Flexible digital signal processing architecture for narrowband and spread-spectrum lock-in detection in multiphoton microscopy and time-resolved spectroscopy

New directional spectral emissivity measurement apparatus simultaneously collecting the blackbody and sample radiation

A new apparatus simultaneously and rapidly measuring the sample radiation and the blackbody radiation by one detector without moving any experimental component is designed to measure the directional spectral emissivity of solid samples in a controlled environment. The effect of multiple reflections in the sample chamber on the measurement result is evaluated. The temperature distribution of the sample surface is measured by using a thermal imager. In order to validate the experimental apparatus, the directional spectral emissivity of silicon is measured in a nitrogen environment and that of iron is measured in vacuum, and the normal spectral emissivity of pure copper is measured during the oxidation process. Good agreement between the measured results and the reported data proves the reliability of the designed apparatus. The expanded uncertainty of the measurement system is estimated to be less than 5.3% when the emission angle is 86°.

DR-RINS: Digital real-time relative intensity noise suppressor for pump-probe spectroscopy and microscopy

Relative intensity noise (RIN) inherent in fiber lasers poses a serious obstacle to their use in pump-probe spectroscopy and imaging. RIN can be removed through an analog balanced detector, or, as we have previously shown, software adaptive noise cancellation (ANC) on digitized signals. One major drawback to software ANC is the added time required for digitizing and post-processing. In this article, we describe a design for ANC on a field-programmable gate array (FPGA), making use of high-level synthesis tools and fixed-point arithmetic to achieve real-time laser RIN suppression at 25 MHz sample rates. Unlike the software-ANC approach, the FPGA-ANC device can serve as a dedicated drop-in denoiser, placed between the detectors and a commercial lock-in amplifier. We demonstrate its application to transient absorption spectroscopy and microscopy, lowering the noise floor to ∼17 dB above the shot noise limit. Furthermore, we demonstrate a dramatic improvement in data acquisition time from ∼6 h to ∼5 min in a real-time imaging scenario.

Leaving the Limits of Linearity for Light Microscopy

Nonlinear microscopy has enabled additional modalities for chemical contrast, deep penetration into biological tissues, and the ability to collect dynamics on ultrafast timescales across heterogenous samples. The additional light fields introduced to a sample offer seemingly endless possibilities for variation to optimize and customize experimentation and the extraction of physical insight. This perspective highlights three areas of growth in this diverse field: the collection of information across multiple timescales, the selective imaging of interfacial chemistry, and the exploitation of quantum behavior for future imaging directions. Future innovations will leverage the work of the studies reviewed here as well as address the current challenges presented.

Adaptive noise canceling for transient absorption microscopy

SIGNIFICANCE

Ultrafast fiber lasers are an attractive alternative to bulk lasers for nonlinear optical microscopy for their compactness and low cost. The high relative intensity noise (RIN) of these lasers poses a challenge for pump-probe measurements such as transient absorption and stimulated Raman scattering, along with modalities that provide label-free contrast from the vibrational and electronic structure of molecules.

AIM

Digital adaptive filtering was applied to determine the applicability for canceling laser RIN in a transient absorption microscope with an ultrafast fiber laser source.

APPROACH

Digitized signals from the transmitted probe and reference photodetectors were fed to an adaptive filter in MATLAB, running in a noise canceling configuration. This result was then fed to a software lock-in algorithm to demodulate the pump-probe signal. Images were built up one line scan at a time with a 3.5-kHz resonant scanner, with 100  ×   averaging. The imaging target was Bi4Ge3O12, which exhibits nondegenerate two-photon absorption at the pump/probe wavelengths used (530-nm pump and 490-nm probe).

RESULTS

Without adaptive noise cancellation, the lock-in output primarily passes the laser RIN within its detection bandwidth, resulting in images that closely follow the linear transmissivity and lack sensitivity to pump-probe time delay. With adaptive noise cancellation in front of the lock-in, the RIN rejection is enough to restore the z-sectioning and sensitivity to pump-probe delay, as expected for transient absorption. Results were limited primarily by noise from the photodetector and analog-to-digital converter.

CONCLUSIONS

Digital adaptive noise cancellation, even when limited by electronics noise, can recover pump-probe signals by removal of laser RIN, under conditions where averaging alone fails.

Invited Review Article: Pump-probe microscopy

Multiphoton microscopy has rapidly gained popularity in biomedical imaging and materials science because of its ability to provide three-dimensional images at high spatial and temporal resolution even in optically scattering environments. Currently the majority of commercial and home-built devices are based on two-photon fluorescence and harmonic generation contrast. These two contrast mechanisms are relatively easy to measure but can access only a limited range of endogenous targets. Recent developments in fast laser pulse generation, pulse shaping, and detection technology have made accessible a wide range of optical contrasts that utilize multiple pulses of different colors. Molecular excitation with multiple pulses offers a large number of adjustable parameters. For example, in two-pulse pump-probe microscopy, one can vary the wavelength of each excitation pulse, the detection wavelength, the timing between the excitation pulses, and the detection gating window after excitation. Such a large parameter space can provide much greater molecular specificity than existing single-color techniques and allow for structural and functional imaging without the need for exogenous dyes and labels, which might interfere with the system under study. In this review, we provide a tutorial overview, covering principles of pump-probe microscopy and experimental setup, challenges associated with signal detection and data processing, and an overview of applications.