An investigative review of the expanded capabilities of thermal/optical techniques for measuring carbonaceous aerosols and beyond

Carbonaceous aerosols primarily comprise organic carbon (OC) and black carbon (BC). Thermal-optical analysis (TOA) is the most commonly used method for separating carbonaceous aerosols into OC and EC (BC is referred to as elemental carbon EC, in this method). Advances in hardware design and algorithms have expanded the capabilities of TOA beyond just distinguishing OC and EC. However, a comprehensive understanding of the enhanced functionality of TOA is still lacking. This study provides the first comprehensive review of the TOA technique, highlighting expanded capabilities to measure brown carbon (BrC), mass-absorption efficiency, absorption enhancement, source contributions, and refined OC/EC split points. This review discusses the principles, advantages, and limitations of these advancements. Furthermore, the TOA system anticipates further advancements through integration with other instruments, establishing correlations between EC values obtained from different TOA instruments/protocols, correlating between BrC measurements from TOA and non-TOA methods, and developing an algorithm to quantify BrC from progressive absorption Ångström exponent (AAE) values. This review enhances the understanding of the TOA system and its implication for air quality and atmospheric radiation research.

A review of quantification methods for light absorption enhancement of black carbon aerosol

Black carbon (BC) is a distinct type of carbonaceous aerosol that has a significant impact on the environment, human health, and climate. A non-BC material coating on BC can alter the mixing state of the BC particles, which considerably enhances the mass absorption efficiency of BC by directing more energy toward the BC cores (lensing effect). A lot of methods have been reported for quantifying the enhancement factor (Eabs), with diverse results. However, to the best of our knowledge, a comprehensive review specific to the quantification methods for Eabs has not been systematically performed, which is unfavorable for the evaluation of obtained results and subsequent radiative forcing. In this review, quantification methods are divided into two broad categories, direct and indirect, depending on whether experimental removal of the coating layer from an aged carbonaceous particle is required. The direct methods described include thermal peeling, solvent dissolution, and optical virtual exfoliation, while the indirect methods include intercept-linear regression fitting, minimum R squared, numerical simulation, and empirical value. We summarized the principles, procedures, virtues, and limitations of the major Eabs quantification methods and analyzed the current problems in the determination of Eabs. We pointed out what breakthroughs are needed to improve or innovate Eabs quantification methods, particularly regarding the need to avoid the influence of brown carbon, develop a broadband Eabs quantification scheme, quantify the Eabs values for the emissions of low-efficiency combustions, measure the Eabs of particles in a high-humidity environment, design a real-time monitor of Eabs by a proper combination of mature techniques, and make more use of artificial intelligence for better Eabs quantification. This review deepens the understanding of Eabs quantification methods and benefits the estimation of the contribution of BC to radiative forcing using climate models.

Temporal and Spatial Variations of Satellite-Based Aerosol Optical Depths, Angstrom Exponent, Single Scattering Albedo, and Ultraviolet-Aerosol Index over Five Polluted and Less-Polluted Cities of Northern India: Impact of Urbanization and Climate Change

It is widely acknowledged that factors such as population growth, urbanization's quick speed, economic growth, and industrialization all have a role in the atmosphere's rising aerosol concentration. In the current work, we assessed and discussed the findings of a thorough analysis of the temporal and spatial variations of satellite-based aerosol optical parameters such as Aerosol Optical Depth (AOD), Angstrom Exponent (AE), Single Scattering Albedo (SSA), and Ultraviolet-Aerosol Index (UV-AI), and their concentration have been investigated in this study over five polluted and less-polluted cities of northern India during the last decade 2011–2020. The temporal variation of aerosol optical parameters for AOD ranging from 0.2 to 1.8 with decadal mean 0.86 ± 0.36 for Patna region shows high value with a decadal increasing trend over the study area due to rise in aerosols combustion of fossil fuels, huge vehicles traffic, and biomass over the past ten years. The temporal variation of AE ranging from 0.3 to 1.8 with decadal mean 1.72 ± 0.11 for Agra region shows high value as compared to other study areas, which indicates a comparatively higher level of fine-mode aerosols at Agra. The temporal variation of SSA ranging from 0.8 to 0.9 with decadal mean 0.92 ± 0.02 for SSA shows no discernible decadal pattern at any of the locations. The temporal variation of UV-AI ranging from -1.01 to 2.36 with decadal mean 0.59 ± 0.06 for UV-AI demonstrates a rising tendency, with a noticeable rise in Ludhiana, which suggests relative dominance of absorbing dust aerosols over Ludhiana. Further, to understand the impact of emerging activities, analyses were done in seasonality. For this aerosol climatology was derived for different seasons, i.e., Winter, Pre-Monsoon, Monsoon, and Post-Monsoon. High aerosol was observed in Winter for the study areas Patna, Delhi, and Agra which indicated the particles major dominance of burning aerosol from biomass; and the worst in Monsoon and Post-Monsoon for the Tehri Garhwal and Ludhiana study areas which indicated most of the aerosol concentration is removed by rainfall. After that, we analyzed the correlation among all the parameters to better understand the temporal and spatial distribution characteristics of aerosols over the selected region. The value of r for AOD (550 nm) for regions 2 and 1(0.80) shows a strong positive correlation and moderately positive for the regions 3 and 1 (0.64), mostly as a result of mineral dust carried from arid western regions. The value of r for AE (412/470 nm) for region 3 and (0.40) shows a moderately positive correlation, which is the resultant of the dominance of fine-mode aerosol and negative for the regions 5 and 1 (− 0.06). The value of r for SSA (500 nm) for regions 2 and 1 (0.63) shows a moderately positive correlation, which explains the rise in big aerosol particles, which scatters sun energy more efficiently, and the value of r for UV-AI for regions 1 and 2 shows a strong positive correlation (0.77) and moderately positive for the regions 3 and 1 (0.46) which indicates the absorbing aerosols present over the study region.

Multi-angular polarimetric remote sensing to pinpoint global aerosol absorption and direct radiative forcing

Quantitative estimations of atmospheric aerosol absorption are rather uncertain due to the lack of reliable information about the global distribution. Because the information about aerosol properties is commonly provided by single-viewing photometric satellite sensors that are not sensitive to aerosol absorption. Consequently, the uncertainty in aerosol radiative forcing remains one of the largest in the Assessment Reports of the Intergovernmental Panel on Climate Change (IPCC AR5 and AR6). Here, we use multi-angular polarimeters (MAP) to provide constraints on emission of absorbing aerosol species and estimate global aerosol absorption optical depth (AAOD) and its climate effect. Our estimate of modern-era mid-visible AAOD is 0.0070 that is higher than IPCC by a factor of 1.3-1.8. The black carbon instantaneous direct radiative forcing (BC DRF) is +0.33 W/m² [+0.17, +0.54]. The MAP constraint narrows the 95% confidence interval of BC DRF by a factor of 2 and boosts confidence in its spatial distribution.

Enhanced Light Absorption and Radiative Forcing by Black Carbon Agglomerates

The climate models of the Intergovernmental Panel on Climate Change list black carbon (BC) as an important contributor to global warming based on its radiative forcing (RF) impact. Examining closely these models, it becomes apparent that they might underpredict significantly the direct RF for BC, largely due to their assumed spherical BC morphology. Specifically, the light absorption and direct RF of BC agglomerates are enhanced by light scattering between their constituent primary particles as determined by the Rayleigh-Debye-Gans theory interfaced with discrete dipole approximation and recent relations for the refractive index and lensing effect. The light absorption of BC is enhanced by about 20% by the multiple light scattering between BC primary particles regardless of the compactness of their agglomerates. The resulting light absorption agrees very well with the observed absorption aerosol optical depth of BC. ECHAM-HAM simulations accounting for the realistic BC morphology and its coatings reveal high direct RF = 3-5 W/m² in East, South Asia, sub-Sahara, western Africa, and the Arabian peninsula. These results are in agreement with satellite and AERONET observations of RF and indicate a regional climate warming contribution by 0.75-1.25 °C, solely due to BC emissions.

Global Analysis of Atmospheric Transmissivity Using Cloud Cover, Aridity and Flux Network Datasets

Atmospheric transmissivity (τ) is a critical factor in climatology, which affects surface energy balance, measured at a limited number of meteorological stations worldwide. With the limited availability of meteorological datasets in remote areas across different climatic regions, estimation of τ is becoming a challenging task for adequate hydrological, climatic, and crop modeling studies. The availability of solar radiation data is comparatively less accessible on a global scale than the temperature and precipitation datasets, which makes it necessary to develop methods to estimate τ. Most of the previous studies provided region specific datasets of τ, which usually provide local assessments. Hence, there is a necessity to give the empirical models for τ estimation on a global scale that can be easily assessed. This study presents the analysis of the τ relationship with varying geographic features and climatic factors like latitude, aridity index, cloud cover, precipitation, temperature, diurnal temperature range, and elevation. In addition to these factors, the applicability of these relationships was evaluated for different climate types. Thus, empirical models have been proposed for each climate type to estimate τ by using the most effective factors such as cloud cover and aridity index. The cloud cover is an important yet often overlooked factor that can be used to determine the global atmospheric transmissivity. The empirical relationship and statistical indicator provided the best performance in equatorial climates as the coefficient of determination (r2) was 0.88 relatively higher than the warm temperate (r2 = 0.74) and arid regions (r2 = 0.46). According to the results, it is believed that the analysis presented in this work is applicable for estimating the τ in different ecosystems across the globe.

Simulation study on the indirect effect of sulfate on the summer climate over the eastern China monsoon region

In this study, we designed a sensitivity test using the half number concentration of sulfate in the nucleation calculation process to study the aerosol-cloud interaction (ACI) of sulfate on clouds, precipitation, and monsoon intensity in the summer over the eastern China monsoon region (ECMR) with the National Center for Atmospheric Research Community Atmosphere Model version 5. Numerical experiments show that the ACI of sulfate led to an approximately 30% and 34% increase in the cloud condensation nuclei and cloud droplet number concentrations, respectively. Cloud droplet effective radius below 850 hPa decreased by approximately 4% in the southern ECMR, while the total liquid water path increased by 11%. The change in the indirect radiative forcing due to sulfate at the top of the atmosphere in the ECMR during summer was − 3.74 W·m⁻². The decreased radiative forcing caused a surface cooling of 0.32 K and atmospheric cooling of approximately 0.3 K, as well as a 0.17 hPa increase in sea level pressure. These changes decreased the thermal difference between the land and sea and the gradient of the sea-land pressure, leading to a weakening in the East Asian summer monsoon (EASM) and a decrease in the total precipitation rate in the southern ECMR. The cloud lifetime effect has a relatively weaker contribution to summer precipitation, which is dominated by convection. The results show that the ACI of sulfate was one possible reason for the weakening of the EASM in the late 1970s.

Estimation of radiative forcing and heating rate based on vertical observation of black carbon in Nanjing, China

Owing to a lack of vertical observations, the impacts of black carbon (BC) on radiative forcing (RF) have typically been analyzed using ground observations and assumed profiles. In this study, a UAV platform was used to measure high-resolution in-situ vertical profiles of BC, fine particles (PM_2.5), and relevant meteorological parameters in the boundary layer (BL). Further, a series of calculations using actual vertical profiles of BC were conducted to determine its impact on RF and heating rate (HR). The results show that the vertical distributions of BC were strongly affected by atmospheric thermodynamics and transport. Moreover. Three main types of profiles were revealed: Type I, Type II, Type III, which correspond to homogenous profiles (HO), negative gradient profiles (NG), and positive gradient profiles (PG), respectively. Types I and II were related to the diurnal evolution of the BL, and Type III was caused by surrounding emissions from high stacks and regional transport. There were no obvious differences in RF calculated for HO profiles and corresponding surface BC concentrations, unlike for NG and PG profiles. RF values calculated using surface BC concentrations led to an overestimate of 13.2 W m^-2 (27.5%, surface) and 18.2 W m^-2 (33.4%, atmosphere) compared to those calculated using actual NG profiles, and an underestimate of approximately 15.4 W m^-2 (35.0%, surface) and 16.1 W m^-2 (29.9%, atmosphere) compared to those calculated using actual PG profiles. In addition, the vertical distributions of BC HR exhibited clear sensitivity to BC profile types. Daytime PG profiles resulted in a positive vertical gradient of HR, which may strengthen temperature inversion at high altitudes. These findings indicate that calculations that use BC surface concentrations and ignore the vertical distribution of BC will lead to substantial uncertainties in the effects of BC on RF and HR.

Long-Term Variation of Black Carbon Absorption Aerosol Optical Depth from AERONET Data over East Asia

Absorption aerosol optical depth induced by black carbon (AAODBC) was retrieved using the depolarization ratio and single scattering albedo provided by the Aerosol Robotic Network (AERONET) inversion products over East Asia. Our analysis considered AERONET data from six sites in East Asia that are mostly affected by anthropogenic pollution, black carbon (BC) emissions, and natural mineral dust, during the period 2001–2018. We identified a rapid reduction in total aerosol optical depth (AODT) of −0.0106 yr−1 over Beijing, whereas no considerable trend was observed at the Korean and Japanese sites. The long-term data for AAODBC showed decreasing trends at all sites. We conclude that successful emission control policies were the major underlying driver of AODT and AAODBC reductions over East Asia, particularly in China, during the study period. Values of the AAODBC/AODT ratio revealed that, although these policies were successful, the Chinese government needs to undertake stricter measures toward reducing BC emissions. We found that AAODBC follows seasonal trends, peaking in the colder months. This suggests that in East Asia, particularly in China, domestic coal burning is still of concern.

Entanglement of near-surface optical turbulence to atmospheric boundary layer dynamics and particulate concentration: implications for optical wireless communication systems

Localized reduction in optical turbulence due to enhanced atmospheric heating caused by the solar absorption of aerosol black carbon (BC) is reported. Immediate response of atmospheric turbulence to BC-induced atmospheric warming strongly depends on the available solar radiation (time of the day), BC concentration, and atmospheric boundary layer dynamics. Besides the significant climate implications of a reduction in turbulence kinetic energy, a large reduction in the refractive index structure parameter (Cn2) resulting from BC-induced warming would affect the atmospheric propagation of laser beams. Interestingly, aerosols contribute significantly (up to 25%) to the signal deterioration in optical wireless communication systems during convectively stable atmospheric conditions when higher signal-to-noise ratios are expected otherwise due to the reduced thermal convection. Competing effects of the fractional contributions of aerosol extinction and scintillations on beam attenuation are reported; daytime being largely dominated by scintillation effects while the nighttime being dependent on the ambient aerosol concentration as well. We put forward the entanglement of optical turbulence to aerosol concentration, atmospheric boundary layer dynamics, and surface-reaching solar radiation, and discuss the possible implications for optical propagation.

Morphological and radiative characteristics of soot aggregates: Experimental and numerical research

The study is aimed at investigating the radiative properties of soot aggregates at determined morphological features using both experimental and numerical methods. Soot aggregates collected from air monitoring stations in different locations were examined. The locations were divided into three groups. The first group (Case 1) included the coastal and industrial zone; the second group (Case 2) consisted of small and large cities; and the third group (Case 3) included areas in the neighbourhood of thermal power plants. The absorbance measurements of the soot aggregates were conducted in the visible and near-infrared spectra, and in the wavelength range of 2 μm-20 μm. The samples were characterised by scanning electron microscopy (SEM), and their radiative properties were assessed using the discrete dipole approximation (DDA) for numerically generated fractal aggregates with two popular refractive indices of m = 1.60 + 0.60i and m = 1.90 + 0.75i. Calculations were conducted for primary particles in point-contact, with 20% overlapping and with a coating (50% and 80%) in the wavelength range of 0.4–1.064 μm. The largest measured absorbance values in both the winter and summer seasons were found in the cities in Case 1, and the x-ray diffraction (XRD) phases of the samples were also presented. The radiative properties of the aggregates, i.e., D_f = 1.78 and k_f = 2.0 representing Case 3, were close to those of aggregates with D_f = 2.1 and k_f = 2.35 representing Case 1 in the investigated wavelength range. The calculated radiative properties and the experimental absorbance measurements for point-contact and overlapping situations showed the same trend in the examined wavelengths. The absorbance properties of the samples of coastal and industrial zones were distinctively higher than others in the wavelength range of 2 μm-20 μm which could be attributed to the PAH effects.

A Short Note on the Potential of Utilization of Spectral AERONET-Derived Depolarization Ratios for Aerosol Classification

We herein present the spectral linear particle depolarization ratios (δp) from an Aerosol Robotics NETwork (AERONET) sun/sky radiometer with respect to the aerosol type. AERONET observation sites, which are representative of each aerosol type, were selected for our study. The observation data were filtered using the Ångström exponent (Å), fine-mode fraction (FMF) and single scattering albedo (ω) to ensure that the obtained values of δp were representative of each aerosol condition. We report the spectral δp values provided in the recently released AERONET version 3 inversion product for observation of the following aerosol types: dust, polluted dust, smoke, non-absorbing, moderately-absorbing and high-absorbing pollution. The AERONET-derived δp values were generally within the range of the δp values measured from lidar observations for each aerosol type. In addition, it was found that the spectral variation of δp differed according to the aerosol type. From the obtained results, we concluded that our findings provide potential insight into the identification and classification of aerosol types using remote sensing techniques.

Strong impact of wildfires on the abundance and aging of black carbon in the lowermost stratosphere

Unique information about the abundance and evolution of wildfire-emitted black carbon (BC) in the lowermost part of the stratosphere (LMS) was obtained from long-term airborne measurements made in cooperation with Lufthansa through the Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container (CARIBIC) project, part of the In-service Aircraft for a Global Observing System (IAGOS) framework. Our results demonstrate that wildfires can dramatically increase BC mass concentration in the LMS, substantially enhance regional climate forcing, and are a challenge for model simulations. Climate change is expected to increase the frequency and spread of wildfires. Thus, recording a present-day baseline with extensive and long-term measurements should help to constrain model estimations of the climate impact of BC and foster our fundamental understanding of future climate change.

Wildfires inject large amounts of black carbon (BC) particles into the atmosphere, which can reach the lowermost stratosphere (LMS) and cause strong radiative forcing. During a 14-month period of observations on board a passenger aircraft flying between Europe and North America, we found frequent and widespread biomass burning (BB) plumes, influencing 16 of 160 flight hours in the LMS. The average BC mass concentrations in these plumes (∼140 ng·m⁻³, standard temperature and pressure) were over 20 times higher than the background concentration (∼6 ng·m⁻³) with more than 100-fold enhanced peak values (up to ∼720 ng·m⁻³). In the LMS, nearly all BC particles were covered with a thick coating. The average mass equivalent diameter of the BC particle cores was ∼120 nm with a mean coating thickness of ∼150 nm in the BB plume and ∼90 nm with a coating of ∼125 nm in the background. In a BB plume that was encountered twice, we also found a high diameter growth rate of ∼1 nm·h⁻¹ due to the BC particle coatings. The observed high concentrations and thick coatings of BC particles demonstrate that wildfires can induce strong local heating in the LMS and may have a significant influence on the regional radiative forcing of climate.

Modeling of Aerosol Radiation-Relevant Parameters in the Troposphere of Siberia on the Basis of Empirical Data

The paper presents the generalized empirical model of the aerosol optical characteristics in the lower 5-km layer of the atmosphere of West Siberia. The model is based on the data of long-term airborne sensing of the vertical profiles of the angular scattering coefficient, aerosol disperse composition, as well as the content of absorbing particles. The model provides for retrieval of the aerosol optical characteristics in visible and near IR wavelength ranges (complex refractive index, scattering and absorption coefficients, optical depth, single scattering albedo, and asymmetry factor of the scattering phase function). The main attention in the presented version of the model is given to two aspects: The study of the effect of the size spectrum of the absorbing substance in the composition of aerosol particles on radiative-relevant parameters (the single scattering albedo (SSA) and the asymmetry factor (AF)) and the consideration of different algorithms for taking into account the relative humidity of air. The ranges of uncertainty of SSA and AF at variations in the modal radius of the absorbing fraction at different altitudes in the troposphere are estimated.

Variations in FINN Emissions of Particulate Matters and Associated Carbonaceous Aerosols from Remote Sensing of Open Biomass Burning over Northeast China during 2002–2016

Various particulate matters (PM) and associated carbonaceous aerosols released from open biomass burning (including open straw burning, grass and forest fires) are major sources of atmospheric pollutants. Northeast China is a central region with high forest and grass coverage, as well as an intensive agricultural area. In this study, the FINN (Fire INventory from Ncar) emission data was used to analyze the spatiotemporal variations of PM and associated carbonaceous aerosol component (PM2.5, PM10, OC and BC) emissions from open biomass burning in Northeast China from 2002 to 2016. The results show that the total amount of annual PM2.5, PM10, OC and BC emissions was estimated to be 59.0, 70.6, 31.5, and 4.3 kilotons, respectively, from open biomass burning over Northeast China, averaged from 2002 to 2016, with significant inter-annual variations in amplitudes from 28.0 to 122.3, 33.7 to 144.1, 15.0 to 65.0, and 2.1 to 8.6 kilotons. The regional PM2.5, PM10, OC and BC emissions showed significant seasonal variations with highest emissions in spring (with a seasonal peak in April), followed by autumn (with a seasonal peak in October), summer, and winter in Northeast China; high emissions were concentrated in the forests and grasslands with natural fires, as well as over agricultural areas with crop straw burning from human activities. The PM2.5, PM10, OC and BC emissions over forest areas presented decreasing trends, while the emissions over farmlands showed increasing trends in Northeast China during 2002–2016; this reflects on the dominance of biomass burning that shifted from forestland with natural fires to farmlands with increasing human activities. Three key meteorological drivers—strong near-surface wind speed, high air temperature and low relative humidity—were identified as having significant positive impacts on the inter-annual variations of PM2.5, PM10, OC and BC emissions from open biomass burning in Northeast China.

Black carbon radiative forcing at TOA decreased during aging

During aging processing, black carbon (also called soot) particles may tend to be mixed with other aerosols, and highly influence their radiative forcing. In this study, freshly emitted soot particles were simulated as fractal aggregates composed of small spherical primary monomers. After aging in the atmosphere, soot monomers were coated by a thinly layer of sulfate as thinly coated soot particles. These soot particles were entirely embedded into large sulfate particle by further aging, and becoming heavily coated soot particles. In clear-sky conditions, black carbon radiative forcing with different aging states were investigated for the bottom and top of atmosphere (BOA and TOA). The simulations showed that black carbon radiative forcing increased at BOA and decreased at TOA after their aging processes. Thinly and heavily coated states increased up to ~12% and ~35% black carbon radiative forcing at BOA, and black carbon radiative forcing at TOA can reach to ~20% and ~100% smaller for thinly and heavily coated states than those of freshly emitted states, respectively. The effect of aging states of black carbon radiative forcing was varied with surface albedo, aerosol optical depth and solar zenith angles. These findings would be helpful for the assessments of climate change.

Effects of mixing states on the multiple-scattering properties of soot aerosols

The radiative properties of soot aerosols are highly sensitive to the mixing states of black carbon particles and other aerosol components. Light absorption properties are enhanced by the mixing state of soot aerosols. Quantification of the effects of mixing states on the scattering properties of soot aerosol are still not completely resolved, especially for multiple-scattering properties. This study focuses on the effects of the mixing state on the multiple scattering of soot aerosols using the vector radiative transfer model. Two types of soot aerosols with different mixing states such as external mixture soot aerosols and internal mixture soot aerosols are studied. Upward radiance/polarization and hemispheric flux are studied with variable soot aerosol loadings for clear and haze scenarios. Our study showed dramatic changes in upward radiance/polarization due to the effects of the mixing state on the multiple scattering of soot aerosols. The relative difference in upward radiance due to the different mixing states can reach 16%, whereas the relative difference of upward polarization can reach 200%. The effects of the mixing state on the multiple-scattering properties of soot aerosols increase with increasing soot aerosol loading. The effects of the soot aerosol mixing state on upwelling hemispheric flux are much smaller than in upward radiance/polarization, which increase with increasing solar zenith angle. The relative difference in upwelling hemispheric flux due to the different soot aerosol mixing states can reach 18% when the solar zenith angle is 75°. The findings should improve our understanding of the effects of mixing states on the optical properties of soot aerosols and their effects on climate. The mixing mechanism of soot aerosols is of critical importance in evaluating the climate effects of soot aerosols, which should be explicitly included in radiative forcing models and aerosol remote sensing.

Effect of traffic and driving characteristics on morphology of atmospheric soot particles at freeway on-ramps

Vehicles represent a major source of soot in urban environments. Knowledge of the morphology and mixing of soot particles is fundamental to understand their potential health and climatic impacts. We investigate 5738 single particles collected at six different cloverleaf freeway on-ramps in Southern Michigan, using 2D images from scanning electron microscopy. Of those, 3364 particles are soot. We present an analysis of the morphological and mixing properties of those soot particles. The relative abundance of soot particles shows a positive association with traffic density (number of vehicles per minute). A classification of the mixing state of freshly emitted soot particles shows that most of them are bare (or thinly coated) (72%) and some are partly coated (22%). We find that the fractal dimension of soot particles (one of the most relevant morphological descriptors) varies from site to site, and increases with increasing vehicle specific power that represents the driving/engine load conditions, and with increasing percentage of vehicles older than 15 years. Our results suggest that driving conditions, and vehicle age and type have significant influence on the morphology of soot particles.

Identification of the sources and geographic origins of black carbon using factor analysis at paired rural and urban sites

Black carbon particles, composed of forms of elemental carbon (EC), contribute significantly to regional and global warming. The origins of EC were examined in southeastern Canada as part of a source apportionment study using positive matrix factorization (PMF), performed on long-term PM2.5 chemical speciation data collected at two paired rural and urban sites. Comparisons of the urban and rural sites revealed a previously unrecognized EC-rich factor that accounted for 41-56% of the total EC in this region. This factor was characterized by the more thermally stable EC fractions that exhibit strong light absorption characteristics. While these EC fractions are often attributed to local diesel emissions, this interpretation was rejected for several reasons. The EC-rich factor was present in similar temporal patterns at both the high-traffic urban and low-traffic rural sites across this 600 km region. The geographic origins of the EC-rich factor were found to be Ohio and Western Pennsylvania regions with heavy industry and multiple coal-based electrical generating stations. The direct radiative forcing due to this EC-rich factor was roughly estimated to be +0.2 W m(-2), which represented a substantial portion of the aerosol induced warming in the region. Thus, this region was impacted by an important unidentified source of EC associated with long-range transport.

Vertical profiles of black carbon aerosols over the urban locations in South India

Vertical profiles of black carbon (BC) aerosol were determined from aircraft measurements under the Cloud Aerosol Interaction and Precipitation Enhancement Experiment (CAIPEEX) program conducted by the Indian Institute of Tropical Meteorology, India during 2009 over Bangalore and Hyderabad in south India. BC mass loadings decreased approximately monotonically from 10(3) to 10(4) ng/m(3) at the surface to ~10(2) ng/m(3) at an altitude of about 7 km; although layers at intermediate levels containing anomalously high BC loadings were frequently encountered that were attributed mainly to the convective transport from surface sources accompanied by changes in the local boundary layer and atmospheric stability. In addition, as evidenced from air mass back trajectories; long range transport from distant sources contributed to some anomalous spikes in BC concentration. The presence of BC in cloud forming regions of the free troposphere could have important implications for cloud microphysics and subsequent rainfall mechanism over this region. Apart from this, the effects on human health are equally important.

Deployment of coal briquettes and improved stoves: possibly an option for both environment and climate

The use of coal briquettes and improved stoves by Chinese households has been encouraged by the government as a means of reducing air pollution and health impacts. In this study we have shown that these two improvements also relate to climate change. Our experimental measurements indicate that if all coal were burned as briquettes in improved stoves, particulate matter (PM), organic carbon (OC), and black carbon (BC) could be annually reduced by 63 +/- 12%, 61 +/- 10%, and 98 +/- 1.7%, respectively. Also, the ratio of BC to OC (BC/OC) could be reduced by about 97%, from 0.49 to 0.016, which would make the primary emissions of household coal combustion more optically scattering. Therefore, it is suggested that the government consider the possibility of: (i) phasing out direct burning of bituminous raw-coal-chunks in households; (ii) phasing out simple stoves in households; and, (iii) financially supporting the research, production, and popularization of improved stoves and efficient coal briquettes. These actions may have considerable environmental benefits by reducing emissions and mitigating some of the impacts of household coal burning on the climate. International cooperation is required both technologically and financially to accelerate the emission reduction in the world.

Low fractal dimension cluster-dilute soot aggregates from a premixed flame

Using a novel morphology segregation technique, we observed minority populations ( approximately 3%) of submicron-sized, cluster-dilute fractal-like aggregates, formed in the soot-formation window (fuel-to-air equivalence ratio of 2.0-3.5) of a premixed flame, to have mass fractal dimensions between 1.2 and 1.51. Our observations disagree with previous observations of a universal mass fractal dimension of approximately 1.8 for fractal-like aerosol aggregates formed in the dilute-limit via three-dimensional diffusion-limited cluster aggregation processes. A hypothesis is presented to explain this observation. Subject to verification of this hypothesis, it may be possible to control the fractal dimension and associated properties of aggregates in the cluster-dilute limit through application of a static electric field during the aggregation process.

Morphological and light-absorption characteristics of individual BC particles collected in an urban seaside area at Tokaimura, eastern central Japan

To observe surface morphology and light-absorption property of different black carbon (BC) particles, different-sized aerosols were collected in Tokaimura (36.27 degrees N, 140.36 degrees E), an urban seaside area of eastern central Japan, using a high-volume Andersen type sampler during a whole year (Jan. to Dec. in 2004). The morphology of individual BC particle separated from different-sized aerosols was observed with Scanning Electron Microscope with Energy Dispersive X-ray Spectrometer (SEM-EDX) and four types of morphology were observed: 50 nm spherical particles, micrometer-sized plates with homogeneous surfaces, micrometer-sized spherical particles with homogeneous surfaces and micrometer-sized spherical particles with small holes on surfaces. The light-absorption property of BC particles with different morphology has been determined by infrared spectrometry (IRS) with a photoacoustic technique in a region of 400-4000 wavenumbers (cm(-1)). All morphology BC particles showed a strong light-absorption during 500-3000 wavenumbers (cm(-1)) with two strong broad peaks in 750-1100 and 1200-2200 wavenumbers (cm(-1)), implying that all morphology BC particles can absorb a significant part of thermal infrared emitted from the earth (wavelength 4000-50,000 nm). The seasonal variation and the size-distribution of aerosols and its chemical components (e.g. C, Na, Cl, NH(4)(+), NO(3)(-), SO(4)(2-), Al, Ca, Mg and Fe) were also measured in this study. More than 55% of non-inorganic carbon (OC+BC) in the atmosphere was detected in the aerosols with a size smaller than 1.1 microm and the concentration of non-inorganic carbon in the atmosphere showed only a faint variation during a whole year, although the concentrations of total aerosols and its chemical components exhibited a distinct variation.