Comparison of Coatings from Reactive Star Shaped PEG-stat-PPG Prepolymers and Grafted Linear PEG for Biological and Medical Applications

Degradable Plasma-Polymerized Poly(Ethylene Glycol)-Like Coating as a Matrix for Food-Packaging Applications

Currently, there is considerable interest in seeking an environmentally friendly technique that is neither thermally nor organic solvent-dependent for producing advanced polymer films for food-packaging applications. Among different approaches, plasma polymerization is a promising method that can deposit biodegradable coatings on top of polymer films. In this study, an atmospheric-pressure aerosol-assisted plasma deposition method was employed to develop a poly(ethylene glycol) (PEG)-like coating, which can act as a potential matrix for antimicrobial agents, by envisioning controlled-release food-packaging applications. Different plasma operating parameters, including the input power, monomer flow rate, and gap between the edge of the plasma head and substrate, were optimized to produce a PEG-like coating with a desirable water stability level and that can be biodegradable. The findings revealed that increased distance between the plasma head and substrate intensified gas-phase nucleation and diluted the active plasma species, which in turn led to the formation of a non-conformal rough coating. Conversely, at short plasma-substrate distances, smooth conformal coatings were obtained. Furthermore, at low input powers (<250 W), the chemical structure of the precursor was mostly preserved with a high retention of C-O functional groups due to limited monomer fragmentation. At the same time, these coatings exhibit low stability in water, which could be attributed to their low cross-linking degree. Increasing the power to 350 W resulted in the loss of the PEG-like chemical structure, which is due to the enhanced monomer fragmentation at high power. Nevertheless, owing to the enhanced cross-linking degree, these coatings were more stable in water. Finally, it could be concluded that a moderate input power (250-300 W) should be applied to obtain an acceptable tradeoff between the coating stability and PEG resemblance.

Unraveling the Mechanism and Kinetics of Binding of an LCI-eGFP-Polymer for Antifouling Coatings

The ability of proteins to adsorb irreversibly onto surfaces opens new possibilities to functionalize biological interfaces. Herein, the mechanism and kinetics of adsorption of protein-polymer macromolecules with the ability to equip surfaces with antifouling properties are investigated. These macromolecules consist of the liquid chromatography peak I peptide from which antifouling polymer brushes are grafted using single electron transfer-living radical polymerization. Surface plasmon resonance spectroscopy reveals an adsorption mechanism that follows a Langmuir-type of binding with a strong binding affinity to gold. X-ray reflectivity supports this by proving that the binding occurs exclusively by the peptide. However, the lateral organization at the surface is directed by the cylindrical eGFP. The antifouling functionality of the unimolecular coatings is confirmed by contact with blood plasma. All coatings reduce the fouling from blood plasma by 8894% with only minor effect of the degree of polymerization for the studied range (DP between 101 and 932). The excellent antifouling properties, combined with the ease of polymerization and the straightforward coating procedure make this a very promising antifouling concept for a multiplicity of applications.

Inducing Immunomodulatory Effects on Human Macrophages by Multifunctional NCO-sP(EO-stat-PO)/Gelatin Hydrogel Nanofibers

Endowing materials and scaffolds with immunomodulatory properties has evolved into a very active field of research. However, combining such effects with multifunctionality regarding cell adhesion and manipulation is still challenging due to the intricate nature of cell-substrate interactions that require fine-tuning of scaffold properties. Here, we reported electrospinning of a well-known biopolymer, gelatin, together with six-arm star-shaped poly(ethylene oxide-stat-propylene oxide) prepolymer with isocyanate end groups (NCO-sP(EO-stat-PO)) as a reactive prepolymer cross-linker. Covalent coupling of two components during and after processing yielded a network of hydrogel fibers that was remarkably stable under aqueous and also proteolytic conditions without the need for extra cross-linking, with a significant increase in stability with increasing NCO-sP(EO-stat-PO) content. When seeded with human macrophages, cells adhered and spread on the fibers and were found highly viable after 7 days of culture across all scaffolds. Furthermore, hybrid fibrous meshes upregulated the expression of a prohealing gene, CD206, while downregulating proinflammatory genes, IL-1β and IL-8. Markedly, NCO-sP(EO-stat-PO)-rich samples induced a significantly reduced release of proinflammatory cytokines, IL-1β, IL-6, and IL-8. Finally, we successfully conjugated IL-4 to NCO-sP(EO-stat-PO) that effectively steered macrophages into a prohealing M2 type, demonstrating additional and robust control over the immunomodulatory feature of the scaffolds.

Surface modification of polystyrene Petri dishes by plasma polymerized 4,7,10-trioxa-1,13-tridecanediamine for enhanced culturing and migration of bovine aortic endothelial cells

Plasma surface modification is an effective method for changing material properties to control cell behavior on a surface. This study investigates the efficiency of a plasma polymerized 4,7,10-trioxa-1,13-tridecanediamine (ppTTDDA) film coated on a polystyrene (PS) Petri dish, which is a biocompatible surface with carbon- and oxygen-based chemical species. The adhesion, proliferation, and migration properties of bovine aortic endothelial cells (BAECs) were profoundly enhanced in the ppTTDDA-coated PS Petri dishes without extracellular matrix (ECM) proteins, when compared with the uncoated PS Petri dishes. These observations indicate that ppTTDDA-coated PS Petri dishes can directly interact with cells, regardless of cell adhesion molecules. The increased cell affinity was attributed to the high concentration of carboxyl group on the surface of the ppTTDDA film. Such a carboxyl surface showed an excellent ability to promote culturing of BAECs. Plasma surface modification techniques are effective in improving biocompatibility and provide a surface environment for cell culture.

Elucidating Branching Topology and Branch Lengths in Star-Branched Polymers by Tandem Mass Spectrometry

Tandem mass spectrometry (MS²) has been employed to elucidate the topology and branching architecture of star-branched polyethers. The polymers were ionized by matrix-assisted laser desorption/ionization (MALDI) to positive ions and dissociated after leaving the ion source via laser-induced fragmentation. The bond scissions caused under MALDI-MS² conditions occur preferentially near the core-branch joining points due to energetically favorable homolytic and heterolytic bond cleavages near the core and release of steric strain and/or reduction of crowding. This unique fragmentation mode detaches complete arms from the core generating fragment ion series at the expected molecular weight of each branch. The number of fragment ion distributions observed combined with their mass-to-charge ratios permit conclusive determination of the degree of branching and the corresponding branch lengths, as demonstrated for differently branched homo- and mikto-arm polyether stars synthesized via azide-alkyne click chemistry. The results of this study underscore the utility of MS² for the characterization of branching architecture and branch lengths of (co) polymers with two or more linear chains attached to a functionalized central core.

Self-Assembling Protein-Polymer Bioconjugates for Surfaces with Antifouling Features and Low Nonspecific Binding

A new method is demonstrated for preparing antifouling and low nonspecific adsorption surfaces on poorly reactive hydrophobic substrates, without the need for energy-intensive or environmentally aggressive pretreatments. The surface-active protein hydrophobin was covalently modified with a controlled radical polymerization initiator and allowed to self-assemble as a monolayer on hydrophobic surfaces, followed by the preparation of antifouling surfaces by Cu(0)-mediated living radical polymerization of poly(ethylene glycol) methyl ether acrylate (PEGA) performed in situ. By taking advantage of hydrophobins to achieve at the same time the immobilization of protein A, this approach allowed to prepare surfaces for IgG1 binding featuring greatly reduced nonspecific adsorption. The success of the surface modification strategy was investigated by contact angle, XPS, and AFM characterization, while the antifouling performance and the reduction of nonspecific binding were confirmed by QCM-D measurements.

Regulating polymer adsorption on colloid by surface morphology

The study of polymer adsorption on colloidal particles has attracted intensive attention. In this work, we investigated polymer adsorption on substrate colloidal particles with two complementary morphologies, one of which has bulges (raspberry-like) on the surface and the other of which has holes instead (strawberry-like). Compared to the bulges, the holes on the colloidal particles were found to prevent polymer adsorption and this effect was dependent on the relative dimensions of the polymer coil and hole. This surface morphology effect was attributed mainly to the reduced polymer accessibility to the adsorption sites in holes when the hydrodynamic size of the polymer coil is larger than the hole, due to the size limiting effect. When the hydrodynamic size of the polymer coil is smaller than that of the holes, no difference in polymer adsorption was observed between raspberry-like and strawberry-like colloids. This study provides a strategy for regulating polymer adsorption on colloidal particles by adjusting the fine structures on the surface, which may be advantageous when limited chemical compositions are allowed. For example, protein adsorption on colloidal drugs may be found to be significantly reduced when colloids with surface holes are used.

Role of membrane pore polymerization conditions for pH responsive behavior, catalytic metal nanoparticle synthesis, and PCB degradation

This article describes the effects of changing monomer and cross-linker concentrations on the mass gain, water permeability, Pd-Fe nanoparticle (NP) loading, and the rate of degradation of 3,3',4,4',5-pentachlorobiphenyl (PCB 126) of pore functionalized polyvinylidene fluoride (PVDF) membranes. In this study, monomer (acrylic acid (AA)) and cross-linker (N, N'- methylene-bis (acrylamide)) concentrations were varied from 10 to 20 wt% of polymer solution and 0.5-2 mol% of monomer concentration, respectively. Results showed that responsive behavior of membrane could be tuned in terms of water permeability over a range of 270-1 L m-2 h-1 bar-1, which is a function of water pH. The NP size on the membrane surface was found in the range of 16-23 nm. With increasing cross-linker density the percentage of smaller NPs (< 10 nm) increases due to smaller mesh size formation during in-situ polymerization of membrane. NP loading was found to vary from 0.21 to 0.94 mg per cm2 of membrane area depending on the variation of available carboxyl groups in membrane pore domain. The NPs functionalized membranes were then tested for use as a platform for the degradation of PCB 126. The observed batch reaction rate (Kobs) for PCB 126 degradation for per mg of catalyst loading was found 0.08-0.1 h-1. Degradation study in convective flow mode shows 98.6% PCB 126 is degraded at a residence time of 46.2 s. The corresponding surface area normalized reaction rate (K sa ) is found about two times higher than K sa of batch degradation; suggesting elimination of the effect of diffusion resistance for degradation of PCB 126 in convective flow mode operation. These Pd-Fe-PAA-PVDF membranes and nanoparticles are characterized by TGA, contact angle measurement, surface zeta potential, XRD, SEM, XPS, FIB, TEM and other techniques reveal the details about the membrane surface, pores and nanoparticles size, shape and size-distribution. Statistical analysis based on experimental results allows us to depict responsive behavior of functionalized membrane. In our best knowledge this paper first time reports detail study on responsive behavior of pore functionalized membrane in terms of permeability, NPs size, metal loading and its effect on PCB 126 degradation in a quantified approach.

Novel Surface Coatings Modulating Eukaryotic Cell Adhesion and Preventing Implant Infection

Poor osseointegration and bacterial infection are major causes of orthopedic implant failure. Both problems arise from passive unspecific protein coating that may not optimally support adhesion of osteoblastic cells and which enable bacterial adhesion that subsequently results in biofilm formation. This review addresses emerging concepts of preventing unspecific protein adsorption and biofilm formation by organic coating systems. We especially focus on recent concepts that additionally allow functionalization for preferential cell adhesion using cell adhesion mediating small peptide sequences that do not induce bacterial adherence. One promising approach that is presented and discussed within this context is the use of NCO-sP(EO-stat-PO).

Peptide-functionalized starPEG/heparin hydrogels direct mitogenicity, cell morphology and cartilage matrix distribution in vitro and in vivo

Cell-based tissue engineering is a promising approach for treating cartilage lesions, but available strategies still provide a distinct composition of the extracellular matrix and an inferior mechanical property compared to native cartilage. To achieve fully functional tissue replacement more rationally designed biomaterials may be needed, introducing bioactive molecules which modulate cell behavior and guide tissue regeneration. This study aimed at exploring the impact of cell-instructive, adhesion-binding (GCWGGRGDSP called RGD) and collagen-binding (CKLER/CWYRGRL) peptides, incorporated in a tunable, matrixmetalloprotease (MMP)-responsive multi-arm poly(ethylene glycol) (starPEG)/heparin hydrogel on cartilage regeneration parameters in vitro and in vivo. MMP-responsive-starPEG-conjugates with cysteine termini and heparin-maleimide, optionally pre-functionalized with RGD, CKLER, CWYRGRL or control peptides, were cross-linked by Michael type addition to embed and grow mesenchymal stromal cells (MSC) or chondrocytes. While starPEG/heparin-hydrogel strongly supported chondrogenesis of MSC according to COL2A1, BGN and ACAN induction, MMP-degradability enhanced cell viability and proliferation. RGD-modification of the gels promoted cell spreading with intense cell network formation without negative effects on chondrogenesis. However, CKLER and CWYRGRL were unable to enhance the collagen content of constructs. RGD-modification allowed more even collagen type II distribution by chondrocytes throughout the MMP-responsive constructs, especially in vivo. Collectively, peptide-instruction via heparin-enriched MMP-degradable starPEG allowed adjustment of self-renewal, cell morphology and cartilage matrix distribution in order to guide MSC and chondrocyte-based cartilage regeneration towards an improved outcome. Copyright © 2017 John Wiley & Sons, Ltd.

Pore Functionalized PVDF Membranes with In-Situ Synthesized Metal Nanoparticles: Material Characterization, and Toxic Organic Degradation

Functionalized PVDF membrane platforms were developed for environmentally benign in-situ nanostructured Fe/Pd synthesis and remediation of chlorinated organic compounds. To prevent leaching and aggregation, nanoparticle catalysts were integrated into membrane domains functionalized with poly (acrylic acid). Nanoparticles of 16-19 nm were observed inside the membrane pores by using focused ion beam (FIB). This technique prevents mechanical deformation of the membrane, compared to the normal SEM preparation methods, thus providing a clean, smooth surface for nanoparticles characterization. This allowed quantification of nanoparticle properties (size and distribution) versus depth underneath the membrane surface (0-20 µm). The results showed that nanoparticles were uniformly sized and evenly distributed inside the membrane pores. However, the size of nanoparticles inside the membrane pores was 13.9% smaller than those nanoparticles located on the membrane surface. Investigating nanoparticles inside membrane pores increases the accuracy of kinetic analysis and modeling aspects. Furthermore, the Fe/Pd immobilized membranes showed excellent performance in the degradation of chlorinated organics: Over 96% degradation of 3,3',4,4',5-pentachlorobiphenyl (PCB 126) was achieved in less than 15 s residence time in convective flow mode. The regeneration and reuse of this catalytic membrane system were also studied. Particles were examined in XRD upon formation, after deliberate oxidation, and after regeneration. The regenerated sample showed the same crystalline pattern as the original sample. Repeated degradation experiments demonstrated successful PCB 126 dechlorination with nanoparticles regenerated for four cycles with only a small loss in reactivity. It demonstrated that Fe/Pd immobilized membranes have the potential for large-scale remediation applications.

Glycan-Functionalized Microgels for Scavenging and Specific Binding of Lectins

Lectins are proteins with a well-defined carbohydrate recognition domain. Many microbial proteins such as bacterial toxins possess lectin or lectin-like binding domains to interact with cell membranes that are decorated with glycan recognition motifs. We report a straightforward way to prepare monodisperse and biocompatible polyethylene glycol microgels, which carry glycan motifs for specific binding to lectins. The sugar-functionalized colloids exhibit a wide mesh size and a highly accessible volume. The microgels are prepared via drop-based microfluidics combined with radical polymerization. GSII and ECL are used as model lectins that bind specifically to the corresponding carbohydrates, namely, GlcNAc and LacNAc. LacNAc microgels bind ECL with a high capacity and high affinity (K_d ≈ 0.5 to 1 μM), suggesting multivalent binding of the lectin to the LacNAc-decorated flexible microgel network. Glycan-functionalized microgels present a useful tool for lectin scavenging in biomedical applications.

Comparison of RAFT derived Poly(vinylpyrolidone) verses Poly(oligoethyleneglycol methacrylate) for the Stabilization of Glycosylated Gold Nanoparticles

Carbohydrates dictate many biological processes including infection by pathogens. Glycosylated polymers and nanomaterials which have increased affinity due to the cluster glycoside effect, are therefore useful tools to probe function, but also as prophylactic therapies or diagnostic tools. Here, the effect of polymer structure on the coating of gold nanoparticles is studied in the context of grafting density, buffer stability and in a lectin binding assay. RAFT polymerization is used to generate poly(oligoethyleneglycol methacrylates) and poly(N-vinyl pyrolidones) with a thiol end-group for subsequent immobilization onto the gold. It is observed that poly(oligoethylene glycol methacrylates), despite being widely used particle coatings, lead to low grafting densities which in turn resulted in lower stability in biological buffers. A depression of the cloud point upon nanoparticle immobilization is also seen, which might compromise performance. In comparison poly(vinyl pyrolidones) resulted in stable particles with higher grafting densities due to the compact size of each monomer unit. The higher grafting density also enabled an increase in the number of carbohydrates which can be installed per nanoparticle at the chain ends, and gave increased binding in a lectin recognition assay. These results will guide the development of new nanoparticle biosensors with enhanced specificity, affinity and stability.

Basement Membrane Mimics of Biofunctionalized Nanofibers for a Bipolar-Cultured Human Primary Alveolar-Capillary Barrier Model

In vitro reconstruction of an alveolar barrier for modeling normal lung functions and pathological events serve as reproducible, high-throughput pharmaceutical platforms for drug discovery, diagnosis, and regenerative medicine. Despite much effort, the reconstruction of organ-level alveolar barrier functions has failed due to the lack of structural similarity to the natural basement membrane, functionalization with specific ligands for alveolar cell function, the use of primary cells and biodegradability. Here we report a bipolar cultured alveolar-capillary barrier model of human primary cells supported by a basement membrane mimics of fully synthetic bifunctional nanofibers. One-step electrospinning process using a bioresorbable polyester and multifunctional star-shaped polyethylene glycols (sPEG) enables the fabrication of an ultrathin nanofiber mesh with interconnected pores. The nanofiber mesh possessed mechanical stability against cyclic expansion as seen in the lung in vivo. The sPEGs as an additive provide biofunctionality to fibers through the conjugation of peptide to the nanofibers and hydrophilization to prevent unspecific protein adsorption. Biofunctionalized nanofiber meshes facilitated bipolar cultivation of endothelial and epithelial cells with fundamental alveolar functionality and showed higher permeability for molecules compared to microporous films. This nanofiber mesh for a bipolar cultured barrier have the potential to promote growth of an organ-level barrier model for modeling pathological conditions and evaluating drug efficacy, environmental pollutants, and nanotoxicology.

Targeting In-Stent-Stenosis with RGD- and CXCL1-Coated Mini-Stents in Mice

Atherosclerotic lesions that critically narrow the artery can necessitate an angioplasty and stent implantation. Long-term therapeutic effects, however, are limited by excessive arterial remodeling. We here employed a miniaturized nitinol-stent coated with star-shaped polyethylenglycole (star-PEG), and evaluated its bio-functionalization with RGD and CXCL1 for improving in-stent stenosis after implantation into carotid arteries of mice. Nitinol foils or stents (bare metal) were coated with star-PEG, and bio-functionalized with RGD, or RGD/CXCL1. Cell adhesion to star-PEG-coated nitinol foils was unaltered or reduced, whereas bio-functionalization with RGD but foremost RGD/CXCL1 increased adhesion of early angiogenic outgrowth cells (EOCs) and endothelial cells but not smooth muscle cells when compared with bare metal foils. Stimulation of cells with RGD/CXCL1 furthermore increased the proliferation of EOCs. In vivo, bio-functionalization with RGD/CXCL1 significantly reduced neointima formation and thrombus formation, and increased re-endothelialization in apoE-/- carotid arteries compared with bare-metal nitinol stents, star-PEG-coated stents, and stents bio-functionalized with RGD only. Bio-functionalization of star-PEG-coated nitinol-stents with RGD/CXCL1 reduced in-stent neointima formation. By supporting the adhesion and proliferation of endothelial progenitor cells, RGD/CXCL1 coating of stents may help to accelerate endothelial repair after stent implantation, and thus may harbor the potential to limit the complication of in-stent restenosis in clinical approaches.

Atmospheric Solid Analysis Probe-Ion Mobility Mass Spectrometry: An Original Approach to Characterize Grafting on Cyclic Olefin Copolymer Surfaces

A cyclic olefin copolymer (COC) was grafted with aryl layers from aryldiazonium salts, and then we combined infrared spectrometry, atomic force microscopy (AFM), and ion mobility mass spectrometry with atmospheric solid analysis probe ionization (ASAP-IM-MS) to characterize the aryl layers. ASAP is a recent atmospheric ionization method dedicated to the direct analysis of solid samples. We demonstrated that ASAP-IM-MS is complementary to other techniques for characterizing bromine and sulfur derivatives of COC on surfaces. ASAP-IM-MS was useful for optimizing experimental grafting conditions and to elucidate hypotheses around aryl layer formation during the grafting process. Thus, ASAP-IM-MS is a good candidate tool to characterize covalent grafting on COC surfaces.

Combining the incompatible: Block copolymers consecutively displaying activated esters and amines and their use as protein-repellent surface modifiers with multivalent biorecognition

We present the facile synthesis and orthogonal functionalization of diblock copolymers consisting of two incompatible segments, i.e. primary amines and activated esters, and demonstrate their use as protein-repellent brush layers with multivalent biorecognition.

Star-shaped poly(2-methyl-2-oxazoline)-based films: rapid preparation and effects of polymer architecture on antifouling properties

Star-shaped poly(2-methyl-2-oxazoline)-based films prepared through polydopamine-assistance provided enhanced antifouling properties than the linear ones, and showed superior stability than PEG films.

Guidance of mesenchymal stem cells on fibronectin structured hydrogel films

Designing of implant surfaces using a suitable ligand for cell adhesion to stimulate specific biological responses of stem cells will boost the application of regenerative implants. For example, materials that facilitate rapid and guided migration of stem cells would promote tissue regeneration. When seeded on fibronectin (FN) that was homogeneously immmobilized to NCO-sP(EO-stat-PO), which otherwise prevents protein binding and cell adhesion, human mesenchymal stem cells (MSC) revealed a faster migration, increased spreading and a more rapid organization of different cellular components for cell adhesion on fibronectin than on a glass surface. To further explore, how a structural organization of FN controls the behavior of MSC, adhesive lines of FN with varying width between 10 µm and 80 µm and spacings between 5 µm and 20 µm that did not allow cell adhesion were generated. In dependance on both line width and gaps, cells formed adjacent cell contacts, were individually organized in lines, or bridged the lines. With decreasing sizes of FN lines, speed and directionality of cell migration increased, which correlated with organization of the actin cytoskeleton, size and shape of the nuclei as well as of focal adhesions. Together, defined FN lines and gaps enabled a fine tuning of the structural organization of cellular components and migration. Microstructured adhesive substrates can mimic the extracellular matrix in vivo and stimulate cellular mechanisms which play a role in tissue regeneration.

Nanoscaled surface patterns influence adhesion and growth of human dermal fibroblasts

In general, there is a need for passivation of nanopatterned biomaterial surfaces if cells are intended to interact only with a feature of interest. For this reason self-assembled monolayers (SAM), varying in chain length, are used; they are highly effective in preventing protein adsorption or cell adhesion. In addition, a simple and cost-effective technique to design nanopatterns of various sizes and distances, the so-called nanosphere lithography (NSL), is discussed, which allows the control of cell adhesion and growth depending on the feature dimensions. Combining both techniques results in highly selective nanostructured surfaces, showing that single proteins selectively adsorb on activated nanopatterns. Additionally, adhesion and growth of normal human dermal fibroblasts (NHDF) is strongly affected by the nanostructure dimensions, and it is proven that fibronectin (FN) matrix formation of these cells is influenced, too. Moreover, the FN fibrils are linked to the hexagonally close-packed nanopatterns. As a result, the system presented here can be applied in tissue engineering and implant design due to the fact that the nanopattern dimensions give rise to further modifications and allow the introduction of chemical heterogeneity to guide stem cell differentiation in the future.

Long-lasting antifouling coating from multi-armed polymer

We describe a new antifouling surface coating, based on aggregation of a short amphiphilic four-armed PEG-dopamine polymer into particles and on surface binding by catechol chemistry. An unbroken and smooth polymeric coating layer with an average thickness of approximately 4 μm was formed on top of titanium oxide surfaces by a single step reaction. Coatings conferred excellent resistance to protein adhesion. Cell attachment was completely prevented for at least eight weeks, although the membranes themselves did not appear to be intrinsically cytotoxic. When linear PEG or four-armed PEG of higher molecular weight were used, the resulting coatings were inferior in thickness and in preventing protein adhesion. This coating method has potential applicability for biomedical devices susceptible to fouling after implantation.

Dexamethasone released from cochlear implant coatings combined with a protein repellent hydrogel layer inhibits fibroblast proliferation

The insertion of cochlear implants into the inner ear often causes inflammation and fibrosis inside the scala tympani and thus growth of fibrous tissue on the implant surface. This deposition leads to the loss of function in both electrical and laser-based implants. The design of this study was to realize fibroblast growth inhibition by dexamethasone (Dex) released from the base material of the implant [polydimethylsiloxane (PDMS)]. To prevent cell and protein adhesion, the PDMS was coated with a hydrogel layer [star-shaped polyethylene glycol prepolymer (sPEG)]. Drug release rates were studied over 3 months, and surface characterization was performed. It was observed that the hydrogel slightly smoothened the surface roughened by the Dex crystals. The hydrogel coating reduced and prolonged the release of the drug over several months. Unmodified, sPEG-coated, Dex-loaded, and Dex/sPEG-equipped PDMS filaments were cocultivated in vitro with fluorescent fibroblasts, analyzed by fluorescent microscopy, and quantified by cell counting. Compared to the unmodified PDMS, cell growth on all modified filaments was averagely 95% ±standard deviation (SD) less, while cell growth on the bottom of the culture dishes containing Dex-loaded filaments was reduced by 70% ±SD. Both, Dex and sPEG prevented direct cell growth on the filament surfaces, while drug delivery was maintained for the duration of several months.

Ultralow protein adsorbing coatings from clickable PEG nanogel solutions: benefits of attachment under salt-induced phase separation conditions and comparison with PEG/albumin nanogel coatings

Clickable nanogel solutions were synthesized by using the copper catalyzed azide/alkyne cycloaddition (CuAAC) to partially polymerize solutions of azide and alkyne functionalized poly(ethylene glycol) (PEG) monomers. Coatings were fabricated using a second click reaction: a UV thiol-yne attachment of the nanogel solutions to mercaptosilanated glass. Because the CuAAC reaction was effectively halted by the addition of a copper-chelator, we were able to prevent bulk gelation and limit the coating thickness to a single monolayer of nanogels in the absence of the solution reaction. This enabled the inclusion of kosmotropic salts, which caused the PEG to phase-separate and nearly double the nanogel packing density, as confirmed by quartz crystal microbalance with dissipation (QCM-D). Protein adsorption was analyzed by single molecule counting with total internal reflection fluorescence (TIRF) microscopy and cell adhesion assays. Coatings formed from the phase-separated clickable nanogel solutions attached with salt adsorbed significantly less fibrinogen than other 100% PEG coatings tested, as well as poly(L-lysine)-g-PEG (PLL-g-PEG) coatings. However, PEG/albumin nanogel coatings still outperformed the best 100% PEG clickable nanogel coatings. Additional surface cross-linking of the clickable nanogel coating in the presence of copper further reduced levels of fibrinogen adsorption closer to those of PEG/albumin nanogel coatings. However, this step negatively impacted long-term resistance to cell adhesion and dramatically altered the morphology of the coating by atomic force microscopy (AFM). The main benefit of the click strategy is that the partially polymerized solutions are stable almost indefinitely, allowing attachment in the phase-separated state without danger of bulk gelation, and thus producing the best performing 100% PEG coating that we have studied to date.

Arraying cell cultures using PEG-DMA micromolding in standard culture dishes

A robust and effortless procedure is presented, which allows for the microstructuring of standard cell culture dishes. Cell adhesion and proliferation are controlled by three-dimensional poly(ethylene glycol)-dimethacrylate (PEG-DMA) microstructures. The spacing between microwells can be extended to millimeter size in order to enable the combination with robotic workstations. Cell arrays of microcolonies can be studied under boundary-free growth conditions by lift-off of the PEG-DMA layer in which the growth rate is accessible via the evolution of patch areas. Alternatively, PEG-DMA stencils can be used as templates for plasma-induced patterning.

Impact of polymer shell on the formation and time evolution of nanoparticle-protein corona

The study of protein corona formation on nanoparticles (NPs) represents an actual main issue in colloidal, biomedical and toxicological sciences. However, little is known about the influence of polymer shells on the formation and time evolution of protein corona onto functionalized NPs. Therefore, silica-poly(ethylene glycol) core-shell nanohybrids (SNPs@PEG) with different polymer molecular weights (MW) were synthesized and exhaustively characterized. Bovine serum albumin (BSA) at different concentrations (0.1-6 wt%) was used as model protein to study protein corona formation and time evolution. For pristine SNPs and SNPs@PEG (MW=350 g/mol), zeta potential at different incubation times show a dynamical evolution of the nanoparticle-protein corona. Oppositely, for SNPs@PEG with MW≥2000 g/mol a significant suppression of corona formation and time evolution was observed. Furthermore, AFM investigations suggest a different orientation (side-chain or perpendicular) and penetration depth of BSA toward PEGylated surfaces depending on the polymer length which may explain differences in protein corona evolution.

Two dimensional nanoarrays of individual protein molecules

Protein molecules on solid surfaces are essential to a number of applications, such as biosensors, biomaterials, and drug delivery. In most approaches for protein immobilization, inter-molecular distances on the solid surface are not controlled and this may lead to aggregation and crowding. Here, a simple approach to immobilize individual protein molecules in a well-ordered 2D array is shown, using nanopatterns obtained from a polystyrene-block-poly(2-hydroxyethyl methacrylate) (PS-b-PHEMA) diblock copolymer thin film. This water-stable and protein-resistant polymer film contains hexagonally ordered PS cylindrical domains in a PHEMA matrix. The PS domains are activated by incorporating alkyne-functionalized PS and immobilizing azide-tagged proteins specifically onto each PS domain using "Click" chemistry. The nanometer size of the PS domain dictates that each domain can accommodate no more than one protein molecule, as verified by atomic force microscopy imaging. Immunoassay shows that the amount of specifically bound antibody scales with the number density of individual protein molecules on the 2D nanoarrays.

Enhancement of surface graft density of MPEG on alginate/chitosan hydrogel microcapsules for protein repellency

Alginate/chitosan/alginate (ACA) hydrogel microcapsules were modified with methoxy poly(ethylene glycol) (MPEG) to improve protein repellency and biocompatibility. Increased MPEG surface graft density (n(S)) on hydrogel microcapsules was achieved by controlling the grafting parameters including the buffer layer substrate, membrane thickness, and grafting method. X-ray photoelectron spectroscopy (XPS) model was employed to quantitatively analyze n(S) on this three-dimensional (3D) hydrogel network structure. Our results indicated that neutralizing with alginate, increasing membrane thickness, and in situ covalent grafting could increase n(S) effectively. ACAC(PEG) was more promising than ACC(PEG) in protein repellency because alginate supplied more -COO(-) negative binding sites and prevented MPEG from diffusing. The n(S) increased with membrane thickness, showing better protein repellency. Moreover, the in situ covalent grafting provided an effective way to enhance n(S), and 1.00 ± 0.03 chains/nm(2) was achieved, exhibiting almost complete immunity to protein adsorption. This antifouling hydrogel biomaterial is expected to be useful in transplantation in vivo.

Synthesis of cross-linked carboxyl poly(glycerol methacrylate) and its application for the controlled release of doxorubicin

A series of polymers were synthesized by cross-linking carboxyl poly(glycerol methacrylate) (PGOHMA) using hexamethylene diisocyanate (HDI). The structures and molecular weight were characterized by ¹H NMR and gel permeation chromatography (GPC). Nanoparticles were then fabricated for encapsulation of doxorubicin hydrochloride (DOX). The encapsulation and release were affected by the chemical structure and degree of cross-linking of the polymers. The polymers were quite effective in the encapsulation of DOX, and exhibited pH-dependent drug release. Specifically, the stability of nanoparticles in neutral pH was significant enhanced and the release rate was enhanced at acidic pH after cross-linking, which could be potential useful as a controlled drug release carrier, especially for anti-cancer drug.

Blood cell and plasma protein repellent properties of Star-PEG-modified surfaces

The implantation of biomaterials, medical devices or prostheses can instigate a rejection response or initiate an undesirable adsorption of plasma proteins, as well as blood cells on the implant surface, thus triggering diverse defense mechanisms against the supposed pathologic invader. The extent of this inflammatory reaction depends in part on the biocompatibility of the used materials or coatings. Although adsorption and coagulation responses can appear during the total in vivo lifetime of the implant, they are initially and crucially formed within the first 2-4 weeks of implantation. This early phase is of decisive importance for the consecutive in-growth and healing process. The present study was intended to elucidate the effects of blood contact to surfaces modified with reactive six-arm star-shaped poly(ethylene glycol-stat-propylene glycol) pre-polymers (Star PEG). Taken together, for Star-PEG-covered substrates we could demonstrate a profound reduction of various blood-biomaterial interactions compared to non-coated substrates, indicating the promising potential of this material as future coating for biomaterials with blood contact.

Surface-modified silicone foils for intraocular implantation

BACKGROUND

Implantation of silicone materials like iris diaphragms into the eye can be complicated by cell migration and attachment. We studied polydimethylsiloxane (PDMS) foils coated with isocyanate terminated, star-shaped poly(ethylene glycol-stat-propylene glycol) (NCO-sP(EO-stat-PO)) equipped with heparin towards the inhibition of cell attachment without influencing cell viability.

METHODS

Mouse fibroblasts L929 were cultured and seeded onto sterilized pieces of either uncoated NCO-sP(EO-stat-PO) or heparin-NCO-sP(EO-stat-PO) loaded foils. Polyvinylchloride (PVC) foils served as the positive control and biomembranes as the negative control. The cultured cells were examined after 24 h for cell viability and adhesion by fluorescence microscopy; morphological cell changes were documented after hemalaun staining. Cell density was measured and quantification of cell proliferation was assessed by a BrdU test; quantification of cell activity was analyzed by a WST-1 test.

RESULTS

The fibroblasts' cell viability was excellent on all tested foils except the toxic PVC foil. NCO-sP(EO-stat-PO) coating provided significantly reduced cell activity. On heparin-loaded coatings, cells were viable and less dense but showed almost the same cell proliferation and cell activity as on the negative control. NCO-sP(EO-stat-PO) coated, heparin loaded foils proved high biocompatibility and reduced cell adhesion.

CONCLUSIONS

Both NCO-sP(EO-stat-PO)-coated foils with and without heparin seemed to be a viable implantation material for less cell migration, attachment, and reduced implant complications. Conclusive we give a recommendation for further studies on the intraocular implantation in particular for the NCO-sP(EO-stat-PO)-coated foils.

Protein repellent hydrophilic grafts prepared by surface-initiated atom transfer radical polymerization from polypropylene

Cross-linked hydrophilic poly(PEGMA) grafts (red) on PP repel fluorescence labelled insulin (green) when the PP plate is pulled out of the protein solution.