired Artificial Gustatory Neuron for a Neuromorphic Based Electronic Tongue

A novel biomimicked neuromorphic sensor for an energy efficient and highly scalable electronic tongue (E-tongue) is demonstrated with a metal-oxide-semiconductor field-effect transistor (MOSFET). By mimicking a biological gustatory neuron, the proposed E-tongue can simultaneously detect ion concentrations of chemicals on an extended gate and encode spike signals on the MOSFET, which acts as an input neuron in a spiking neural network (SNN). Such in-sensor neuromorphic functioning can reduce the energy and area consumption of the conventional E-tongue hardware. pH-sensitive and sodium-sensitive artificial gustatory neurons are implemented by using two different sensing materials: Al₂O₃ for pH sensing and sodium ionophore X for sodium ion sensing. In addition, a sensitivity control function inspired by the biological sensory neuron is demonstrated. After the unit device characterization of the artificial gustatory neuron, a fully hardware-based E-tongue that can classify two distinct liquids is demonstrated to show a practical application of the artificial gustatory neurons.

Nanomaterials for IoT Sensing Platforms and Point-of-Care Applications in South Korea

Herein, state-of-the-art research advances in South Korea regarding the development of chemical sensing materials and fully integrated Internet of Things (IoT) sensing platforms were comprehensively reviewed for verifying the applicability of such sensing systems in point-of-care testing (POCT). Various organic/inorganic nanomaterials were synthesized and characterized to understand their fundamental chemical sensing mechanisms upon exposure to target analytes. Moreover, the applicability of nanomaterials integrated with IoT-based signal transducers for the real-time and on-site analysis of chemical species was verified. In this review, we focused on the development of noble nanostructures and signal transduction techniques for use in IoT sensing platforms, and based on their applications, such systems were classified into gas sensors, ion sensors, and biosensors. A future perspective for the development of chemical sensors was discussed for application to next-generation POCT systems that facilitate rapid and multiplexed screening of various analytes.

Nitrates in the environment: A critical review of their distribution, sensing techniques, ecological effects and remediation

Nitrate pollution is eminent in almost all the developing nations as a result of increased natural activities apart from anthropogenic pollution. The release of nitrates in more than critical quantities into the water bodies causes accretion impacts on living creatures, environmental receptors, and human vigour by accumulation through the food chain. Nitrates have recently acquired researchers' huge attention and extend their roots in environmental contamination of surface and groundwater systems. The presence of nitrate in high concentrations in surface and groundwater triggers several health problems, for instance, methemoglobinemia, diabetes, eruption of infectious disorders, harmfully influence aquatic organisms. Sensing nitrate is an alternate option for monitoring the distribution of nitrate in different water bodies. Here we review electrochemical, spectroscopic, and electrical modes of nitrate sensing. It is concluded that, among the various sensors discussed in this review, FET sensors are the most desirable choice. Their sensitivity, ease of use and scope for miniaturisation are exceptional. Advanced functional materials need to be designed to satiate the growing need for environmental monitoring. Different sources of nitrate contamination in ground and surface water can be estimated using different techniques such as nitrate isotopic composition, co contaminants, water tracers, and other specialized techniques. This review intends to explore the research work on remediation of nitrate from wastewater and soil using different processes such as reverse osmosis, chemical denitrification, biological denitrification, ion exchange, electrodialysis, and adsorption. Denitrification proves as a promising alternative over previously reported techniques in terms of their nitrate removal because of its high cost-effectiveness.

Open-Source Portable Device for the Determination of Fluoride in Drinking Water

The prolonged exposure to fluorides results in the development of several diseases, from dental fluorosis to crippling deformities of the spine and major joints. The population exposed to high fluoride concentration is located in developing countries where the assurance of water quality is difficult to perform. Addressing this challenge, an open-source system for the determination of fluoride in natural water was developed using the equilibrium between the red Fe-SCN complex and the colorless Fe-F. The reaction develops in cotton substrates to reduce the manipulation of liquid reagents and reduce the errors by nontrained operators. The system was optimized by image analysis and implemented in an open-source Arduino-based device and data was acquired through the serial port of a cell phone, which is also used as a power source, avoiding the use of a battery and reducing production costs. The device showed a detection limit of 0.7 mg L^-1 and a linear range of up to 8 mg L^-1. This extended detection limit makes the device useful for the application in regions where the fluoride concentration in drinking water is far higher than the United Nations limit (1.5 mg L^-1), e.g., the United Republic of Tanzania, where the upper limit of F^- was extended to 4 mg L^-1 or in USA, where the Environmental Protection Agency established the Maximum Contaminant Level of F^- in drinking water at 4 mg L^-1. The method was tested with natural waters from the Arusha region in the northeast of Tanzania and validated against the results from ion chromatography showing a good correlation. The developed device exhibits chemical stability of 5 days, allowing it to be manufactured and distributed in local areas and, also, modified according to the requirements of the water composition due to Industry 4.0 concepts used in the design.

Comparison of the Extended Gate Field-Effect Transistor with Direct Potentiometric Sensing for Super-Nernstian InN/InGaN Quantum Dots

We systematically study the sensitivity and noise of an InN/InGaN quantum dot (QD) extended gate field-effect transistor (EGFET) with super-Nernstian sensitivity and directly compare the performance with potentiometric sensing. The QD sensor exhibits a sensitivity of -80 mV/decade with excellent linearity over a wide concentration range, assessed for chloride anion detection in 10^-4 to 0.1 M KCl aqueous solutions. The sensitivity and linearity are reproduced for the EGFET and direct open-circuit potential (OCP) readout. The EGFET noise in the saturated regime is smaller than the OCP noise, while the EGFET noise in the linear regime is largest. This highlights EGFET operation in the saturated regime for most precise measurements and the lowest limit of detection and the lowest limit of quantification, which is attributed to the low-impedance current measurement at a relatively high bias and the large OCP for the InN/InGaN QDs.

Monitoring Chemistry In Situ with a Smart Stirrer: A Magnetic Stirrer Bar with an Integrated Process Monitoring System

Inspired by the miniaturization and efficiency of the sensors for telemetry, we have developed a device that provides the functionalities of laboratory magnetic stirring and integrated multisensor monitoring of various chemical reaction parameters. The device, called "Smart Stirrer", when immersed in a solution, can in situ monitor physical properties of the chemical reaction such as the temperature, conductivity, visible spectrum, opaqueness, stirring rate, and viscosity. This data is transmitted real-time over a wireless connection to an external system, such as a PC or smartphone. The flexible open-source software architecture allows effortless programming of the operation parameters of the Smart Stirrer in accordance with the end-user needs. The concept of the Smart Stirrer device with an integrated process monitoring system has been demonstrated in a series of experiments showing its capability for many hours of continuous telemetry with fine accuracy and a high data rate. Such a device can be used in conventional research laboratories, industrial production lines, flow reactors, and others where it can log the state of the process to ensure repeatability and operational consistency.

Endogenous Bioelectrics in Development, Cancer, and Regeneration: Drugs and Bioelectronic Devices as Electroceuticals for Regenerative Medicine

A major frontier in the post-genomic era is the investigation of the control of coordinated growth and three-dimensional form. Dynamic remodeling of complex organs in regulative embryogenesis, regeneration, and cancer reveals that cells and tissues make decisions that implement complex anatomical outcomes. It is now essential to understand not only the genetics that specifies cellular hardware but also the physiological software that implements tissue-level plasticity and robust morphogenesis. Here, we review recent discoveries about the endogenous mechanisms of bioelectrical communication among non-neural cells that enables them to cooperate in vivo. We discuss important advances in bioelectronics, as well as computational and pharmacological tools that are enabling the taming of biophysical controls toward applications in regenerative medicine and synthetic bioengineering.

Nanoscale FET-Based Transduction toward Sensitive Extended-Gate Biosensors

Owing to their simple and low-cost architecture, extended-gate biosensors based on the combination of a disposable sensing part and a reusable transducer have been widely utilized for the label-free electrical detection of chemical and biological species. Previous studies have demonstrated that sensitive and selective detection of ions and biomolecules can be achieved by controlled modification of the sensing part with an ion-selective membrane and receptors of interest. However, no systematic studies have been performed on the impact of the transducer on sensing performance. In this paper, we introduce the concept of a nanoscale field-effect transistor (FET) as a reusable and sensitive transducer for extended-gate biosensors. The capacitive effect from the external sensing part can degrade the sensing performance, but the nanoscale FET can reduce this effect. The nanoscale FET with a gate-all-around (GAA) structure exhibits a higher pH sensitivity than a commercially available FET, which is widely used in conventional extended-gate biosensors. A sensitivity reduction is observed for the commercial FET, whereas the pH sensitivity is insensitive to the area of the sensing region in the nanoscale FET, thus allowing the scaling of the detection area. Our analysis based on a capacitive model suggests that the high pH sensitivity in the compact sensing area originates from the small input capacitance of the nanoscale FET transducer. Moreover, a decrease in the nanowire width of the GAA FET leads to an improvement in the pH sensitivity. The extended-gate approach with the nanoscale FET-based transduction can pave the way for a highly sensitive analysis of chemical and biological species with a small sample volume.

Deep Submicron EGFET Based on Transistor Association Technique for Chemical Sensing

Extended-gate field-effect transistor (EGFET) is an electronic interface originally developed as a substitute for an ion-sensitive field-effect transistor (ISFET). Although the literature shows that commercial off-the-shelf components are widely used for biosensor fabrication, studies on electronic interfaces are still scarce (e.g., noise processes, scaling). Therefore, the incorporation of a custom EGFET can lead to biosensors with optimized performance. In this paper, the design and characterization of a transistor association (TA)-based EGFET was investigated. Prototypes were manufactured using a 130 nm standard complementary metal-oxide semiconductor (CMOS) process and compared with devices presented in recent literature. A DC equivalence with the counterpart involving a single equivalent transistor was observed. Experimental results showed a power consumption of 24.99 mW at 1.2 V supply voltage with a minimum die area of 0.685 × 1.2 mm². The higher aspect ratio devices required a proportionally increased die area and power consumption. Conversely, the input-referred noise showed an opposite trend with a minimum of 176.4 nV_rms over the 0.1 to 10 Hz frequency band for a higher aspect ratio. EGFET as a pH sensor presented further validation of the design with an average voltage sensitivity of 50.3 mV/pH, a maximum current sensitivity of 15.71 mA^1/2/pH, a linearity higher than 99.9%, and the possibility of operating at a lower noise level with a compact design and a low complexity.

EGFET-Based Sensors for Bioanalytical Applications: A Review

Since the 1970s, a great deal of attention has been paid to the development of semiconductor-based biosensors because of the numerous advantages they offer, including high sensitivity, faster response time, miniaturization, and low-cost manufacturing for quick biospecific analysis with reusable features. Commercial biosensors have become highly desirable in the fields of medicine, food, and environmental monitoring as well as military applications, whereas increasing concerns about food safety and health issues have resulted in the introduction of novel legislative standards for these sensors. Numerous devices have been developed for monitoring biological processes such as nucleic acid hybridization, protein–protein interaction, antigen–antibody bonds, and substrate–enzyme reactions, just to name a few. Since the 1980s, scientific interest moved to the development of semiconductor-based devices, which also include integrated front-end electronics, such as the extended-gate field-effect transistor (EGFET) biosensor, one of the first miniaturized chemical sensors. This work is intended to be a review of the state of the art focused on the development of biosensors and chemosensors based on extended-gate field-effect transistor within the field of bioanalytical applications, which will highlight the most recent research reported in the literature. Moreover, a comparison among the diverse EGFET devices will be presented, giving particular attention to the materials and technologies.

Nanocomposite Platform Based on EDTA Modified Ppy/SWNTs for the Sensing of Pb(II) Ions by Electrochemical Method

Heavy metal ions are considered as one of the major water pollutants, revealing health hazards as well as threat to the ecosystem. Therefore, investigation of most versatile materials for the sensitive and selective detection of heavy metal ions is need of the hour. Proposed work emphasizes the synthesis of conducting polymer and carbon nanotube nanocomposite modified with chelating ligand for the detection of heavy metal ions. Carbon nanotubes are having well known features such as tuneable conductivity, low density, good charge transport ability, and current carrying capacity. Conducting polymers are the most reliable materials for sensing applications due to their environmental stability and tuning of conductivity by doping and de-doping. Formation of nanocomposite of these two idealistic materials is advantageous over the individual material, which can help to tackle the individual limitations of these materials and can form versatile materials with ideal chemical and electrical properties. Chelating ligands are the most favorable materials due to their ability of complex formation with metal ions. The present work possesses a sensing platform based on conducting polymer and carbon nanotube nanocomposite, which is stable in various aqueous media and possess good charge transfer ability. Chelating ligands played an important role in the increased selectivity toward metal ions. Moreover, in present investigation Ethylenediaminetetraacetic acid (EDTA) functionalized polypyrrole (Ppy) and single walled carbon nanotubes (SWNTs) nanocomposite was successfully synthesized by electrochemical method on stainless steel electrode (SSE). The electrochemical detection of Pb(II) ions using EDTA-Ppy/SWNTs nanocomposite was done from aqueous media. Cyclic voltammetry technique was utilized for the electrochemical synthesis of Ppy/SWNTs nanocomposite. Ppy/SWNTs nanocomposite was further modified with EDTA using dip coating technique at room temperature. The EDTA-Ppy/SWNTs modified stainless steel electrode (SSE) exhibited good sensitivity and selectivity toward heavy metal ions [Pb(II)]. Detection limit achieved for Pb(II) ions was 0.07 μM.

A thumb-size electrochemical system for portable sensors

A thumb-size and precise electrochemical system is designed for sensors in size and cost sensitive applications.

Real-time wash-free detection of unlabeled PNA-DNA hybridization using discrete FET sensor

We demonstrate an electrochemical sensor for detection of unlabeled single-stranded DNA using peptide nucleic acid (PNA) probes coupled to the field-effect transistor (FET) gate. The label-free detection relies on the intrinsic charge of the DNA backbone. Similar detection schemes have mainly concentrated on sensitivity improvement with an emphasis on new sensor structures. Our approach focuses on using an extended-gate that separates the FET and the sensing electrode yielding a simple and mass fabricable device. We used PNA probes for efficient hybridization in low salt conditions that is required to avoid the counter ion screening. As a result, significant part of the target DNA lies within the screening length of the sensor. With this, we achieved a wash-free detection where  typical gate potential shifts are more than 70 mV with 1 µM target DNA. We routinely obtained a real-time, label- and wash-free specific detection of target DNA in nanomolar concentration with low-cost electronics and the responses were achieved within minutes after introducing targets to the solution. Furthermore, the results suggest that the sensor performance is limited by specificity rather than by sensitivity and using low-cost electronics does not limit the sensor performance in the presented sensor configuration.

Detection principles of biological and chemical FET sensors

The seminal importance of detecting ions and molecules for point-of-care tests has driven the search for more sensitive, specific, and robust sensors. Electronic detection holds promise for future miniaturized in-situ applications and can be integrated into existing electronic manufacturing processes and technology. The resulting small devices will be inherently well suited for multiplexed and parallel detection. In this review, different field-effect transistor (FET) structures and detection principles are discussed, including label-free and indirect detection mechanisms. The fundamental detection principle governing every potentiometric sensor is introduced, and different state-of-the-art FET sensor structures are reviewed. This is followed by an analysis of electrolyte interfaces and their influence on sensor operation. Finally, the fundamentals of different detection mechanisms are reviewed and some detection schemes are discussed. In the conclusion, current commercial efforts are briefly considered.