High-mass-loading cobalt iron phosphide@nickel vanadium layered double hydroxide heterogeneous nanosheet arrays for hybrid supercapacitors

Designing multidimensional heterostructures on flexible substrates is an efficient approach to resolve the low energy density of supercapacitors. Herein, a three-dimensional (3D) porous cobalt iron phosphide (CoFeP)@nickel vanadium-layered double hydroxide (NiV-LDH) heterostructure has been prepared anchored on carbon cloth (CC) substrate. In this nanoarchitecture, NiV-LDH nanosheets are densely wrapped on the surface of CoFeP nanosheets, which forms a hierarchically porous framework with an enlarged surface area and accessible pore channels. Benefiting from the strong interaction and synergistic effect between CoFeP and NiV-LDH, the well-defined heterostructure can realize simultaneously rich redox active sites, rapid reaction dynamics, and good structural stability. Thus, the binder-free CoFeP@NiV-LDH electrode with a high mass loading of 6.47 mg cm-2 displays a significantly increased specific capacity of 903.1C g-1 (2.35C cm-2) at 1 A g-1 and enhanced rate capability when compared to pristine CoFeP and NiV-LDH. Additionally, the assembled hybrid supercapacitor (HSC) yields an energy density of 77.9 Wh kg-1/0.98 Wh cm-2 and excellent long-term stability. This research proposes a rational route for designing heterogeneous micro-/nanoarchitectures with commercial-level mass loading for the practical application of high-energy-density supercapacitors.

A Review of Transition Metal Boride, Carbide, Pnictide, and Chalcogenide Water Oxidation Electrocatalysts

Transition metal borides, carbides, pnictides, and chalcogenides (X-ides) have emerged as a class of materials for the oxygen evolution reaction (OER). Because of their high earth abundance, electrical conductivity, and OER performance, these electrocatalysts have the potential to enable the practical application of green energy conversion and storage. Under OER potentials, X-ide electrocatalysts demonstrate various degrees of oxidation resistance due to their differences in chemical composition, crystal structure, and morphology. Depending on their resistance to oxidation, these catalysts will fall into one of three post-OER electrocatalyst categories: fully oxidized oxide/(oxy)hydroxide material, partially oxidized core@shell structure, and unoxidized material. In the past ten years (from 2013 to 2022), over 890 peer-reviewed research papers have focused on X-ide OER electrocatalysts. Previous review papers have provided limited conclusions and have omitted the significance of "catalytically active sites/species/phases" in X-ide OER electrocatalysts. In this review, a comprehensive summary of (i) experimental parameters (e.g., substrates, electrocatalyst loading amounts, geometric overpotentials, Tafel slopes, etc.) and (ii) electrochemical stability tests and post-analyses in X-ide OER electrocatalyst publications from 2013 to 2022 is provided. Both mono and polyanion X-ides are discussed and classified with respect to their material transformation during the OER. Special analytical techniques employed to study X-ide reconstruction are also evaluated. Additionally, future challenges and questions yet to be answered are provided in each section. This review aims to provide researchers with a toolkit to approach X-ide OER electrocatalyst research and to showcase necessary avenues for future investigation.

High-Performance Electrocatalytic Reduction of Nitrite to Ammonia under Ambient Conditions on a FeP@TiO2 Nanoribbon Array

Electrochemical nitrite (NO2-) reduction is recognized as a promising strategy for synthesizing valuable ammonia (NH3) and degrading NO2- pollutants in wastewater. The six-electron process for the NO2- reduction reaction is complex and necessitates a highly selective and stable electrocatalyst for efficient conversion of NO2- to NH3. Herein, a FeP nanoparticle-decorated TiO2 nanoribbon array on a titanium plate (FeP@TiO2/TP) is proposed as an efficient catalyst for NH3 production under ambient conditions. In 0.1 M NaOH with 0.1 M NO2-, such a FeP@TiO2/TP affords a large NH3 yield of 346.6 μmol h-1 cm-2 and a high Faradaic efficiency of 97.1%. Additionally, it demonstrates excellent stability and durability during long-term cycling tests and electrolysis experiments.

Unveiling the Metal Incorporation Effect of Steady-Active FeP Hydrogen Evolution Nanocatalysts for Water Electrolyzer

Metal phosphides are promising noble metal-free electrocatalysts for hydrogen evolution reaction (HER), but they usually suffer from inferior stability and thus are far from the device applications. We reported a facile and controllable synthetic method to prepare metal-incorporated M-FeP nanoparticles (M=Cr, Mn, Co, Fe, Ni, Cu, and Mo) with the guide of the density functional theory (DFT). The evaluated HER activity sequence was consistent with the DFT predictions, and cobalt was revealed to be the appropriate dopant. With the optimization of the Co/Fe ratio, the Fe_0.67 Co_0.33 P/C only required overpotentials of 67 mV and 129 mV to obtain the cathodic current density of 10 and 100 mA cm^-2, respectively. It maintained the initial activity in the 10 h stability test, surpassing the other Co-FeP/C catalysts. Ex situ experiments demonstrated that the decreased element leaching and the increased surface phosphide content contributed to the high stability of the Fe_0.67 Co_0.33 P/C. A proton exchange membrane water electrolyzer was assembled using the Fe_0.67 Co_0.33 P/C as the cathodic catalyst. It showed a current density of 0.8 A cm^-2 at the applied voltage of 2.0 V and retained the initial activity in the 1000 cycles' stability test, suggesting the potential application of the catalysts.

Efficient Hydrogen and Oxygen Evolution Catalysis Using 3D-Structured Nickel Phosphosulfide Nanosheets in Alkaline Media

Water electrolysis offers a zero-carbon route to generate renewable energy conversion systems. Herein, a self-supported nickel phosphosulfide nanosheet (NS) electrocatalyst was fabricated at a low temperature on carbon cloth, which was then subjected to Ar etching to enhance its catalytic activity. Etching resulted in better hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) performance than other samples, with overpotentials of 103.1 mV (at 10 mA cm^-2) and 278.9 mV (at 50 mA cm^-2), respectively. The characterization results confirmed that Ar etching created a thin amorphous layer around the NiPS₃ NSs, which increased the number of active sites and modulated their electronic structures. These 3D-structured NiPS₃ NSs and their subsequent Ar etching process show promise for applications in overall water splitting in alkaline media.

Construction of N, P Co-Doped Carbon Frames Anchored with Fe Single Atoms and Fe2 P Nanoparticles as a Robust Coupling Catalyst for Electrocatalytic Oxygen Reduction

A coupling catalyst of highly dispersed N, P co-doped carbon frames (NPCFs) anchored with Fe single atoms (SAs) and Fe₂ P nanoparticles (NPs) is synthesized by a novel in situ doping-adsorption-phosphatization strategy for the electrocatalytic oxygen reduction reaction (ORR). The optimized Fe SAs-Fe₂ P NPs/NPCFs-2.5 catalyst shows a superior ORR activity and stability in 0.5 m H₂ SO₄ and 0.1 m KOH, respectively. Theoretical calculations reveal a synergistic effect, in that the existence of Fe₂ P weakens the adsorption of ORR intermediates on active sites and lowers the reaction free energy. The doped P atoms with a strong electron-donating ability elevate the energy level of Fe-3d orbitals and facilitate the adsorption of O₂ . The active Fe atoms exist in a low oxidation state and are less positively charged, and they serve as an electron reservoir capable of donating and releasing electrons, thus improving the ORR activity. Operando and in situ characterization results indicate that the atomically dispersed FeN₄ /FeP coupled active centers in the Fe SAs-Fe₂ P NPs/NPCFs-2.5 catalyst are characteristic of the different catalytic mechanisms in acidic and alkaline media. This work proposes a novel idea for constructing coupling catalysts with atomic-level precision and provides a strong reference for the development of high-efficiency ORR electrocatalysts for practical application.

Water electrolysis: from textbook knowledge to the latest scientific strategies and industrial developments

Replacing fossil fuels with energy sources and carriers that are sustainable, environmentally benign, and affordable is amongst the most pressing challenges for future socio-economic development. To that goal, hydrogen is presumed to be the most promising energy carrier. Electrocatalytic water splitting, if driven by green electricity, would provide hydrogen with minimal CO2 footprint. The viability of water electrolysis still hinges on the availability of durable earth-abundant electrocatalyst materials and the overall process efficiency. This review spans from the fundamentals of electrocatalytically initiated water splitting to the very latest scientific findings from university and institutional research, also covering specifications and special features of the current industrial processes and those processes currently being tested in large-scale applications. Recently developed strategies are described for the optimisation and discovery of active and durable materials for electrodes that ever-increasingly harness first-principles calculations and machine learning. In addition, a technoeconomic analysis of water electrolysis is included that allows an assessment of the extent to which a large-scale implementation of water splitting can help to combat climate change. This review article is intended to cross-pollinate and strengthen efforts from fundamental understanding to technical implementation and to improve the 'junctions' between the field's physical chemists, materials scientists and engineers, as well as stimulate much-needed exchange among these groups on challenges encountered in the different domains.

First principles study of optoelectronic and photocatalytic performance of novel transition metal dipnictide XP2 (X = Ti, Zr, Hf) monolayers

Low cost and highly efficient two dimensional materials as photocatalysts are gaining much attention to utilize solar energy for water splitting and produce hydrogen fuel as an alternative to deal with the energy crisis and reduce environmental hazards. First principles calculations are performed to investigate the electronic, optical and photocatalytic properties of novel two dimensional transition metal dipnictide XP₂ (X = Ti, Zr, Hf) monolayers. The studied single layer XP₂ is found to be dynamically and thermally stable. TiP₂, ZrP₂ and HfP₂ systems exhibit semiconducting nature with moderate indirect band gap values of 1.72 eV, 1.43 eV and 2.02 eV, respectively. The solar light absorption is found to be in energy range of 1.65–3.3 eV. All three XP₂ systems (at pH = 7) and the HfP₂ monolayer (at pH = 0) that straddle the redox potentials, are promising candidates for the water splitting reaction. These findings enrich the two dimensional family and provide a platform to design novel devices for emerging optoelectronic and photovoltaic applications.

Low cost and highly efficient two dimensional materials as photocatalysts are gaining much attention to utilize solar energy for water splitting and produce hydrogen fuel as an alternative to deal with the energy crisis and reduce environmental hazards.

Effect of cobalt phosphide (CoP) vacancies on its hydrogen evolution activity via water splitting: a theoretical study

Defect engineering plays an important role in improving the performance of catalysts. To clarify the roles of Co and P vacancies in CoP for water splitting, a theoretical study based on density functional theory was carried out in this paper. The geometric and electronic structures, activity and stability of the CoP (101)B surface, CoP (101)B with the Co vacancy (Co_vac) and the P vacancy (P_vac) are investigated. The results indicate that the CoP (101)B surface with P_vac and Co_vac can enhance the electron transfer to the surface. The P_vac will upward shift the Co d-band center near the vacancy site, which promotes the adsorption of H on the Co atom. As a result, the bridge Co-Co sites near the vacancy become the active sites for the hydrogen evolution reaction (HER) (ΔG_H* = 0.01 eV). The loss of the Co atom also results in an upward shift of its d-band center, which will enhance the H adsorption on the adjacent Co sites. The unevenly distributed electrons due to the presence of vacancies on the surface cause spontaneous dissociation of H₂O molecules. Furthermore, the thermodynamic analysis and surface energy find that the CoP (101)B and (101)B facets with Co_vac and P_vac present good stability. The current work has shed light onto the mechanism of water splitting on the surface of phosphide with vacancies. Our study suggests that engineering vacancies on CoP is a feasible route to improve its catalytic activity.

Insights into the Effect of Precursors on the FeP-Catalyzed Hydrogen Evolution Reaction

Iron phosphide nanoparticles (NPs) are promising noble metal-free electrocatalysts for the hydrogen evolution reaction (HER), but they usually show inferior activity due to the limited surface area and oxidative passivation. We reported a facile synthetic method to prepare FeP hollow NPs (HNPs) with various precursors. It was proven that the structural parameters (i.e., size, phosphating temperature, phase, and surfactant) of oxide precursors were correlated to the electrochemically active surface area (ECSA), phase purity, surface oxidation, and hollow morphology of FeP HER catalysts, thus affecting the HER activity. Among the three FeP HNPs, the 9 nm FeP HNPs prepared using the Fe₃O₄ precursor exhibited the highest overall activity with the lowest overpotential of 76 mV to drive a cathodic current density of 10 mA·cm^-2 due to the highest ECSA, while 25 nm FeP prepared using the Fe₂O₃ precursor showed the highest turnover frequency because of the high phase purity and low surface oxidation degree.

Janus Mo2P3 Monolayer as an Electrocatalyst for Hydrogen Evolution

The rational design of low-cost electrocatalysts with the desired performance is the core of the large-scale hydrogen production from water. Two-dimensional materials with high specific surface area and excellent electron properties are ideal candidates for electrocatalytic water splitting. Herein, we identify a hitherto unknown Mo₂P₃ monolayer with a Janus structure (i.e., out-of-plane asymmetry) through first-principle structure search calculations. Its inherent metallicity ensures good electrical conductivity. Notably, its catalytic activity is comparable to that of Pt and the density of active sites is up to 2.65 × 10¹⁵ site/cm² owing to the Mo → P charge transfer enhancing the catalytic activity of P atoms and asymmetric structure exposing more active sites to the surface. The Mo₂P₃ monolayer can spontaneously produce hydrogen through the Volmer-Heyrovsky pathway. These excellent performances can be well maintained under strain. The coexistence of covalent and ionic bonds results in Mo₂P₃ having high stability. All these excellent properties make the Mo₂P₃ monolayer a promising candidate for electrocatalytic water splitting.

Highly active Ni/Fe3O4/TiO2 nanocatalysts with tunable interfacial interactions for PH3 decomposition

The mixed-metal oxide Ni/Fe₃O₄/TiO₂ with two metal-oxide interfaces to catalyze sequential chemical reactions was first applied in the decomposition of phosphine gas for yellow phosphorus (P₄) production. The catalyst was prepared with tunable Ni-Fe₃O₄ and Ni-TiO₂ interactions via annealing and subsequent reduction. Ni/Fe₃O₄/TiO₂ exhibited significantly effective activity and good stability in the PH₃ decomposition, which were achieved by modulating the metal-support interaction. The characterizations by scanning electron microscopy(SEM), X-ray diffraction analysis(XRD), BET surface area measurement and X-ray photoelectron spectroscopy(XPS) were carried out. The enhancements of the Ni-Fe₃O₄ and Ni-TiO₂ dual interactions by annealing and reduction were verified and the mechanism of PH₃ decomposition over the modulated Ni/Fe₃O₄/TiO₂ catalyst was investigated. NiOOH as an active catalytic intermediate species is produced by the synergistic catalytical dual interfaces. The catalytic reaction pathways of PH₃ decomposition by the dual interfaces were firstly revealed. The results provide underlying insights in the way to promote the catalytic performance for synergistic catalysis in PH₃ decomposition.

Active Site Engineering in CoP@NC/Graphene Heterostructures Enabling Enhanced Hydrogen Evolution

As the core of an electrocatalyst, the active site is critical to determine its catalytic performance in the hydrogen evolution reaction (HER). In this work, porous N-doped carbon-encapsulated CoP nanoparticles on both sides of graphene (CoP@NC/GR) are derived from a bimetallic metal-organic framework (MOF)@graphene oxide composite. Through active site engineering by tailoring the environment around CoP and engineering the structure, the HER activity of CoP@NC/GR heterostructures is significantly enhanced. Both X-ray photoelectron spectroscopy (XPS) results and density functional theory (DFT) calculations manifest that the electronic structure of CoP can be modulated by the carbon matrix of NC/GR, resulting in electron redistribution and a reduction in the adsorption energy of hydrogen (ΔG_H*) from -0.53 to 0.04 eV. By engineering the sandwich-like structure, active sites in CoP@NC/GR are further increased by optimizing the Zn/Co ratio in the bimetallic MOF. Benefiting from this active site engineering, the CoP@NC/GR electrocatalyst exhibits small overpotentials of 105 mV in 0.5 M H₂SO₄ (or 125 mV in 1 M KOH) to 10 mA cm^-2, accelerated HER kinetics with a low Tafel slope of 47.5 mV dec^-1, and remarkable structural and HER stability.

Construction of a Unique Structure of Ru Sites in the RuP Structure for Propane Dehydrogenation

It is an important task to develop low-cost and anticoking catalysts for the propane dehydrogenation (PDH) reaction. In this work, the P element is introduced to the Ru-based catalyst to obtain Ru sites with a unique structure and the obtained Ru_xP_y (x/y = 2:1, 1:1, 1:2) catalysts are then employed in PDH. Density functional theory (DFT) results show that the addition of P leads to the formation of separated Ru sites and the adjustment of the valance band state of Ru. The upward shift of the d-band center leads to a reduction of the reaction energy barrier for dehydrogenation of propane and an enhancement of catalytic activity. The analysis of the competition between propylene deep dehydrogenation and propylene desorption for each catalyst shows that desorption of propylene is preferred on the RuP(112) surface. Considering both catalytic activity and propylene selectivity, the RuP catalyst is potential for the propane dehydrogenation reaction. On the RuP surface, the PDH reaction proceeds by the dehydrogenation of the H atom on the methylene group (isopropyl pathway), thus restraining the deep dehydrogenation of propylene. The Ru_xP_y catalysts are also synthesized in experiments, and PDH evaluation shows that the RuP structure is a remarkable PDH catalyst with a stable structure, anticoking ability, and low cost.

Enhancing the efficiency of the hydrogen evolution reaction utilising Fe3P bulk modified screen-printed electrodes via the application of a magnetic field

We report the fabrication and optimisation of Fe3P bulk modified screen-printed electrochemical platforms (SPEs) for the hydrogen evolution reaction (HER) within acidic media. We optimise the achievable current density towards the HER of the Fe3P SPEs by utilising ball-milled Fe3P variants and increasing the mass percentage of Fe3P incorporated into the SPEs. Additionally, the synergy of the application of a variable weak (constant) external magnetic field (330 mT to 40 mT) beneficially augments the current density output by 56%. This paper not only highlights the benefits of physical catalyst optimisation but also demonstrates a methodology to further enhance the cathodic efficiency of the HER with the facile application of a weak (constant) magnetic field.

Phase-dependent electrocatalytic activity of colloidally synthesized WP and α-WP2 electrocatalysts for hydrogen evolution reaction

Transition metal phosphides (TMPs) have emerged as efficient non-noble electrocatalysts for hydrogen evolution reaction (HER).

Highly Crystalline Hollow Toroidal Copper Phosphosulfide via Anion Exchange: A Versatile Cation Exchange Nanoplatform

Postmodification of nanocrystals through cation exchange has been very successful in diversifying nanomaterial compositions while retaining the structural motif. Copper compound nanoparticles are particularly useful as templates because of inherent defects serving as effective cation diffusion routes and excellent cation mobility. Therefore, the development of shape-controlled multianion systems, such as copper phosphosulfide, can potentially lead to the formation of diverse metal phosphosulfide nanomaterials that have otherwise inaccessible compositions and structures. However, there is, to the best of our knowledge, no report on the shape-controlled synthesis of copper phosphosulfide nanoparticles because the introduction of the second anion to the metal compound might destroy the nanoparticle morphology and crystallinity due to the required high energy for anion diffusion and mixing. Herein, we report that it is feasible to transfer the structural motif of copper sulfide to copper phosphosulfide using tris(diethylamino)phosphine. The anion-mixed copper phosphosulfide in the form of a hollow toroid could provide a pathway to previously inaccessible phases and morphologies. We verified the versatility of a copper phosphosulfide hollow toroid as a cation-exchange template by the successful synthesis of cobalt, nickel, indium, and cadmium phosphosulfides as well as bimetallic cobalt-nickel phosphosulfide (Co_2-xNi_xP_1-yS_y) with a retained structural motif.

The in situ preparation of iron phosphide using ionic liquids as iron and phosphorus sources for efficient hydrogen evolution reactions

Ionic liquids (ILs) were utilized as iron and phosphorus sources for the preparation of iron phosphide for the first time. The IL trihexyl(tetradecyl)phosphonium tetrachloroferrate ([P(C₆H₁₃)₃C₁₄H₂₉][FeCl₄]) and carbon nanotubes (CNTs) were applied as precursors for the in situ preparation of Fe₂P_(IL6)/CNTs. This material has good catalytic activity and stability for the hydrogen evolution reaction, including a low onset overpotential (75 mV) and Tafel slope (68 mV dec^-1). Moreover, this catalyst exhibits current densities of 10 and 20 mA cm^-2 at overpotentials of 115 and 150 mV, respectively. The phosphidation process using [P(C₆H₁₃)₃C₁₄H₂₉][FeCl₄] was also investigated. All experimental results indicate that Fe₂P can be formed in situ on the CNTs using this IL, and that the CNTs help the formation of the Fe₂P nanoparticles and improve the electrical conductivity. This IL-based in situ preparation strategy is facile and environmentally friendly and does not require the addition of other reagents. This method holds great promise for application in other electrochemical studies.

Cobalt-based heterogeneous catalysts in an electrolyzer system for sustainable energy storage

Nowadays, the production of hydrogen and oxygen focuses on renewable energy techniques and sustainable energy storage. A substantial challenge is to extend low-cost electrocatalysts consisting of earth-abundant resources, prepared by straightforward approaches that display high intrinsic activity compared to noble metals. The expansion of bifunctional catalysts in alkaline electrolytes for both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) has become very crucial in recent times. Herein, the recent progress in cobalt-based HER-OER electrocatalysts has been are brushed up and numerous bifunctional cobalt-based catalysts such as cobalt-oxides, phosphides, sulfides, selenides, nitrides, borides, carbides, perovskites, and MOF-based cobalt analogs have been investigated in detail. Specifically, much more attention has been paid to their structural variation, bifunctional activity, overpotential of the overall system, and stability. Cobalt-based catalysts with lower cell voltage, remarkable durability, and unique electronic structures, offer a new perspective in energy-related fields. In recent years, cobalt-based analogs with diagnostic facilities have been introduced due to their electronic structures, tunable d band structures, and tailorable active sites. This perspective also elucidates the present issues, promising ideas, and future forecasts for cobalt-based catalysts. The critical aspects of cobalt-based catalysts and the numerous opportunities, as discussed at the end, can possibly enrich the sustainable energy field.

Three-Dimensional Transition Metal Phosphide Heteronanorods for Efficient Overall Water Splitting

The development of low-cost electrocatalysts with excellent activity and durability for both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER) poses a huge challenge in water splitting. In this study, a simple and scalable strategy is proposed to fabricate 3 D heteronanorods on nickel foam, in which nickel molybdenum phosphide nanorods are covered with cobalt iron phosphide (P-NM-CF HNRs). As a result of the rational design, the P-NM-CF HNRs have a large surface area, tightly connected interfaces, optimized electronic structures, and synergy between the metal atoms. Accordingly, the P-NM-CF HNRs exhibit a remarkably high catalytic activity for the OER under alkaline conditions and wide-pH HER. For overall water splitting, the catalyst only requires a voltage of 1.53 V to reach a current density of 10 mA cm^-2 in 1 m KOH with prominent stability, and the activity is not degraded after stability testing for 36 h. This new strategy can inspire the design of durable nonprecious-metal catalysts for large-scale industrial water splitting.

Novel electronic properties of monoclinic MP4 (M = Cr, Mo, W) compounds with or without topological nodal line

Transition metal phosphides hold novel metallic, semimetallic, and semiconducting behaviors. Here we report by ab initio calculations a systematical study on the structural and electronic properties of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\hbox {MP}_4$$\end{document}MP4 (M = Cr, Mo, W) phosphides in monoclinic C2/c (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{2h}^6$$\end{document}C2h6) symmetry. Their dynamical stabilities have been confirmed by phonon modes calculations. Detailed analysis of the electronic band structures and density of states reveal that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\hbox {CrP}_4$$\end{document}CrP4 is a semiconductor with an indirect band gap of 0.47 eV in association with the p orbital of P atoms, while \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\hbox {MoP}_4$$\end{document}MoP4 is a Dirac semimetal with an isolated nodal point at the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Gamma$$\end{document}Γ point and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\hbox {WP}_4$$\end{document}WP4 is a topological nodal line semimetal with a closed nodal ring inside the first Brillouin zone relative to the d orbital of Mo and W atoms, respectively. Comparison of the phosphides with group VB, VIB and VIIB transition metals shows a trend of change from metallic to semiconducting behavior from \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\hbox {VB-MP}_4$$\end{document}VB-MP4 to VIIB-\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\hbox {MP}_4$$\end{document}MP4 compounds. These results provide a systematical understandings on the distinct electronic properties of these compounds.

Crystalline Copper Selenide as a Reliable Non-Noble Electro(pre)catalyst for Overall Water Splitting

Electrochemical water splitting remains a frontier research topic in the quest to develop artificial photosynthetic systems by using noble metal-free and sustainable catalysts. Herein, a highly crystalline CuSe has been employed as active electrodes for overall water splitting (OWS) in alkaline media. The pure-phase klockmannite CuSe deposited on highly conducting nickel foam (NF) electrodes by electrophoretic deposition (EPD) displayed an overpotential of merely 297 mV for the reaction of oxygen evolution (OER) at a current density of 10 mA cm-2 whereas an overpotential of 162 mV was attained for the hydrogen evolution reaction (HER) at the same current density, superseding the Cu-based as well as the state-of-the-art RuO2 and IrO2 catalysts. The bifunctional behavior of the catalyst has successfully been utilized to fabricate an overall water-splitting device, which exhibits a low cell voltage (1.68 V) with long-term stability. Post-catalytic analyses of the catalyst by ex-situ microscopic, spectroscopic, and analytical methods confirm that under both OER and HER conditions, the crystalline and conductive CuSe behaves as an electro(pre)catalyst forming a highly reactive in situ crystalline Cu(OH)2 overlayer (electro(post)catalyst), which facilitates oxygen (O2 ) evolution, and an amorphous Cu(OH)2 /CuOx active surface for hydrogen (H2 ) evolution. The present study demonstrates a distinct approach to produce highly active copper-based catalysts starting from copper chalcogenides and could be used as a basis to enhance the performance in durable bifunctional overall water splitting.

Multi-channel V-doped CoP hollow nanofibers as high-performance hydrogen evolution reaction electrocatalysts

Rational design and construction of high-efficiency and low-cost non-noble metal-based electrocatalysts for the hydrogen evolution reaction (HER) is critical for future renewable energy systems. Herein, a multi-channel V-doped CoP (MC-V-CoP) hollow nanofiber is fabricated via electrospinning and a subsequent oxidation/phosphorization process. The formation of a multi-channel hollow structure and V doping can enlarge the exposure of active sites, facilitate the electron transfer and tune the electronic structure of the active sites, resulting in the enhancement of the HER performance. As a result, the MC-V-CoP hollow nanofiber exhibits excellent HER activity with a low overpotential of 65 and 189 mV at 10 and 300 mA cm-2 in alkaline medium, respectively. This is superior to the commercial 20 wt% Pt/C catalyst at a high current density (212 mV at 300 mA cm-2), manifesting its outstanding performance toward the HER at a high current density. In addition, the MC-V-CoP hollow nanofiber also exhibits outstanding HER activity in neutral medium. The proposed strategy for fabricating multi-channel hollow nanofibers can also be used to prepare other transition metal phosphides for advanced electrochemical applications.

Improving Electrochemical Hydrogen Evolution of Ag@CN Nanocomposites by Synergistic Effects with α-Rich Proteins

A graphitic carbon nitride nanostructure has been successfully functionalized by incorporation of different silver contents and subsequent modification with an α-rich protein, namely hemoglobin. Mechanochemistry has been employed, as an efficient and sustainable procedure, for the incorporation of the protein. A complete characterization analysis has been performed following a multitechnique approach. Particularly, XPS data exhibited considerable differences in the C 1s region for the Hb/xAg@CN, ensuring the successful protein anchorage on the surface of the graphitic carbon nitride-based materials. The as-synthesized nanomaterials delivered impressive performance toward hydrogen evolution reactions with an overpotential of 79 mV at a current density of 10 mA/cm² for Hb/20Ag@CN nanohybrids, which is comparable with the most efficient HER electrocatalysts reported in the literature. The outstanding HER properties were associated with the unique synergistic interactions, quantitatively measured, between AgNPs, Hb tertiary architecture, and the graphitic carbon nitride networks.

Double Metal Diphosphide Pair Nanocages Coupled with P-Doped Carbon for Accelerated Oxygen and Hydrogen Evolution Kinetics

Developing efficient and durable bifunctional transition metal phosphide (TMP) electrocatalysts is still a great challenge because of its relatively sluggish kinetics of oxygen evolution reaction (OER). Herein, we report a unique bimetallic diphosphide pair (FeP₂-NiP₂) forming spherical nanocages encapsulated in P-doped carbon layers (FeP₂-NiP₂@PC) as advanced bifunctional electrocatalyst synthesized by a very facile phosphorization approach. The obtained FeP₂-NiP₂@PC electrocatalyst exhibits an outstanding OER activity with an ultralow overpotential of 248 mV in 1 M KOH and a low overpotential of 117 mV for HER in 0.5 M H₂SO₄ (@10 mA·cm^-2). Also it gives an exceptional long-term durability toward OER (60 h) and HER (20 h). Differently from the electrocatalysts as reported, after successive 3000 cycles CV acceleration, its overpotential decreases about 10 mV. Further investigation unveils that the electrochemical activation process boosts in situ phase transformation of oxides and phosphides to oxyhydroxides as the vital intermediates in FeP₂-NiP₂@PC during OER electrocatalysis. The direct observation of vital intermediates has been rarely reported on Fe/Ni-based phosphide electrocatalysts. Our exploration demonstrates an extraordinarily efficient and stable nonprecious TMP bifunctional electrocatalyst and provides a novel prospect to shed light on the intrinsic OER electrocatalytic behavior of Fe/Ni-based phosphide electrocatalysts.

Applying surface strain and coupling with pure or N/B-doped graphene to successfully achieve high HER catalytic activity in 2D layered SnP3-based nanomaterials: a first-principles investigation

Applying external strain and coupling with pure or N/B-doped graphene can be viewed as effective strategies to further improve the HER activity of 2D layered SnP₃ nanomaterials by optimizing the adsorption state of H* and electronic properties.

NiMoFe and NiMoFeP as Complementary Electrocatalysts for Efficient Overall Water Splitting and Their Application in PV-Electrolysis with STH 12.3

Complementary water splitting electrocatalysts used simultaneously in the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) can simplify water splitting systems. Herein, earth-abundant NiMoFe (NMF) and phosphorized NiMoFeP (NMFP) are synthesized as complementary overall water splitting (OWS) catalysts. First, NMF is tested as both the HER and OER promoter, which exhibits low overpotentials of 68 (HER) and 337 mV (OER). A quaternary NMFP is then prepared by simple phosphorization of NMF, which shows a much lower OER overpotential of 286 mV. The enhanced OER activity is attributed to the unique surface/core structure of NMFP. The surface phosphate acts as a proton transport mediator and expedites the rate-determining step. With the application of OER potential, the NMFP surface is composed of Ni(OH)₂ and FeOOH, active sites for OER, but the inner core consists of Ni, Mo, and Fe metals, serving as a conductive electron pathway. OWS with NMF-NMFP requires an applied voltage of 1.452 V to generate 10 mA cm^-2 , which is one of the lowest values among OWS results with transition-metal-based electrocatalysts. Furthermore, the catalysts are combined with tandem perovskite solar cells for photovoltaic (PV)-electrolysis, producing a high solar-to-hydrogen (STH) conversion efficiency of 12.3%.

Hierarchically Porous W-Doped CoP Nanoflake Arrays as Highly Efficient and Stable Electrocatalyst for pH-Universal Hydrogen Evolution

It is still challenging to develop high-efficiency and low-cost non-noble metal-based electrocatalysts for hydrogen evolution reaction (HER) in pH-universal electrolytes. Herein, hierarchically porous W-doped CoP nanoflake arrays on carbon cloth (W-CoP NAs/CC) are synthesized via facile liquid-phase reactions and a subsequent phosphorization process. The W-CoP NAs/CC hybrid can be directly employed as a binder-free electrocatalyst and delivers superior HER performance in pH-universal electrolytes. Especially, it delivers very low overpotentials of 89, 94, and 102 mV to reach a current density of 10 mA cm^-2 in acidic, alkaline, and neutral electrolytes, respectively. Furthermore, it shows a nearly 100% Faradaic efficiency as well as superior long-term stability with no decreasing up to 36 h in pH-universal electrolytes. The outstanding electrocatalytic performance of W-CoP NAs/CC can be mainly attributed to the porous W-doped nanoflake arrays, which not only afford rich exposed active sites, but also accelerate the access of electrolytes and the diffusion of H₂ bubbles, thus efficiently promoting the HER performance. This work provides a new horizon to rationally design and synthesize highly effective and stable non-noble metal phosphide-based pH-universal electrocatalysts for HER.