Oxidation, defunctionalization and catalyst life cycle of carbon nanotubes: a Raman spectroscopy view

Sensitive surface plasmon resonance biosensor by optimized carboxylate functionalized carbon nanotubes/chitosan for amlodipine detecting

The adoption of biophotonic sensing technologies holds significant promise for application in health care and biomedical industries in all aspects of human life. Then, this piece of writing employs the powerful effective medium theory and FDTD simulation to anticipate the most favorable state and plasmonic attributes of a magnificent nanocomposite, comprising carboxylate functionalized carbon nanotubes and chitosan (CS). Furthermore, it thoroughly explores the exhibited surface plasmon resonance behaviors of this composite versus the quantity of CS variation. Subsequently, enlightening simulations are conducted on the nanocomposite with a delicate layer and a modified golden structure integrating as a composite. The intricate simulations eventually unveil an optimal combination to pave the way for crafting an exceptional specific biosensor that far surpasses its counterpart as a mere Au thin layer in terms of excellence. The proposed biosensor demonstrated linear behavior across a wide range from 0.01 μM to 150 μM and achieved a detection limit of 10 nM, with a sensitivity of 134◦RIU-1.

Simulation and Verification of the Direct Current Electric Field on Fabricating High Porosity f-MWCNTs Thin Films by Electrophoretic Deposition Technique

Electrophoretic deposition (EPD) is the potential process in high porosity thin films' fabrication or complex surface coating for perovskite photovoltaics. Here, the electrostatic simulation is introduced to optimize the EPD cell design for the cathodic EPD process based on functionalized multiwalled carbon nanotubes (f-MWCNTs). The similarity between the thin film structure and the electric field simulation is evaluated by scanning electron microscopy (SEM) and atomic force microscopy (AFM) results. The thin-film surface at the edge has a higher roughness (Ra) compared to the center position (16.48 > 10.26 nm). The f-MWCNTs at the edge position tend to be twisted and bent due to the torque of the electric field. The Raman results show that f-MWCNTs with low defect density are more easily to be positively charged and deposited on the ITO surface. The distribution of oxygen and aluminum atoms in the thin film reveals that the aluminum atoms tend to have adsorption/electrostatic attraction to the interlayer defect positions of f-MWCNTs without individually depositing onto the cathode. Finally, this study can reduce the cost and time for the scale-up process by optimizing the input parameters for the complete cathodic electrophoretic deposition process through electric field inspection.

A study on signal enhancement of a Raman probe using an optical pickup unit

A simplified fabrication method for an optical pickup unit (OPU)-based Raman probe was introduced. The use of OPU tracking mode was examined to increase the Raman signal and reduce background signals. Unlike most Raman systems, the tracking mode of the OPU moves the objective lens in the x (or y) direction, thus resulting in a significantly reduced background signal and increased Raman signal intensity. These results can be explained by two factors, such as reducing the surface scattering of the incident light from the objective lens and decreasing signal blocking by a dot mirror, which depends on the horizontal position of the objective lens. The reproducibility of the OPU Raman in tracking mode is higher than the OPU Raman in normal mode. The peak position deviation was calculated to be around ±3 cm⁻¹. The Raman spectra of normal organic samples were obtained under the same conditions and recorded as per the applied voltage in the OPU tracking mode to validate the fabricated device. The objective lens shifts resulted in increased Raman peaks and reduced background signals. The maximum peak-position difference for all samples was 10 cm⁻¹ compared to reference peaks obtained using a commercial Raman system.

Poly-NIPAM/Fe3O4/multiwalled carbon nanotube nanocomposites for kerosene removal from water

Multiwalled carbon nanotubes (MWCNTs) were oxidized using a mixture of H₂SO₄ and HNO₃, and the oxidized MWCNTS were decorated with magnetite (Fe₃O₄). Finally, poly-N-isopropyl acrylamide-co-butyl acrylate (P-NIPAM) was added to obtain P-NIPAM/Fe/MWCNT nanocomposites. The nanosorbents were characterized by various techniques, including X-ray diffraction, transmission electron microscopy, scanning electron microscopy, thermogravimetric analysis, and Brunauer-Emmett-Teller analysis. The P-NIPAM/Fe/MWCNT nanocomposites exhibited increased surface hydrophobicity. Owing to their higher adsorption capacity, their kerosene removal efficiency was 95%; by contrast, the as-prepared, oxidized, and magnetite-decorated MWCNTs had removal efficiencies of 45%, 55%, and 68%, respectively. The P-NIPAM/Fe/MWCNT nanocomposites exhibited a sorbent capacity of 8.1 g/g for kerosene removal from water. The highest kerosene removal efficiency from water was obtained at a process time of 45 min, sorbent dose of 0.005 g, solution temperature of 40 °C, and pH 3.5. The P-NIPAM/Fe/MWCNTs showed excellent stability after four cycles of kerosene removal from water followed by regeneration. The reason may be the increase in the positive charge of the polymer at pH 3.5 and the increased adsorption affinity of the adsorbent toward the kerosene contaminant. The pseudo second-order model was found to be the most suitable model for studying the kinetics of the adsorption reaction.

Advances in preparation, mechanism and applications of various carbon materials in environmental applications: A review

Carbon-related materials are now widely investigated in a various industrial field due to their excellent and unique qualities. It must be tailored to the application in such a way that it fits the application. At the same time, it needs to be generated in sufficient quantities for commercial use, and the synthesis method is the major sticking point here. Because most new materials are discovered by chance, the synthesis process described here may not be the most effective way to create them. The research is merely a steppingstone to discovering a different approach, and it will continue until the substance is no longer being used. If you're developing materials for any purpose, synthesis processes are essential. Fullerene, carbon nanotubes (CNT), graphene, and MXene are only a few of the carbon-based compounds discussed in this overview study, which also gives a brief prognosis on the materials future. Furthermore, the environmental application of these carbon materials was discussed and commented.

Balancing Between Polarization and Conduction Loss toward Strong Electromagnetic Wave Absorption of Hard Carbon Particles with Morphology Heterogeneity

The heterostructure and hierarchical morphology of carbonaceous absorbents play an important role in the construction of high-performance electromagnetic wave absorbing materials. Herein, novel micron-scale hard carbon particles with morphology heterogeneity were developed as lightweight superior electromagnetic wave absorbents via a facile and ecofriendly process. The as-prepared hard carbon particle composed of pseudographite and a highly disordered region shows a unique heterostructure. Concurrently, constructing a multilevel geometric shape and size can cause a decrease of the percolation threshold and an excellent balance between polarization and conduction loss, which enhances the electromagnetic wave absorption significantly. The composites (thickness d = 2.36 mm) filled with morphology-heterogeneity hard carbon particles (15 wt %) achieve an excellent electromagnetic wave absorption with a minimum reflection loss of -78.0 dB at 10.2 GHz and effective absorption bandwidth (<-10 dB) of 3.1 GHz (8.8-11.9 GHz). Compared to the traditional carbonaceous absorbents with complex microstructures and/or multiple chemical components, this work presents a feasible idea for the development of an efficient carbonaceous absorbent to realize practical applications.

Distributed Strain Monitoring Using Nanocomposite Paint Sensing Meshes

Strain measurements are vital for monitoring the load-bearing capacity and safety of structures. A common approach is to affix strain gages onto structural surfaces. On the other hand, most aerospace, automotive, civil, and mechanical structures are painted and coated, often with many layers, prior to their deployment. There is an opportunity to design smart and multifunctional paints that can be directly pre-applied onto structural surfaces to serve as a sensing layer among their other layers of functional paints. Therefore, the objective of this study was to design a strain-sensitive paint that can be used for structural monitoring. Carbon nanotubes (CNT) were dispersed in paint by high-speed shear mixing, while paint thinner was employed for adjusting the formulation's viscosity and nanomaterial concentration. The study started with the design and fabrication of the CNT-based paint. Then, the nanocomposite paint's electromechanical properties and its sensitivity to applied strains were characterized. Third, the nanocomposite paint was spray-coated onto patterned substrates to form "Sensing Meshes" for distributed strain monitoring. An electrical resistance tomography (ERT) measurement strategy and algorithm were utilized for reconstructing the conductivity distribution of the Sensing Meshes, where the magnitude of conductivity (or resistivity) corresponded to the magnitude of strain, while strain directionality was determined based on the strut direction in the mesh.

V2O5, CeO2 and Their MWCNTs Nanocomposites Modified for the Removal of Kerosene from Water

In this paper, the application of multiwalled carbon nanotubes (MWCNTs) based on metal oxide nanocomposites as adsorbents for the removal of hydrocarbons such as kerosene from water was investigated. Functionalized MWCNTs were obtained by chemical oxidation using concentrated sulfuric and nitric acids. V₂O₅, CeO_2, and V₂O₅:CeO₂ nanocomposites were prepared using the hydrothermal method followed by deposition of these oxides over MWCNTs. Individual and mixed metal oxides, fresh MWCNTs, and metal oxide nanoparticle-doped MWCNTs using different analysis techniques were characterized. XRD, TEM, SEM, EDX, AFM, Raman, TG/DTA, and BET techniques were used to determine the structure as well as chemical and morphological properties of the newly prepared adsorbents. Fresh MWCNTs, Ce/MWCNTs, V/MWCNTs, and V:Ce/MWCNTs were applied for the removal of kerosene from a model solution of water. GC analysis indicated that high kerosene removal efficiency (85%) and adsorption capacity (4270 mg/g) after 60 min of treatment were obtained over V:Ce/MWCNTs in comparison with fresh MWCNTs, Ce/MWCNTs and V/MWCNTs. The kinetic data were analyzed using the pseudo-first order, pseudo-second order, and intra-particle diffusion rate equations.

Polyethylene over magnetite-multiwalled carbon nanotubes for kerosene removal from water

In this study, a nano-adsorbent was prepared for kerosene removal from water. Multiwalled carbon nanotubes (MWCNTs) were functionalized with concentrated HNO₃ (nitric acid). Subsequently, Fe₃O₄ (magnetite) nanoparticles were deposited on the MWCNTs to prepare a magnetite/MWCNTs (Fe-MWCNTs) nanocomposite. Then, polyethylene was added to the Fe-MWCNTs to fabricate a polyethylene/magnetite/MWCNTs (PE/Fe-MWCNTs) novel nanocomposite. The nano-adsorbent was characterized using BET, FTIR, Raman, XRD, TEM, and SEM. A kerosene-water model mixture was used for adsorption tests. Several parameters: adsorption time, adsorbent dose, solution pH, solution temperature, and kerosene concentration in the kerosene-water model mixture, were analyzed during adsorption experiments. After each batch experiment, kerosene concentration was determined using high-performance liquid chromatography (HPLC). Magnetic field was used to remove the adsorbent after each experiment. The kerosene adsorption capacity and removal efficiency of the PE/Fe-MWCNTs nanocomposite (3560 mg/g and 71.2 %, respectively) were higher than those of Fe-MWCNTs, ox-MWCNTs, and fresh MWCNTs (3154 mg/g and 63.1 %, 2204 mg/g and 44.0 %, and 2092 mg/g and 41.8 %, respectively). Kerosene adsorption followed a pseudo-second-order kinetic model (R² = 0.999) and the Langmuir isotherm model, suggesting that adsorption was uniform and homogenous process.

Carbon nanotubes derived from waste cooking oil for the removal of emerging contaminants

Multi-walled carbon nanotube (MWCNT) were synthesized using ethyl acetate and waste cooking oil as more green and sustainable carbon sources, and further successfully applied for the adsorption of norfloxacin and 17α-ethinylestradiol.

Green and Highly-Efficient Microwave Synthesis Route for Sulfur/Carbon Composite for Li-S Battery

Multiporous carbons (MPCs) are prepared using ZnO as a hard template and biomass pyrolysis oil as the carbon source. It is shown that the surface area, pore volume, and mesopore/micropore ratio of the as-prepared MPCs can be easily controlled by adjusting the ZnO/oil ratio. Sulfur/MPC (S/MPC) composite is prepared by blending sulfur powder with the as-prepared MPCs followed by microwave heating at three different powers (100 W/200 W/300 W) for 60 s. The unique micro/mesostructure characteristics of the resulting porous carbons not only endow the S/MPC composite with sufficient available space for sulfur storage, but also provide favorable and efficient channels for Li-ions/electrons transportation. When applied as the electrode material in a lithium-ion battery (LIB), the S/MPC composite shows a reversible capacity (about 500 mAh g⁻¹) and a high columbic efficiency (>95%) after 70 cycles. Overall, the method proposed in this study provides a simple and green approach for the rapid production of MPCs and S/MPC composite for high-performance LIBs.

Silicone Rubber Composites Reinforced by Carbon Nanofillers and Their Hybrids for Various Applications: A Review

Without fillers, rubber types such as silicone rubber exhibit poor mechanical, thermal, and electrical properties. Carbon black (CB) is traditionally used as a filler in the rubber matrix to improve its properties, but a high content (nearly 60 per hundred parts of rubber (phr)) is required. However, this high content of CB often alters the viscoelastic properties of the rubber composite. Thus, nowadays, nanofillers such as graphene (GE) and carbon nanotubes (CNTs) are used, which provide significant improvements to the properties of composites at as low as 2–3 phr. Nanofillers are classified as those fillers consisting of at least one dimension below 100 nanometers (nm). In the present review paper, nanofillers based on carbon nanomaterials such as GE, CNT, and CB are explored in terms of how they improve the properties of rubber composites. These nanofillers can significantly improve the properties of silicone rubber (SR) nanocomposites and have been useful for a wide range of applications, such as strain sensing. Therefore, carbon-nanofiller-reinforced SRs are reviewed here, along with advancements in this research area. The microstructures, defect densities, and crystal structures of different carbon nanofillers for SR nanocomposites are characterized, and their processing and dispersion are described. The dispersion of the rubber composites was reported through atomic force microscopy (AFM), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The effect of these nanofillers on the mechanical (compressive modulus, tensile strength, fracture strain, Young’s modulus, glass transition), thermal (thermal conductivity), and electrical properties (electrical conductivity) of SR nanocomposites is also discussed. Finally, the application of the improved SR nanocomposites as strain sensors according to their filler structure and concentration is discussed. This detailed review clearly shows the dependency of SR nanocomposite properties on the characteristics of the carbon nanofillers.

One-Step Construction of Multi-Walled CNTs Loaded with Alpha-Fe2O3 Nanoparticles for Efficient Photocatalytic Properties

The aggregation and the rapid restructuring of the photoinduced electron−hole pairs restructuring in the process of photoelectric response remains a great challenge. In this study, a kind of Multi-walled carbon nanotubes loaded Alpha-Fe₂O₃ (CNTs/α-Fe₂O₃) heterostructure composite is successfully prepared via the one-step method. Due to the synergistic effect in the as-prepared CNTs/α-Fe₂O₃, the defect sites and oxygen-containing functional groups of CNTs can dramatically improve the interface charge separation efficiency and prevent the aggregation of α-Fe₂O₃. The improved photocurrent and enhanced hole–electron separation rate in the CNTs/α-Fe₂O₃ is obtained, and the narrower band gap is measured to be 2.8 ev with intensive visible-light absorption performance. Thus, the CNTs/α-Fe₂O₃ composite serves as an excellent visible light photocatalyst and exhibits an outstanding photocatalytic activity for the cationic dye degradation of rhodamine B (RhB). This research supplies a fresh application area forα-Fe₂O₃ photocatalyst and initiates a new approach for design of high efficiency photocatalytic materials.

Conversion of Secondary C3-C4 Aliphatic Alcohols on Carbon Nanotubes Consolidated by Spark Plasma Sintering

We analyze how the changes in the dimension of carbon nanomaterial (CNM) affect their catalytic conversion of secondary aliphatic alcohols. Carbon nanotubes (CNTs) consolidated by spark plasma sintering (SPS) were inactive in the conversion of secondary C₃-C₄ aliphatic alcohols because of the «healing» of defects in carbon structure during SPS. Gas-phase treatment of consolidated CNTs with HNO₃ vapors led to their surface oxidation without destruction of the bulk structure of pellets. The oxygen content in consolidated CNTs determined by X-ray photoelectron spectroscopy increased from 11.3 to 14.9 at. % with increasing the oxidation time from 3 to 6 h. Despite the decrease in the specific surface area, the oxidized samples showed enhanced catalytic activity in alcohol conversion because of the increased number of oxygen radicals with unpaired electrons, which was established by electron paramagnetic resonance spectroscopy. We conclude that the structure of CNM determines the content and/or ratio of sp² and sp³-hybridized carbon atoms in the material. The experimental and literature data demonstrated that sp³-hybridized carbon atoms on the surface are probably the preferable site for catalytic conversion of alcohols.

Tuning Magnetic Properties of a Carbon Nanotube-Lanthanide Hybrid Molecular Complex through Controlled Functionalization

Molecular magnets attached to carbon nanotubes (CNT) are being studied as potential candidates for developing spintronic and quantum technologies. However, the functionalization routes used to develop these hybrid systems can drastically affect their respective physiochemical properties. Due to the complexity of this systems, little work has been directed at establishing the correlation between the degree of functionalization and the magnetic character. Here, we demonstrate the chemical functionalization degree associated with molecular magnet loading can be utilized for controlled tuning the magnetic properties of a CNT-lanthanide hybrid complex. CNT functionalization degree was evaluated by interpreting minor Raman phonon modes in relation to the controlled reaction conditions. These findings were exploited in attaching a rare-earth-based molecular magnet (Gd-DTPA) to the CNTs. Inductively coupled plasma mass spectrometry, time-of-flight secondary ion mass spectrometry and super conducting quantum interference device (SQUID) measurements were used to elucidate the variation of magnetic character across the samples. This controlled Gd-DTPA loading on the CNT surface has led to a significant change in the nanotube intrinsic diamagnetism, showing antiferromagnetic coupling with increase in the Weiss temperature with respect to increased loading. This indicates that synthesis of a highly correlated spin system for developing novel spintronic technologies can be realized through a carbon-based hybrid material.

Fabricating a Raman spectrometer using an optical pickup unit and pulsed power

Although Raman spectroscopy is a major analytical tool in modern chemical experiments, commercial Raman spectrometers remain very pricey for educational and research purposes in individual university laboratories. Thus, this study focused on the structural similarity between the Raman spectrometer and an optical pickup unit (OPU), which is an inexpensive compact optical device used for a part of optical discs. The study investigated whether or not a full set of Raman spectrometer can be developed at a cost of less than 1,000 US$. The OPU-based Raman spectrometer was fabricated using 3D printer-made components, a Raman edge filter, and a laser diode with a wavelength of 520 nm as the light source. A function generator was used as a pulsed power source to analyze the characteristics of the OPU Raman spectrometer according to various frequencies and duty ratios. When using a pulsed DC power supply, the laser wavelength tended to move to a longer wavelength with increases in duty ratios. That is, the higher the frequency at the same duty ratio, the weaker the background light intensity compared with the scattered Raman signal intensity. The findings illustrate that Raman signal strength can be adjusted by adjusting the focal length of the objective lens of the OPU through an external adjustment of an additional DC power. In the Raman spectra of all solid and liquid samples used, the maximum error rate reached approximately 11 cm⁻¹, whereas the maximum intensity deviation reached approximately ± 6%. The cost of the complete OPU Raman spectrometer is less than 1,100 US$ using a function generator as power source and less than 930 US$ using a DC adapter. If the optical density (OD) 6 filter can be replaced with the OD 4 filter, then the costs are expected to decrease to approximately 730 US$.

Real-Time Measurement of Airborne Carbon Nanotubes in Workplace Atmospheres

With growing applications of carbon nanomaterials, there is a concern over health risks presented by inhalation of carbon nanotube (CNT) aerosol in workplace atmospheres. Current methods used for CNT aerosol measurement lack selectivity to specific form of carbonaceous component or allotrope of interest. Moreover, the detection limits of these methods are also inadequate for short-term monitoring. Here, we describe, for the first time, a near real-time, field-portable instrument for selective quantification of airborne CNT concentration. The approach uses an automated cyclical scheme involving collect-analyze-ablate steps to obtain continuous near real-time measurement using Raman spectroscopy. The method achieves significantly lower detection limits by employing corona-assisted particle microconcentration for efficient coupling with laser Raman spectroscopy. A combination of techniques involving (i) use of characteristic Raman peaks, (ii) distinct ratio of disordered and graphitic peaks, and (iii) principal component classification and regression is employed to identify and quantify the specific form of the aerosolized carbonaceous nanomaterial. We show that the approach is capable of selectively quantifying trace single-walled CNT in the presence of interfering agents such as diesel particulate matter. The detection limit of the method for the single-walled CNT studied in this work was 60 ng m^-3, corresponding to a 10 min aerosol collection period, which is significantly lower than that for the NIOSH Method 5040 (∼0.15 μg m^-3 for an 8-h collection on a 25 mm filter at 4 L min^-1), a commonly used method for elemental carbon. We demonstrate the automated real-time capability of this field-portable method by continuously measuring a transient single-walled CNT aerosol.

Metal-support interactions in the design of heterogeneous catalysts for redox processes

The effect of the metal-support interaction (MSI) has been discussed for several types of catalytic systems comprising metal nanoparticles (Ni, Pd, Au, Fe) on oxide and carbon supports, showing promising catalytic properties in hydrogenation of unsaturated C–C bonds, hydrodechlorination (HDC) of chlorinated organic molecules and CO total oxidation. The MSI of a different strength, from the redistribution of the electron density of nanoparticles (NPs) to the chemical interactions, is determined by the composition of the support and the active site, the method of active metal deposition, calcination temperature, particle size etc. The types of MSI considered in this review include: (1) the interaction of the active metal (Me) NPs with alumina and modified zirconia to form several oxidation states of Me in the composition of surface or bulk chemical compounds with a support; (2) the influence of oxide (alumina, silica) or carbon (highly oriented pyrolytic graphite, Sibunit) supports on the formation of active sites in the catalysts with ultra-low Me loading prepared by deposition of pre-formed metal NPs produced by laser electrodispersion (LED) or as colloidal dispersion; (3) the anchoring of Me NPs on the surface of carbon supports (nanodiamonds and carbon nanotubes) directly with a support surface, e.g. through surface defects, or through surface functional groups; (4) ‘reverse’ MSI in the Me@C composites, consisting of metal NPs, covered with the defected graphene layers or immersed into carbon matrix. It is demonstrated on the example of LED systems, that oxidation of metal under MSI is less significant in carbon-supported systems than in oxide-supported ones, but charge effects can play a noticeable role for both types of supports. Different ways of MSI tuning provide the possibilities to achieve the optimal Men+/Me0 ratio in the catalysts for HDC of mono- and polychlorinated organic molecules, including persistent organic pollutants. One of these ways is tuning the composition of functional groups on the surface of nanodiamonds and carbon nanotubes by additional treatments to achieve the desirable metal anchoring, the optimal metal NPs size and the improved catalytic properties. Unusual type of MSI is represented by the activation of thin graphene shell of Me@C composites by the presence of defects in the shell and a transition metal (Ni, Fe) in subsurface layer. This effect allows H2 activation that is a significant step in many industrially important reactions. The selectivity and activity of such systems can be intentionally changed by varying the nature of metal and reaction temperature. Significant attention has been given in the review to the novel catalytic systems described in the previous works of the authors.

Paclitaxel Encapsulation into Dual-Functionalized Multi-Walled Carbon Nanotubes

This work reports the synthesis of multi-walled carbon nanotubes (CNTs) from xylene/ferrocene using catalytic chemical vapor deposition technique. Following characterization using transmission electron microscopy (TEM), energy-dispersive X-ray (EDX), and Raman spectroscopy, CNT surface was dual-functionalized using ethylenediamine and phenylboronic acid groups. Average diameter of CNTs was calculated to be 16.5 nm. EDX spectra confirmed the existence of carbonaceous deposits on the tube's surface. Scattered electron diffraction and X-ray peak broadening calculations showed consistent inter-planer distance of the grown CNTs. Chemical functionalization, confirmed from FT-IR and Raman spectra, showed an enhanced dispersibility of CNTs in water. We describe the changes in the first- and second-order regions of the Raman spectra following the encapsulation of an anti-cancer drug, paclitaxel (PLX), into the free volume of functionalized CNTs. High PLX loading, achieved through its non-covalent π-π stacking within the CNT interior, is confirmed through the blue-shifted, softened G band in the Raman spectrum. While not addressed here, we will exploit this dual functionalization tactic to elaborate the relative role of attached moieties in the affinity interaction of CNTs with extra-cellular sialic acid, a biological target showing metastatic stage-dependent over-expression in colon cancer cells.

Adsorption of water and n-hexane on pristine and oxidized carbon nanotube supports of cobalt-based Fischer–Tropsch catalysts

Adsorption of water and n-hexane by oxidized and pristine CNTs at different stages of Co/CNT catalyst preparation has been studied to reveal the effect of the support surface functionalization on the catalyst selectivity in Fischer–Tropsch synthesis.

Magnetic graphene oxide-nano zero valent iron (GO–nZVI) nanohybrids synthesized using biocompatible cross-linkers for methylene blue removal

A green synthesis method was used to prepare GO–nZVI nanohybrids to provide an adsorbent with high adsorption efficiency that can be removed from aqueous solutions easily by magnetic separation.

Kinetics of the defunctionalization of oxidized few-layer graphene nanoflakes

Thermal defunctionalization of oxidized jellyfish-like few-layer graphene nanoflakes was studied under non-isothermal conditions by simultaneous thermal analysis. Activation energies for thermal decomposition of different oxygen functional groups were calculated by the Kissinger method and compared with those for oxidized carbon nanotubes. Oxygen content in graphene nanoflakes was found to significantly affect the decomposition activation energies of carboxylic and keto/hydroxy acids because of their acceptor properties and strong distortion of the graphene layers at the edges of the nanoflakes. The structure of the carbon material and the oxygen chemical state significantly influence the decomposition kinetics of thermally stable oxygen-containing groups. The activation energy for thermal decomposition of phenol groups (110-150 kJ mol^-1) is close to that for graphene oxide reduction.

3D Frameworks with Variable Magnetic and Electrical Features from Sintered Cobalt-Modified Carbon Nanotubes

3D frameworks of carbon nanotubes (CNTs) uniformly decorated by cobalt oxide or carbon-encapsulated cobalt nanoparticles were obtained by spark plasma sintering for the first time. The influence of the sintering temperature ( T_S) and Co content on the morphology, structure, and electrical and magnetic properties of the obtained materials was investigated by Raman spectroscopy, electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and in situ magnetometry. It was shown that application of the SPS technique allowed simultaneous compaction of the material, formation of CNT framework, and Co oxide reduction. The appearance of the carbon shell around 4-10 nm Co particles was observed at T_S > 600 °C. At higher T_S, the Co particle size increased (up to 300 nm at 1400 °C), whereas the carbon shell ordered and thickened. The formation of large-size few-layers graphene sheets was observed at T_S = 1400 °C. Electrical conductivity of the composites was found to be higher than that of sintered pristine CNTs and varied in the range of 500-12 500 Sm/m. Magnetic experiments demonstrated soft magnetization of the samples and the coercivity of 200-300 Oe. Thus, the obtained CNT-based material is simultaneously compact, formable, electroconductive, and ferromagnetic. Its properties can be tuned by variation of the sintering parameters. Synthesized cobalt-modified carbon 3D structures are promising for the application in magnetic separation, catalysis, fuel cells, and electromagnetic shielding.

Shaping nanofiltration channels in a carbonaceous membrane via controlling the pyrolysis atmosphere

Pyrolysis of a comb-like copolymer towards formation of more disordered graphene species and small graphitic domains.