Photocatalytic reduction of Cr(VI) and Ni(II) in aqueous solution by synthesized nanoparticle ZnO under ultraviolet light irradiation: a kinetic study

Enhanced photoreduction efficiency of Cr(VI) driven by visible light in a new Zr-based metal-organic framework modified by hydroxyl groups

While metal-organic framework (MOF) photocatalysts have demonstrated a unique Cr(VI) photoreduction capability in recent decades, their performance is still insufficient for practical applications because of their low Cr(VI) uptake and poor visible light response. To cope with these drawbacks, a new OH-modified Zr-based MOF, termed HCMUE-1, was successfully prepared via a solvothermal method in this work. The complete characterization of HCMUE-1 was performed through various techniques, including powder X-ray diffraction (PXRD), Raman spectroscopy, Fourier transform infrared (FT-IR), thermogravimetric analysis and differential scanning calorimetry (TGA-DSC), scanning electron microscopy combined with energy-dispersive X-ray (SEM-EDX), and X-ray photoelectron spectroscopy (XPS). The obtained data exhibited the excellent Cr(VI) photoreduction efficiency of HCMUE-1, reaching up to 98% after 90 min and almost 100% after 120 min under visible light illumination in a low acidic medium. Noteworthily, HCMUE-1 retained the same Cr(VI) removal rate for at least seven cycles without considerable loss. Further experimental investigations demonstrated that the structural stability and surface morphology of HCMUE-1 were retained after photoreduction. Moreover, the photocatalytic reduction mechanism of Cr(VI) to Cr(III) was interpreted through a series of systematic experimental measurements. These results indicate that HCMUE-1 possesses potential as an efficient photocatalyst for reducing toxic Cr(VI) species from wastewater in real-life conditions.

Bacteria-driven copper redox reaction coupled electron transfer from Cr(VI) to Cr(III): A new and alternate mechanism of Cr(VI) bioreduction

Cr(VI) released into the environment inevitably co-exists with other contaminants, such as heavy metal ions, thus altering the performance of bacteria for Cr(VI) reduction; however, the mechanism underlying Cr(VI)-reducing bacterial response to heavy metal ions remains elusive. Herein, we investigate the toxic effects of Cu(II) and Cr(VI) on Cr(VI)-reducing bacterium Pannonibacter phragmitetus D-6 (hereafter D-6), which changes the primary metabolic pattern of Cr(VI). At Cu(II) concentrations of 10-100 mg/L, the efficiency of Cr(VI) reduction increases significantly. The co-exposure of Cr(VI) and Cu(II) induces D-6 to preferentially respond to Cu(II) through electrostatic forces, which is then reduced to Cu(I) outside and inside the bacterial cells. The original pathways for Cr(VI) reduction are weakened via downregulating genes related to Cr(VI) transport and reduction. A new mechanism involving Cu(II)-mediated electron transfer from D-6 to Cr(VI) is elucidated. Specially, Cu(II) accumulates around the cells as an electron shuttle and promotes Cr(VI) reduction. Genes encoding cytochromes involved in electron transfer are significantly up-regulated, thus promoting Cu(II) reduction. The Cu(II)/Cu(I) redox cycle ensures the continuous bioremoval of Cr(VI) in a cycle test. This study reveals an overlooked mechanism for Cr(VI) reduction, which provides theoretical guidance for designing practical microbial process to remediate Cr(VI) contamination.

Versatile application of BiVO4/TiO2 S-scheme photocatalyst: Photocatalytic CO2 and Cr(VI) reduction

Herein, the synthesis, characterization, and reduction properties of 2D TiO₂ aerogel powder decorated with BiVO₄ (TiO₂/BiVO₄) were investigated for versatile applications. First, 2D TiO₂ was prepared via lyophilization and subsequently modified with BiVO₄ using a wet impregnation method. The morphology, structure, composition, and optical properties were evaluated using transmission electron microscopy (TEM), X-ray diffractometry (XRD), laser-induced breakdown spectroscopy (LIBS), and diffuse reflectance spectroscopy (DRS), respectively. Significantly enhanced photocurrent densities (by 3-15 times) were obtained for TiO₂/BiVO₄ compared to those of pure TiO₂ and BiVO₄. The reduction of toxic Cr(VI) to Cr(III) was assessed, including the effect of pH on overall photocatalytic efficiency. Under acidic conditions (pH ∼ 2), Cr(VI) reduction efficiency reached 100% within 2 h. For photocatalytic CO₂ reduction, the highest yields of CH₄ and CO were obtained using TiO₂/BiVO₄. A higher efficiency for both applications was achieved because of the better separation of the electron-hole pairs in TiO₂/BiVO₄. The excellent stability of TiO₂/BiVO₄ over repeated runs highlights its potential for use in versatile environmental applications. The efficiency of TiO₂/BiVO₄ is due to the interplay of the structure, morphology, composition, and photoelectrochemical properties that favour the material for the presented herein photocatalytic applications.

The interaction of ZnO nanoparticles, Cr(VI), and microorganisms triggers a novel ROS scavenging strategy to inhibit microbial Cr(VI) reduction

Cr(VI) contaminated water usually contains other contaminants like engineered nanomaterials (ENMs). During the process of microbial treatment, the inevitable interaction of Cr(VI), ENMs, and microorganisms probably determines the efficiency of Cr(VI) biotransformation, however, the corresponding information remains elusive. This study investigated the interaction of ZnO nanoparticles (NPs), Cr(VI), and Pannonibacter phragmitetus BB (hereafter BB), which changed the process of microbial Cr(VI) reduction. ZnO NPs inhibited Cr(VI) reduction, but had no effect on bacterial viability. In particular, Cr(VI) induced BB to produce organic acids and to drive Zn²⁺ dissolution from ZnO NPs inside and outside of cells. The dissolved Zn²⁺ not only promoted Cr(VI) reduction to Cr(V)/Cr(IV) by strengthening sugar metabolism and inducing increase in NAD(P)H production, but also hindered Cr(V)/Cr(IV) transformation to Cr(III) through down-regulating Cr(VI) reductase genes. A novel bacterial driven ROS scavenging mechanism leading to the inhibition of Cr(VI) reduction was elucidated. Specifically, the accumulated Cr(VI) and Cr(V)/Cr(IV) formed a redox dynamic equilibrium, which triggered the disproportionation of superoxide radicals mimicking superoxide dismutase through the flip-flop of Cr(VI) and Cr(V)/Cr(IV) in bacterial cells. This study provided a realistic insight into design the applicability of biological remediation technology for Cr(VI) contaminant and evaluating environmental risks of ENMs.

Enhanced Solar Photocatalytic Activity of Thermally Stable I:ZnO/Glass Beads for Reduction of Cr(VI) in Tannery Effluent

Chromium (VI) in tannery effluent is one of the major environmental concerns for the environmentalists due to the hazardous nature of Cr(VI) ions. To reduce Cr(VI) to Cr(III) as an innocuous moiety, pure and I-doped ZnO was grafted over the etched surface of glass beads by successive ionic layer adsorption and reaction (SILAR). Powdered, pure, and I-doped ZnO scrapped from the surface of glass beads was characterized for crystallinity, morphology, and elemental composition by XRD, SEM, TEM, and EDX. The optical properties of both photocatalysts revealed that owing to optimized iodine doping of ZnO, reduction in the bandgap was observed from 3.3 to 2.9 eV. The crystalline nano-bricks of I:ZnO adhered to glass beads were investigated to have remarkable capability to harvest sunlight in comparison to intrinsic ZnO nanodiscs. The thermal stability of I:ZnO was also found to be much improved due to doping of ZnO. The photocatalytic activities of ZnO/GB and I:ZnO/GB were compared by extent of reduction of Cr(VI) under direct natural sunlight (600–650 KWh/m2). The disappearance of absorbance peaks associated with Cr(VI) after treatment with I:ZnO/GB confirmed higher photocatalytic activity of I:ZnO/GB. The reaction parameters of solar photocatalytic reduction, i.e., initial pH (5–9), initial concentration of Cr(VI) (10–50 ppm), and solar irradiation time (1–5 h) were optimized using response surface methodology. The solar photocatalytic reduction of Cr(VI) to Cr(III) present in real tannery effluent was examined to be 87 and 98%, respectively, by employing ZnO/GB and I:ZnO/GB as solar photocatalysts. The extent of reduction was also confirmed by complexation of Cr(VI) and Cr(III) present in treated and untreated tannery waste with 1, 5-diphenylcarbazide. The results of AAS and UV/vis spectroscopy for the decrease in concentration of Cr also supported the evidence of higher efficiency of I:ZnO/GB for reduction of Cr(VI) in tannery effluent. Reusability of the fabricated photocatalyst was assessed for eight cycles, and magnificent extent of reduction of Cr(VI) indicated its high efficiency. Conclusively, I:ZnO/GB is a potential and cost-effective candidate for Cr(VI) reduction in tannery effluent under natural sunlight.

Synthesis, structural, and opto-electrochemical properties of cobalt aluminate type spinel and its use with ZnO for Cr(VI) photoreduction

The discovery of the occurrence of inorganic pollutants in surface waters is identified in the system assessment quality. The most harmful elements are pesticides, persistent organic pollutants, pharmaceuticals, personal care products, and heavy metals are still dangerous to the environment due to their general uses. Chromate has the largest concentration compared to the other metals in the wastewater industries. This work evaluates the application of the spinel p-CoAl₂O₄ as a photocatalyst prepared by the nitrate synthesis process to reduce Cr(VI), a hazardous metal for the environment. The photocatalyst was characterized using thermal analysis (TG), X-ray diffraction, UV-diffuse reflectance spectroscopy, scanning electron microscopy, fluorescent X-ray, Fourier transform infrared spectroscopy, electrical conductivity, and photoelectrochemically. The results showed that the efficiency of optimum reduction of Cr(Vl) to Cr(IIl) photoreduction is more effective (77%) for pH = 3.6 than that at high pH values up to 8 (7%). Moreover, the effect of the hetero-system CoAl₂O₄/ZnO on photocatalytic efficiency was investigated. The photocatalytic activity increases up to 99% with 1 g L^-1, a total catalyst dosage over the hetero-system CoAl₂O₄/ZnO at a ratio of 75%/25%. This data is better relative to CoAl₂O₄ or ZnO alone. The Cr(VI) photoreduction activity improvement was caused by the best separation and the photogeneration of electron-hole on the CoAl₂O₄/ZnO surfaces. Finally, the Lagergren pseudo-first-order and the Langmuir-Hinshelwood models fit well the experimental kinetics.

Highly Efficient Removal of Cu(II) Ions from Acidic Aqueous Solution Using ZnO Nanoparticles as Nano-Adsorbents

Water pollution by heavy metals has significant effects on aquatic ecosystems. Copper is one of the heavy metals that can cause environmental pollution and toxic effects in natural waters. This encourages the development of better technological alternatives for the removal of this pollutant. This work explores the application of ZnO nanoparticles (ZnO-NPs) for the removal of Cu(II) ions from acidic waters. ZnO NPs were characterized and adsorption experiments were performed under different acidic pHs to evaluate the removal of Cu(II) ions with ZnO NPs. The ZnO NPs were chemically stable under acidic conditions. The adsorption capacity of ZnO NPs for Cu(II) was up to 47.5 and 40.2 mg·g−1 at pH 4.8 and pH 4.0, respectively. The results revealed that qmax (47.5 mg·g−1) and maximum removal efficiency of Cu(II) (98.4%) are achieved at pH = 4.8. In addition, the surface roughness of ZnO NPs decreases approximately 70% after adsorption of Cu(II) at pH 4. The Cu(II) adsorption behavior was more adequately explained by Temkin isotherm model. Additionally, adsorption kinetics were efficiently explained with the pseudo-second-order kinetic model. These results show that ZnO NPs can be an efficient alternative for the removal of Cu(II) from acidic waters and the adsorption process was more efficient under pH = 4.8. This study provides new information about the potential application of ZnO NPs as an effective adsorbent for the remediation and treatment of acidic waters contaminated with Cu(II).

Application of Bi12ZnO20 Sillenite as an Efficient Photocatalyst for Wastewater Treatment: Removal of Both Organic and Inorganic Compounds

This work aims to synthesize and characterize a material that can be used as an effective catalyst for photocatalytic application to remove both organic and inorganic compounds from wastewater. In this context, sillenite Bi12ZnO20 (BZO) in a pure phase was synthesized using the sol-gel method. Before calcination, differential scanning calorimetry (DSC) analysis was done to determine the temperature of the formation of the sillenite phase, which was found to be 800 °C. After calcination, the phase was identified by X-ray diffraction (XRD) and then refined using the Rietveld refinement technique. The results prove that BZO crystals have a cubic symmetry with the space group I23 (N°197); the lattice parameters of the structure were also determined. From the crystalline size, the surface area was estimated using the Brunauer-Emmett-Teller (BET) method, which was found to be 11.22 m2/g. The formation of sillenite was also checked using the Raman technique. The morphology of the crystals was visualized using electron scanning microscope (SEM) analysis. After that, the optical properties of BZO were investigated by diffuse reflectance spectroscopy (DRS) and photoluminescence (PL); an optical gap of 2.9 eV was found. In the final step, the photocatalytic activity of the BZO crystals was evaluated for the removal of inorganic and organic pollutants, namely hexavalent chromium Cr(VI) and Cefixime (CFX). An efficient removal rate was achieved for both contaminants within only 3 h, with a 94.34% degradation rate for CFX and a 77.19% reduction rate for Cr(VI). Additionally, a kinetic study was carried out using a first-order model, and the results showed that the kinetic properties are compatible with this model. According to these findings, we can conclude that the sillenite BZO can be used as an efficient photocatalyst for wastewater treatment by eliminating both organic and inorganic compounds.

Formic acid motivated photocatalytic reduction of Cr(VI) to Cr(III) with ZnFe2O4 nanoparticles under UV irradiation

UV-light irradiated photocatalytic reduction of Cr(VI) to Cr(III) in aqueous solution using ZnFe₂O₄ nanoparticles in the presence of formic acid was reported. X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and UV-Vis diffuse reflectance spectroscopy (DRS) were employed to characterize ZnFe₂O₄ nanoparticles. The photocatalytic activity of pure ZnFe₂O₄ under UV irradiation was significantly low. However, the Cr(VI) reduction efficiency on nano-sized ZnFe₂O₄ in the presence of 0.40% formic acid reached 95.4% within 4 h. Herein, the effect of pH, photocatalyst amount, initial concentration of Cr(VI) and formic acid concentration on the photocatalytic reduction of Cr(VI) was investigated. The results indicated that the photocatalytic reduction of Cr(VI) decreased with increase in the initial concentration of Cr(VI), photocatalyst dosage and pH. The reduction rate constant declined from 0.017 min^-1 to 0.0023 min^-1 with the increase in initial concentration of Cr(VI) from 5 to 25 mg L^-1. However, the reduction rate constant sharply increased from 0.000075 min^-1 to 0.0127 min^-1 with the increase in formic acid concentration from 0.05% to 0.40%. The formic acid could capture the photogenerated holes, and eventually formate (HCOO^-) ions could be converted into carbon dioxide radicals (•CO₂^-). Because of more negative redox potential for •CO₂^- radicals, Cr(VI) species could easily be reduced to Cr(III) under UV irradiation. The pseudo-first-order kinetic reaction was confirmed for this reduction process. A tenable mechanism for the photocatalytic Cr(VI) reduction has also been demonstrated.

Electrospun cationic nanofiber membranes for adsorption and determination of Cr(vi) in aqueous solution: adsorption characteristics and discoloration mechanisms

In this study, a novel cationic nanofiber membrane with various functional groups, good structural stability, and high adsorption capacity of Cr(vi) is presented. This nanofiber membrane is prepared by electrospinning a mixed aqueous solution of a cationic polycondensate (CP) and polyvinyl alcohol (PVA). With the aid of PVA, CP can be smoothly electrospun without using any organic solvents, and the cross-linking between CP and PVA improves the stability of membrane in acidic solution. Chemical and morphology characterization reveals that the CP/PVA membrane is composed of interwoven nanofibers that contain numerous cationic groups. Due to its high cationicity and hydrophilicity, the CP/PVA membrane shows great affinity for HCr₂O₇⁻ and Cr₂O₇²⁻. Adsorption experiments indicate that the CP/PVA membrane can remove Cr(vi) from simulated wastewater rapidly and efficiently in both batch and continuous mode. Besides, the presence of most coexisting ions will not interfere with the adsorption. Due to the redox reaction between the CP/PVA membrane and adsorbed Cr(vi), the CP/PVA membrane exhibits distinct color change after Cr(vi) adsorption and the discoloration is highly dependent on the adsorption amount. Therefore, in addition to serving as a highly efficient adsorbent, the CP/PVA membrane is also expected to be a convenient and low-cost method for semi-quantitative determination of Cr(vi) in wastewater.

Cationic nanofiber membranes are prepared by electrospinning mixed aqueous solution of a cationic polycondensate (CP) and PVA. Apart from being a highly efficient Cr(vi) adsorbent, it can also serve as a convenient method for Cr(vi) determination.

Adsorptive of Nickel in Wastewater by Olive Stone Waste: Optimization through Multi-Response Surface Methodology Using Desirability Functions

Pollution from industrial wastewater has the greatest impact on the environment due to the wide variety of wastes and materials that water can contain. These include heavy metals. Some of the technologies that are used to remove heavy metals from industrial effluents are inadequate, because they cannot reduce their concentration of the former to below the discharge limits. Biosorption technology has demonstrated its potential in recent years as an alternative for this type of application. This paper examines the biosorption process for the removal of nickel ions that are present in wastewater using olive stone waste as the biosorbent. Kinetic studies were conducted to investigate the biosorbent dosage, pH of the solution, and stirring speed. These are input variables that are frequently used to determine the efficiency of the adsorption process. This paper describes an effort to identify regression models, in which the biosorption process variables are related to the process output (i.e., the removal efficiency). It uses the Response Surface Method (RSM) and it is based on Box Benken Design experiments (BBD), in which olive stones serves as the biosorbent. Several scenarios of biosorption were proposed and demonstrated by use of the Multi-Response Surface (MRS) and desirability functions. The optimum conditions that were necessary to remove nickel when the dosage of biosorbent was the minimum (0.553 g/L) were determined to be a stirring speed of 199.234 rpm and a pH of 6.369. The maximum removal of nickel under optimized conditions was 61.73%. Therefore, the olive stone waste that was investigated has the potential to provide an inexpensive biosorbent material for use in recovering the water that the nickel has contaminated. The experimental results agree closely with what the regression models have provided. This confirms the use of MRS since this technique and enables satisfactory predictions with use of the least possible amount of experimental data.

Application of ZnO nanorods doped with Cu for enhanced sonocatalytic removal of Cr(VI) from aqueous solutions

The aim of this research was to develop a simple and inexpensive process for reduction of Cr(VI) to Cr(III). Zinc oxide nanoparticles were synthesized with an easy co-precipitation procedure, and the addition of Cu²⁺ doping agent effectively enhanced the Cr(VI) reduction in the presence of ultrasound (US). XRD, FT-IR, FE-SEM, EDX, VSM, and XPS were used to determine the structural specifications of the zinc oxide nanoparticles. Under optimal conditions such as pH 3, initial Cr(VI) content of 20 mg/L, and catalyst dosage of 0.8 g/L, the ultrasonic/Cu-ZnO process showed a higher sonocatalytic activity (96.83%) than ultrasonic/ZnO (67.36%) after 60 min. By increasing pH and Cr(VI) concentration, the removal efficacy of Cr(VI) declined. The experimental data was well described with the first-order kinetic model. When initial Cr(VI) concentration increased from 10 to 50 mg/L, the first-order rate constant declined from 0.2326 to 0.0019 min^-1 and electrical energy per order (E_EO) enhanced from 19.81 to 2425.26 kWh/m³. Also, the ultrasonic/Cu-ZnO system exhibited considerable sonocatalytic performance in Cr(VI) reduction in the presence of hydrogen peroxide and citric acid, and complete removal was achieved within 60 min. The presence of anions negatively affected Cr(VI) reduction. Complete reduction was attained when ultrasound was applied at a power of 100 W. The catalyst activity was well maintained up to six consecutive cycles. In addition, the removal efficiency was approximately 62 and 65% for field water and real electroplating wastewater samples, respectively.

Mechanisms of removal of heavy metal ions by ZnO particles

Effluent discharges from industry and domestic waste containing unknown inorganic pollutants. In this work, different mechanisms of heavy metal ions removal using ZnO particles were studied. ZnO particles were synthesized using solid precipitation technique. The morphology of ZnO particles was rod-like shape. The average length and diameter of ZnO particle were 497.34 ± 15.55 and 75.78 ± 10.39nm, respectively. These particles removed effectively heavy metal ions such as Cu(II), Ag(I) and Pb(II) ions with efficiency >85% under exposure of 1 hour of UV light. However, poor removal efficiency, i.e. <15% was observed for Cr(VI), Mn(II), Cd(II) and Ni(II) ions. The removal of these heavy metal ions was in the forms of metals or metal oxide via reduction/oxidation or adsorption mechanism.

Microwave synthesis of ZnIn2S4/WS2 composites for photocatalytic hydrogen production and hexavalent chromium reduction

A rapid microwave synthesis route for the fabrication of ZnIn₂S₄ powder and ZnIn₂S₄/WS₂ composites is presented.

Enhancement of photocatalytic activity of Cu-doped ZnO nanorods for the degradation of an insecticide: Kinetics and reaction pathways

The photocatalytic degradation of organophosphorus pesticide such as diazinon was investigated by Cu-doped ZnO nanorods. Cu-doped ZnO nanorods were synthesized via a facile co-precipitation method. The catalyst was characterized by XRD, FESEM, EDX, VSM, XPS, and pH_zpc techniques. The effects of some operational parameters such as solution pH, Cu-doped ZnO nanorods dosage, initial diazinon concentration, oxygen and nitrogen gases, H₂O₂ concentration, and type of organic compounds on the degradation efficiency were discussed through the photocatalytic experiments using the Cu-doped ZnO nanorods. Neutral pH was selected as an optimal pH condition due to a photo-corrosion of ZnO in acidic and basic conditions. As the Cu-doped ZnO nanorods dosage increased up to 0.2 g/L, degradation efficiency of diazinon was continuously enhanced. Pseudo-first-order rate constant (k_obs) was decreased from 0.051 to 0.0052 min^-1 and electrical energy per order (E_Eo) was increased from 94.12 to 923.08 (kWh/m³) by increasing diazinon concentration from 10 to 50 mg/L, respectively. The efficiency of the UV/Cu-doped ZnO for diazinon removal was approximately 96.97%, which was more effective than the UV/ZnO process (58.52%). Photocatalytic activity was maintained even after five successive cycles.

Adsorptive removal of nickel(II) ions from aqueous environment: A review

Among various methods adsorption can be efficiently employed for the treatment of heavy metal ions contaminated wastewater. In this context the authors reviewed variety of adsorbents used by various researchers for the removal of nickel(II) ions from aqueous environment. One of the objectives of this review article is to assemble the scattered available enlightenment on a wide range of potentially effective adsorbents for nickel(II) ions removal. This work critically assessed existing knowledge and research on the uptake of nickel by various adsorbents such as activated carbon, non-conventional low-cost materials, nanomaterials, composites and nanocomposites. The system's performance is evaluated with respect to the overall metal removal and the adsorption capacity. In addition, the equilibrium adsorption isotherms, kinetics and thermodynamics data as well as various optimal experimental conditions (solution pH, equilibrium contact time and dosage of adsorbent) of different adsorbents towards Ni(II) ions were also analyzed. It is evident from a literature survey of more than 190 published articles that agricultural solid waste materials, natural materials and biosorbents have demonstrated outstanding adsorption capabilities for Ni(II) ions.

Fabrication of Unique Magnetic Bionanocomposite for Highly Efficient Removal of Hexavalent Chromium from Water

Biotreatment of hexavalent chromium has attracted widespread interest due to its cost effective and environmental friendliness. However, the difficult separation of biomass from aqueous solution and the slow hexavalent chromium bioreduction rate are bottlenecks for biotechnology application. In this approach, a core-shell structured functional polymer coated magnetic nanocomposite was prepared for enriching the hexavalent chromium. Then the nanocomposite was connected to the bacteria via amines on bacterial (Bacillus subtilis ATCC-6633) surface. Under optimal conditions, a series of experiments were launched to degrade hexavalent chromium from the aqueous solution using the as-prepared bionanocomposite. Results showed that B. subtilis@Fe3O4@mSiO2@MANHE (BFSM) can degrade hexavalent chromium from the water more effectively (a respectable degradation efficiency of about 94%) when compared with pristine B. subtilis and Fe3O4@mSiO2@MANHE (FSM). Moreover, the BFSM could be separated from the wastewater by magnetic separation technology conveniently due to the Fe3O4 core of FSM. These results indicate that the application of BFSM is a promising strategy for effective treating wastewater containing hexavalent chromium.

Photocatalytic activity and reusability of ZnO layer synthesised by electrolysis, hydrogen peroxide and heat treatment

In this study, the zinc oxide (ZnO) layer was synthesised on the surface of Zn plates by three different techniques, i.e. electrolysis, hydrogen peroxide and heat treatment. The synthesised ZnO layers were characterised using scanning electron microscopy, X-ray diffraction, UV-visible diffuse reflectance and photoluminescence spectroscopy. The photocatalytic activity of the ZnO layer was further assessed against methylene blue (MB) degradation under UV irradiation. The photocatalytic degradation of MB was achieved up to 84%, 79% and 65% within 1 h for ZnO layers synthesised by electrolysis, heat and hydrogen peroxide treatment, respectively. The reusability results show that electrolysis and heat-treated ZnO layers have considerable photocatalytic stability. Furthermore, the results confirmed that the photocatalytic efficiency of ZnO was directly associated with the thickness and enlarged surface area of the layer. Finally, this study proved that the ZnO layers synthesised by electrolysis and heat treatment had shown better operational stability and reusability.

A novel Ag deposited nanocoordination polymer derived porous SnO2/NiO heteronanostructure for the enhanced photocatalytic reduction of Cr(vi) under visible light

A novel silver deposited SnO₂/NiO heteronanostructure is prepared and applied for the photocatalytic reduction of toxic aqueous Cr(vi) under visible light conditions.

ZnO-PLLA nanofiber nanocomposite for continuous flow mode purification of water from Cr(VI)

Nanomaterials of ZnO-PLLA nanofibers have been used for the adsorption of Cr(VI) as a prime step for the purification of water. The fabrication and application of the flexible ZnO-PLLA nanofiber nanocomposite as functional materials in this well-developed architecture have been achieved by growing ZnO nanorod arrays by chemical bath deposition on synthesized electrospun poly-L-lactide nanofibers. The nanocomposite material has been tested for the removal and regeneration of Cr(IV) in aqueous solution under a “continuous flow mode” by studying the effects of pH, contact time, and desorption steps. The adsorption of Cr(VI) species in solution was greatly dependent upon pH. SEM micrographs confirmed the successful fabrication of the ZnO-PLLA nanofiber nanocomposite. The adsorption and desorption of Cr(VI) species were more likely due to the electrostatic interaction between ZnO and Cr(VI) ions as a function of pH. The adsorption and desorption experiments utilizing the ZnO-PLLA nanofiber nanocomposite have appeared to be an effective nanocomposite in the removal and regeneration of Cr(VI) species.

Photocatalytic reduction of hexavalent chromium with illuminated amorphous FeOOH

In this study, photocatalytic reduction of hexavalent chromium [Cr(VI)] by amorphous FeOOH was investigated with variations in FeOOH dosage, pH, initial Cr(VI) concentration, purging gas, organic compounds and initial hydrogen peroxide concentration. Reduction and adsorption were identified as important processes for the removal of Cr(VI). FeOOH dosage was also an important parameter for the removal of Cr(VI). As the FeOOH dosage increased up to 0.5 g/L, the removal of Cr(VI) was continuously enhanced and then decreased above 0.5 g/L due to increased blockage of the incident UV light. The removal efficiency of Cr(VI) decreased with increasing pH, initial Cr(VI) concentration and initial hydrogen peroxide concentration. While the removal efficiency of Cr(VI) increased with purging of nitrogen gas compared to that of oxygen gas because of less competition between dissolved oxygen and Cr(VI) with the electron in the conduction band of FeOOH. The photocatalytic reduction of Cr(VI) was increased in the presence of citric acid and phenol, while it was decreased in the presence of EDTA and oxalic acid. The reaction rate constant (kobs) was decreased from 0.2141 to 0.0026 1/min and the value of electrical energy per order (EEo) was increased from 22.41 to 1846.15 (kWh/m3) with increasing initial Cr(VI) concentration from 10 to 50 mg/L, respectively. Finally, proper photocatalytic activity was maintained even after five successive cycles.

Facile synthesis of porous single crystalline ZnO nanoplates and their application in photocatalytic reduction of Cr(VI) in the presence of phenol

Porous single crystalline ZnO nanoplates were successfully synthesized through a facile and cost-effective hydrothermal process at low temperature condition, followed by annealing of the zinc carbonate hydroxide hydrate precursors. The as-prepared products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) measurements. The porous single crystalline ZnO nanoplates are with 12nm thickness and pore ranging from 10nm to several tens of nanometers. The porous structure of the ZnO nanoplates caused large amount of surface defects which worked as photogenerated holes' shallow trappers and largely restrained the recombination of photogenerated electrons and holes, resulting in a significantly high photocatalytic activity and durability toward the photoreduction of Cr(VI) under UV irradiation. Moreover, a synergistic effect, that is, increased photocatalytic reduction of Cr(VI) and degradation of phenol, can be observed. Furthermore, the synergistic photocatalytic mechanism has also been discussed. Those results present an enlightenment to employ porous single crystalline nanomaterials to remove Cr(VI) and organic pollutants simultaneously.

Impact of humic/fulvic acid on the removal of heavy metals from aqueous solutions using nanomaterials: a review

Nowadays nanomaterials have been widely used to remove heavy metals from water/wastewater due to their large surface area and high reactivity. Humic acid (HA) and fulvic acid (FA) exist ubiquitously in aquatic environments and have a variety of functional groups which allow them to complex with metal ions and interact with nanomaterials. These interactions can not only alter the environmental behavior of nanomaterials, but also influence the removal and transportation of heavy metals by nanomaterials. Thus, the interactions and the underlying mechanisms involved warrant specific investigations. This review outlined the effects of HA/FA on the removal of heavy metals from aqueous solutions by various nanomaterials, mainly including carbon-based nanomaterials, iron-based nanomaterials and photocatalytic nanomaterials. Moreover, mechanisms involved in the interactions were discussed and potential environmental implications of HA/FA to nanomaterials and heavy metals were evaluated.

Effect of organic matter on cyanide removal by illuminated titanium dioxide or zinc oxide nanoparticles

Effect of different type of organic compounds (humic acid, oxalate, ethylenediaminetetraacetic acid, nitrilotriacetic acid, phenol) on the photocatalytic removal of cyanide with TiO2 or ZnO was studied in this work with variation of the solution pH, contact time, initial cyanide concentration and type of organic compounds. Photocatalytic oxidation efficiency of cyanide with TiO2 was greatly affected by the solution pH. It increased as the solution pH decreased. Also maximum removal of cyanide by ZnO was observed near at neutral pH because of the reduced photocatalytic activity of ZnO at exceedingly low and high pH values originated from either acidic/photochemical corrosion of the catalyst and/or surface passivation with Zn(OH)2. Removal efficiency of cyanide greatly decreased in the presence of humic acid, ethylenediaminetetraacetic acid, nitrilotriacetic acid compared to that without presence of organic compound because of the competitive oxidation as well as surface blocking by relatively large organic compounds. The oxidation pattern of cyanide was better described by first-order kinetic model. Finally photocatalytic reaction with TiO2 or ZnO can be effectively applied to treat synthetic wastewater contaminated with cyanide.

Photocatalytic reduction of Cr(VI) from agricultural soil column leachates using zinc oxide under UV light irradiation

The photocatalytic reduction of Cr(VI) from agricultural soil leachates irrigated with Cr(VI)-containing waste hydroponic solution was evaluated in this work. For this purpose, zinc oxide was used as a catalyst under UV irradiation (lambda = 365 nm). The reduction of Cr(VI) was preliminarily evaluated on synthetic solutions with a concentration of 15 mg L(-1) to optimize the catalyst loading and the solution pH and to determine the effect of organic matter. Greater removal of Cr(VI) was observed at pH 7, and the optimum catalyst loading was found to be 2 g L(-1), which achieved an 84% Cr(VI) reduction in 6 h. The influence of dissolved organic matter on the reduction of Cr(VI) was evaluated through the addition of different concentrations of humic acid (HA) to the chromium solution. The removal of Cr(VI) was continuously enhanced as the HA concentration gradually increased from 0 to 14 mg L(-1). The percentage of hexavalent chromium reduction from soil leachates was in the range of 13-99%, and the rate constant was significantly enhanced by the presence of organic compounds in the soil pore water. Thus, a marked synergistic effect between the photocatalytic reduction of Cr(VI) and the organic matter in soil (e.g. humic substances) was observed in real samples and was similar to that observed in the Cr(VI) synthetic solution that contained HA.

Effect of different types of organic compounds on the photocatalytic reduction of Cr(VI)

The effect of different types of organic compounds (humic acid, oxalate, ethylenediaminetetraacetic acid, nitrilotriacetic acid, phenol) on the photocatalytic reduction of Cr(VI) with illuminated TiO2 was studied in this work with variation of the solution pH, contact time, initial Cr(VI) concentration and type of organic compounds. As the pH increased, the removal efficiency for Cr(VI) decreased. The increase in Cr(VI) removal by UV/TiO2 with decreasing solution pH was due to the increased potential difference between the conduction band of TiO2 and Cr(VI)/Cr(III) as well as the anionic-type adsorption of Cr(VI) on to the TiO2 surface. Removal efficiency for Cr(VI) increased in the presence of organic compound compared with that without organic compound because positive holes in the TiO2 were scavenged by organic additives. The reduction pattern of Cr(VI) was better described by the first-order kinetic model. Finally photocatalytic reaction with illuminated TiO2 can be effectively applied to treat wastewater contaminated with Cr(VI).