Exploring Layered Disorder in Lithium-Ion-Conducting Li3Y1-xInxCl6

Li3Y1-xInxCl6 undergoes a phase transition from trigonal to monoclinic via an intermediate orthorhombic phase. Although the trigonal yttrium containing the end member phase, Li3YCl6, synthesized by a mechanochemical route, is known to exhibit stacking fault disorder, not much is known about the monoclinic phases of the serial composition Li3Y1-xInxCl6. This work aims to shed light on the influence of the indium substitution on the phase evolution, along with the evolution of stacking fault disorder using X-ray and neutron powder diffraction together with solid-state nuclear magnetic resonance spectroscopy, studying the lithium-ion diffusion. Although Li3Y1-xInxCl6 with x ≤ 0.1 exhibits an ordered trigonal structure like Li3YCl6, a large degree of stacking fault disorder is observed in the monoclinic phases for the x ≥ 0.3 compositions. The stacking fault disorder materializes as a crystallographic intergrowth of faultless domains with staggered layers stacked in a uniform layer stacking, along with faulted domains with randomized staggered layer stacking. This work shows how structurally complex even the "simple" series of solid solutions can be in this class of halide-based lithium-ion conductors, as apparent from difficulties in finding a consistent structural descriptor for the ionic transport.

Engineering and regulating the interfacial stability between Li1.3Al0.3Ti1.7(PO4)3-based solid electrolytes and lithium metal anodes for solid-state lithium batteries

InCl3@Li1.3Al0.3Ti1.7(PO4)3-F (InCl3@LATP-F) solid electrolyte powders are designed and fabricated by coating a uniform InCl3 layer on the surface of F--doped Li1.3Al0.3Ti1.7(PO4)3 (LATP-F) solid powders via a feasible wet-chemical technique. The assembled Li/InCl3@LATP-F/Li cell can undergo longer cycles of 2500 h at 0.4 mA cm-2 without obvious increases in the overvoltage compared to 1837 h for the Li/LATP-F/Li cell, and the interfacial resistance demonstrates a sharp decrease from 3428 to 436 Ω for the Li/InCl3@LATP-F/Li cell during the first 500 h. Importantly, the assembled LiCoO2/InCl3@LATP-F/Li cell delivers a high discharge specific capacity of 126.4 mAh g-1 with a 95.42% capacity retention ratio after 100 cycles at 0.5 C, and the value easily returns to 112.9 mAh g-1 when the current density is abruptly set back to 0.1 C after different rate cycles. These improved results can be mainly attributed to the fact that the InCl3 layer with a lithiophilic nature can react with lithium metal to form a Li-In alloy, which can guarantee homogeneous lithium ion flux to avoid the accumulation of ions/electrons across the interface and suppress the growth of lithium dendrites. Moreover, the InCl3 layer can prevent direct contact of the LATP-F solid electrolyte and lithium metal to effectively alleviate the reduction reaction of Ti4+ and preserve the structural stability of the composite electrolyte. Therefore, this work may provide an effective strategy to engineer and regulate the interfacial stability between LATP solid electrolytes and lithium metal anodes for LATP-type solid-state lithium batteries.

Self-diffusion in polycrystalline Li1+x Ti2-x Al x (PO4)3 (0.2 ≤ x ≤ 0.4) samples followed by 7Li PFG (pulse field gradient) NMR spectroscopy

Short and long range lithium motions in powder Li_1+x Ti_2-x Al _x (PO₄)₃ (LTAP) NASICON compounds prepared by ceramic (x = 0.2 and 0.4) and sol-gel (x = 0.3 and 0.4) routes are discussed. ND diffraction and MAS-NMR spectroscopy were previously used to investigate structural features of these compounds. In particular, Fourier map differences showed that the amount of Li atoms allocated at M3 increases at the expense of M1 sites when the Li content increases. In this work, PFG-NMR results show that diffusion coefficients rise with the amount of lithium and temperature. The restricted diffusion inside NASICON particles is compared with "free" diffusion processes. At 300 K, diffusion coefficients D _PFG ∼ 5 × 10^-12 m² s^-1 have been deduced in ceramic x = 0.2 and 0.4 samples, decreasing with diffusion time Δ used in PFG experiments. In sol-gel samples, diffusion coefficients are near those of ceramic samples, but decrease faster with diffusion Δ times, as a consequence of the Li confinement inside sub-micrometric crystallites. The NMR spin-echo signal displays minima at specific q(γgδ) values that are related to the crystallite size. From R _dif ∼ q _m ^-1 distances, calculated from the position of minima, and from diffusion coefficients deduced for high Δ values, the mean crystallite size was estimated. Finally, from the temperature dependence of conductivity and diffusion coefficients, the activation energy and charge carriers concentrations were determined.

Exploiting Nanoscale Complexion in LATP Solid-State Electrolyte via Interfacial Mg2+ Doping

While great effort has been focused on bulk material design for high-performance All Solid-State Batteries (ASSBs), solid-solid interfaces, which typically extend over a nanometer regime, have been identified to severely impact cell performance. Major challenges are Li dendrite penetration along the grain boundary network of the Solid-State Electrolyte (SSE) and reductive decomposition at the electrolyte/electrode interface. A naturally forming nanoscale complexion encapsulating ceramic Li1+xAlxTi2-x(PO4)3 (LATP) SSE grains has been shown to serve as a thin protective layer against such degradation mechanisms. To further exploit this feature, we study the interfacial doping of divalent Mg2+ into LATP grain boundaries. Molecular Dynamics simulations for a realistic atomistic model of the grain boundary reveal Mg2+ to be an eligible dopant candidate as it rarely passes through the complexion and thus does not degrade the bulk electrolyte performance. Tuning the interphase stoichiometry promotes the suppression of reductive degradation mechanisms by lowering the Ti4+ content while simultaneously increasing the local Li+ conductivity. The Mg2+ doping investigated in this work identifies a promising route towards active interfacial engineering at the nanoscale from a computational perspective.

Conductivity Mechanism in Ionic 2D Carbon Nitrides: From Hydrated Ion Motion to Enhanced Photocatalysis

Carbon nitrides are among the most studied materials for photocatalysis; however, limitations arise from inefficient charge separation and transport within the material. Here, this aspect is addressed in the 2D carbon nitride poly(heptazine imide) (PHI) by investigating the influence of various counterions, such as M = Li⁺ , Na⁺ , K⁺ , Cs⁺ , Ba²⁺ , NH₄ ⁺ , and tetramethyl ammonium, on the material's conductivity and photocatalytic activity. These ions in the PHI pores affect the stacking of the 2D layers, which further influences the predominantly ionic conductivity in M-PHI. Na-containing PHI outperforms the other M-PHIs in various relative humidity (RH) environments (0-42%RH) in terms of conductivity, likely due to pore-channel geometry and size of the (hydrated) ion. With increasing RH, the ionic conductivity increases by 4-5 orders of magnitude (for Na-PHI up to 10^-5 S cm^-1 at 42%RH). At the same time, the highest photocatalytic hydrogen evolution rate is observed for Na-PHI, which is mirrored by increased photogenerated charge-carrier lifetimes, pointing to efficient charge-carrier stabilization by, e.g., mobile ions. These results indicate that also ionic conductivity is an important parameter that can influence the photocatalytic activity. Besides, RH-dependent ionic conductivity is of high interest for separators, membranes, or sensors.

Stable Interface Chemistry and Multiple Ion Transport of Composite Electrolyte Contribute to Ultra-long Cycling Solid-State LiNi0.8 Co0.1 Mn0.1 O2 /Lithium Metal Batteries

Severe interfacial side reactions of polymer electrolyte with LiNi_0.8 Co_0.1 Mn_0.1 O₂ (NCM811) cathode and Li metal anode restrict the cycling performance of solid-state NCM811/Li batteries. Herein, we propose a chemically stable ceramic-polymer-anchored solvent composite electrolyte with high ionic conductivity of 6.0×10^-4  S cm^-1 , which enables the solid-state NCM811/Li batteries to cycle 1500 times. The Li_1.4 Al_0.4 Ti_1.6 (PO₄ )₃ nanowires (LNs) can tightly anchor the essential N, N-dimethylformamide (DMF) in poly(vinylidene fluoride) (PVDF), greatly enhancing its electrochemical stability and suppressing the side reactions. We identify the ceramic-polymer-liquid multiple ion transport mechanism of the LNs-PVDF-DMF composite electrolyte by tracking the ⁶ Li and ⁷ Li substitution behavior via solid-state NMR. The stable interface chemistry and efficient ion transport of LNs-PVDF-DMF contribute to superior performances of the solid-state batteries at wide temperature range of -20-60 °C.

Nuclear magnetic resonance (NMR) studies of sintering effects on the lithium ion dynamics in Li1.5Al0.5Ti1.5(PO4)3

Various nuclear magnetic resonance (NMR) methods are combined to study the structure and dynamics of Li1.5Al0.5Ti1.5(PO4)3 (LATP) samples, which were obtained from sintering at various temperatures between 650 and 900 °C. 6Li, 27Al, and 31P magic angle spinning (MAS) NMR spectra show that LATP crystallites are better defined for higher calcination temperatures. Analysis of 7Li spin-lattice relaxation and line-shape changes indicates the existence of two species of lithium ions with clearly distinguishable jump dynamics, which can be attributed to crystalline and amorphous sample regions, respectively. An increase of the sintering temperature leads to higher fractions of the fast lithium species with respect to the slow one, but hardly affects the jump dynamics in either of the phases. Specifically, the fast and slow lithium ions show jumps in the nanoseconds regime near 300 and 700 K, respectively. The activation energy of the hopping motion in the LATP crystallites amounts to ca. 0.26 eV. 7Li field-gradient diffusometry reveals that the long-range ion migration is limited by the sample regions featuring slow transport. The high spatial resolution available from the high static field gradients of our setup allows the observation of the lithium ion diffusion inside the small (<100 nm) LATP crystallites, yielding a high self-diffusion coefficient of D = 2 × 10−12 m2/s at room temperature.

Sintering behavior and ionic conductivity of Li1.5Al0.5Ti1.5(PO4)3 synthesized with different precursors

Li1.5Al0.5Ti1.5(PO4)3 (LATP) powders were prepared from different NO x -free precursors using an aqueous-based solution-assisted solid-state reaction (SA-SSR). The sintering behavior, phase formation, microstructure and ionic conductivity of the powders were explored as a function of sintering temperature. The powders showed a relatively narrow temperature windows in which shrinkage occurred. Relative densities of 95% were reached upon heating between 900 and 960 °C. Depending on the morphological features of the primary particles, either homogeneous and intact microstructures with fine grains of about <2 µm in size or a broad grain size distribution, micro-cracks and grain cleavages were obtained, indicating the instability of the microstructure. Consequently, the ceramics with a homogeneous microstructure possessed a maximum total ionic conductivity of 0.67 mS cm−1, whereas other ceramics reached only 0.58 mS cm−1 and 0.21 mS cm−1.

Use of Solid-State NMR Spectroscopy for the Characterization of Molecular Structure and Dynamics in Solid Polymer and Hybrid Electrolytes

Solid-state NMR spectroscopy is an established experimental technique which is used for the characterization of structural and dynamic properties of materials in their native state. Many types of solid-state NMR experiments have been used to characterize both lithium-based and sodium-based solid polymer and polymer-ceramic hybrid electrolyte materials. This review describes several solid-state NMR experiments that are commonly employed in the analysis of these systems: pulse field gradient NMR, electrophoretic NMR, variable temperature T1 relaxation, T2 relaxation and linewidth analysis, exchange spectroscopy, cross polarization, Rotational Echo Double Resonance, and isotope enrichment. In this review, each technique is introduced with a short description of the pulse sequence, and examples of experiments that have been performed in real solid-state polymer and/or hybrid electrolyte systems are provided. The results and conclusions of these experiments are discussed to inform readers of the strengths and weaknesses of each technique when applied to polymer and hybrid electrolyte systems. It is anticipated that this review may be used to aid in the selection of solid-state NMR experiments for the analysis of these systems.

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

Energy storage materials are finding increasing applications in our daily lives, for devices such as mobile phones and electric vehicles. Current commercial batteries use flammable liquid electrolytes, which are unsafe, toxic, and environmentally unfriendly with low chemical stability. Recently, solid electrolytes have been extensively studied as alternative electrolytes to address these shortcomings. Herein, we report the early history, synthesis and characterization, mechanical properties, and Li+ ion transport mechanisms of inorganic sulfide and oxide electrolytes. Furthermore, we highlight the importance of the fabrication technology and experimental conditions, such as the effects of pressure and operating parameters, on the electrochemical performance of all-solid-state Li batteries. In particular, we emphasize promising electrolyte systems based on sulfides and argyrodites, such as LiPS5Cl and β-Li3PS4, oxide electrolytes, bare and doped Li7La3Zr2O12 garnet, NASICON-type structures, and perovskite electrolyte materials. Moreover, we discuss the present and future challenges that all-solid-state batteries face for large-scale industrial applications.

Mechanism of Water Dynamics in Hyaluronic Dermal Fillers Revealed by Nuclear Magnetic Resonance Relaxometry

1 H spin-lattice nuclear magnetic resonance relaxation experiments were performed for five kinds of dermal fillers based on hyaluronic acid. The relaxation data were collected over a broad frequency range between 4 kHz and 40 MHz, at body temperature. Thanks to the frequency range encompassing four orders of magnitude, the dynamics of water confined in the polymeric matrix was revealed. It is demonstrated that translation diffusion of the confined water molecules exhibits a two-dimensional character and the diffusion process is slower than diffusion in bulk water by 3-4 orders of magnitude. As far as rotational dynamics of the confined water is concerned, it is shown that in all cases there is a water pool characterized by a rotational correlation time of about 4×10-9  s. In some of the dermal fillers a fraction of the confined water (about 10 %) forms a pool that exhibits considerably slower (by an order of magnitude) rotational dynamics. In addition, the water binding capacity of the dermal fillers was quantitatively compared.

Synthesis and Properties of NaSICON-type LATP and LAGP Solid Electrolytes

Inorganic solid electrolytes play a critical role in solid-state lithium batteries achieving high safety levels and high energy densities. The synthetic approaches to solid electrolytes are important for both fundamental research and practical applications. Li_1+x Al_x Ti_2-x (PO₄ )₃ (LATP) and Li_1+x Al_x Ge_2-x (PO₄ )₃ (LAGP) are two representative solid electrolytes with a sodium superionic conductor (NaSICON) structure. Herein, LATP and LAGP solid electrolytes are reviewed from the synthesis perspective, and correlated with their structure and conductive properties, as well as their electrochemical applications in batteries. First, the solid- and liquid-based synthetic methods to LATP and LAGP solid electrolytes and the key influencing factors are described. Second, the crystal structures and phase purities obtained from different synthetic approaches are introduced. Third, the conductive mechanisms, composition effects, and synthetic effects on the conductivities of LATP and LAGP solid electrolytes are compared. Fourth, the electrochemical applications of these two solid electrolytes in full batteries are discussed, including roles as solid electrolytes, composite components in electrodes, and surface coatings on electrodes. In the last section, a brief outlook is provided on the future development of NaSICON-type solid electrolytes for all-solid-state batteries.

Review on Polymer-Based Composite Electrolytes for Lithium Batteries

Lithium-ion batteries have dominated the high performance and mobile market for last decade. Despite their dominance in many areas, the development of current commercial lithium-ion batteries is experiencing bottlenecks, limited by safety risks such as: leakage, burning, and even explosions due to the low-boiling point organic liquid electrolytes. Solid electrolyte is a promising option to solve or mitigate those issues. Among all solid electrolytes, polymer based solid electrolytes have the advantages of low flammability, good flexibility, excellent thermal stability, and high safety. Numerous researchers have focused on implementing solid polymer based Li-ion batteries with high performance. Nevertheless, low Li-ion conductivity and poor mechanical properties are still the main challenges in its commercial development. In order to tackle the issues and improve the overall performance, composites with external particles are widely investigated to form a polymer-based composite electrolyte. In light of their work, this review discusses the progress of polymer-based composite lithium ion's solid electrolytes. In particular, the structures, ionic conductivities, electrochemical/chemical stabilities, and fabrications of solid polymer electrolytes are introduced in the text and summarized at the end. On the basis of previous work, the perspectives of solid polymer electrolytes are provided especially toward the future of lithium ion batteries.

Lithium ion dynamics in LiZr2(PO4)3 and Li1.4Ca0.2Zr1.8(PO4)3

High ionic conductivity, electrochemical stability and small interfacial resistances against Li metal anodes are the main requirements to be fulfilled in powerful, next-generation all-solid-state batteries. Understanding ion transport in materials with sufficiently high chemical and electrochemical stability, such as rhombohedral LiZr2(PO4)3, is important to further improve their properties with respect to translational Li ion dynamics. Here, we used broadband impedance spectroscopy to analyze the electrical responses of LiZr2(PO4)3 and Ca-stabilized Li1.4Ca0.2Zr1.8(PO4)3 that were prepared following a solid-state synthesis route. We investigated the influence of the starting materials, either ZrO2 and Zr(CH3COO)4, on the final properties of the products and studied Li ion dynamics in the crystalline grains and across grain boundary (g.b.) regions. The Ca2+ content has only little effect on bulk properties (4.2 × 10-5 S cm-1 at 298 K, 0.41 eV), but, fortunately, the g.b. resistance decreased by 2 orders of magnitude. Whereas, 7Li spin-alignment echo nuclear magnetic resonance (NMR) confirmed long-range ion transport as seen by conductivity spectroscopy, 7Li NMR spin-lattice relaxation revealed much smaller activation energies (0.18 eV) and points to rapid localized Li jump processes. The diffusion-induced rate peak, appearing at T = 282 K, shows Li+ exchange processes with rates of ca. 109 s-1 corresponding, formally, to ionic conductivities in the order of 10-3 S cm-1 to 10-2 S cm-1.

Substitutional disorder: structure and ion dynamics of the argyrodites Li6PS5Cl, Li6PS5Br and Li6PS5I

Li NMR spectroscopy reveals rapid Li ion dynamics in the poor Li ion conductor Li₆PS₅I; long-range motion is, however, only possible for Li₆PS₅Br and Li₆PS₅Cl with anion site disorder.

Space-Charge Layers in All-Solid-State Batteries; Important or Negligible?

All-solid state batteries have the promise to increase the safety of Li-ion batteries. A prerequisite for high-performance all-solid-state batteries is a high Li-ion conductivity through the solid electrolyte. In recent decades, several solid electrolytes have been developed which have an ionic conductivity comparable to that of common liquid electrolytes. However, fast charging and discharging of all-solid-state batteries remains challenging. This is generally attributed to poor kinetics over the electrode-solid electrolyte interface because of poorly conducting decomposition products, small contact areas, or space-charge layers. To understand and quantify the role of space-charge layers in all-solid-state batteries a simple model is presented which allows to asses the interface capacitance and resistance caused by the space-charge layer. The model is applied to LCO (LiCoO₂) and graphite electrodes in contact with an LLZO (Li₇La₃Zr₂O₁₂) and LATP (Li_1.2Al_0.2Ti_1.8(PO₄)₃) solid electrolyte at several voltages. The predictions demonstrate that the space-charge layer for typical electrode-electrolyte combinations is about a nanometer in thickness, and the consequential resistance for Li-ion transport through the space-charge layer is negligible, except when layers completely depleted of Li-ions are formed in the solid electrolyte. This suggests that space-charge layers have a negligible impact on the performance of all-solid-state batteries.

Fast Na ion transport triggered by rapid ion exchange on local length scales

The realization of green and economically friendly energy storage systems needs materials with outstanding properties. Future batteries based on Na as an abundant element take advantage of non-flammable ceramic electrolytes with very high conductivities. Na₃Zr₂(SiO₄)₂PO₄-type superionic conductors are expected to pave the way for inherently safe and sustainable all-solid-state batteries. So far, only little information has been extracted from spectroscopic measurements to clarify the origins of fast ionic hopping on the atomic length scale. Here we combined broadband conductivity spectroscopy and nuclear magnetic resonance (NMR) relaxation to study Na ion dynamics from the µm to the angstrom length scale. Spin-lattice relaxation NMR revealed a very fast Na ion exchange process in Na_3.4Sc_0.4Zr_1.6(SiO₄)₂PO₄ that is characterized by an unprecedentedly high self-diffusion coefficient of 9 × 10⁻¹² m²s⁻¹ at −10 °C. Thus, well below ambient temperature the Na ions have access to elementary diffusion processes with a mean residence time τ_NMR of only 2 ns. The underlying asymmetric diffusion-induced NMR rate peak and the corresponding conductivity isotherms measured in the MHz range reveal correlated ionic motion. Obviously, local but extremely rapid Na⁺ jumps, involving especially the transition sites in Sc-NZSP, trigger long-range ion transport and push ionic conductivity up to 2 mS/cm at room temperature.

Correlating Transport and Structural Properties in Li1+ xAl xGe2- x(PO4)3 (LAGP) Prepared from Aqueous Solution

Li_{1+ x}Al _xGe_{2- x}(PO₄)₃ (LAGP) is a solid lithium-ion conductor belonging to the NASICON family, representing the solid solution of LiGe₂(PO₄)₃ and AlPO₄. The typical syntheses of LAGP either involve high-temperature melt-quenching, which is complicated and expensive, or a sol-gel process requiring costly organic germanium precursors. In this work, we report a simple method based on aqueous solutions without the need of ethoxide precursors. Using synchrotron and neutron diffraction, the crystal structure, the occupancies for Al and Ge, and the distribution of lithium were determined. Substitution of germanium by aluminum allows for an increased Li⁺ incorporation in the material and the actual Li⁺ content in the sample increases with the nominal Li⁺ content and a solubility limit is observed for higher aluminum content. By means of impedance spectroscopy, an increase in the ionic conductivity with increasing lithium content is observed. Whereas the lithium ionic conductivity improves, due to the increasing carrier density, the bulk activation energy increases. This correlation suggests that changes in the transport mechanism and correlated motion may be at play in the Li_{1+ x}Al _xGe_{2- x}(PO₄)₃ solid solution.

3D Fiber-Network-Reinforced Bicontinuous Composite Solid Electrolyte for Dendrite-free Lithium Metal Batteries

Replacement of flammable organic liquid electrolytes with solid Li⁺ conductors is a promising approach to realize excellent performance of Li metal batteries. However, ceramic electrolytes are either easily reduced by Li metal or penetrated by Li dendrites through their grain boundaries, and polymer electrolytes are also faced with instability on the electrode/electrolyte interface and weak mechanical property. Here, we report a three-dimensional fiber-network-reinforced bicontinuous solid composite electrolyte with flexible Li⁺-conductive network (lithium aluminum titanium phosphate (LATP)/polyacrylonitrile), which helps to enhance electrochemical stability on the electrode/electrolyte interface by isolating Li and LATP and suppress Li dendrites growth by mechanical reinforcement of fiber network for the composite solid electrolyte. The composite electrolyte shows an excellent electrochemical stability after 15 days of contact with Li metal and has an enlarged tensile strength (10.72 MPa) compared to the pure poly(ethylene oxide)-bistrifluoromethanesulfonimide lithium salt electrolyte, leading to a long-term stability and safety of the Li symmetric battery with a current density of 0.3 mA cm^-2 for 400 h. In addition, the composite electrolyte also shows good electrochemical and thermal stability. These results provide such fiber-reinforced membranes that present stable electrode/electrolyte interface and suppress lithium dendrite growth for high-safety all-solid-state Li metal batteries.

Development of a ReaxFF reactive force field for lithium ion conducting solid electrolyte Li1+xAlxTi2−x(PO4)3 (LATP)

Using a ReaxFF reactive force field, we investigated the composition-dependent ionic conductivity and the Li migration behaviors in Li_1+xAl_xTi_2−x(PO₄)₃ solid electrolyte.

Understanding Surface and Interfacial Chemistry in Functional Nanomaterials via Solid-State NMR

Surface and interfacial chemistry is of fundamental importance in functional nanomaterials applied in catalysis, energy storage and conversion, medicine, and other nanotechnologies. It has been a perpetual challenge for the scientific community to get an accurate and comprehensive picture of the structures, dynamics, and interactions at interfaces. Here, some recent examples in the major disciplines of nanomaterials are selected (e.g., nanoporous materials, battery materials, nanocrystals and quantum dots, supramolecular assemblies, drug-delivery systems, ionomers, and graphite oxides) and it is shown how interfacial chemistry can be addressed through the perspective of solid-state NMR characterization techniques.

Long-range Li ion diffusion in NASICON-type Li1.5Al0.5Ge1.5(PO4)3 (LAGP) studied by 7Li pulsed-gradient spin-echo NMR

PGSE NMR showed parameter-dependent ⁷Li diffusion for a solid conductor LAGP in micrometer space, suggesting disperse mobility of Li ions.

Crystal Structure of Garnet-Related Li-Ion Conductor Li7-3x Ga x La3Zr2O12: Fast Li-Ion Conduction Caused by a Different Cubic Modification?

Li-oxide garnets such as Li₇La₃Zr₂O₁₂ (LLZO) are among the most promising candidates for solid-state electrolytes to be used in next-generation Li-ion batteries. The garnet-structured cubic modification of LLZO, showing space group Ia-3d, has to be stabilized with supervalent cations. LLZO stabilized with Ga³⁺ shows superior properties compared to LLZO stabilized with similar cations; however, the reason for this behavior is still unknown. In this study, a comprehensive structural characterization of Ga-stabilized LLZO is performed by means of single-crystal X-ray diffraction. Coarse-grained samples with crystal sizes of several hundred micrometers are obtained by solid-state reaction. Single-crystal X-ray diffraction results show that Li_7-3x Ga _x La₃Zr₂O₁₂ with x > 0.07 crystallizes in the acentric cubic space group I-43d. This is the first definite record of this cubic modification for LLZO materials and might explain the superior electrochemical performance of Ga-stabilized LLZO compared to its Al-stabilized counterpart. The phase transition seems to be caused by the site preference of Ga³⁺. ⁷Li NMR spectroscopy indicates an additional Li-ion diffusion process for LLZO with space group I-43d compared to space group Ia-3d. Despite all efforts undertaken to reveal structure-property relationships for this class of materials, this study highlights the potential for new discoveries.