An In Vitro Evaluation of Fracture Reduction Achieved by Inflatable Bone Tamps Under Simulated Physiological Load

Biomechanical Comparisons between One- and Two-Compartment Devices for Reconstructing Vertebrae by Kyphoplasty

BACKGROUND

This biomechanical in vitro study compared two kyphoplasty devices for the extent of height reconstruction, load-bearing capacity, cement volume, and adjacent fracture under cyclic loading.

METHODS

Multisegmental (T11-L3) specimens were mounted into a testing machine and subjected to compression, creating an incomplete burst fracture of L1. Kyphoplasty was performed using a one- or two-compartment device. Then, the testing machine was used for a cyclic loading test of load-bearing capacity to compare the two groups for the amount of applied load until failure and subsequent adjacent fracture.

RESULTS

Vertebral body height reconstruction was effective for both groups but not statistically significantly different. After cyclic loading, refracture of vertebrae that had undergone kyphoplasty was not observed in any specimen, but fractures were observed in adjacent vertebrae. The differences between the numbers of cycles and of loads were not statistically significant. An increase in cement volume was strongly correlated with increased risks of adjacent fractures.

CONCLUSION

The two-compartment device was not substantially superior to the one-compartment device. The use of higher cement volume correlated with the occurrence of adjacent fractures.

Height restoration and sustainability using bilateral vertebral augmentation systems for vertebral compression fractures: a cadaveric study

BACKGROUND CONTEXT

The treatment of vertebral compression fractures using percutaneous augmentation is an effective method to reduce pain and decrease mortality rates. Surgical methods include vertebroplasty, kyphoplasty, and vertebral augmentation with implants. A previous study suggested that a titanium implantable vertebral augmentation device (TIVAD) produced superior height restoration compared to balloon kyphoplasty (BKP) but was based on a less clinically relevant biomechanical model. Moreover, the introduction of high pressure balloons and directional instruments may further aid in restoring height.

PURPOSE

The objective was to evaluate three procedures (BKP, BKP w/ Kyphon Assist (KA; directional instruments), and TIVAD) used for percutaneous augmentation of vertebral fractures with respect to height restoration and sustainability post-operatively.

STUDY DESIGN/SETTING

This is an in vitro cadaver study performed in a laboratory setting.

METHODS

Five osteoporotic female human cadaver thoracolumbar spines (age: 63-77 years, T-score: -2.5 to -3.5, levels: T7-S1) were scanned using computed tomography and dissected into 30 two-functional spine units (2FSUs). Vertebral wedge compression fractures were created by reducing the anterior height of the vertebrae by 25% and holding the maximum displacement for 15 minutes. Post-fracture, surgery was performed on each 2FSU with a constant 100 N load. Surgeries included BKP, BKP w/ KA, or TIVAD (n=10 per treatment group). Post-surgery, cyclic loading was performed on each 2FSU for 10,000 cycles at 600 N (walking), followed by 5,000 cycles at 850 N (standing up/sitting down), and 5,000 cycles at 1250 N (lifting a 5-10kg weight from the floor). Fluoroscopic images were taken and analyzed at the initial, post-fracture, post-surgery, and post-loading timepoints. Anterior, central, and posterior heights, Beck Index, and angle between endplates were assessed.

RESULTS

No difference in height restoration was observed among treatment groups (p=.72). Compared to the initial height, post-surgery anterior height was 96.3±8.7% for BKP, 94.0±10.0% for BKP w/ KA, and 95.3±5.8% for TIVAD. No difference in height sustainability in response to 600 N (p=.76) and 850 N (p=.20) load levels was observed among treatment groups. However, after 1250 N loading, anterior height decreased to 93.8±6.8% of the post-surgery height for BKP, 95.9±6.4% for BKP w/ KA, and 86.0±6.6% for TIVAD (p=.02). Specifically, the mean anterior height reduction between post-surgery and post-1250 N loading timepoints was lower for BKP w/ KA compared to TIVAD (p=.02), but not when comparing BKP to TIVAD (p=.07). No difference in Beck Index or angle between endplates was observed at any timepoint among the treatment groups.

CONCLUSIONS

The present study, utilizing a clinically relevant biomechanical model, demonstrated equivalent height restoration post-surgery and at relatively lower-level cyclic loading using BKP, BKP w/ KA, and TIVAD, contrary to results from a previous study. Less anterior height reduction in response to high-level cyclic loading was observed in the BKP w/ KA group compared to TIVAD.

CLINICAL SIGNIFICANCE

All three treatments can restore height similarly after a vertebral compression fracture, which may lead to pain reduction and decreased mortality. BKP w/ KA may exhibit less height loss in higher-demand patients who engage in physical activities that involve increased weight resistance.

A Study to Compare the Efficacy of a Biodegradable Dynamic Fixation System With Titanium Devices in Posterior Spinal Fusion Between Articular Processes in a Canine Model

The objective of this study was to apply a biodegradable dynamic fixation system (BDFS) for lumbar fusion between articular processes and compare the fusion results and biomechanical changes with those of conventional rigid fixation. Twenty-four mongrel dogs were randomly assigned to 2 groups and subjected to either posterior lumbar fusion surgery with a BDFS or titanium rods (TRs) at the L5-L6 segments. Six animals in each group were sacrificed at 8 or 16 weeks. Fusion conditions were evaluated by computed tomography (CT), manual palpation, biomechanical tests, and histological analysis. Biomechanical tests were performed at the L4-7 (for range of motion (ROM)) and L5-6 (for fusion stiffness) segments. Histological examination was performed on organs, surrounding tissues, and the fused area. The magnesium alloy components maintained their initial shape 8 weeks after the operation, but the meshing teeth were almost completely degraded at 16 weeks. The biomechanical analysis revealed an increased lateral bending ROM at 8 weeks and axial torsion ROM at 16 weeks. The L4-5 extension-flexion ROMs in the BDFS group were 2.29 ± 0.86 deg and 3.17 ± 1.08 deg at 16 weeks, respectively, compared with 3.22 ± 0.56 deg and 5.55 ± 1.84 deg in TR group. However, both groups showed similar fusion results. The BDFS design is suitable, and its degradation in vivo is safe. The BDFS can be applied for posterior lumbar fusion between articular processes to complete the fusion well. Additionally, the BDFS can reduce the decline in lateral motion and hypermotion of the cranial adjacent segment in flexion-extension motion.

The impact of different artificial disc heights during total cervical disc replacement: an in vitro biomechanical study

BACKGROUND

The principles of choosing an appropriate implant height remain controversial in total cervical disc replacement (TDR). By performing an in vitro biomechanical study and exploring the biomechanical impact of implant height on facet joint and motion function, the study aimed to offer valid proposals regarding implant height selection during TDR.

METHODS

A total of 6 fresh-frozen male cadaveric cervical spines (C2-C7) with 5 mm intervertebral disc height at C5/6 level were enrolled in the study. Specimens with the intact condition and with different height artificial discs were tested. Facet joint pressures and range of motion under each condition were recorded using a specialized machine.

RESULTS

The artificial disc heights that were involved in this study were 5 mm, 6 mm, and 7 mm. The range of motion decreased along with the increment of implant height, while facet joint pressure showed an opposite trend. Specimens with a 5 mm implant height could provide a similar range of motion (11.8° vs. 12.2° in flexion-extension, 8.7° vs. 9.0° in rotation, 7.9° vs. 8.2° in lateral bending) and facet joint pressure (27.8 psi vs. 25.2 psi in flexion, 59.7 psi vs. 58.9 psi in extension, 24.0 psi vs. 22.7 psi in rotation, 32.0 psi vs. 28.8 psi in lateral bending) compared with intact specimens. Facet joint pressure of specimens with 6 mm implant height (≥ 1 mm in height) increased during flexion at the C5-6 segment (30.4 psi vs. 25.2 psi, P = 0.076). However, specimens with 7 mm implant height (≥ 2 mm in height) showed a significant reduction in motion (9.5° vs. 12.2° in flexion-extension, P < 0.001) and increment of facet joint pressure at C5-6 segment (44.6 psi vs. 25.2 psi in flexion, 90.3 psi vs. 58.9 psi in extension, P < 0.0001) and adjacent segments.

CONCLUSIONS

This study suggested that an appropriate artificial disc height can achieve near-normal biomechanical properties and is recommended. We should be very cautious when using artificial discs ≥ 1 mm in height compared to normal. However, implants ≥ 2 mm in height compared to normal significantly increased the facet joint pressure and decreased the range of motion; therefore, it should not be used in clinical practice.

A novel dynamic fixation system with biodegradable components on lumbar fusion between articular processes in a canine model

The objective of this study was to design a novel dynamic fixation system with biodegradable components, apply it for lumbar fusion between articular processes and compare the fusion results and biomechanical changes to those of conventional rigid fixation. The novel dynamic fixation system was designed using a finite element model, stress distributions were compared and 24 mongrel dogs were randomly assigned to two groups and subjected to either posterior lumbar fusion surgery with a novel dynamic fixation system or titanium rods at the L5-L6 segments. Lumbar spines were assessed in both groups to detect radiographic, manual palpation and biomechanical changes. Histological examination was performed on organs and surrounding tissues. In the novel dynamic fixation system, stress was mainly distributed on the meshing teeth of the magnesium alloy spacer. The magnesium alloy components maintained their initial shape 8 weeks after the operation, but the meshing teeth were almost completely degraded at 16 weeks. The novel dynamic fixation system revealed an increased lateral bending range of motion at 8 weeks; however, both groups showed similar radiographic grades, fusion stiffness, manual palpation and histological results. The novel dynamic fixation system design is suitable, and its degradation in vivo is safe. The novel dynamic fixation system can be applied for posterior lumbar fusion between articular processes and complete the fusion like titanium rods.

Biomechanical effect of interspinous process distraction height after lumbar fixation surgery: An in vitro model

Pedicle screw fixation may induce abnormal activity at adjacent segment and accelerate the degeneration of lumbar vertebrae. Dynamic stabilizers could provide an intermediate solution between conservative treatment and fusion surgery. Lumbar vertebral segment cephalad to instrumented fixation was the most common localization of adjacent segment degeneration. The aim of this study is to explore the use of interspinous process devices in the lumbar vertebral segment cephalad to fixation segment in changing the mechanical distribution and limiting abnormal activity of the spine. Eight specimens were tested in the following groups: intact group, instability group (bilateral facetectomy at L3-L4), fixation group (bilateral facetectomy and pedicle screw fixation at L3-L4), and hybrid fixation group (fixation at L3-L4 and simulating interspinous device implantation of 6, 8, 10, 12, 14, 16, and 18 mm at L2-L3). Range of motion, motion of vertebral body, and strain distribution change were recorded. The range of motion in extension with 16- and 18-mm hybrid constructs was significantly lower than intact, instability, and fixation groups. In flexion and lateral bending, the strain values of L4 inferior articular process with 18-mm hybrid construct have a significant difference compared with other groups. In axial rotation, under the condition of a contralateral state, the strain values of L2 superior articular process with 18-mm hybrid construct have a significant difference compared with intact and fixation groups. The strain value of the L4 inferior articular process had negative correlation with height distraction in three dimensions, except extension. A negative correlation between the strain value of the L2 superior articular process and distraction height was found in contralateral bending and contralateral axial rotation. Interspinous process devices above the fixation segment can change the mechanical distribution of the spine and limit activity in some of the segments of the spine, which may delay the degeneration of the adjacent segment.