Gold-nanoparticle/organic linker films: self-assembly, electronic and structural characterisation, composition and vapour sensitivity

Cesium ion-guided detection of trichloroethylene in air

Whereas the close associations of cesium ion with organochlorine compounds have been previously documented, the present report is the first attempt to exploit these interactions to create a trichloroethylene (TCE)-selective sensor. Gold monolayer-protected clusters peripherally functionalized with Cs+ ions were used to prepare a chemiresistance film on MEMS-fabricated interdigitated electrodes. Vapor sensing properties of the cesium-rich chemiresistor were determined using a panel of chlorinated hydrocarbons including TCE as well as polar and non-polar VOCs for comparison. The sensor was selective and highly sensitive toward VOCs containing a 1,2-dichloro group at concentrations as low as 0.1 ppm. The results suggest the key interaction contributing to sensor response is a bidentate, metallocycle-like coordination of the 1,2-dichloro group to the cesium cations at the sensor surface.

Enhanced degradation of enoxacin using ferrihydrite-catalyzed heterogeneous photo-Fenton process

The ferrihydrite-catalyzed heterogeneous photo-Fenton reaction shows great potential for environmental remediation of fluoroquinolone (FQs) antibiotics. The degradation of enoxacin, a model of FQ antibiotics, was studied by a batch experiment and theoretical calculation. The results revealed that the degradation efficiency of enoxacin reached 89.7% at pH 3. The hydroxyl radical (∙OH) had a significant impact on the degradation process, with a cumulative concentration of 43.9 μmol L-1 at pH 3. Photogenerated holes and electrons participated in the generation of ∙OH. Eleven degradation products of enoxacin were identified, with the main degradation pathways being defluorination, quinolone ring and piperazine ring cleavage and oxidation. These findings indicate that the ferrihydrite-catalyzed photo-Fenton process is a valid way for treating water contaminated with FQ antibiotics.

Heading toward Miniature Sensors: Electrical Conductance of Linearly Assembled Gold Nanorods

Metal nanoparticles are increasingly used as key elements in the fabrication and processing of advanced electronic systems and devices. For future device integration, their charge transport properties are essential. This has been exploited, e.g., in the development of gold-nanoparticle-based conductive inks and chemiresistive sensors. Colloidal wires and metal nanoparticle lines can also be used as interconnection structures to build directional electrical circuits, e.g., for signal transduction. Our scalable bottom-up, template-assisted self-assembly creates gold-nanorod (AuNR) lines that feature comparably small widths, as well as good conductivity. However, the bottom-up approach poses the question about the consistency of charge transport properties between individual lines, as this approach leads to heterogeneities among those lines with regard to AuNR orientation, as well as line defects. Therefore, we test the conductance of the AuNR lines and identify requirements for a reliable performance. We reveal that multiple parallel AuNR lines (>11) are necessary to achieve predictable conductivity properties, defining the level of miniaturization possible in such a setup. With this system, even an active area of only 16 µm² shows a higher conductance (~10^-5 S) than a monolayer of gold nanospheres with dithiolated-conjugated ligands and additionally features the advantage of anisotropic conductance.

Tackling the Scalability Challenge in Plasmonics by Wrinkle-Assisted Colloidal Self-Assembly

Electromagnetic radiation of a certain frequency can excite the collective oscillation of the free electrons in metallic nanostructures using localized surface plasmon resonances (LSPRs), and this phenomenon can be used for a variety of optical and electronic functionalities. However, nanostructure design over a large area using controlled LSPR features is challenging and requires high accuracy. In this article, we offer an overview of the efforts made by our group to implement a wrinkle-assisted colloidal particle assembly method to approach this challenge from a different angle. First, we introduce the controlled wrinkling process and discuss the underlying theoretical framework. We then set out how the wrinkled surfaces are utilized to guide the self-assembly of colloidal nanoparticles of various surface chemistry, size, and shape. Subsequently, template-assisted colloidal self-assembly mechanisms and a general guide for particle assembly beyond plasmonics will be presented. In addition, we also discuss the collective plasmonic behavior in depth, including strong plasmonic coupling due to nanoscale gap size as well as magnetic mode excitation and demonstrate the potential applications of wrinkle-assisted colloidal particle assembly method in the field of mechanoresponsive metasurfaces and surface-enhanced spectroscopy. Lastly, a general perspective in the field of template-assisted colloidal assembly with regard to potential applications in plasmonic photocatalysis, solar cells, optoelectronics, and sensing devices is provided.

Assembly Behavior of Organically Interlinked Gold Nanoparticle Composite Films: A Quartz Crystal Microbalance Investigation

Thin films based on dodecylamine stabilized gold nanoparticles interlinked with different organic molecules are prepared by automatic layer-by-layer self-assembly in a microfluidic quartz crystal microbalance (QCM) cell, to obtain an in situ insight on the film formation by ligand/linker exchange reactions. The influence of interlinking functional groups and the length of the organic linker molecule on the assembly behavior is investigated. Alkyldithiols with different lengths are compared to alkyldiamines and alkylbisdithiocarbamates with a C8 alkylic molecular backbone. The stepwise layer-by-layer assembly occurs independently of the linker molecule, while the largest frequency changes always correspond to the gold nanoparticle step. During the solvent rinsing and ligand/linker exchange reaction step, the frequency is almost constant with slight increases or decreases dependent on the molar mass of the linker compared to the exchanged ligand. The assembly efficiency is higher for shorter molecules and for molecules with stronger interacting functional groups. The densities of the composite films are calculated from QCM data and independent thickness measurements. They reflect the higher fraction of organic material in the films comprising longer organic linkers. The plasmon resonance band of the gold nanoparticles in the final assemblies is measured with UV/vis spectroscopy. Band positions in films prepared from dithiols and diamines of comparable lengths are very similar, while the spectrum of the bisdithiocarbamate film exhibits a distinct blue-shift. This observation is explained by the longer molecular structure of the linker due to a larger binding group, in conjunction with a delocalization of particle charge on the organic molecule. Obtained results play an essential role in the understanding of thin film layer-by-layer self-assembly processes, and enable the formation of new gold nanoparticle networks with organic diamine and bisdithiocarbamate molecules.

Cross-Linked Gold-Nanoparticle Membrane Resonators as Microelectromechanical Vapor Sensors

We report a novel approach for the detection of volatile compounds employing electrostatically driven drumhead resonators as sensing elements. The resonators are based on freestanding membranes of alkanedithiol cross-linked gold nanoparticles (GNPs), which are able to sorb analytes from the gas phase. Under reduced pressure, the fundamental resonance frequency of a resonator is continuously monitored while the device is exposed to varying partial pressures of toluene, 4-methylpentan-2-one, 1-propanol, and water. The measurements reveal a strong, reversible frequency shift of up to ∼10 kHz, i.e., ∼5% of the fundamental resonance frequency, when exposing the sensor to toluene vapor with a partial pressure of ∼20 Pa. As this strong shift cannot be explained exclusively by the mass uptake in the membrane, our results suggest a significant impact of analyte sorption on the pre-stress of the freestanding GNP membrane. Thus, our findings point to the possibility of designing highly sensitive resonators, which utilize sorption induced changes in the membrane's pre-stress as primary transduction mechanism.

Electrostatically driven drumhead resonators based on freestanding membranes of cross-linked gold nanoparticles

Freestanding, nanometer-thin membranes of alkanedithiol cross-linked gold nanoparticles represent elastic, mechanically robust and electrically conductive materials, which are interesting for the fabrication of novel nano- and microelectromechanical devices. In this work we present the first electrostatically driven drumhead resonators based on such nanoparticle membranes. These circular membranes have a thickness of 33 to 52 nm, a diameter of either 50 μm or 100 μm, and are equally spaced from their back electrode by ∼10 μm. Using an interferometric nanovibration analyzer various vibrational modes with resonance amplitudes of up to several 100 nm could be detected when the membranes are excited by applying AC voltages (<30 V) with drive frequencies of up to 2 MHz. Further, spatial amplitude distributions of different vibrational modes could be imaged. The devices showed fundamental resonance frequencies in the high kHz range and quality factors Q up to ∼2000. Finally, vibrational spectra and observed mode patterns could be well interpreted using the theory for a clamped circular membrane with negligible bending stiffness. Our findings mark an important step towards the integration of freestanding gold nanoparticle composite membranes into electromechanical devices with various applications, such as novel types of pressure or mass sensors.

A template-confined fabrication of controllable gold nanoparticles based on the two-dimensional nanostructure of macrocycles

An amine-substituted macrocycle 6Y, a rigid hexagonal ring, self-assembled into a network architecture on the surface, which could be used as a molecular template to directly fabricate gold nanoparticles (AuNPs) with narrow size distribution (2.2 ± 0.1 nm).

Stabilizing catalytically active nanoparticles by ligand linking: toward three-dimensional networks with high catalytic surface area

A general approach for the linking of Pt nanoparticles (NPs) with bifunctional amine ligands (organic molecules with two amine groups) is presented that allows for the preparation of NP catalysts without inorganic supports and high densities of the catalytically active metal. Advantage was taken of the use of "unprotected" NPs, which enables us to prepare different ligand-functionalized NPs from the same particle batch and thus to relate changes of the resulting material properties exclusively to the influence of the ligand. Three bifunctional ligands with similar functional groups (amines) but different hydrocarbon skeletons were used and compared to monofunctional ligands of similar molecular structures (alkyl and aryl amines) showing significantly different material properties. Monofunctional molecules with minor steric demand cover almost completely the NP surface and lead to two-dimensional assembling of the NPs. In contrast, the use of bifunctional amine ligands leads to the formation of porous, three-dimensional NP networks (ligand-linked NPs) with a high density of ligand free surface atoms, thus enabling for the application as catalytic materials. The stabilizing effect of bifunctional ligands serves as an alternative to the use of inorganic support materials and enables for catalytic applications of ligand-linked NP networks.

Hydrophobic nanoparticle-based nanocomposite films using in situ ligand exchange layer-by-layer assembly and their nonvolatile memory applications

A robust method for preparing nanocomposite multilayers was developed to facilitate the assembly of well-defined hydrophobic nanoparticles (i.e., metal and transition metal oxide NPs) with a wide range of functionalities. The resulting multilayers were stable in both organic and aqueous media and were characterized by a high NP packing density. For example, inorganic NPs (including Ag, Au, Pd, Fe₃O₄, MnO₂) dispersed in organic media [corrected]were shown to undergo layer-by-layer assembly with amine-functionalized polymers to form nanocomposite multilayers while incurring minimal physical and chemical degradation of the inorganic NPs. In addition, the nanocomposite multilayer films formed onto flat and colloidal substrates could directly induce the adsorption of the electrostatically charged layers without the need for additional surface treatments. This approach is applicable to the preparation of electronic film devices, such as nonvolatile memory devices requiring a high memory performance (ON/OFF current ratio >10(3) and good memory stability).

Cross-linked gold nanoparticles on polyethylene: resistive responses to tensile strain and vapors

In this study, coatings of cross-linked gold nanoparticles (AuNPs) on flexible polyethylene (PE) substrates were prepared via layer-by-layer deposition and their application as strain gauges and chemiresistors was investigated. Special emphasis was placed on characterizing the influence of strain on the chemiresistive responses. The coatings were deposited using amine stabilized AuNPs (4 and 9 nm diameter) and 1,9-nonanedithiol (NDT) or pentaerythritol tetrakis(3-mercaptopropionate) (PTM) as cross-linkers. To prepare films with homogeneous optical appearance, it was necessary to treat the substrates with oxygen plasma directly before film assembly. SEM images revealed film thicknesses between ∼60 and ∼90 nm and a porous nanoscale morphology. All films showed ohmic I-V characteristics with conductivities ranging from 1 × 10⁻⁴ to 1 × 10⁻² Ω⁻¹ cm⁻¹, depending on the structure of the linker and the nanoparticle size. When up to 3% strain was induced their resistance increased linearly and reversibly (gauge factors: ∼20). A comparative SEM investigation indicated that the stress induced formation and extension of nanocracks are important components of the signal transduction mechanism. Further, all films responded with a reversible increase in resistance when dosed with toluene, 4-methyl-2-pentanone, 1-propanol or water vapor (concentrations: 50-10 000 ppm). Films deposited onto high density PE substrates showed much faster response-recovery dynamics than films deposited onto low density PE. The chemical selectivity of the coatings was controlled by the chemical nature of the cross-linkers, with the highest sensitivities (∼1 × 10⁻⁵ ppm⁻¹) measured with analytes of matching solubility. The response isotherms of all film/vapor pairs could be fitted using a Langmuir-Henry model suggesting selective and bulk sorption. Under tensile stress (1% strain) all chemiresistors showed a reversible increase in their response amplitudes (∼30%), regardless of the analytes' permittivity. Taking into consideration the thermally activated tunneling model for charge transport, this behavior was assigned to stress induced formation of nanocracks, which enhance the films' ability to swell in lateral direction during analyte sorption.

Gold nanoparticle chemiresistors operating in biological fluids

Functionalised gold nanoparticle (Au(NP)) chemiresistors are investigated for direct sensing of small organic molecules in biological fluids. The principle reason that Au(NP) chemiresistors, and many other sensing devices, have limited operation in biological fluids is due to protein and lipid fouling deactivating the sensing mechanism. In order to extend the capability of such chemiresistor sensors to operate directly in biofluids, it is essential to minimise undesirable matrix effects due to protein and lipidic components. Ultrafiltration membranes were investigated as semi-permeable size-selective barriers to prevent large biomolecule interactions with Au(NP) chemiresistors operating in protein-loaded biofluids. All of the ultrafiltration membranes protected the Au(NP) chemiresistors from fouling by the globular biomolecules, with the 10 kDa molecular weight cut-off size being optimum for operation in biofluids. Titrations of toluene in different protein-loaded fluids indicated that small molecule detection was possible. A sensor array consisting of six different thiolate-functionalised Au(NP) chemiresistors protected with a size-selective ultrafiltration membrane successfully identified, and discriminated the spoilage of pasteurised bovine milk. This proof-of-principle study demonstrates the on-chip protein separation and small metabolite detection capability, illustrating the potential for this technology in the field of microbial metabolomics. Overall, these results demonstrate that a sensor array can be protected from protein fouling with the use of a membrane, significantly increasing the possible application areas of Au(NP) chemiresistors ranging from the food industry to health services.

Chemiresistive sensing with chemically modified metal and alloy nanoparticles

This review describes the use of chemically modified pure and alloyed metal nanoparticles for chemiresistive sensing applications. Chemically modified metal nanoparticles consist of a pure or alloyed metallic core with some type of chemical coating. Researchers have studied the electronic properties of 1D, 2D, and 3D assemblies of chemically modified metal nanoparticles, and even single individual nanoparticles. The interaction with the analyte alters the conductivity of the sensitive material, providing a signal to measure the analyte concentration. This review focuses on chemiresistive sensing of a wide variety of gas- and liquid-phase analytes with metal nanoparticles coated with organothiols, ions, polymers, surfactants, and biomolecules. Different strategies used to incorporate chemically modified nanoparticles into chemiresistive sensing devices are reviewed, focusing on the different types of metal and alloy compositions, coatings, methods of assembly, and analytes (vapors, gases, liquids, biological materials), along with other important factors.

Thin film assemblies of molecularly-linked metal nanoparticles and multifunctional properties

The use of metal nanoparticles as building blocks toward thin film assembly creates intriguing opportunities for exploring multifunctional properties. Such an exploration requires the ability to engineer the size, shape, composition, and especially interparticle properties in nanoparticle assemblies for harnessing the collective properties of the nanoscale building blocks. This article highlights some of the important findings of our investigations of thin film assemblies of molecularly linked nanoparticles for exploiting their multifunctional and collective properties in molecular recognition and chemical sensing. The thermally activated processing approach presents a viable pathway for nanoengineering metal, alloy, and core-shell nanoparticles as building blocks. The molecular mediator-templating approach offers an effective strategy to thin film assemblies of the nanoscale building blocks that impart multifunctional properties. In such thin film assemblies, the interparticle interactions and structures dictate the correlation between the nanostructural parameters and the optical and electrical properties. By highlighting selected examples involving ligand-framework binding of ionic species at the film/liquid interface and electrical responses to molecular sorption at the film/gas interface, the multifunctional properties of the thin film assemblies are further discussed in terms of interparticle covalent, hydrogen bonding, ionic, or van der Waals interactions in a framework-type architecture for the creation of molecular recognition and chemical sensing sites that can be tuned chemically or electrochemically. Implications of these insights to expanding the exploration of nanoparticle thin film assemblies for a wide range of technological applications are also discussed.

Synthesis and characterization of thiosalicylic acid stabilized gold nanoparticles

We report the synthesis of photoluminescent Au nanoparticles of varying sizes stabilized with a carboxylate group terminated aromatic thiol, thiosalicylic acid. The formation of Au nanoparticles and its stabilization with the thiol has been characterized by different spectroscopic and thermal methods. The water solubility, along with the low degree of aggregation and photoluminescence, enhances their suitability for biological applications. The photoluminescence may be due to charge transfer of the Au core with the stabilizing ligand.

99% random telegraph signal-like noise in gold nanoparticle micro-stripes

In this paper, we report on a process to prepare gold nanoparticle stripes on SiO(2) by convective/capillary assembly without any patterning of the substrate. Electrical devices were then fabricated using stencil lithography in order to avoid any contamination. I(V) measurements at room temperature show that these stripes have an ohmic behavior between +/- 0.5 V with a resistivity ranging from one to two orders higher than the gold bulk value. Furthermore, I(V) and I(t) measurements reveal current fluctuations that were interpreted in terms of charging and discharging of nanoparticle islands leading to a very large electrostatic perturbation of current conduction paths. Unconventional relative amplitudes of up to 99% RTS fluctuations were observed.

Chemiresistive sensing of volatile organic compounds with films of surfactant-stabilized gold and gold-silver alloy nanoparticles

Here we describe the chemiresistive sensing of volatile organic compounds (VOCs) with films of chemically synthesized approximately 4 nm diameter Au and AuAg alloy nanoparticles (NPs) stabilized by a surfactant, tetraoctylammonium bromide (TOABr). The chemiresistive sensing properties were measured over a concentration range of 100 to 0.04% saturation for methanol (MeOH), ethanol (EtOH), 2-propanol (IPA), and toluene (Tol) vapor analytes and compared directly to the chemiresistive sensing properties of films of 1.6 nm diameter hexanethiolate (C6S)-coated Au monolayer-protected clusters (MPCs). Films of TOABr-stabilized Au NPs exhibit the opposite response compared to those of C6S-coated Au MPCs. The details are unclear, but the mechanism likely involves changes in capacitive charging in the film or improved conductive pathways through the Au NPs upon incorporation of VOCs into the film for the former as opposed to the well-known change in electron hopping conductivity for the latter. This leads to a decrease in resistance in the presence of VOCs for TOABr Au as opposed to an increase for C6S Au. The TOABr Au sensors are more sensitive, especially for polar analytes, and have greater long-term stability compared to C6S Au. The limit of detection (LOD) for films of TOABr-coated Au NPs is 3, 2, 12, and 37 ppm for IPA, MeOH, EtOH, and Tol, respectively, as compared to 106, 326, 242, and 48 for C6S Au. Films of TOABr-stabilized AuAg alloy NPs exhibit the same type of response, but the sensitivity decreases dramatically with increasing Ag content, showing that the metal composition of the NPs in the film plays a role in the sensing properties, which has not been well-recognized in the literature.

Multilayered gold-nanoparticle/polyimide composite thin film through layer-by-layer assembly

A novel type of composite thin film consisting of gold nanoparticles (AuNPs) and polymide (PI) was fabricated through layer-by-layer (LBL) assembly. To fabricate such films, bare AuNPs and a poly (amic acid) bearing pendant amine groups, namely, amino poly (amic acid) or APAA, were synthesized and assembled in an LBL fashion. Without any organic encapsulation layer on their surface, AuNPs were bound directly to APAA chains at the amine sites; X-ray photoelectron spectroscopy study suggested that the binding was based on a combined effect of metal-ligand coordination and electrostatic interaction, with the former dominating over the latter. An approximately linear growth of the film started from the second layer of AuNP as revealed by the UV-vis spectroscopy, and the degree of particle aggregation was higher in the first AuNP layer than in the subsequent layers due to the differences in the density of binding sites. The resultant assembly was heated to imidize the APAA, thereby creating a robust composite structure.

Gold Nanoparticle Chemiresistor Sensors: Direct Sensing of Organics in Aqueous Electrolyte Solution

A novel chemiresistor sensor for detection of organic analytes in high-conductivity aqueous electrolyte solution is reported. The chemiresistor sensor is based on thin films of gold nanoparticles capped with a 1-hexanethiol monolayer that is inkjet printed onto a microelectrode. In order for a change in nanoparticle film resistance to be measured, the electronic conduction must preferentially occur through the nanoparticle film rather than through the high-conductivity electrolyte solution. This was achieved by miniaturizing the chemiresistor device such that the double layer capacitance of the electrodes in contact with the electrolyte solution gives rise to a significantly larger impedance compared to the nanoparticle film resistance. This system was shown to be sensitive to simple organics dissolved in an aqueous electrolyte solution. The organic analytes, dissolved in the aqueous solution, partition into the hydrophobic nanoparticle film causing the nanoparticle film to swell, resulting in an increase in the low-frequency impedance of the sensor. An increase in the impedance, at 1 Hz, of the gold nanoparticle chemiresistor on exposure to toluene, dichloromethane, and ethanol dissolved in 1 M KCl solution was demonstrated with detection limits of 0.1, 10, and 3000 ppm, respectively. Titration curves over 3 orders of magnitude could be obtained for analytes such as toluene.

Model of Vapor-Induced Resistivity Changes in Gold−Thiolate Monolayer-Protected Nanoparticle Sensor Films

An investigation of the modulation of charge transport through thin films of n-octanethiolate monolayer-protected gold nanoparticles (MPN) induced by the sorption of organic vapors is presented. A model is derived that allows predictions of MPN-coated chemiresistor (CR) responses from vapor-film partition coefficients, and analyte densities and dielectric constants. Calibrations with vapors of 28 compounds collected from an array of CRs and a parallel thickness-shear-mode resonator are used to verify assumptions inherent in the model and to assess its performance. Results afford insights into the nature of the vapor-MPN interactions, including systematic variations in apparent film swelling efficiencies, and show that the model can predict CR responses typically to within 24%. Using CRs of different dimensions, vapor sensitivities are found to be virtually independent of the MPN film volume over a range of 104 (device-area x MPN layer thickness). Sensitivities vary inversely with analyte vapor pressure similarly for the two sensor types, but the CR sensor affords significantly greater signal-to-noise ratios, yielding calculated detection limits in the low-part-per-billion concentration range for several of the analytes tested. The implications of these results for implementing MPN-coated CR arrays as detectors in microanalytical systems are considered.

Exploiting Charge-Transfer Complexation for Selective Measurement of Gas-Phase Olefins with Nanoparticle-Coated Chemiresistors

Charge-transfer-mediated olefin-selective sensing by use of chemiresistors (CR) coated with composite films of n-octanethiolate-monolayer-protected gold nanoparticles (C8-MPN) and each of several square-planar PtCl2(olefin)(pyridine) coordination complexes is described. Where the gas-phase olefin analyte differs from that initially coordinated to Pt, olefin substitution occurs and is accompanied by a persistent shift in the composite film resistance. Commensurate changes in film mass are also observed with a similarly coated thickness shear mode resonator. Regeneration is possible by exposure to the initially complexed olefin gas or vapor. If the olefin analyte is the same as that initially coordinated to Pt, then a reversible charge-transfer interaction occurs that is accompanied by a decrease in film resistance (increase in film mass), which recovers spontaneously after removal of the olefin from the atmosphere above the sensor. This behavior differs from that of MPN-coated CRs lacking such Pt complexes, which invariably yield resistance increases upon exposure to nonpolar vapors. Red shifts in the UV-vis absorbance spectra of the PtCl2(olefin)(pyridine) complexes in solution upon addition of free olefin support the hypothesis that Pt-olefin coordination in the composite films creates temporary low-resistance pathways that compete effectively with the concurrent increase in tunneling resistance associated with swelling-induced separation of C8-MPN cores. Structurally analogous non-olefins produce only increases in film resistance. Selective measurement of styrene, ethylene, 1-octene, and 1,3-butadiene is illustrated. Olefin detection limits are reduced as much as 23 000-fold by inclusion of the corresponding Pt complex in the CR interface film. Composite films suffer a gradual loss of selectivity from decomposition of the Pt-olefin complex, apparently facilitated by a Au-Pt charge transfer.

Array of Molecularly Mediated Thin Film Assemblies of Nanoparticles: Correlation of Vapor Sensing with Interparticle Spatial Properties

The ability to tune interparticle spatial properties of nanoparticle assemblies is essential for the design of sensing materials toward desired sensitivity and selectivity. This paper reports findings of an investigation of molecularly mediated thin film assemblies of metal nanoparticles with controllable interparticle spatial properties as a sensing array. The interparticle spatial properties are controlled by a combination of alpha,omega-difunctional alkyl mediators (X-(CH(2))(n)-X) such as alkyl dithiols, dicarboxylate acids, and alkanethiol shells capped on nanoparticles. Alkanethiolate-capped gold and gold-silver alloy nanoparticles (2-3 nm) were studied as model building blocks toward the thin film assemblies, whereas the variation of alkyl chain length manipulates the interparticle spacing. The thin films assembled on an interdigitated microelectrode array platform are characterized for determining their responses to the sorption of volatile organic compounds (VOCs). The correlation between the response sensitivity and the interparticle spacing properties revealed not only a clear dependence of the sensitivity on alkyl chain length but also the occurrence of a dramatic change of the sensitivity in a region of chain length for the alkyl mediator comparable with that of the capping alkyl chains. This finding reflects a balance between the interparticle chain-chain cohesive interdigitation and the nanostructure-vapor interaction which determines the relative change of the electrical conductivity of the inked nanoparticle thin film in response to vapor sorption. The results, along with statistical analysis of the sensor array data in terms of sensitivity and selectivity, have provided important insights into the detailed delineation between the interparticle spacing and the nanostructured sensing properties.

Ozone- and thermally activated films of palladium monolayer-protected clusters for chemiresistive hydrogen sensing

Here we describe the chemiresistive H2-sensing properties of drop-cast films comprised of 3.0 nm average diameter hexanethiolate-coated Pd monolayer-protected clusters (C6 Pd MPCs) bridging a pair of electrodes separated by a 23 microm gap. The gas-sensing properties were measured for 9.6-0.11% H2 in a H2/N2 mixture. The sensing mechanism is based on changes in the resistance of the film upon reaction of Pd with H2 to form PdH(x), which is known to be larger in volume and more resistive than pure Pd. As-prepared Pd MPC films are highly insensitive to H2, requiring O3 and thermal treatment to enhance changes in film resistance in the presence of H2. Exposure to O3 for 15 min followed by activation in 100% H2 leads to an increase in film conductivity in the presence of H2, with a detection limit of 0.11% H2. When exposed to temperatures of 180-200 degrees C, the conductivity of the film increases and a decrease in conductivity occurs in the presence of H2 with a detection limit of 0.21%. The sensing behavior reverses after further heating to 260 degrees C, exhibiting an increase in conductivity in the presence of H2 as in O3-treated films and a detection limit of 0.11%. The sensitivity of the variously treated films follows the order O3 > high temp > low temp, and the response times at 1.0% H2 range from 10 to 50s, depending on the treatment. FTIR spectroscopy, Raman spectroscopy, and atomic force microscopy provide information about the C6 monolayer, Pd metal, and film morphology, respectively, as a function of O3 and heat treatment to aid in understanding the observed sensing behavior. This work demonstrates a simple chemical approach toward fabricating a fast, reversible sensor capable of detecting low concentrations of H2.

Dielectric Medium Effects on Collective Surface Plasmon Coupling Interactions in Oligothiophene-Linked Gold Nanoparticles

The near-field coupling interactions between surface plasmon modes of neighboring metal nanoparticles (NPs) are investigated in thin films of oligothiophene-linked Au NPs. The oligothiophene linker facilitates near-field coupling between adjacent NPs, and disruption of the conjugation in the oligothiophene by chemical oxidation leads to a decrease in surface plasmon resonance (SPR) coupling between neighboring particles. The SPR coupling between NPs was found to be highly dependent on the dielectric constant of the medium that the films are exposed to, where a higher dielectric medium leads to weaker coupling. The dependence of the SPR coupling on the dielectric constant of the medium is explained using electrodynamic theory.

Effects of organic ligands, electrostatic and magnetic interactions in formation of colloidal and interfacial inorganic nanostructures

This paper discusses effects of organic ligands, electrostatic and magnetic interactions involved in morphological control of chemically synthesized inorganic nanostructures including colloid and planar systems. The special attention was concentrated on noble metal (gold and palladium) nanoparticles and nanostructures formed at the gas-liquid interface. The analysis of experimental data showed that electrostatic and ligand-related interactions influence very strongly on the metal nanostructure morphology. The hydrophobicity of ligand, charge and binding affinity to inorganic phase are important factors influencing the morphology of inorganic nanostructures formed in a layer at the gas/liquid interface by the interfacial synthesis method. The important point of this method is the quasi two-dimensional character of reaction area and possibilities to realize ultimately thin and anisotropic dynamic monomolecular reaction system with two-dimensional diffusion and interactions of precursors, intermediates and ligands resulting in planar growth and organization of inorganic nanoparticles and nanostructures in the plain of Langmuir monolayer. The morphology of resulting inorganic nanostructures can be controlled efficiently by variations of growth conditions via changes in state and composition of interfacial planar reaction media with the same precursor, and by variations of composition of adjacent bulk phases. The extreme anisotropy and heterogeneity of two-dimensional interfacial reaction system allows creating conditions when growing inorganic particles floating on the aqueous phase surface interact selectively with hydrophobic water-insoluble ligands in interfacial monolayer or with hydrophilic bulk-phase ligands, or at the same time with ligands of different nature present in monolayer and in aqueous phase. The spatial anisotropy of interfacial reaction system and non-homogeneity of ligand binding to inorganic phase gives possibilities for growth of integrated anisotropic nanostructures with unique morphologies, in particularly those characterized by very high surface/volume ratio, high effective perimeter, and labyrinth-like structure. In a case of magnetic nanoparticles dispersed in colloids specific magnetic dipolar interactions can result in formation of chains, rings and more complex nanoparticulate structures or separated highly anisotropic nanoparticles. Theoretical considerations indicate to the importance of system dimensionality in relation to the energy balance which determines specific features of structure organization in planar charged metallic and magnetic nanostructures. For example, a requirement of Coulomb energy minimum, the possibility of free electron redistribution and strengthened attractive interactions between particles in metallic nanostructures can explain formation of very branchy systems with extremely high "effective perimeter". The obtained experimental and literature data show that system dimensionality, organic ligand nature along with electrostatic and magnetic interactions are most important factors of morphological control of chemically synthesized inorganic nanomaterials. The understanding and appropriate exploitation of these factors can be useful for further developments of efficient nanofabrication techniques based on colloidal and interfacial synthetic methods.

Chemiresistive Vapor Sensing with Microscale Films of Gold Monolayer Protected Clusters

Here we report the stability, conductivity, and vapor-sensing properties of microcontact-printed films of 1.6-nm average diameter hexanethiolate-coated gold monolayer protected clusters (C6 Au MPCs). The C6 Au MPCs were stamped into parallel lines (approximately 1.2 microm wide and 400 nm thick) across two Au electrodes separated by a 1-microm gap. The chemiresistive vapor-sensing properties were measured for saturated toluene and 2-propanol vapors. As-prepared patterned Au MPC films were unstable in the presence of saturated toluene vapor, and their current response was irreversible. Chemically linking the films with vapor-phase hexanedithiol greatly improves their stability and leads to reversible responses. The extent of Au MPC cross-linking and vapor response to organic vapors varies with different exposure times to dithiol vapor. The response to toluene changed from 61 to 8% for exposures of 1 and 60 min, respectively, which is likely due to greater film flexibility with less dithiol exposure. The current measured through the films varies from 10(-11) to 10(-3) Angstroms as a function of the temperature between 250 and 320 degrees C, which correlates with the loss of organic material as measured by FT-IR spectroscopy and the change in thickness and width of the film as measured by atomic force microscopy. The vapor-sensing properties vary with temperature, current, and organic content in the film, which are all interrelated. Response to toluene decreased with increasing temperature and conductivity, while the response to 2-propanol was less predictable. Reducing the size of vapor-sensing devices based on Au MPCs is important for creating highly portable devices that can simultaneously detect multiple analytes. This work demonstrates a simple method for reducing the size of such devices down to the microscale and describes methods for maximizing response, stability, and reversibility.

Preparation and characterization of aqueous colloids of Pt–Ru nanoparticles

A synthetic method for platinum-ruthenium (PtRu) nanoparticles in aqueous media is proposed. This method employs citric acid as a capping agent and NaBH(4) as a reducing agent with the aid of pH control. The number-averaged size of the PtRu nanoparticles was ca. 2 nm. The crystal phase and chemical composition of the nanoparticles was investigated by X-ray diffraction measurement and scanning transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy analysis, which indicated that the nanoparticles mainly consisted of an alloy of Pt and Ru. Electrochemical measurement showed that the PtRu nanoparticles had catalytic activity for methanol oxidation.

Electron Hopping Dynamics in Monolayer-Protected Au Cluster Network Polymer Films by Rotated Disk Electrode Voltammetry

Electrons are transported within polymeric films of alkanethiolate monolayer-protected Au clusters (MPCs) by electron hopping (self-exchange) between the metal cores. The surrounding monolayers, the molecular linkers that generate the network polymer film, or both, presumably serve as tunneling bridges in the electron transfers. This paper introduces a steady-state electrochemical method for measuring electron hopping rates in solvent-wetted and swollen, ionically conductive MPC films. The films are network polymer films of nanoparticles, coated on a rotated disk electrode that is contacted by a solution of a redox species (decamethylferrocene, CpFe). Controlling the electrode potential such that the film mediates oxidation of the redox probe can force control of the overall current onto the rate of electron hopping within the film, which is characterized as the apparent electron diffusion coefficient D(E). D(E) is translated into an apparent electron hopping rate k(ET) by a cubic lattice model. The experiment is applied to MPC network polymer films linked by alpha,omega-alkanedithiolates and by metal ion-carboxylate connections. We evaluate the dependencies of apparent hopping rate on CpFe concentration, film thickness, electrode potential relative to the CpFe formal potential, film-swelling solvent, and temperature. The apparent hopping rates are in the 10(4)-10(5) s(-)(1) range, which is slower than those for the same kind of MPC films, but in a dry (nonswollen) state measured by electronic conductivities.