1
|
Ordered porous Mn - Co spinel oxide (CoMn 2O 4) with vacancies modulation as efficient electrocatalyst for Li - O 2 battery. J Colloid Interface Sci 2024; 670:719-728. [PMID: 38788439 DOI: 10.1016/j.jcis.2024.05.144] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/23/2024] [Revised: 05/12/2024] [Accepted: 05/19/2024] [Indexed: 05/26/2024]
Abstract
Nonaqueous Li - O2 battery (LOB) is considered one of the most promising energy storage system due to its ultrahigh theoretical specific capacity (3500 Wh kg-1). Introducing vacancies in CoMn2O4 catalysts is regarded as an effective strategy to enhance the electrochemical performances of LOB. However, the relation between vacancy types in CoMn2O4 and catalytic performances in the LOB remains ambiguous. Herein, ordered porous CoMn2O4 with oxygen and metal vacancies is obtained via solvothermal reaction followed by temperature-controlled calcination using polystyrene spheres as templates. The increase in treatment temperature reduces the content of oxygen vacancies while increasing that of the metal vacancies. Notably, experimental results and theoretical calculations show that oxygen vacancies in CoMn2O4 have a greater influence than metal vacancies in modulating the LiO2 adsorption during the reaction processes and reducing the overpotential. CoMn2O4 synthesized at 500 ℃ (CoMnO-500) with higher oxygen vacancies exhibits stronger adsorption onto the LiO2, facilitating the formation of film-like Li2O2. Therefore, an LOB with the CoMnO-500 catalyst presents the lowest overpotential of 1.2 V and longest cycle lifespan of 286 cycles at a current density of 200 mA g-1. This study offers insights into the effect of CoMn2O4 vacancies on the formation pathway of Li2O2 discharge products.
Collapse
|
2
|
Metallization of Targeted Protein Assemblies in Cell-Derived Extracellular Matrix by Antibody-Guided Biotemplating. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2023; 10:e2302830. [PMID: 37852942 PMCID: PMC10724409 DOI: 10.1002/advs.202302830] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/04/2023] [Revised: 08/30/2023] [Indexed: 10/20/2023]
Abstract
Biological systems are composed of hierarchical structures made of a large number of proteins. These structures are highly sophisticated and challenging to replicate using artificial synthesis methods. To exploit these structures in materials science, biotemplating is used to achieve biocomposites that accurately mimic biological structures and impart functionality of inorganic materials, including electrical conductivity. However, the biological scaffolds used in previous studies are limited to stereotypical and simple morphologies with little synthetic diversity because of a lack of control over their morphologies. This study proposes that the specific protein assemblies within the cell-derived extracellular matrix (ECM), whose morphological features are widely tailorable, can be employed as versatile biotemplates. In a typical procedure, a fibrillar assembly of fibronectin-a constituent protein of the ECM-is metalized through an antibody-guided biotemplating approach. Specifically, the antibody-bearing nanogold is attached to the fibronectin through antibody-antigen interactions, and then metals are grown on the nanogold acting as a seed. The biomimetic structure can be adapted for hydrogen production and sensing after improving its electrical conductivity through thermal sintering or additional metal growth. This study demonstrates that cell-derived ECM can be an attractive option for addressing the diversity limitation of a conventional biotemplate.
Collapse
|
3
|
Recent advances and progress in biotemplate catalysts for electrochemical energy storage and conversion. Adv Colloid Interface Sci 2023; 318:102958. [PMID: 37453344 DOI: 10.1016/j.cis.2023.102958] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/28/2023] [Revised: 06/05/2023] [Accepted: 06/30/2023] [Indexed: 07/18/2023]
Abstract
Complex structures and morphologies in nature endow materials with unexpected properties and extraordinary functions. Biotemplating is an emerging strategy for replicating nature structures to obtain materials with unique morphologies and improved properties. Recently, efforts have been made to use bio-inspired species as a template for producing morphology-controllable catalysts. Fundamental information, along with recent advances in biotemplate metal-based catalysts are presented in this review through discussions of various structures and biotemplates employed for catalyst preparation. This review also outlines the recent progress on preparation routes of biotemplate catalysts and discusses how the properties and structures of these templates play a crucial role in the final performance of metal-based catalysts. Additionally, the application of bio-based metal and metal oxide catalysts is highlighted for various key energy and environmental technologies, including photocatalysis, fuel cells, and lithium batteries. Biotemplate metal-based catalysts display high efficiency in several energy and environmental systems. Note that this review provides guidance for further research in this direction.
Collapse
|
4
|
Diffusion and molecular partitioning in hierarchically complex virus-like particles. Virology 2023; 580:50-60. [PMID: 36764014 DOI: 10.1016/j.virol.2023.01.012] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/11/2022] [Revised: 01/09/2023] [Accepted: 01/12/2023] [Indexed: 01/22/2023]
Abstract
Viruses are diverse infectious agents found in virtually every type of natural environment. Due to the range of conditions in which viruses have evolved, they exhibit a wide range of structure and function which has been exploited for biotechnology. The self-assembly process of virus-like particles (VLPs), derived from structural virus components, allows for the assembly of a hierarchy of materials. Because VLPs are robust in both their assembly and the final product, functionality can be incorporated through design of their building blocks or chemical modification after their synthesis and assembly. In particular, encapsulation of active enzymes inside VLP results in macromolecular concentration approximating that of cells, introducing excluded volume effects on encapsulated cargo which are not present in traditional experiments done on dilute proteins. This work reviews the hierarchical assembly of VLPs, experiments investigating diffusion in VLP systems, and methods for partitioning of chemical species in VLPs as functional biomaterials.
Collapse
|
5
|
M13 Bacteriophage-Based Bio-nano Systems for Bioapplication. BIOCHIP JOURNAL 2022. [DOI: 10.1007/s13206-022-00069-w] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/02/2022]
|
6
|
Rationalizing the effect of surface electronic structure on oxygen electrocatalyst for high performance lithium-oxygen battery. Electrochim Acta 2022. [DOI: 10.1016/j.electacta.2022.139891] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/11/2022]
|
7
|
Zn‒air battery operated with a 3DOM trimetallic spinel (Mn0.5Ni0.5Co2O4) as the oxygen electrode. Electrochim Acta 2021. [DOI: 10.1016/j.electacta.2021.138900] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
|
8
|
Recent Advances in Fabrication of Well-Organized Protein-Based Nanostructures. ACS APPLIED BIO MATERIALS 2021; 4:4039-4048. [DOI: 10.1021/acsabm.1c00156] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/22/2022]
|
9
|
Recent Advances in Bio-Templated Metallic Nanomaterial Synthesis and Electrocatalytic Applications. CHEMSUSCHEM 2021; 14:758-791. [PMID: 33296559 DOI: 10.1002/cssc.202002532] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/29/2020] [Revised: 12/08/2020] [Indexed: 06/12/2023]
Abstract
Developing metallic nanocatalysts with high reaction activity, selectivity and practical durability is a promising and active subfield in electrocatalysis. In the classical "bottom-up" approach to synthesize stable nanomaterials by chemical reduction, stabilizing additives such as polymers or organic surfactants must be present to cap the nanoparticle to prevent material bulk aggregation. In recent years, biological systems have emerged as green alternatives to support the uncoated inorganic components. One key advantage of biological templates is their inherent ability to produce nanostructures with controllable composition, facet, size and morphology under ecologically friendly synthetic conditions, which are difficult to achieve with traditional inorganic synthesis. In addition, through genetic engineering or bioconjugation, bio-templates can provide numerous possibilities for surface functionalization to incorporate specific binding sites for the target metals. Therefore, in bio-templated systems, the electrocatalytic performance of the formed nanocatalyst can be tuned by precisely controlling the material surface chemistry. With controlled improvements in size, morphology, facet exposure, surface area and electron conductivity, bio-inspired nanomaterials often exhibit enhanced catalytic activity towards electrode reactions. In this Review, recent research developments are presented in bio-approaches for metallic nanomaterial synthesis and their applications in electrocatalysis for sustainable energy storage and conversion systems.
Collapse
|
10
|
Soft-template-assisted synthesis: a promising approach for the fabrication of transition metal oxides. NANOSCALE ADVANCES 2020; 2:5015-5045. [PMID: 36132034 PMCID: PMC9417152 DOI: 10.1039/d0na00599a] [Citation(s) in RCA: 31] [Impact Index Per Article: 7.8] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/22/2020] [Accepted: 09/18/2020] [Indexed: 05/27/2023]
Abstract
The past few decades have witnessed transition metal oxides (TMOs) as promising candidates for a plethora of applications in numerous fields. The exceptional properties retained by these materials have rendered them of paramount emphasis as functional materials. Thus, the controlled and scalable synthesis of transition metal oxides with desired properties has received enormous attention. Out of different top-down and bottom-up approaches, template-assisted synthesis predominates as an adept approach for the facile synthesis of transition metal oxides, owing to its phenomenal ability for morphological and physicochemical tuning. This review presents a comprehensive examination of the recent advances in the soft-template-assisted synthesis of TMOs, focusing on the morphological and physicochemical tuning aided by different soft-templates. The promising applications of TMOs are explained in detail, emphasizing those with excellent performances.
Collapse
|
11
|
|
12
|
Abstract
A selenium nanoparticle binding peptide was isolated from a phage display library and genetically fused to a metalloid reductase that reduces selenite (SeO32-) to a Se0 nanoparticle (SeNP) form. The fusion of the Se binding peptide to the metalloid reductase regulates the size of the resulting SeNP to ∼35 nm average diameter, where without the peptide, SeNPs grow to micron sized polydisperse precipitates. The SeNP product remains associated with the enzyme/peptide fusion. The Se binding peptide fusion to the enzyme increases the enzyme's SeO32- reductase activity. Size control of particles was diminished if the Se binding peptide was only added exogenously to the reaction mixture. The enzyme-peptide construct shows preference for binding smaller SeNPs. The peptide-SeNP interaction is attributed to His based ligation that results in a peptide conformational change on the basis of Raman spectroscopy.
Collapse
|
13
|
Synthesis of monodisperse rod-shaped silica particles through biotemplating of surface-functionalized bacteria. NANOSCALE 2020; 12:8732-8741. [PMID: 32307501 DOI: 10.1039/d0nr00669f] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/11/2023]
Abstract
Mesoporous silica particles of controlled size and shape are potentially beneficial for many applications, but their usage may be limited by the complex procedure of fabrication. Biotemplating provides a facile approach to synthesize materials with desired shapes. Herein, a bioinspired design principle is adopted through displaying silaffin-derived 5R5 proteins on the surface of Escherichia coli by genetic manipulations. The genetically modified Escherichia coli provides a three-dimensional template to regulate the synthesis of rod-shaped silica. The silicification is initiated on the cell surface under the functionality of 5R5 proteins and subsequentially the inner space is gradually filled. Density functional theory simulation reveals the interfacial interactions between silica precursors and R5 peptides at the atomic scale. There is a large conformation change of this protein during biosilicification. Electrostatic interactions contribute to the high affinity between positively charged residues (Lys4, Arg16, Arg17) and negatively charged tetraethyl orthosilicate. Hydrogen bonds develop between Arg16 (OH), Arg17 (OH and NH), Leu19 (OH) residues and the forming silica agglomerates. In addition, the resulting rod-shaped silica copy of the bacteria can transform into mesoporous SiOx nanorods composed of carbon-coated nanoparticles after carbonization, which is shown to allow superior lithium storage performance.
Collapse
|
14
|
Abstract
Understanding viral assembly pathways is of critical importance to biology, medicine, and nanotechology. Here, we study the assembly path of a system with various structures, the simian vacuolating virus 40 (SV40) polymorphs. We simulate the templated assembly process of VP1 pentamers, which are the constituents of SV40, into icosahedal shells made of N = 12 pentamers (T = 1). The simulations include connections formed between pentamers by C-terminal flexible lateral units, termed here "C-terminal ligands", which are shown to control assembly behavior and shell dynamics. The model also incorporates electrostatic attractions between the N-terminal peptide strands (ligands) and the negatively charged cargo, allowing for agreement with experiments of RNA templated assembly at various pH and ionic conditions. During viral assembly, pentamers bound to any template increase its effective size due to the length and flexibility of the C-terminal ligands, which can connect to other VP1 pentamers and recruit them to a partially completed capsid. All closed shells formed other than the T = 1 feature the ability to dynamically rearrange and are thus termed "pseudo-closed". The N = 13 shell can even spontaneously "self-correct" by losing a pentamer and become a T = 1 capsid when the template size fluctuates. Bound pentamers recruiting additional pentamers to dynamically rearranging capsids allow closed shells to continue growing via the pseudo-closed growth mechanism, for which experimental evidence already exists. Overall, we show that the C-terminal ligands control the dynamic assembly paths of SV40 polymorphs.
Collapse
|
15
|
Nanobiohybrid Material‐Based Bioelectronic Devices. Biotechnol J 2020; 15:e1900347. [DOI: 10.1002/biot.201900347] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/30/2019] [Revised: 02/19/2020] [Indexed: 12/14/2022]
|
16
|
Bacteriophage nanofiber fabrication using near field electrospinning. RSC Adv 2019; 9:39111-39118. [PMID: 35540674 PMCID: PMC9075989 DOI: 10.1039/c9ra07510k] [Citation(s) in RCA: 7] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/17/2019] [Accepted: 11/08/2019] [Indexed: 12/11/2022] Open
Abstract
M13 bacteriophage (phage) nano- and microfibers were fabricated using electrospinning. Using liquid crystalline suspension of the phage, we successfully fabricated nano- and microscale pure phage fibers. Through a near field electrospinning process, we fabricated the desired phage fiber pattern with tunable direction and spacing. In addition, we demonstrated that the resulting phage fibers could be utilized as an electrostatic-stimulus responsive actuator. The near field electrospinning would be a very useful tool to design phage-based chemical sensors, tissue regenerative materials, energy generators, metallic and semiconductor nanowires in the future.
Collapse
|
17
|
Antiperovskite Nitrides CuNCo 3-xV x: Highly Efficient and Durable Electrocatalysts for the Oxygen-Evolution Reaction. NANO LETTERS 2019; 19:7457-7463. [PMID: 31532687 DOI: 10.1021/acs.nanolett.9b03168] [Citation(s) in RCA: 25] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/10/2023]
Abstract
Perovskite oxides have attracted much attention for enabling the oxygen-evolution reaction (OER) over the past decades. Nevertheless, their poor conductivity is still a barrier hindering their use. Herein, we report a catalyst prototype of Co-based antiperovskite nitrides CuNCo3-xVx (0 ≤ x ≤ 1) to be a highly effective OER electrocatalyst. The synthesized CuNCo3-xVx exhibits greatly enhanced activity and stability toward the OER in alkaline medium. The CuNCo2.4V0.6 shows a mere 235 mV of overpotential to reach 10 mA cm-2, which is comparable to that of Ir/C (232 mV). More importantly, the CuNCo2.4V0.6 is more durable than the conventional Ir/C catalyst. The CuNCo2.4V0.6 catalyst enabled a Zn-air battery to exhibit a cycle life of 143 h with a much higher cell efficiency. The V-substituted CuNCo2.4V0.6 provides a higher content of the desirable Co3+ species in the post-OER catalyst, which ensures a high activity over a long-term operation. With these enhanced effects enabled by the compositional flexibility of CuNCo3-xVx antiperovskite nitride, a feasible strategy for optimizing an electrocatalyst with tunable properties is provided.
Collapse
|
18
|
Electric Field Assisted Self-Assembly of Viruses into Colored Thin Films. NANOMATERIALS 2019; 9:nano9091310. [PMID: 31540252 PMCID: PMC6781059 DOI: 10.3390/nano9091310] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 08/07/2019] [Revised: 08/28/2019] [Accepted: 09/10/2019] [Indexed: 02/07/2023]
Abstract
Filamentous viruses called M13 bacteriophages are promising materials for devices with thin film coatings because phages are functionalizable, and they can self-assemble into smectic helicoidal nanofilament structures. However, the existing “pulling” approach to align the nanofilaments is slow and limits potential commercialization of this technology. This study uses an applied electric field to rapidly align the nanostructures in a fixed droplet. The electric field reduces pinning of the three-phase contact line, allowing it to recede at a constant rate. Atomic force microscopy reveals that the resulting aligned structures resemble those produced via the pulling method. The field-assisted alignment results in concentric color bands quantified with image analysis of red, green, and blue line profiles. The alignment technique shown here could reduce self-assembly time from hours to minutes and lend itself to scalable manufacturing techniques such as inkjet printing.
Collapse
|
19
|
Ultrathin Co3O4 Nanosheets with Edge-Enriched {111} Planes as Efficient Catalysts for Lithium–Oxygen Batteries. ACS Catal 2019. [DOI: 10.1021/acscatal.8b05182] [Citation(s) in RCA: 56] [Impact Index Per Article: 11.2] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
|
20
|
Highly adjustable 3D nano-architectures and chemistries via assembled 1D biological templates. NANOSCALE 2019; 11:1091-1102. [PMID: 30574649 DOI: 10.1039/c8nr04864a] [Citation(s) in RCA: 11] [Impact Index Per Article: 2.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/09/2023]
Abstract
Porous metal nanofoams have made significant contributions to a diverse set of technologies from separation and filtration to aerospace. Nonetheless, finer control over nano and microscale features must be gained to reach the full potential of these materials in energy storage, catalytic, and sensing applications. As biologics naturally occur and assemble into nano and micro architectures, templating on assembled biological materials enables nanoscale architectural control without the limited chemical scope or specialized equipment inherent to alternative synthetic techniques. Here, we rationally assemble 1D biological templates into scalable, 3D structures to fabricate metal nanofoams with a variety of genetically programmable architectures and material chemistries. We demonstrate that nanofoam architecture can be modulated by manipulating viral assembly, specifically by editing the viral surface coat protein, as well as altering templating density. These architectures were retained over a broad range of compositions including monometallic and bi-metallic combinations of noble and transition metals of copper, nickel, cobalt, and gold. Phosphorous and boron incorporation was also explored. In addition to increasing the surface area over a factor of 50, as compared to the nanofoam's geometric footprint, this process also resulted in a decreased average crystal size and altered phase composition as compared to non-templated controls. Finally, templated hydrogels were deposited on the centimeter scale into an array of substrates as well as free standing foams, demonstrating the scalability and flexibility of this synthetic method towards device integration. As such, we anticipate that this method will provide a platform to better study the synergistic and de-coupled effects between nano-structure and composition for a variety of applications including energy storage, catalysis, and sensing.
Collapse
|
21
|
Nanoparticle Fabrication on Bacterial Microcompartment Surface for the Development of Hybrid Enzyme-Inorganic Catalyst. ACS Catal 2018. [DOI: 10.1021/acscatal.8b02322] [Citation(s) in RCA: 19] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/27/2022]
|
22
|
Improved structural design of single- and double-wall MnCo 2O 4 nanotube cathodes for long-life Li-O 2 batteries. NANOSCALE 2018; 10:13149-13158. [PMID: 29963679 DOI: 10.1039/c8nr02795a] [Citation(s) in RCA: 8] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/08/2023]
Abstract
Developing a cathode material with a stable pore structure and efficient bifunctional activity toward oxygen electrochemistry is the key to achieve practical and high-performance Li-O2 batteries. Here, hierarchically porous MnCo2O4 nanotubes with single- or double-wall architecture are fabricated through a facile electrospinning technique, by adjusting the concentration of the electrospinning solution. The electrochemical measurements indicate that both types of nanotubes possess excellent catalytic abilities toward oxygen reduction and evolution reactions in alkaline aqueous or non-aqueous media. When used as air-electrode catalysts for Li-O2 batteries, both single- and double-wall MnCo2O4 nanotubes show significantly improved electrochemical performance. In particular, the novel double-wall MnCo2O4 nanotubes (DW-MCO-NT), with a high surface area and a large pore volume almost twice as big as the single-wall nanotubes, can offer numerous catalytically active sites as well as sufficient space to deposit discharge products. The DW-MCO-NT based Li-O2 batteries can deliver a maximum discharge capacity of 8100 mA h g-1, with a potential plateau at 2.77 V, and achieve an excellent cyclability over 278 cycles, under strict conditions of 1000 mA h g-1 at 400 mA g-1 within 2.6-4.3 V. Moreover, the XRD and SEM analyses show that the dominant discharge product with a particulate shape is crystal Li2O2 and is prone to being completely decomposed, endowing the MnCo2O4 nanotube-based Li-O2 battery with a long cycle life.
Collapse
|
23
|
Toward Escherichia coli bacteria machine for water oxidation. PHOTOSYNTHESIS RESEARCH 2018; 136:257-267. [PMID: 29589334 DOI: 10.1007/s11120-018-0499-7] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/01/2018] [Accepted: 03/09/2018] [Indexed: 06/08/2023]
Abstract
Nature uses a Mn oxide-based catalyst for water oxidation in plants, algae, and cyanobacteria. Mn oxides are among major candidates to be used as water-oxidizing catalysts. Herein, we used two straightforward and promising methods to form Escherichia coli bacteria/Mn oxide compounds. In one of the methods, the bacteria template was intact after the reaction. The catalysts were characterized by X-ray photoelectron spectroscopy, visible spectroscopy, scanning electron microscopy, high-resolution transmission electron microscopy, diffuse reflectance infrared Fourier transform spectroscopy, Raman spectroscopy, and X-ray diffraction spectrometry. Electrochemical properties of the catalysts were studied, and attributed redox potentials were assigned. The water oxidation of the compounds was examined under electrochemical condition. Linear sweep voltammetry showed that the onsets of water oxidation in our experimental condition for bacteria and Escherichia coli bacteria/Mn oxide were 1.68 and 1.56 V versus the normal hydrogen electrode (NHE), respectively. Thus, the presence of Mn oxide in the catalyst significantly decreased (~ 120 mV) the overpotential needed for water oxidation.
Collapse
|
24
|
A Review of Carbon-Composited Materials as Air-Electrode Bifunctional Electrocatalysts for Metal–Air Batteries. ELECTROCHEM ENERGY R 2018. [DOI: 10.1007/s41918-018-0002-3] [Citation(s) in RCA: 105] [Impact Index Per Article: 17.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/17/2022]
Abstract
Abstract
Metal–air batteries (MABs), particularly rechargeable MABs, have gained renewed interests as a potential energy storage/conversion solution due to their high specific energy, low cost, and safety. The development of MABs has, however, been considerably hampered by its relatively low rate capability and its lack of efficient and stable air catalysts in which the former stems mainly from the sluggish kinetics of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) and the latter stems from the corrosion/oxidation of carbon materials in the presence of oxygen and high electrode potentials. In this review, various carbon-composited bifunctional electrocatalysts are reviewed to summarize progresses in the enhancement of ORR/OER and durability induced by the synergistic effects between carbon and other component(s). Catalyst mechanisms of the reaction processes and associated performance enhancements as well as technical challenges hindering commercialization are also analyzed. To facilitate further research and development, several research directions for overcoming these challenges are also proposed.
Collapse
|
25
|
|
26
|
Functional and stability orientation synthesis of materials and structures in aprotic Li–O2batteries. Chem Soc Rev 2018; 47:2921-3004. [DOI: 10.1039/c8cs00009c] [Citation(s) in RCA: 224] [Impact Index Per Article: 37.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/23/2022]
Abstract
This review presents the recent advances made in the functional and stability orientation synthesis of materials/structures for Li–O2batteries.
Collapse
|
27
|
Drug delivery vectors based on filamentous bacteriophages and phage-mimetic nanoparticles. Drug Deliv 2017; 24:1898-1908. [PMID: 29191048 PMCID: PMC8241185 DOI: 10.1080/10717544.2017.1410259] [Citation(s) in RCA: 40] [Impact Index Per Article: 5.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/02/2017] [Revised: 11/16/2017] [Accepted: 11/23/2017] [Indexed: 12/11/2022] Open
Abstract
With the development of nanomedicine, a mass of nanocarriers have been exploited and utilized for targeted drug delivery, including liposomes, polymers, nanoparticles, viruses, and stem cells. Due to huge surface bearing capacity and flexible genetic engineering property, filamentous bacteriophage and phage-mimetic nanoparticles are attracting more and more attentions. As a rod-like bio-nanofiber without tropism to mammalian cells, filamentous phage can be easily loaded with drugs and directly delivered to the lesion location. In particular, chemical drugs can be conjugated on phage surface by chemical modification, and gene drugs can also be inserted into the genome of phage by recombinant DNA technology. Meanwhile, specific peptides/proteins displayed on the phage surface are able to conjugate with nanoparticles which will endow them specific-targeting and huge drug-loading capacity. Additionally, phage peptides/proteins can directly self-assemble into phage-mimetic nanoparticles which may be applied for self-navigating drug delivery nanovehicles. In this review, we summarize the production of phage particles, the identification of targeting peptides, and the recent applications of filamentous bacteriophages as well as their protein/peptide for targeting drug delivery in vitro and in vivo. The improvement of our understanding of filamentous bacteriophage and phage-mimetic nanoparticles will supply new tools for biotechnological approaches.
Collapse
|
28
|
Uniform Fe x Ni y Nanospheres: Cost-Effective Electrocatalysts for Nonaqueous Rechargeable Li-O 2 Batteries. ACS OMEGA 2017; 2:4269-4277. [PMID: 31457719 PMCID: PMC6641725 DOI: 10.1021/acsomega.7b00497] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/22/2017] [Accepted: 07/21/2017] [Indexed: 05/15/2023]
Abstract
Uniform Fe x Ni y nanospheres were synthesized via a simple solvothermal method and used as electrocatalysts for Li-O2 batteries. Fe7Ni3 nanospheres exhibited relatively high catalytic activities in the electrochemical tests. They delivered a reversible capacity of more than 7000 mAh/gKB and gave a discharge-charge voltage gap reduction of 250 mV compared with Ketjen Black.
Collapse
|
29
|
Biointerface Structural Effects on the Properties and Applications of Bioinspired Peptide-Based Nanomaterials. Chem Rev 2017; 117:12641-12704. [DOI: 10.1021/acs.chemrev.7b00139] [Citation(s) in RCA: 132] [Impact Index Per Article: 18.9] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/24/2022]
|
30
|
Crab-shell induced synthesis of ordered macroporous carbon nanofiber arrays coupled with MnCo 2O 4 nanoparticles as bifunctional oxygen catalysts for rechargeable Zn-air batteries. NANOSCALE 2017; 9:11148-11157. [PMID: 28749503 DOI: 10.1039/c7nr03009f] [Citation(s) in RCA: 8] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/07/2023]
Abstract
The oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are traditionally carried out using noble metals (such as Pt) and metal oxides (such as RuO2 and IrO2) as catalysts, respectively. Nevertheless, several key issues such as high cost, poor stability, and detrimental environmental effects limit the catalytic activity of these noble metal- and metal oxide-based catalysts. Herein, we have designed and synthesized macroporous carbon nanofiber arrays by using a natural crab shell template. Subsequently, spinel MnCo2O4 nanoparticles were embedded into the nitrogen-doped macroporous carbon nanofiber arrays (NMCNAs) by a hydrothermal method. Accompanied by the good conductivity, large surface area and doping of nitrogen, the as-prepared MnCo2O4/NMCNA exhibited remarkable catalytic performance and outstanding stability for both ORR and OER in alkaline media. The macroporous superstructures play vital role in reducing the ion transport resistance and facilitating the diffusion of gaseous products (O2). Finally, rechargeable Zn-air batteries using the MnCo2O4/NMCNA catalyst displayed appreciably lower overpotentials, higher power density and better stability than commercial Pt/C, thus raising the prospect of functional low-cost, non-precious-metal bifunctional catalysts in metal-air batteries.
Collapse
|
31
|
Protein-templated synthesis of metal-based nanomaterials. Curr Opin Biotechnol 2017; 46:14-19. [DOI: 10.1016/j.copbio.2016.10.015] [Citation(s) in RCA: 22] [Impact Index Per Article: 3.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/11/2016] [Accepted: 10/24/2016] [Indexed: 01/07/2023]
|
32
|
Facile synthesis of ultrathin Ni-MOF nanobelts for high-efficiency determination of glucose in human serum. JOURNAL OF MATERIALS CHEMISTRY. B 2017; 5:5234-5239. [PMID: 32264108 DOI: 10.1039/c7ta02454a] [Citation(s) in RCA: 135] [Impact Index Per Article: 19.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/20/2023]
Abstract
Ultrathin Ni-MOF nanobelts, [Ni20(C5H6O4)20(H2O)8]·40H2O(Ni-MIL-77 NBs), were synthesized by a facile one-pot solution process and can be used as an efficient catalyst electrode for glucose oxidation under alkaline conditions. Electrochemical measurements demonstrate that the NB/GCE, when used as a non-enzymatic glucose sensor, offers superior analytical performances with a wide linear range (from 1 μM to 500 μM), a low detection limit (0.25 μM, signal-to-noise = 3), and a response sensitivity of 1.542 μA mM-1 cm-2. Moreover, it can also be applied for glucose detection in human blood serum with the relative standard deviation (RSD) of 7.41%, showing the high precision of the sensor in measuring real samples.
Collapse
|
33
|
Facile Synthesis of Hierarchical Porous Three-Dimensional Free-Standing MnCo 2O 4 Cathodes for Long-Life Li-O 2 Batteries. ACS APPLIED MATERIALS & INTERFACES 2017; 9:12355-12365. [PMID: 28326762 DOI: 10.1021/acsami.6b16090] [Citation(s) in RCA: 12] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/06/2023]
Abstract
Hierarchical porous three-dimensional MnCo2O4 nanowire bundles were obtained by a universal and low-cost hydrothermal method, which subsequently act as a carbon-free and binder-free cathode for Li-O2 cell applications. This system showed a high discharge capacity of up to 12 919 mAh g-1 at 0.1 mA cm-2 and excellent rate capability. Under constrained specific capacities of 500 and 1000 mAh g-1, Li-O2 batteries could be successfully operated for over 300 and 144 cycles, respectively. Moreover, their charge voltage was markedly decreased to about 3.5 V. Their excellent electrochemical performance is proposed to be related to the conductivity enhancements resulting from the hierarchical interconnected mesoporous/macroporous weblike structure of the hybrid MnCo2O4 cathode, which facilitated the electron and mass transport. More importantly, after 2 months of cycling, the microstructure of the cathode was maintained and a recyclability of over 200 cycles of the reassembled Li-O2 cells was achieved. The effects of the level of electrolyte and corrosion of the lithium anode during long-term cycling on the electrochemical property of Li-O2 cells have been explored. Furthermore, the nucleation process of the discharge product morphology has been investigated.
Collapse
|
34
|
Effects of Metal Composition and Ratio on Peptide-Templated Multimetallic PdPt Nanomaterials. ACS APPLIED MATERIALS & INTERFACES 2017; 9:8030-8040. [PMID: 28156088 DOI: 10.1021/acsami.6b11651] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/06/2023]
Abstract
It can be difficult to simultaneously control the size, composition, and morphology of metal nanomaterials under benign aqueous conditions. For this, bioinspired approaches have become increasingly popular due to their ability to stabilize a wide array of metal catalysts under ambient conditions. In this regard, we used the R5 peptide as a three-dimensional template for formation of PdPt bimetallic nanomaterials. Monometallic Pd and Pt nanomaterials have been shown to be highly reactive toward a variety of catalytic processes, but by forming bimetallic species, increased catalytic activity may be realized. The optimal metal-to-metal ratio was determined by varying the Pd:Pt ratio to obtain the largest increase in catalytic activity. To better understand the morphology and the local atomic structure of the materials, the bimetallic PdPt nanomaterials were extensively studied by transmission electron microscopy, extended X-ray absorption fine structure spectroscopy, X-ray photoelectron spectroscopy, and pair distribution function analysis. The resulting PdPt materials were determined to form multicomponent nanostructures where the Pt component demonstrated varying degrees of oxidation based upon the Pd:Pt ratio. To test the catalytic reactivity of the materials, olefin hydrogenation was conducted, which indicated a slight catalytic enhancement for the multicomponent materials. These results suggest a strong correlation between the metal ratio and the stabilizing biotemplate in controlling the final materials morphology, composition, and the interactions between the two metal species.
Collapse
|
35
|
Metal–organic frameworks-derived porous carbon/Co3O4 composites for rechargeable lithium–oxygen batteries. Electrochim Acta 2017. [DOI: 10.1016/j.electacta.2017.01.121] [Citation(s) in RCA: 45] [Impact Index Per Article: 6.4] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/17/2022]
|
36
|
MOF-derived RuO2/Co3O4heterojunctions as highly efficient bifunctional electrocatalysts for HER and OER in alkaline solutions. RSC Adv 2017. [DOI: 10.1039/c6ra25810g] [Citation(s) in RCA: 90] [Impact Index Per Article: 12.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/27/2022] Open
Abstract
A RuO2/Co3O4heterojunction catalyst with a perfect OER and HER overpotential in 1 M KOH solution was synthesized. It contains only a small amount of precious metal oxides but demonstrates a better performance than most reported Co3O4-based electrocatalysts.
Collapse
|
37
|
Zinc diphosphide nanowires: bismuth nanocrystal-seeded growth and their use as high-capacity lithium ion battery anodes. CrystEngComm 2017. [DOI: 10.1039/c6ce02206e] [Citation(s) in RCA: 15] [Impact Index Per Article: 2.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/11/2023]
|
38
|
A Metal-Organic Framework Derived Porous Cobalt Manganese Oxide Bifunctional Electrocatalyst for Hybrid Na-Air/Seawater Batteries. ACS APPLIED MATERIALS & INTERFACES 2016; 8:32778-32787. [PMID: 27934150 DOI: 10.1021/acsami.6b10082] [Citation(s) in RCA: 18] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/03/2023]
Abstract
Spinel-structured transition metal oxides are promising non-precious-metal electrocatalysts for oxygen electrocatalysis in rechargeable metal-air batteries. We applied porous cobalt manganese oxide (CMO) nanocubes as the cathode electrocatalyst in rechargeable seawater batteries, which are a hybrid-type Na-air battery with an open-structured cathode and a seawater catholyte. The porous CMO nanocubes were synthesized by the pyrolysis of a Prussian blue analogue, Mn3[Co(CN)6]2·nH2O, during air-annealing, which generated numerous pores between the final spinel-type CMO nanoparticles. The porous CMO electrocatalyst improved the redox reactions, such as the oxygen evolution/reduction reactions, at the cathode in the seawater batteries. The battery that used CMO displayed a voltage gap of ∼0.53 V, relatively small compared to that of the batteries employing commercial Pt/C (∼0.64 V) and Ir/C (∼0.73 V) nanoparticles and without any catalyst (∼1.05 V) at the initial cycle. This improved performance was due to the large surface area (catalytically active sites) and the high oxidation states of the randomly distributed Co and Mn cations in the CMO. Using a hard carbon anode, the Na-metal-free seawater battery exhibited a good cycle performance with an average discharge voltage of ∼2.7 V and a discharge capacity of ∼190 mAh g-1hard carbon during 100 cycles (energy efficiencies of 74-79%).
Collapse
|
39
|
Bioinspired M-13 bacteriophage-based photonic nose for differential cell recognition. Chem Sci 2016; 8:921-927. [PMID: 28572902 PMCID: PMC5452260 DOI: 10.1039/c6sc02021f] [Citation(s) in RCA: 39] [Impact Index Per Article: 4.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/09/2016] [Accepted: 11/05/2016] [Indexed: 01/27/2023] Open
Abstract
A bioinspired M-13 bacteriophage-based photonic nose was developed for differential cell recognition.
A bioinspired M-13 bacteriophage-based photonic nose was developed for differential cell recognition. The M-13 bacteriophage-based photonic nose exhibits characteristic color patterns when phage bundle nanostructures, which were genetically modified to selectively capture vapor phase molecules, are structurally deformed. We characterized the color patterns of the phage bundle nanostructure in response to cell proliferation via several biomarkers differentially produced by cells, including hydrazine, o-xylene, ethylbenzene, ethanol and toluene. A specific color enables the successful identification of different types of molecular and cellular species. Our sensing technique utilized the versatile M-13 bacteriophage as a building block for fabricating bioinspired photonic crystals, which enables ease of fabrication and tunable selectivity through genetic engineering. Our simple and versatile bioinspired photonic nose could have possible applications in sensors for human health and national security, food discrimination, environmental monitoring, and portable and wearable sensors.
Collapse
|
40
|
Engineered phages for electronics. Biosens Bioelectron 2016; 85:964-976. [DOI: 10.1016/j.bios.2016.05.086] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/15/2016] [Revised: 05/29/2016] [Accepted: 05/30/2016] [Indexed: 11/26/2022]
|
41
|
Identification of Endocrine Disrupting Chemicals using a Virus-Based Colorimetric Sensor. Chem Asian J 2016; 11:3097-3101. [DOI: 10.1002/asia.201601079] [Citation(s) in RCA: 23] [Impact Index Per Article: 2.9] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/04/2016] [Revised: 09/05/2016] [Indexed: 12/31/2022]
|
42
|
|
43
|
Abstract
Soon after their discovery in the early 20th century, bacteriophages were recognized to have great potential as antimicrobial agents, a potential that has yet to be fully realized. The nascent field of phage therapy was adversely affected by inadequately controlled trials and the discovery of antibiotics. Although the study of phages as anti-infective agents slowed, phages played an important role in the development of molecular biology. In recent years, the increase in multidrug-resistant bacteria has renewed interest in the use of phages as antimicrobial agents. With the wide array of possibilities offered by genetic engineering, these bacterial viruses are being modified to precisely control and detect bacteria and to serve as new sources of antibacterials. In applications that go beyond their antimicrobial activity, phages are also being developed as vehicles for drug delivery and vaccines, as well as for the assembly of new materials. This review highlights advances in techniques used to engineer phages for all of these purposes and discusses existing challenges and opportunities for future work.
Collapse
|
44
|
Abstract
This review provides an overview of recent developments in "chemical virology." Viruses, as materials, provide unique nanoscale scaffolds that have relevance in chemical biology and nanotechnology, with diverse areas of applications. Some fundamental advantages of viruses, compared to synthetically programmed materials, include the highly precise spatial arrangement of their subunits into a diverse array of shapes and sizes and many available avenues for easy and reproducible modification. Here, we will first survey the broad distribution of viruses and various methods for producing virus-based nanoparticles, as well as engineering principles used to impart new functionalities. We will then examine the broad range of applications and implications of virus-based materials, focusing on the medical, biotechnology, and energy sectors. We anticipate that this field will continue to evolve and grow, with exciting new possibilities stemming from advancements in the rational design of virus-based nanomaterials.
Collapse
|
45
|
Abstract
Long fascinating to biologists, viruses offer nanometer-scale benchtops for building molecular-scale devices and materials. Viruses tolerate a wide range of chemical modifications including reaction conditions, pH values, and temperatures. Recent examples of nongenetic manipulation of viral surfaces have extended viruses into applications ranging from biomedical imaging, drug delivery, tissue regeneration, and biosensors to materials for catalysis and energy generation. Chemical reactions on the phage surface include both covalent and noncovalent modifications, including some applied in conjunction with genetic modifications. Here, we survey viruses chemically augmented with capabilities limited only by imagination.
Collapse
|
46
|
Biomimetic and Bioinspired Synthesis of Nanomaterials/Nanostructures. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2016; 28:2099-147. [PMID: 26729639 DOI: 10.1002/adma.201503215] [Citation(s) in RCA: 175] [Impact Index Per Article: 21.9] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/03/2015] [Revised: 09/09/2015] [Indexed: 05/13/2023]
Abstract
In recent years, due to its unparalleled advantages, the biomimetic and bioinspired synthesis of nanomaterials/nanostructures has drawn increasing interest and attention. Generally, biomimetic synthesis can be conducted either by mimicking the functions of natural materials/structures or by mimicking the biological processes that organisms employ to produce substances or materials. Biomimetic synthesis is therefore divided here into "functional biomimetic synthesis" and "process biomimetic synthesis". Process biomimetic synthesis is the focus of this review. First, the above two terms are defined and their relationship is discussed. Next different levels of biological processes that can be used for process biomimetic synthesis are compiled. Then the current progress of process biomimetic synthesis is systematically summarized and reviewed from the following five perspectives: i) elementary biomimetic system via biomass templates, ii) high-level biomimetic system via soft/hard-combined films, iii) intelligent biomimetic systems via liquid membranes, iv) living-organism biomimetic systems, and v) macromolecular bioinspired systems. Moreover, for these five biomimetic systems, the synthesis procedures, basic principles, and relationships are discussed, and the challenges that are encountered and directions for further development are considered.
Collapse
|
47
|
Fe/Fe3C decorated 3-D porous nitrogen-doped graphene as a cathode material for rechargeable Li–O2 batteries. Electrochim Acta 2016. [DOI: 10.1016/j.electacta.2016.01.134] [Citation(s) in RCA: 31] [Impact Index Per Article: 3.9] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/22/2022]
|
48
|
Two-dimensional graphene-like MoSe2 nanosheets anchored on hollow carbon nanofibers as a cathode catalyst for rechargeable Li–O2 batteries. RSC Adv 2016. [DOI: 10.1039/c5ra27634a] [Citation(s) in RCA: 13] [Impact Index Per Article: 1.6] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/21/2022] Open
Abstract
MoSe2@HCNF hybrids are used as the catalyst of Li–O2 batteries and exhibit superior catalytic activity. The more catalytic active sites and the enhanced electronic conductivity make the MoSe2@HCNF hybrids exhibit improved catalytic activity.
Collapse
|
49
|
NiFe-layered double hydroxides: a bifunctional O2 electrode catalyst for non-aqueous Li–O2 batteries. RSC Adv 2016. [DOI: 10.1039/c6ra19054e] [Citation(s) in RCA: 24] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/21/2022] Open
Abstract
An improved Li–O2 battery that exhibited a lower voltage gap and better cycle performance using NiFe-LDH. This result, although preliminary opens-up the possibilities of using LDHs as a promising catalyst for Li–O2 battery systems.
Collapse
|
50
|
Ru-decorated knitted Co3O4nanowires as a robust carbon/binder-free catalytic cathode for lithium–oxygen batteries. NEW J CHEM 2016. [DOI: 10.1039/c6nj01364c] [Citation(s) in RCA: 17] [Impact Index Per Article: 2.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/21/2023]
Abstract
Li–O2batteries show superior electrochemical performance with a knitted structured Co3O4/Ru cathode which is mechanically stable and catalytically active.
Collapse
|