A sub-nW 2.4 GHz Transmitter for Low Data-Rate Sensing Applications

Synergistic effects of hybrid n-doping on the thermoelectric performance and air-stability of water-processable single-walled carbon nanotubes

Organic thermoelectrics (TEs) based on carbon nanotubes (CNTs) have attracted much attention with their inherent advantages, such as, earth-abundant elements, broad electronic tunability, and excellent mechanical compliance. However, the inferior TE performance and doping stability of n-type CNTs to those of p-type CNTs have been bottlenecks to establish CNT-based next-generation TEs. Herein, we report a hybrid n-doping method that improves the n-type TE performance and long-term air-stability of water-processable single-walled CNT (SWCNT) and carboxymethyl cellulose (CMC) composite. The hybrid n-doping process with polyethyleneimine (PEI) n-dopant contains primary addition and secondary immersion doping, which causes a simultaneous increase in electrical conductivity and Seebeck coefficient through efficient n-doping and surface energy filtering effect, respectively. Furthermore, the hybrid-doped films exhibit superior long-term stability by inhibiting the oxidation of SWCNT/CMC at nanoscale, which allows to ensure the initial power factor even after storing in ambient for a month. Finally, we successfully demonstrated hybrid-doped SWCNT/CMC-based TEGs with long-term stable output characteristics. This work can offer insights to develop efficient and air-stable n-type organic TE materials and devices.

Feasibility Assessment of an Optically Powered Digital Retinal Prosthesis Architecture for Retinal Ganglion Cell Stimulation

Clinical trials previously demonstrated the notable capacity to elicit visual percepts in blind patients affected with retinal diseases by electrically stimulating the remaining neurons on the retina. However, these implants restored very limited visual acuity and required transcutaneous cables traversing the eyeball, leading to reduced reliability and complex surgery with high postoperative infection risks. To overcome the limitations imposed by cables, a retinal implant architecture in which near-infrared illumination carries both power and data through the pupil to a digital stimulation controller is presented. A high efficiency multi-junction photovoltaic cell transduces the optical power to a CMOS stimulator capable of delivering flexible interleaved sequential stimulation through a diamond microelectrode array. To demonstrate the capacity to elicit a neural response with this approach while complying with the optical irradiance limit at the pupil, fluorescence imaging with a calcium indicator is used on a degenerate rat retina. The power delivered by the laser at the permissible irradiance of 4 mW/mm2 at 850 nm is shown to be sufficient to both power the stimulator ASIC and elicit a response in retinal ganglion cells (RGCs), with the ability to generate of up to 35 000 pulses per second at the average stimulation threshold. This confirms the feasibility of generating a response in RGCs with an infrared-powered digital architecture capable of delivering complex sequential stimulation patterns at high repetition rates, albeit with some limitations.

In-sensor neural network for high energy efficiency analog-to-information conversion

This work presents an on-chip analog-to-information conversion technique that utilizes analog hyper-dimensional computing based on reservoir-computing paradigm to process electrocardiograph (ECG) signals locally in-sensor and reduce radio frequency transmission by more than three orders-of-magnitude. Instead of transmitting the naturally sparse ECG signal or extracted features, the on-chip analog-to-information converter analyzes the ECG signal through a nonlinear reservoir kernel followed by an artificial neural network, and transmits the prediction results. The proposed technique is demonstrated for detection of sepsis onset and achieves state-of-the-art accuracy and energy efficiency while reducing sensor power by [Formula: see text] with test-chips prototyped in 65 nm CMOS.

A 0.66mW 400 MHz/900 MHz Transmitter IC for In-Body Bio-Sensing Applications

A sub-1GHz transmitter (TX) integrated chip (IC) with ultra-low power consumption and moderately high adjacent channel power rejection (ACPR) is presented for in-body bio-sensing applications. The 400 MHz 12-phase digital power amplifier (DPA) is implemented with the proposed 16QAM modulation scheme to improve the energy efficiency. The TX IC also contains a 900 MHz FSK TX realized with a symmetrical edge-combiner, which can be used in the low accuracy mode. A fully digital modulator with band shaping is integrated on the chip for the improvement of ACPR performance. Fabricated in 65-nm CMOS process, the chip occupies an active area of 0.75 mm². Under 0.5 V supply voltage, the TX consumes less than 0.66 mW power consumption while delivering -15 dBm of output power when operating at both bands. The presented TX has an energy efficiency performance comparable to the state-of-the-arts low power designs, with the measured average energy consumption of 64.5/220 pJ/bit, and the measured figure-of-merit (FoM) of 2.04/6.98 nJ/(bit · mW) for the two bands. Compared with the state-of-the-arts sub-1mW designs in literatures, the ACPR is improved by at least 13 dB.

Regulating Thermogalvanic Effect and Mechanical Robustness via Redox Ions for Flexible Quasi-Solid-State Thermocells

The design of power supply systems for wearable applications requires both flexibility and durability. Thermoelectrochemical cells (TECs) with large Seebeck coefficient can efficiently convert low-grade heat into electricity, thus having attracted considerable attention in recent years. Utilizing hydrogel electrolyte essentially addresses the electrolyte leakage and complicated packaging issues existing in conventional liquid-based TECs, which well satisfies the need for flexibility. Whereas, the concern of mechanical robustness to ensure stable energy output remains yet to be addressed. Herein, a flexible quasi-solid-state TEC is proposed based on the rational design of a hydrogel electrolyte, of which the thermogalvanic effect and mechanical robustness are simultaneously regulated via the multivalent ions of a redox couple. The introduced redox ions not only endow the hydrogel with excellent heat-to-electricity conversion capability, but also act as ionic crosslinks to afford a dual-crosslinked structure, resulting in reversible bonds for effective energy dissipation. The optimized TEC exhibits a high Seebeck coefficient of 1.43 mV K^-1 and a significantly improved fracture toughness of 3555 J m^-2, thereby can maintain a stable thermoelectrochemical performance against various harsh mechanical stimuli. This study reveals the high potential of the quasi-solid-state TEC as a flexible and durable energy supply system for wearable applications.

A Millimeter-Scale Crystal-Less MICS Transceiver for Insertable Smart Pills

This paper presents a millimeter-scale crystal-less wireless transceiver for volume-constrained insertable pills. Operating in the 402-405 MHz medical implant communication service (MICS) band, the phase-tracking receiver-based over-the-air carrier recovery has a ±160 ppm coverage. A fully integrated adaptive antenna impedance matching solution is proposed to calibrate the antenna impedance variation inside the body. A tunable matching network (TMN) with single inductor performs impedance matching for both transmitter (TX) and receiver (RX) and TX/RX mode switching. To dynamically calibrate the antenna impedance variation over different locations and diet conditions, a loop-back power detector using self-mixing is adopted, which expands the power contour up to 4.8 VSWR. The transceiver is implemented in a 40-nm CMOS technology, occupying 2 mm² die area. The transceiver chip and a miniature antenna are integrated in a 3.5 × 15 mm² area prototype wireless module. It has a receiver sensitivity of -90 dBm at 200 kbps data rate and delivers up to - 25 dBm EIRP in the wireless measurement with a liquid phantom.

Cyber-Physiochemical Interfaces

Living things rely on various physical, chemical, and biological interfaces, e.g., somatosensation, olfactory/gustatory perception, and nervous system response. They help organisms to perceive the world, adapt to their surroundings, and maintain internal and external balance. Interfacial information exchanges are complicated but efficient, delicate but precise, and multimodal but unisonous, which has driven researchers to study the science of such interfaces and develop techniques with potential applications in health monitoring, smart robotics, future wearable devices, and cyber physical/human systems. To understand better the issues in these interfaces, a cyber-physiochemical interface (CPI) that is capable of extracting biophysical and biochemical signals, and closely relating them to electronic, communication, and computing technology, to provide the core for aforementioned applications, is proposed. The scientific and technical progress in CPI is summarized, and the challenges to and strategies for building stable interfaces, including materials, sensor development, system integration, and data processing techniques are discussed. It is hoped that this will result in an unprecedented multi-disciplinary network of scientific collaboration in CPI to explore much uncharted territory for progress, providing technical inspiration-to the development of the next-generation personal healthcare technology, smart sports-technology, adaptive prosthetics and augmentation of human capability, etc.

A 2.4 GHz ISM Band OOK Transceiver With High Energy Efficiency for Biomedical Implantable Applications

This article presents a high energy efficiency, high-integrated, and low-power on-off keying transceiver for a 2.4 GHz industrial scientific medical band. The proposed receiver includes an input matching network, a low-noise amplifier, a novel single-to-differential envelope detector, a level shifter, cascaded baseband amplifiers, and a hysteresis comparator. The proposed transmitter includes a bias-stimulating circuit, a current-reused self-mixing voltage controlled oscillator, and a quadruple-transconductance power amplifier. Numerous proposed techniques implemented in the mentioned circuits improve the energy per bit and power efficiency. Therefore, the proposed receiver for short-distanced propagation can achieve a sensitivity of -46 dBm with a carrier frequency of 2.45 GHz and a high data rate of 2 Mbps. The proposed transmitter achieves an output power of -17 dBm with a high data rate of 20 Mbps. This work is fabricated in a TSMC 0.18 μm CMOS process and consumes 160 μW and 0.6 mW in the receiver and transmitter, respectively, from a 1.2 V supply voltage. The energy per bit of 80 pJ/bit in the receiver part and the figure of merit of 9 in the transmitter part are better than those of existing state-of-the-art transceivers.

Design of a Self-Controlled Dual-Oscillator-Based Supply Voltage Monitor for Biofuel-Cell-Combined Biosensing Systems in 65-nm CMOS and 55-nm DDC CMOS

A supply voltage monitor (SVM) with self-controlled dual-oscillator-based architecture is proposed herein for biosensing systems combined with a biofuel cell (BFC) in this paper. The output of the BFCs can be used to monitor the biological signals while powering the BFC-combined biosensing systems. Thus, the SVM is designed to convert the change in the supply voltage (V _DD) into a code. The architecture of the proposed SVM allows self-controlled periodic operation without external signals. Furthermore, the frequency subtraction technique that uses two oscillators employing gate-leakage-based architecture with different frequency sensitivities to V _DD allows accurate code generation with low power consumption and a small circuit area for supply voltage monitoring. The proposed SVM is fabricated using two different CMOS process technologies, including 65-nm CMOS and 55-nm deeply depleted channel (DDC) CMOS. The implementation of the 65-nm CMOS obtains an operating V _DD range of 250 mV (0.75-1 V), draws a standby power consumption of 1.4 nW at 0.75-V V _DD, exhibits a resolution of 2.4 mV with a nonlinearity error of -8.4/ +12.1 mV, and occupies a circuit area of 0.0047 mm². Meanwhile, the implementation of the 55-nm DDC CMOS for low-voltage operation achieves an operating V _DD range of 300 mV (0.225-0.525 V), draws a standby power consumption of 32.5 nW at 0.25-V V _DD, exhibits a resolution of 0.94 mV with a nonlinearity error of -15.2/ +14 mV, and occupies a circuit area of 0.0032 mm².

Compliant and stretchable thermoelectric coils for energy harvesting in miniature flexible devices

With accelerating trends in miniaturization of semiconductor devices, techniques for energy harvesting become increasingly important, especially in wearable technologies and sensors for the internet of things. Although thermoelectric systems have many attractive attributes in this context, maintaining large temperature differences across the device terminals and achieving low-thermal impedance interfaces to the surrounding environment become increasingly difficult to achieve as the characteristic dimensions decrease. Here, we propose and demonstrate an architectural solution to this problem, where thin-film active materials integrate into compliant, open three-dimensional (3D) forms. This approach not only enables efficient thermal impedance matching but also multiplies the heat flow through the harvester, thereby increasing the efficiencies for power conversion. Interconnected arrays of 3D thermoelectric coils built using microscale ribbons of monocrystalline silicon as the active material demonstrate these concepts. Quantitative measurements and simulations establish the basic operating principles and the key design features. The results suggest a scalable strategy for deploying hard thermoelectric thin-film materials in harvesters that can integrate effectively with soft materials systems, including those of the human body.

Extending the Limits of Wireless Power Transfer to Miniaturized Implantable Electronic Devices

Implantable electronic devices have been evolving at an astonishing pace, due to the development of fabrication techniques and consequent miniaturization, and a higher efficiency of sensors, actuators, processors and packaging. Implantable devices, with sensing, communication, actuation, and wireless power are of high demand, as they pave the way for new applications and therapies. Long-term and reliable powering of such devices has been a challenge since they were first introduced. This paper presents a review of representative state of the art implantable electronic devices, with wireless power capabilities, ranging from inductive coupling to ultrasounds. The different power transmission mechanisms are compared, to show that, without new methodologies, the power that can be safely transmitted to an implant is reaching its limit. Consequently, a new approach, capable of multiplying the available power inside a brain phantom for the same specific absorption rate (SAR) value, is proposed. In this paper, a setup was implemented to quadruple the power available in the implant, without breaking the SAR limits. A brain phantom was used for concept verification, with both simulation and measurement data.

A Subcubic Millimeter Wireless Implantable Intraocular Pressure Monitor Microsystem

We present a sub-mm³, fully wireless, implantable intraocular pressure monitor microsystem (IMM) that comprises a powering coil, an antenna, a piezoresistive micro-electro-mechanical system pressure sensor, and a pressure sensing IC. The system provides a 24-h intraocular pressure monitoring, which is not possible with currently used tonometric measurements. The IMM volume is limited to 0.38 mm³ (4 × smaller than previous state-of-the-art) for the studies on laboratory rodents prior to human use. A cavity resonator magnetic coupling delivers the wireless power to the chip with 4.89% efficiency. The chip senses a change in a differential sensor resistance by providing a low-power differential resistance to frequency conversion with the measured standard deviation in differential resistance sensing of . The data packets are wirelessly transmitted by an ultralow power 2.4-GHz ISM band OOK transmitter. The IMM is integrated on a 5-μm-thick biocompatible Parylene C substrate. Implemented in a 0.18-μm CMOS process, the system achieves 0.67-mmHg pressure sensitivity with differential resistance sensing and dissipates only 6.3 nW with 30 min of measurement intervals. We verify the IMM functionality in the in vivo biological experiment.

Design and Experimental Verification of a 0.19 V 53 μW 65 nm CMOS Integrated Supply-Sensing Sensor With a Supply-Insensitive Temperature Sensor and an Inductive-Coupling Transmitter for a Self-Powered Bio-sensing System Using a Biofuel Cell

In this paper, we present a self-powered bio-sensing system with the capability of proximity inductive-coupling communication for supply sensing and temperature monitoring. The proposed bio-sensing system includes a biofuel cell as a power source and a sensing frontend that is associated with the CMOS integrated supply-sensing sensor. The sensor consists of a digital-based gate leakage timer, a supply-insensitive time-domain temperature sensor, and a current-driven inductive-coupling transmitter and achieves low-voltage operation. The timer converts the output voltage from a biofuel cell to frequency. The temperature sensor provides a pulse width modulation (PWM) output that is not dependent on the supply voltage, and the associated inductive-coupling transmitter enables proximity communication. A test chip was fabricated in 65 nm CMOS technology and consumed 53 μW with a supply voltage of 190 mV. The low-voltage-friendly design satisfied the performance targets of each integrated sensor without any trimming. The chips allowed us to successfully demonstrate proximity communication with an asynchronous receiver, and the measurement results show the potential for self-powered operation using biofuel cells. The analysis and experimental verification of the system confirmed their robustness.