Floating Bimetallic Catalysts for Growing 30 cm-Long Carbon Nanotube Arrays with High Yields and Uniformity

Ultralong carbon nanotubes (CNTs) are considered as promising candidates for many cutting-edge applications. However, restricted by the extremely low yields of ultralong CNTs, their practical applications can hardly be realized. Therefore, new methodologies shall be developed to boost the growth efficiency of ultralong CNTs and alleviate their areal density decay at the macroscale level. Herein, a facile, universal, and controllable method for the in situ synthesis of floating bimetallic catalysts (FBCs) is proposed to grow ultralong CNT arrays with high yields and uniformity. Ferrocene and metal acetylacetonates serve as catalyst precursors, affording the successful synthesis of a series of FBCs with controllable compositions. Among these FBCs, the optimized FeCu catalyst increases the areal density of ultralong CNT arrays to a record-breaking value of ≈8100 CNTs mm-1 and exhibits a lifetime 3.40 times longer than that of Fe, thus achieving both high yields and uniformity. A 30-centimeters-long and high-density ultralong CNT array is also successfully grown with the assistance of FeCu catalysts. As evidenced by this kinetic model and molecular dynamics simulations, the introduction of Cu into Fe can simultaneously improve the catalyst fluidity and decrease carbon solubility, and an optimal catalytic performance will be achieved by balancing this tradeoff.

Hydrogenation of furfural to furfuryl alcohol over MOF-derived Fe/Cu@C and Fe3O4/Cu@C catalysts

With Cu-MOF-loaded Fe(NO3)3 as the precursor (Fe(NO3)3/Cu-MOF), Fe/Cu@C and Fe3O4/Cu@C catalysts were prepared from heating under the H2 and N2 atmosphere, respectively. When Fe(NO3)3/Cu-MOF was heated under different atmospheres, Cu-MOF...

Lignin-Derived Syringol and Acetosyringone from Palm Bunch Using Heterogeneous Oxidative Depolymerization over Mixed Metal Oxide Catalysts under Microwave Heating

Biomass valorization to building block chemicals in food and pharmaceutical industries has tremendously gained attention. To produce monophenolic compounds from palm empty fruit bunch (EFB), EFB was subjected to alkaline hydrothermal extraction using NaOH or K2CO3 as a promotor. Subsequently, EFB-derived lignin was subjected to an oxidative depolymerization using Cu(II) and Fe(III) mixed metal oxides catalyst supported on γ-Al2O3 or SiO2 as the catalyst in the presence of hydrogen peroxide. The highest percentage of total phenolic compounds of 63.87 wt% was obtained from microwave-induced oxidative degradation of K2CO3 extracted lignin catalyzed by Cu-Fe/SiO2 catalyst. Main products from the aforementioned condition included 27.29 wt% of 2,4-di-tert-butylphenol, 19.21 wt% of syringol, 9.36 wt% of acetosyringone, 3.69 wt% of acetovanillone, 2.16 wt% of syringaldehyde, and 2.16 wt% of vanillin. Although the total phenolic compound from Cu-Fe/Al2O3 catalyst was lower (49.52 wt%) compared with that from Cu-Fe/SiO2 catalyst (63.87 wt%), Cu-Fe/Al2O3 catalyst provided the greater selectivity of main two value-added products, syringol and acetosyrigone, at 54.64% and 23.65%, respectively (78.29% total selectivity of two products) from the NaOH extracted lignin. The findings suggested a promising method for syringol and acetosyringone production from the oxidative heterogeneous lignin depolymerization under low power intensity microwave heating within a short reaction time of 30 min.

Earth-abundant 3d-transition-metal catalysts for lignocellulosic biomass conversion

Transformation of biomass to chemicals and fuels is a long-term goal in both science and industry. However, high cost is one of the major obstacles to the industrialization of this sustainable technology. Thus, developing catalysts with high activity and low-cost is of great importance for biomass conversion. The last two decades have witnessed the increasing achievement of the use of earth-abundant 3d-transition-metals in catalysis due to their low-cost, high efficiency and excellent stability. Here, we aim to review the fast development and recent advances of 3d-metal-based catalysts including Cu, Fe, Co, Ni and Mn in lignocellulosic biomass conversion. Moreover, present research trends and invigorating perspectives on future development are given.

Highly efficient catalytic transfer hydrogenation of furfural over defect-rich amphoteric ZrO2 with abundant surface acid-base sites

Currently, the catalytic transformation and utilization of biomass-derived compounds are of great importance to the alleviation of environmental problems and sustainable development. Among them, furfural alcohol derived from biomass resources has been found to be one of the most prospective biomass platforms for high-value chemicals and biofuels. Herein, high-surface-area ZrO₂ with abundant oxygen defects and surface acid-base sites was synthesized and used as a heterogeneous catalyst for the catalytic transfer hydrogenation of furfural into furfural alcohol using alcohol as a hydrogen donor. The as-synthesized ZrO₂ exhibited excellent catalytic performance with 98.2% FA conversion and 97.1% FOL selectivity, even comparable with that of a homogeneous Lewis acid catalyst. A series of characterization studies and experimental results revealed that acid sites on the surface of ZrO₂ could adsorb and activate the C[double bond, length as m-dash]O bond in furfural and base sites could facilitate the formation of alkoxide species. The synergistic effect of surface acid-base sites affords a harmonious environment for the reaction, which is crucial for catalytic transfer hydrogenation of furfural with high efficiency. Furthermore, the as-prepared ZrO₂ catalyst also exhibited a potential application for the efficient catalytic transfer hydrogenation of a series of biomass-derived carbonyl compounds.

Metal-Catalyzed Hydrogenation of Biomass-Derived Furfural: Particle Size Effects and Regulation Strategies

The hydrogenation of furfural (FUR), a typical bio-based furan derivative, is a critical reaction within the roadmap for upgrading lignocellulosic biomass into high value-added chemicals and liquid fuels, the performance of which is strongly correlated with the catalysts' intrinsic peculiarities. Metal catalysts with tailorable sizes, uniform dispersions and robust sintering resistance are generally recognized as a prerequisite for obtaining better hydrogenation activity, selectivity and stability, which has prompted intensive research into metal particle size effects and their regulation strategies. The roles of metal particle sizes and corresponding dispersions of metal catalysts used for FUR hydrogenation have been clearly recognized to be crucial over the past decade. In this regard, this systematic Minireview aims to provide profound insights into particle size effects in the metal-catalyzed hydrogenation of FUR, as well as conditional and structural approaches to regulating these effects. In addition, from the aspect of catalyst stability, the impacts and improvements of the metal particle sintering issue are analyzed. Moreover, several suggestions are proposed in response to the challenges in regulating particle size effects. Furthermore, the viewpoints presented herein would potentially contribute to the rational development of metal hydrogenation catalysts and further help to boost a more sustainable biomass refining system.

Continuous Flow Upgrading of Selected C2-C6 Platform Chemicals Derived from Biomass

The ever increasing industrial production of commodity and specialty chemicals inexorably depletes the finite primary fossil resources available on Earth. The forecast of population growth over the next 3 decades is a very strong incentive for the identification of alternative primary resources other than petro-based ones. In contrast with fossil resources, renewable biomass is a virtually inexhaustible reservoir of chemical building blocks. Shifting the current industrial paradigm from almost exclusively petro-based resources to alternative bio-based raw materials requires more than vibrant political messages; it requires a profound revision of the concepts and technologies on which industrial chemical processes rely. Only a small fraction of molecules extracted from biomass bears significant chemical and commercial potentials to be considered as ubiquitous chemical platforms upon which a new, bio-based industry can thrive. Owing to its inherent assets in terms of unique process experience, scalability, and reduced environmental footprint, flow chemistry arguably has a major role to play in this context. This review covers a selection of C₂ to C₆ bio-based chemical platforms with existing commercial markets including polyols (ethylene glycol, 1,2-propanediol, 1,3-propanediol, glycerol, 1,4-butanediol, xylitol, and sorbitol), furanoids (furfural and 5-hydroxymethylfurfural) and carboxylic acids (lactic acid, succinic acid, fumaric acid, malic acid, itaconic acid, and levulinic acid). The aim of this review is to illustrate the various aspects of upgrading bio-based platform molecules toward commodity or specialty chemicals using new process concepts that fall under the umbrella of continuous flow technology and that could change the future perspectives of biorefineries.

Heterogeneous iron-containing nanocatalysts – promising systems for selective hydrogenation and hydrogenolysis

Bimetallic catalytic systems Fe–Me (Pt, Pd, Cu) demonstrate synergy in the activity/selectivity pattern in reactions involving hydrogen: selective hydrogenation of CC bonds, NO₂ and carbonyl groups and hydrogenolysis of C–O bonds.

Hydroprocessing of Oleic Acid for Production of Jet-Fuel Range Hydrocarbons over Cu and FeCu Catalysts

In the present study, a series of monometallic Cu/SiO2-Al2O3 catalysts exhibited immense potential in the hydroprocessing of oleic acid to produce jet-fuel range hydrocarbons. The synergistic effect of Fe on the monometallic Cu/SiO2-Al2O3 catalysts of variable Cu loadings (5–15 wt%) was ascertained by varying Fe contents in the range of 1–5 wt% on the optimized 13% Cu/SiO2-Al2O3 catalyst. At 340 °C and 2.07 MPa H2 pressure, the jet-fuel range hydrocarbons yield and selectivities of 51.8% and 53.8%, respectively, were recorded for the Fe(3)-Cu(13)/SiO2-Al2O3 catalyst. To investigate the influence of acidity of support on the cracking of oleic acid, ZSM-5 (Zeolite Socony Mobil–5) and HZSM-5(Protonated Zeolite Socony Mobil–5)-supported 3% Fe-13% Cu were also evaluated at 300–340 °C and 2.07 MPa H2 pressure. Extensive techniques including N2 sorption analysis, pyridine- Fourier Transform Infrared Spectroscopy (Pyridine-FTIR), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), and H2-Temperature Programmed Reduction (H2-TPR) analyses were used to characterize the materials. XPS analysis revealed the existence of Cu1+ phase in the Fe(3)-Cu(13)/SiO2-Al2O3 catalyst, while Cu metal was predominant in both the ZSM-5 and HZSM-5-supported FeCu catalysts. The lowest crystallite size of Fe(3)-Cu(13)/SiO2-Al2O3 was confirmed by XRD, indicating high metal dispersion and corroborated by the weakest metal–support interaction revealed from the TPR profile of this catalyst. CO chemisorption also confirmed high metal dispersion (8.4%) for the Fe(3)-Cu(13)/SiO2-Al2O3 catalyst. The lowest and mildest Brønsted/Lewis acid sites ratio was recorded from the pyridine–FTIR analysis for this catalyst. The highest jet-fuel range hydrocarbons yield of 59.5% and 73.6% selectivity were recorded for the Fe(3)-Cu(13)/SiO2-Al2O3 catalyst evaluated at 300 °C and 2.07 MPa H2 pressure, which can be attributed to its desirable textural properties, high oxophilic iron content, high metal dispersion and mild Brønsted acid sites present in this catalyst.

Tandem Hydrogenation/Hydrogenolysis of Furfural to 2-Methylfuran over a Fe/Mg/O Catalyst: Structure–Activity Relationship

The hydrodeoxygenation of furfural (FU) was investigated over Fe-containing MgO catalysts, on a continuous gas flow reactor, using methanol as a hydrogen donor. Catalysts were prepared either by coprecipitation or impregnation methods, with different Fe/Mg atomic ratios. The main product was 2-methylfuran (MFU), an important highly added value chemical, up to 92% selectivity. The catalyst design helped our understanding of the impact of acid/base properties and the nature of iron species in terms of catalytic performance. In particular, the addition of iron on the surface of the basic oxide led to (i) the increase of Lewis acid sites, (ii) the increase of the dehydrogenation capacity of the presented catalytic system, and (iii) to the significant enhancement of the FU conversion to MFU. FTIR studies, using methanol as the chosen probe molecule, indicated that, at the low temperature regime, the process follows the typical hydrogen transfer reduction, but at the high temperature regime, methanol dehydrogenation and methanol disproportionation were both presented, whereas iron oxide promoted methanol transfer. FTIR studies were performed using furfural and furfuryl alcohol as probe molecules. These studies indicated that furfuryl alcohol activation is the rate-determining step for methyl furan formation. Our experimental results clearly demonstrate that the nature of iron oxide is critical in the efficient hydrodeoxygenation of furfural to methyl furan and provides insights toward the rational design of catalysts toward C–O bonds’ hydrodeoxygenation in the production of fuel components.

Theoretical Study of the Mechanism of Furfural Conversion on the NiCuCu(111) Surface

The full potential energy surface for the hydrodeoxygenation of furfural to furan and other ring-opening products has been systematically investigated using periodic density functional theory including dispersion corrections (PBE-D3) on the bimetallic NiCuCu(111) surface. For furan formation, the most favorable first step is the dehydrogenation of furfural into furoyl (F-CHO + H = F-CO + 2H), the successive step is decarbonylation of furoyl into furanyl (F-CO + H = F + CO + 2H), and the third step of furan formation from the hydrogenation of furanyl (F + CO + 2H = FA + CO + H) is the rate-determining step. In addition, on the basis of the most stably adsorbed furan and H, the ring opening of furan was found to be more favorable for producing many chemicals such as propane, butanal, butanol, and butene. In summary, furan is the main product of furfural conversion on the NiCuCu(111) surface. Since results have been obtained only for the NiCuCu(111) surface constructed by replacing the topmost Cu atoms by Ni atoms, the entire experimentally observed reactivity and selectivity of bimetallic CuNi catalysts for different construction methods cannot be fully rationalized. Nevertheless, the results provide the basis for investigating the intrinsic activity of CuNi catalysts in the hydrodeoxygenation of oxygenates involved in the refining of biomass-derived oils.

Recent Advances in Catalytic Hydrogenation of Furfural

Furfural has been considered as one of the most promising platform molecules directly derived from biomass. The hydrogenation of furfural is one of the most versatile reactions to upgrade furanic components to biofuels. For instance, it can lead to plenty of downstream products, such as (tetrahydro)furfuryl alcohol, 2-methyl(tetrahydro)furan, lactones, levulinates, cyclopentanone(l), or diols, etc. The aim of this review is to discuss recent advances in the catalytic hydrogenation of furfural towards (tetrahydro)furfuryl alcohol and 2-methyl(tetrahydro)furan in terms of different non-noble metal and noble metal catalytic systems. Reaction mechanisms that are related to the different catalytic materials and reaction conditions are properly discussed. Selective hydrogenation of furfural could be modified not only by varying the types of catalyst (nature of metal, support, and preparation method) and reaction conditions, but also by altering the reaction regime, namely from batch to continuous flow. In any case, furfural catalytic hydrogenation is an open research line, which represents an attractive option for biomass valorization towards valuable chemicals and fuels.

Influence of the Incorporation of Basic or Amphoteric Oxides on the Performance of Cu-Based Catalysts Supported on Sepiolite in Furfural Hydrogenation

Cu-based catalysts supported on sepiolite have been tested in vapor-phase hydrogenation of furfural. The incorporation of basic or amphoteric metal oxides (magnesium oxide, zinc oxide, or cerium oxide) improves the catalytic behavior, reaching a maximum furfural conversion above 80% after 5 h of reaction at 210 °C. In all cases, the main product is furfuryl alcohol, obtaining 2-methylfuran in lower proportions. The incorporation of these metal oxide species ameliorates the dispersion of metallic Cu nanoparticles, increasing the number of available Cu0-sites, which enhances the catalytic performance. The presence of acid sites favors the hydrogenolysis of furfuryl alcohol towards 2-methylfuran, although it also causes an increase of carbon species on its surface, which is associated with the catalytic deactivation of the catalyst along the time-on-stream.

Advances in porous and nanoscale catalysts for viable biomass conversion

Solid catalysts with unique porosity and nanoscale properties play a promising role for efficient valorization of biomass into sustainable advanced fuels and chemicals.

How Catalysts and Experimental Conditions Determine the Selective Hydroconversion of Furfural and 5-Hydroxymethylfurfural

Furfural and 5-hydroxymethylfurfural stand out as bridges connecting biomass raw materials to the biorefinery industry. Their reductive transformations by hydroconversion are key routes toward a wide variety of chemicals and biofuels, and heterogeneous catalysis plays a central role in these reactions. The catalyst efficiency highly depends on the nature of metals, supports, and additives, on the catalyst preparation procedure, and obviously on reaction conditions to which catalyst and reactants are exposed: solvent, pressure, and temperature. The present review focuses on the roles played by the catalyst at the molecular level in the hydroconversion of furfural and 5-hydroxymethylfurfural in the gas or liquid phases, including catalytic hydrogen transfer routes and electro/photoreduction, into oxygenates or hydrocarbons (e.g., furfuryl alcohol, 2,5-bis(hydroxymethyl)furan, cyclopentanone, 1,5-pentanediol, 2-methylfuran, 2,5-dimethylfuran, furan, furfuryl ethers, etc.). The mechanism of adsorption of the reactant and the mechanism of the reaction of hydroconversion are correlated to the specificities of each active metal, both noble (Pt, Pd, Ru, Au, Rh, and Ir) and non-noble (Ni, Cu, Co, Mo, and Fe), with an emphasis on the role of the support and of additives on catalytic performances (conversion, yield, and stability). The reusability of catalytic systems (deactivation mechanism, protection, and regeneration methods) is also discussed.

Direct conversion of carbohydrates to diol by the combination of niobic acid and a hydrophobic ruthenium catalyst

A variety of carbohydrates were converted to tetrahydro-2,5-furandimethanol in one step by the combination of Ru/SiO₂-TM and Nb₂O₅-FP.

Highly efficient nitrogen-doped hierarchically porous carbon supported Ni nanoparticles for the selective hydrogenation of furfural to furfuryl alcohol

Nickel nanoparticles supported on nitrogen doped hierarchically porous carbon (Ni/CN) are found to be highly efficient and reusable catalysts for the selective hydrogenation of biomass-derived furfural to furfuryl alcohol (FA).