Toward a mechanistic understanding of adsorption behavior of phenol onto a novel activated carbon composite

Adsorption of phenol and methylene blue contaminants onto high-performance catalytic activated carbon from biomass residues

Organic contaminants from wastewater toxicity to the environment has increased during the last few decades and, therefore, there is an urgent need to decontaminate wastewater prior to disposal. This study aimed to create a high surface area catalytic activated carbon (AC) under same carbonization conditions for phenol and methylene blue (organic wastewater) decontamination. Moringa oleifera husk (MH), sesame husk (SH), and baobab husk (BH) were used to prepare activated carbon for the removal of methylene blue (MB) and phenol (Ph). After characterization of the adsorbent, the BET surface areas of the M. oleifera husk activated carbon (MHC), sesame husk activated carbon (SHC), and baobab husk activated carbon (BHC) were 1902.30 m2/g, 1115.90 m2/g, and 1412.40 m2/g, respectively. Mono-adsorption and binary-adsorption systems were studied for Ph and MB adsorption. Furthermore, the effect of initial organic waste concentration, contact time, pH, temperature and AC dosage, on adsorption capacity were studied. The mono adsorption system isotherms and kinetics studies used to analyze Phenol and MB adsorption best fitted Langmuir and pseudo-second-order models. The Freundlich isotherm and pseudo-second-order model best fitted the experimental data for the binary-adsorption system. The high maximum adsorption capacities of organic waste for the single and binary systems were 352.25-855.96 mg/g and 348.90-456.39 mg/g, respectively. The results showed that the high surface activated carbon produced had the potential to adsorb high concentrations of MB and Phenol contaminants.

Simultaneous removal of ammonium, phosphate, and phenol via self-assembled biochar composites CBCZrOFe3O4 and its utilization as soil acidity amelioration

ABSTRACTHigh concentrations of ammonium, phosphate, and phenol are recognized as water pollutants that contribute to the degradation of soil acidity. In contrast, small quantities of these nutrients are essential for soil nutrient cycling and plant growth. Here, we reported composite materials comprising biochar, chitosan, ZrO, and Fe3O4, which were employed to mitigate ammonium, phosphate, and phenol contamination in water and to lessen soil acidity. Batch adsorption experiments were conducted to assess the efficacy of the adsorbents. Initially, comparative studies on the simultaneous removal of NH4, PO4, and phenol using CB (biochar), CBC (biochar + chitosan), CBCZrO (biochar + chitosan + ZrO), and CBCZrOFe3O4 (biochar + chitosan + ZrO + Fe3O4) were conducted. The results discovered that CBCZrOFe3O4 exhibited the highest removal percentage among the adsorbents (P < 0.05). Adsorption data for CBCZrOFe3O4 were well fitted to the second-order kinetic and Freundlich isotherm models, with maximum adsorption capacities of 112.65 mg/g for NH4, 94.68 mg/g for PO4 and 112.63 mg/g for phenol. Subsequently, the effect of CBCZrOFe3O4-loaded NH4, PO4, and phenol (CBCZrOFe3O4-APP) on soil acidity was studied over a 60-day incubation period. The findings showed no significant changes (P < 0.05) in soil exchangeable acidity, H+, Mg, K, and Na. However, there was a substantial increase in the soil pH, EC, available P, CEC, N-NH4, and N-NO3. A significant reduction was also observed in the available soil exchangeable Al and Fe (P < 0.05). This technique demonstrated multi-functionality in remediating water pollutants and enhancing soil acidity.

Enhanced adsorption of phenolic compounds using biomass-derived high surface area activated carbon: Isotherms, kinetics and thermodynamics

The progress of industrial and agricultural pursuits, along with the release of inadequately treated effluents especially phenolic pollutant, has amplified the pollution load on environment. These organic compounds pose considerable challenges in both drinking water and wastewater systems, given their toxicity, demanding high oxygen and limited biodegradability. Thus, developing an eco-friendly, low-cost and highly efficient adsorbent to treat the organic pollutants has become an important task. The present investigation highlights development of a novel adsorbent (CFPAC) by activation of Cassia fistula pod shell for the purpose of removing phenol and 2,4-dichlorophnenol (2,4-DCP). The significant operational factors (dosage, pH, concentration, temperature, speed) were also investigated. The factors such as pH = 2 and T = 20°C were found to be significant at 1.6 g/L and 0.6 g/L dosage for phenol and 2,4-DCP respectively. Batch experiments were further conducted to study isotherms, kinetic and thermodynamics studies for the removal of phenol and 2,4-DCP. The activated carbon was characterised as mesoporous (specific surface area 1146 m2/g, pore volume = 0.8628 cc/g), amorphous and pHPZC = 6.4. At optimum conditions, the maximum sorption capacity for phenol and 2,4-DCP were 183.79 mg/g and 374.4 mg/g respectively. The adsorption isotherm was better conformed to Redlich Peterson isotherm (phenol) and Langmuir isotherm (2,4-DCP). The kinetic study obeyed pseudo-second-order type behaviour for both the pollutants with R2 > 0.999. The thermodynamic studies and the value of isosteric heat of adsorption for both the pollutants suggested that the adsorption reaction was dominated by physical adsorption (ΔHx < 80 kJ/mol). Further, the whole process was feasible, exothermic and spontaneous in nature. The overall studies suggested that the activated carbon synthesised from Cassia fistula pods can be a promising adsorbent for phenolic compounds.

Preparation of low-cost sludge-based highly porous biochar for efficient removal of refractory pollutants from agrochemical and pharmaceutical wastewater

Producing a high-performance sludge biochar through a feasible method is a great challenge and is crucial for practicability. Herein, we reported a highly porous sludge biochar synthesized from agrochemical-pharmaceutical and municipal sludge blends through a novel pyrolysis-acid treatment-post pyrolysis method. The optimized biochar named ASMS91 obtained interconnected pores with a total pore volume of 0.894 cm3/g and a surface area of 691.4 m2/g through extended acid wash and subsequent post-pyrolysis, which is superior to non-activated sludge biochar. ASMS91 removed 45.3 % of wastewater COD (156 mg/L) in 24 h, which was rapid and higher performance than commercial activated carbon (1000 iodine number). This outstanding performance is due to its high adsorption ability of long-chain aliphatic compounds (e.g., 2,4-Di-tert-butylphenol, neophytadiene and eicosane) into mesopores, which accounts for 71.8 % of pore filling. ASMS91 was highly recyclable, and adsorption was reduced by only 5.3 % after the 4th cycle. It also outperformed other sludge biochar in literature in removing perfluorooctanoic acid (PFOA), 6:2 fluorotelomer sulfonate (6:2 FTS), sulfamethoxazole, methylene blue, and methylene orange. Finally, the feasibility of our proposed method was validated by a brief techno-economic analysis. This feasible approach may support future research regarding sludge valorization and low-cost chemical wastewater treatment.

Efficient adsorptive removal of 2,4-dichlorophenoxyacetic acid (2,4-D) using biomass derived magnetic activated carbon nanocomposite in synthetic and simulated agricultural runoff water

This study focused on evaluating the efficacy of a magnetic activated carbon material (CPAC@Fe3O4) derived from pods of copper pod tree in adsorbing the toxic herbicide, 2,4- (2,4-D) from aqueous solutions. The synthesized CPAC@Fe3O4 adsorbent, underwent various characterization techniques. FESEM images indicated a rough surface, incorporating iron oxide nanoparticles, while EDS analysis confirmed the presence of elements like Fe, O, and C. Notably, the CPAC@Fe3O4 exhibited high surface area (749.10 m2/g) and pore volume (0.5351 cm³/g), confirming its mesoporous nature. XRD investigations identified distinct signals associated with graphitic carbon and magnetite nanoparticles, while VSM analysis verified its magnetic properties with a high magnetic saturation value (2.72 emu/g). The adsorption process was exothermic, with a decrease in adsorption capacity at higher temperatures. Freundlich isotherm provided the best fit for the adsorption, and the pseudo-second-order equation effectively described the kinetics. Remarkably, the maximum adsorption capacity ranged from 246.43 to 261.03 mg/g, surpassing previously reported values. The ΔH° value (-8.67 kJ/mol) suggested a physisorption mechanism, and the negative ΔG° values established the spontaneous nature. Furthermore, the synthesized adsorbent demonstrated exceptional reusability, allowing for up to five cycles of adsorption-desorption operations. When applied to simulated agricultural runoff, CPAC@Fe3O4 showcased a significant adsorption capacity of 160.71 mg/g for 50 mg/L 2,4-D, using a 0.2 g/L dosage at pH 2. This study showcased the transformation of copper pod biomass into a valuable magnetic nanoadsorbent capable of efficiently eliminating the noxious 2,4-D pollutant from aqueous environments.

Assessment of chromite ore wastes for methylene blue adsorption: Isotherm, kinetic, thermodynamic studies, ANN, and statistical physics modeling

This research investigates the adsorption potential of chrysotile and lizardite, two minerals derived from chromite ore wastes, for the uptake of Methylene Blue (MB) dye from waste streams. The characterization of these minerals involves XRD, XRF, FTIR, and SEM. Results confirm the dominance of polymorphic magnesium silicate minerals, specifically chrysotile and lizardite, in the samples. The FTIR spectra reveal characteristic vibration bands confirming the presence of these minerals. The SEM analysis depicts irregular surfaces with broken and bent edges, suggesting favorable morphologies for adsorption. N2 adsorption-desorption isotherms indicate mesoporous structures with Type IV pores in both adsorbents. The Central Composite Design approach is employed to optimize MB adsorption conditions, revealing the significance of contact time, adsorbent mass, and initial MB concentration. The proposed models exhibit high significance, with F-values and low p-values indicating the importance of the studied factors. Experimental validation confirms the accuracy of the models, and the optimum conditions for MB adsorption are determined. The influence of solution acidity on MB uptake is investigated, showing a significant enhancement at higher pH values. Isothermal studies indicate Langmuir and Freundlich models as suitable descriptions for MB adsorption onto chrysotile and lizardite. The maximum adsorption capacities of MB for chrysotile and lizardite were found to be 352.97 and 254.85, respectively. Kinetic studies reveal that the pseudo-first-order model best describes the adsorption process. Thermodynamic analysis suggests an exothermic and spontaneous process. Statistical physics models further elucidate the monolayer nature of adsorption. Additionally, an artificial neural network is developed, exhibiting high predictive capability during training and testing stages. The reusability of chrysotile and lizardite is demonstrated through multiple regeneration cycles, maintaining substantial adsorption potential. Therefore, this research provides comprehensive insights into the adsorption characteristics of chrysotile and lizardite, emphasizing their potential as effiective and reusable sorbents for MB uptake from wastewater.

Insight into Cu (II) adsorption on pyrochar and hydrochar resultant from Acacia Senegal waste for wastewater decontamination

Acacia Senegal waste (ASW) is remaining biomass following gum Arabic harvesting and has no use mentioned in the literature as of yet. This study aims to convert ASW into valuable biochar via two comparative thermal and hydrothermal techniques, which include pyrochar ASW at 300 °C (PC ASW300) and hydrochar ASW at 180 °C (HC ASW180), respectively, for Cu (II) adsorption from aqueous solutions. SEM-EDS, FTIR, XRD, and XPS were used to characterize the biochar. Adsorption performance was studied as a function of pH, contact time, and adsorbent concentration. Adsorption kinetics were best fit for a pseudo-second-order model. And thermodynamics studies revealed that Cu (II) on biochar was endothermic, spontaneous, and best fitted to the Langmuir isotherm model. Pyrochar adsorption capacity (31.93 mg g-1) was seven times that of hydrochar (5.45 mg g-1). ASW treated with phosphorus (PC H3PO4 and HC H3PO4) prior to the carbonization altered the pore structure and surface functional groups as well (O-P-O, P-CH3, and P-OH) of biochar. It was found that treating with phosphorous acid increased adsorption capacity to 141.7 mg g-1 and 22.24 mg g-1 for PC H3PO4 and HC H3PO4, respectively. The surface functional groups of biochar resulted from lignin, alkaloids, and polysaccharides combined with Cu (II) during the adsorption process via surface complexation accompanied by π-electron interaction and Cu (II) reduction. These findings shed light on the ASW biochar potential as a new green cost-effective adsorbent and drew an insightful understanding of Cu (II) adsorption performance and mechanism. It is concluded that ASW-derived biochar is highly effective and a promising alternative for Cu (II) decontamination from wastewater.

Excess secondary sludge reuse by H2O2 thermal dehydration

The excess of activated sludge generated in municipal wastewater treatment plants constitutes one of the challenging problems facing modern society. The high-water content of this waste makes difficult the transport, disposal, and management of these solids. In this work, activated sludge excess from a secondary clarifier has been dehydrated by means of a combination of temperature and hydrogen peroxide treatment. Three main operating variables have been considered to affect sludge dewaterability and filterability. Temperature (120-180 °C), hydrogen peroxide dose (0.01-0.03 M), and treatment time (20-60 min) influence have been assessed by completing a 15-run Box Behnken experimental design. Different output variables (water content, resistance to filtration, sedimentation volumetric index, extracellular polymeric substances, etc.) have been monitored. Generally, temperature seems to be the most influencing parameter to obtain a dehydrated sludge with acceptable management/disposal characteristics (sludge volume reduction and filterability). In line with the concept of circular economy, an attempt has been conducted to obtain a sustainable biosorbent from the dehydrated sludge generated in the previous stage. Optimum conditions of carbonization and activation revealed that the solid obtained at 400 °C by using ammonium nitrate as activation agent was the most efficient absorbent to eliminate some model compounds from water (namely, phenol, ofloxacin, and diuron); however, a clear improvement margin in the synthesis is foreseen.

Development of activated carbons derived from wastes: coffee grounds and olive stones as potential porous materials for air depollution

Agro-industrial byproducts and food waste necessitate an environmentally friendly way of reducing issues related to their disposal; it is also necessary to recover as much new raw material from these resources as possible, especially when we consider their potential usage as a precursor for preparing depolluting materials, such as activated carbon. In this work, coffee grounds and olive stones were chosen as precursors and the adsorption capacity of the obtained porous carbons for volatile organic compounds (VOCs) was studied. Microporous activated carbons (ACs) were prepared using chemical (K2CO3) and physical (CO2) activation. The influence of the activation process, type, and time of activation was also investigated. Measurements of VOCs adsorption were performed, and methyl-ethyl-ketone (MEK) and toluene were chosen as the model pollutants. The surface areas and total pore volumes of 1487 m2/g and 0.53 cm3/g and 870 m2/g and 0.22 cm3/g for coffee ground carbons and olive stone carbons, respectively, were obtained via chemical activation, whereas physical activation yielded values of 716 m2/g and 0.184 cm3/g and 778 cm2 g-1 and 0.205 cm3/g, respectively. As expected, carbons without activation (biochars) showed the smallest surface area, equal to 331 m2/g and 251 m2/g, and, hence, the lowest adsorption capacity. The highest adsorption capacity of MEK (3210 mg/g) and toluene (2618 mg/g) was recorded for chemically activated coffee grounds. Additionally, from the CO2 isotherms recorded at a low pressure (0.03 bar) and 0 °C, the maximum CO2 adsorption capacity was equal to 253 mg/g.

Spherical Lignin-Derived Activated Carbons for the Adsorption of Phenol from Aqueous Media

In this work, a synthesis and activation path, which enabled the preparation of spherical activated carbon from a lignin precursor, characterized by high adsorption capacity in the removal of phenolic compounds from water, was successfully developed. Two industrial by-products, i.e., Kraft lignin and sodium lignosulfonate, were used to form spherical nanometric lignin grains using pH and solvent shift methods. The obtained materials became precursors to form porous activated carbons via chemical activation (using K2CO3 or ZnCl2 as activating agents) and carbonization (in the temperature range of 600-900 °C). The thermal stabilization step at 250 °C was necessary to ensure the sphericity of the grains during high-temperature heat treatment. The study investigated the influence of the type of chemical activator used, its quantity, and the method of introduction into the lignin precursor, along with the carbonization temperature, on various characteristics including morphology (examined by scanning electron microscopy), the degree of graphitization (evaluated by powder X-ray diffraction), the porosity (assessed using low-temperature N2 adsorption), and the surface composition (analyzed with X-ray photoelectron spectroscopy) of the produced carbons. Finally, the carbon materials were tested as adsorbents for removing phenol from an aqueous solution. A conspicuous impact of microporosity and a degree of graphitization on the performance of the investigated adsorbents was found.

Insights into kinetics, thermodynamics, and mechanisms of chemically activated sunflower stem biochar for removal of phenol and bisphenol-A from wastewater

This study synthesized a highly efficient KOH-treated sunflower stem activated carbon (KOH-SSAC) using a two-step pyrolysis process and chemical activation using KOH. The resulting material exhibited exceptional properties, such as a high specific surface area (452 m2/g) and excellent adsorption capacities for phenol (333.03 mg/g) and bisphenol A (BPA) (365.81 mg/g). The adsorption process was spontaneous and exothermic, benefiting from the synergistic effects of hydrogen bonding, electrostatic attraction, and stacking interactions. Comparative analysis also showed that KOH-SSAC performed approximately twice as well as sunflower stem biochar (SSB), indicating its potential for water treatment and pollutant removal applications. The study suggests the exploration of optimization strategies to further enhance the efficiency of KOH-SSAC in large-scale scenarios. These findings contribute to the development of improved materials for efficient water treatment and pollution control.

Enhanced persulfate activation by ethylene glycol-mediated bimetallic sulfide for imidacloprid degradation

CuFeS2 is regarded as a promising catalyst for heterogeneous activation to remove organic contaminants in wastewater. However, effects of solvents in regulating material synthesis and catalytic activity are still not clear. Herein, we reported the role of water, ethanol, ethylene glycol (EG), glycerol, and polyethylene glycol 200 on the synthesis of CuFeS2 micro-flowers and their performance in activating persulfate (PS) to remove imidacloprid (IMI) pesticide. The results showed that the solvent had an effect on the morphology, crystallinity, yields, specific surface areas and unpaired electrons of CuFeS2 micro-flowers. The degradation experiments revealed the efficient catalytic activity of EG-mediated CuFeS2 for heterogeneous PS activation. SO4•- and •OH were identified in EG-CuFeS2/PS system and •OH (90.4%) was the dominant reactive species. Meanwhile, stable 20% of η[PMSO2] (the molar ratio of PMSO2 generation to PMSO consumption) was achieved and demonstrated that Fe(IV) was also involved in the degradation process. Moreover, S2- promoted the cycling of Fe3+/Fe2+ and Cu2+/Cu+, enhancing the synergistic activation and reusability of the catalyst. Density functional theory (DFT) calculations verified that PS was adsorbed by Fe atom and electron transfer occurred on the catalyst surface. Three possible degradation pathways of IMI were proposed by analysis of the degradation intermediates and their toxicities were evaluated by ECOSAR. This study not only provides a theoretical foundation for catalyst design, but also promotes the industrial application of bimetallic sulfide Fenton-like catalysts for water management.

The potential of self-activated carbon for adsorptive removal of toxic phenoxyacetic acid herbicide from water

Phenoxyacetic acid herbicides are widely used in agriculture for controlling weeds. These organic compounds are persistent and recalcitrant, often contaminating water and soil. Therefore, we studied five pristine biochars (BCs), and southern yellow pine (SYP) based self-activated carbon (SAC) for the adsorptive removal of 2,4-Dichlorophenoxyacetic acid (2,4-D) herbicide. Among the tested adsorbents, SYP-SAC-15 demonstrated higher (>90%) 2,4-D removal from water. The SYP-SAC-15 was produced using a facile and green route where the biomass pyrolysis gases worked as activating agents creating a highly porous structure with a surface area of 1499.79 m2/g. Different adsorption kinetics and isotherm models were assessed for 2,4-D adsorption on SYP-SAC-15, where the data fitted best to pseudo-second order (R2 > 0.999) and Langmuir (R2 > 0.991) models, respectively. Consequently, the adsorption process was mainly dominated by the chemisorption mechanism with monolayer coverage of SYP-SAC-15 surface with 2,4-D molecules. At the optimum pH of 2, the maximum 2,4-D adsorption capacity of SYP-SAC-15 reached 471.70 mg/g. Furthermore, an increase in the water salinity demonstrated a positive influence on 2,4-D adsorption, whereas humic acid (HA) showed a negative impact on 2,4-D adsorption. The regeneration ability of SYP-SAC-15 showed excellent performance by retaining 71.09% adsorption capability at the seventh adsorption-desorption cycle. Based on the operating pH, surface area, spectroscopic data, kinetics, and isotherm modeling, the adsorption mechanism was speculated. The 2,4-D adsorption on SYP-SAC-15 was mainly governed by pore filling, electrostatic interactions, hydrogen bonding, hydrophobic and π-π interactions.

Enhancing the efficiency of Ni(II), Cd(II), and Cu(II) adsorption from aqueous solution using schist/alginate composite: batch and continuous studies

The main aim of this research is focused on the synthesis of schist/alginate composite (SC/AL) adsorbent and its utilization for the removal of Ni(II), Cu(II), and Cd(II) from waste streams using batch and column processes. The characterization of developed adsorbent was performed by X-ray fluorescence, X-ray diffraction, FTIR, and BET analyses. The most influential operating parameters (pH, contact time, temperature and initial adsorbate concentration) on the adsorption capacity of pollutants were examined to evaluate the performance of developed adsorbent. The kinetic and equilibrium adsorption results at pH 5.0 indicated that SC/AL composite had good adsorption capacity (qmax) for Ni(II), Cu(II), and Cd(II) estimated at 124.79 mg/g, 111.78 mg/g, and 119.78 mg/g, respectively. From the kinetic viewpoint, the good fit of pseudo-first-order kinetic model to the kinetic adsorption data indicated that dominant interaction of heavy metals with SC/AL composite was physisorption. The results of thermodynamic studies indicated that the adsorption of heavy metals onto SC/AL composite was endothermic and spontaneous in nature. The adsorption capacity of developed adsorbent could still reach relatively 85% of the original one after completing fifth cycle. Therefore, the reusability results of SC/AL composite were quite satisfied, making the developed adsorbent a commercially attractive and green method. Finally, in column studies, the effect of initial concentration of pollutants at pH 5.0 on the removal of heavy metal ions was investigated. The Thomas and Yoon-Nelson models provided a satisfactory explanation for the results of column data.

ZnO doped C: Facile synthesis, characterization and photocatalytic degradation of dyes

Carbon doped ZnO nanoparticles have been synthesized from the thermal decomposition of Zinc citrate precursor. The precursor was synthesized from semi-solid paste and then subjected to calcination at 700 °C to produce ZnO nanoparticles. The precursor and ZnO were characterized by Fourier Transform Infrared Spectroscopy, UV-visible (UV-Vis) spectra, Transmission Electron Microscope, Field Emission Scanning Electron Microscope, Energy Dispersive Analysis by X-ray (EDAX), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The results ensured the formation of hexagonal 2D-ZnO nanoparticles with a layer thickness of 25 nm. The optical band gap of ZnO was determined and found to be 2.9 eV, which is lower than the bulk. Photocatalytic degradation of Fluorescein dye as an anionic dye and Rhodamine B as a cationic dye was evaluated via C-ZnO NPs under UV irradiation. ZnO displayed 99% degradation of Fluorescein dye after 240 min and a complete photocatalytic degradation of Rhodamine B dye after 120 min under UV irradiation.

Preparation and Characterization of Activated Carbon/Polymer Composites: A Review

Activated carbon (AC) and activated carbon fibers (ACFs) are materials with a large specific surface area and excellent physical adsorption properties due to their rich porous structure, and they are used as electrode materials to improve the performance of adsorbents or capacitors. Recently, multiple studies have confirmed the applicability of AC/polymer compo-sites in various fields by exploiting the unique physical and chemical properties of AC. As the excellent mechanical properties, stability, antistatic and electromagnetic interference (EMI) shielding functions of activated carbon/polymer composite materials were confirmed in recent studies, it is expected that activated carbon can be utilized as an ideal reinforcing material for low-cost polymer composite materials. Therefore, in this review, we would like to describe the fabrication, characterization and applicability of AC/polymer composites.

Nanoporous carbons based on coordinate organic polymers as an efficient and eco-friendly nano-sorbent for adsorption of phenol from wastewater

The major part of water pollutants includes of organic such as phenolic pollutant, thus there are every hazardous to environment. Present work is a comparative onto surface chemistry and adsorptive characteristics of coordinate organic polymer (Cop-150) and nanoporous carbon (NPC) prepared using solvothermal method. New NPC was successfully synthesized to remove of phenol. FT-IR, XRD, XPS, SEM, TGA, and BET techniques have been used to characterization and confirm physicochemical variation during preparing Cop-150 and NPC. Box-Behnken response surface methodology (BBRSM) was used to optimize four important factors of the pH (2-10), contact time (1-40 min), temperature (25-60 °C), and initial concentration of phenol (5-50 mg L-1). To analyze the data obtained from the adsorption of phenol by synthesized adsorbents, four linear, 2FI, quadratic and cubic models were examined, which the quadratic model was recognized as the best model. To the NPC the equal adsorption capacity 500 mg g-1 is achieved at the initial concentration of phenol = 49.252 mg L-1, contact time = 15.738 min, temperature = 28.3 °C, and pH 7.042. On the other hand, the adsorption capacity for Cop-150 in pH 4.638, the contact time = 19.695 min, the temperature = 56.8 °C, and the initial concentration of phenol = 6.902 mg L-1 was equal to 50 mg g-1. The experimental data at different conditions were investigated by some famous kinetic and isotherm models, which among them, were corresponded to the pseudo-second-order kinetic model and the Langmuir isotherm. Moreover, based to result of thermodynamics to the both Cop-150 and NPC, the adsorption process is exothermic and spontaneous. According to results the Cop-150 and NPC could be used for up to four and five cycles without significantly reducing their performance, respectively.

Enhanced adsorption of 2,4-dichlorophenoxyacetic acid using low-temperature carbonized Peltophorum pterocarpum pods and its statistical physics modeling

The usage of various herbicides in the agricultural field leads to water pollution which is a big threat to the environment. Herein, the pods of the Peltophorum pterocarpum tree were used as a cheap resource to synthesize activated carbon (AC) by low-temperature carbonization to remove 2,4-dichlorophenoxyacetic acid (2,4-D) - an abundantly used herbicide. The exceptional surface area (1078.34 m²/g), mesoporous structure, and the various functional groups of the prepared AC adsorbed 2,4-D effectively. The maximum adsorption capacity was 255.12 mg/g, significantly higher than the existing AC adsorbents. The adsorption data satisfactorily modelled using Langmuir and pseudo-second-order models. Also, the adsorption mechanism was studied using a statistical physics model which substantiated the multi-molecular interaction of 2,4-D with the AC. The adsorption energy (<20 kJ/mol) and thermodynamic studies (ΔH°: -19.50 kJ/mol) revealed the physisorption and exothermicity. The practical application of the AC was successfully tested in various waterbodies by spiking experiments. Hence, this work confirms that the AC prepared from the pods of P. pterocarpum can be applied as a potential adsorbent to remove herbicides from polluted waterbodies.