An Inductively-Powered Wireless Neural Recording and Stimulation System for Freely-Behaving Animals

A Power-Efficient Envelope-Detector-Less Amplitude-Shift-Keying Forward Telemetry for Wirelessly Powered Biomedical Devices

This paper proposes an envelope-detector-less (EDL) amplitude-shift-keying (ASK) forward telemetry (FT) demodulator for wireless power/data transfer (WPDT) systems. The EDL ASK FT demodulator can substitute bulky and power-hungry components, which are an envelope detector and an analog comparator in the conventional ASK FT demodulator, with a digital controller, reducing both power dissipation and chip area. The proposed demodulator shares the gate control signals of pass transistors, which are used in an ac-dc regulator for wireless power reception, to maintain a constant load voltage while efficiently demodulating the forward telemetry data. Also, a proposed digital cleaner in the EDL demodulator refines this control signal into a wide pulse without suffering from resonant frequency noise, while a synchronizer can align its frequency with the data rate and resonant frequency. The 0.25-µm CMOS prototype chip of the proposed power-path-less EDL ASK FT demodulator, equipped with the ac-dc regulator, demonstrates a significant 38.2% reduction in power dissipation compared to the conventional ASK FT demodulator. Moreover, the EDL ASK FT demodulator occupies only 0.023-mm2 silicon area and achieves a low bit error rate (BER) less than 10-4 while maintaining a regulated voltage of 4.5 V on the load.

Maze-Based Scalable Wireless Power Transmission Experimental Arena for Freely Moving Small Animals Applications

This paper presents an innovative T/Y-maze-based wireless power transmission (WPT) system designed to monitor spatial reference memory and learning behavior in freely moving rats. The system facilitates uninterrupted optical/electrical stimulation and neural recording experiments through the integration of wireless headstages or implants in T/Y maze setups. Utilizing an array of resonators covering the entire underneath of the mazes, the wireless platform ensures scalability with various configurations. The array is designed to ensure a natural localization mechanism to localize the Tx power toward the location of the Rx coil. The system is analyzed and modeled using ANSYS HFSS software to optimize design. The primary goal was to achieve uniform wireless power delivery throughout the mazes through a comparative study of different transmitter (Tx) array configurations, such as float, series, and parallel resonators. The calculated Specific Absorption Rate (SAR) in rat tissue model equals 1.7 W/kg at the power carrier frequency of 13.56 MHz. A prototype of the proposed maze-based WPT design, featuring 8 Tx resonators, a Tx coil and power amplifier, and a headstage power harvesting unit, is successfully implemented and its performance characterized for all three resonator configurations. The implemented T-maze-based WPT system has a total length of 128 cm. In the overlapping Tx resonators configuration, a homogeneity of 94% is achieved for the measured power transfer efficiency at over 30%, while continuously delivering over 60 mW for series configuration.

Development of Ocular Muscle Stimulation Systems and Optimization of Electrical Stimulus Parameters for Paralytic Strabismus Treatment

Paralysis of the extraocular muscles can lead to complications such as strabismus, diplopia, and loss of stereopsis. Current surgical treatments aim to mitigate these issues by resecting the paralyzed muscle or transposing the other recti muscles to the paralyzed muscle, but they do not fully improve the patient's quality of life. Electrical stimulation shows promise, while requiring further in vivo experiments and research on various stimulation parameters. In this study, we conducted experiments on rabbits to stimulate the superior rectus (SR) muscles using different parameters and stimulation waveforms. To provide various types of electrical stimulation, we developed the ocular muscle stimulation systems capable of both current controlled stimulation (CCS) and high-frequency stimulation (HFS), along with the chip that enables energy-efficient and safe switched-capacitor stimulation (SCS). We also developed electrodes for easy implantation and employed safe and efficient stimulation methods including CCS, SCS, and HFS. The in vivo animal experiments on normal and paralyzed SR muscles of rabbits showed that eyeball abduction angles were proportional to the current and pulse width of the stimulation. With the decaying exponential stimuli of the SCS system, eyeball abductions were 2.58× and 5.65× larger for normal and paralyzed muscles, respectively, compared to the rectangular stimulus of CCS. HFS achieved 0.92× and 0.26× abduction for normal and paralyzed muscles, respectively, with half energy compared to CCS. In addition, the continuous changes in eyeball abduction angle in response to varying stimulation intensity over time were observed.

Active Neural Interface Circuits and Systems for Selective Control of Peripheral Nerves: A Review

Interfaces with peripheral nerves have been widely developed to enable bioelectronic control of neural activity. Peripheral nerve neuromodulation shows great potential in addressing motor dysfunctions, neurological disorders, and psychiatric conditions. The integration of high-density neural electrodes with stimulation and recording circuits poses a challenge in the design of neural interfaces. Recent advances in active electrode strategies have achieved improved reliability and performance by implementing in-situ control, stimulation, and recording of neural fibers. This paper presents an overview of state-of-the-art neural interface systems that comprise a range of neural electrodes, neurostimulators, and bio-amplifier circuits, with a special focus on interfaces for the peripheral nerves. A discussion on the efficacy of active electrode systems and recommendations for future directions conclude this paper.

A Design Review for Biomedical Wireless Power Transfer Systems with a Three-Coil Inductive Link through a Case Study for NICU Applications

This paper outlines a design approach for biomedical wireless power transfer systems with a focus on three-coil inductive links for neonatal intensive care unit applications. The relevant literature has been explored to support the design approach, equations, simulation results, and the process of experimental analysis. The paper begins with a brief overview of various power amplifier classes, followed by an in-depth examination of the most common power amplifiers used in biomedical wireless power transfer systems. Among the traditional linear and switching amplifier classes, class-D and class-E switching amplifiers are highlighted for their enhanced efficiency and straightforward implementation in biomedical contexts. The impact of load variation on these systems is also discussed. This paper then explores the basic concepts and essential equations governing inductive links, comparing two-coil and multi-coil configurations. In the following, the paper discusses foundational coil parameters and provides theoretical and experimental analysis of both two-coil and multi-coil inductive links through step-by-step measurement techniques using lab equipment and addressing the relevant challenges. Finally, a case study for neonatal intensive care unit applications is presented, showcasing a wireless power transfer system operating at 13.56 MHz for powering a wearable device on a patient lying on a mattress. An inductive link with a transmitter coil embedded in a mattress is designed to supply power to a load at distances ranging from 4 cm to 12 cm, simulating the mattress-to-chest distance of an infant. the experimental results of a three-coil inductive link equipped with a Class-E power amplifier are reported, demonstrating power transfer efficiency ranging from 75% to 25% and power delivery to a 500 Ω-load varying from 340 mW to 25 mW over various distances.

Ultra-Compact Pulse Charger for Lithium Polymer Battery With Simple Built-in Resistance Compensation in Biomedical Applications

Active implantable medical devices (AIMDs) rely on batteries for uninterrupted operation and patient safety. Therefore, it is critical to ensure battery safety and longevity. To achieve this, constant current/constant voltage (CC/CV) methods have been commonly used and research has been conducted to compensate for the effects of built-in resistance (BIR) of batteries. However, conventional CC/CV methods may pose the risk of lithium plating. Furthermore, conventional compensation methods for BIR require external components, complex algorithms, or large chip sizes, which inhibit the miniaturization and integration of AIMDs. To address this issue, we have developed a pulse charger that utilizes pulse current to ensure battery safety and facilitate easy compensation for BIR. A comparison with previous research on BIR compensation shows that our approach achieves the smallest chip size of 0.0062 mm2 and the lowest system complexity using 1-bit ADC. In addition, we have demonstrated a reduction in charging time by at least 44.4% compared to conventional CC/CV methods, validating the effectiveness of our system's BIR compensation. The compact size and safety features of the proposed charging system make it promising for AIMDs, which have space-constrained environments.

Wireless closed-loop deep brain stimulation using microelectrode array probes

Deep brain stimulation (DBS), including optical stimulation and electrical stimulation, has been demonstrated considerable value in exploring pathological brain activity and developing treatments for neural disorders. Advances in DBS microsystems based on implantable microelectrode array (MEA) probes have opened up new opportunities for closed-loop DBS (CL-DBS) in situ. This technology can be used to detect damaged brain circuits and test the therapeutic potential for modulating the output of these circuits in a variety of diseases simultaneously. Despite the success and rapid utilization of MEA probe-based CL-DBS microsystems, key challenges, including excessive wired communication, need to be urgently resolved. In this review, we considered recent advances in MEA probe-based wireless CL-DBS microsystems and outlined the major issues and promising prospects in this field. This technology has the potential to offer novel therapeutic options for psychiatric disorders in the future.

Dense, 11 V-Tolerant, Balanced Stimulator IC with Digital Time-Domain Calibration for 100 nA Error

This article presents a multichannel neurostimulator implementing a novel charge balancing technique to achieve maximal integration. Safe neurostimulation demands accurate charge balancing of the stimulation waveforms to prevent charge build-up on the electrode-tissue interface. We propose digital time-domain calibration (DTDC), which adjusts the second phase of the biphasic stimulation pulses digitally, based on a one-time characterization of all stimulator channels with an on-chip ADC. Accurate control of the stimulation current amplitude is loosened in exchange for time-domain corrections, relieving circuit matching constraints and consequentially saving channel area. A theoretical analysis of DTDC is presented, establishing expressions for the required time resolution and the new, relaxed circuit matching constraints. To validate the DTDC principle, a 16-channel stimulator was implemented in 65 nm CMOS, requiring only 0.0141 mm 2 area/channel. Despite being implemented in a standard CMOS technology, 10.4 V compliance is achieved for compatibility with high-impedance microelectrode arrays typical for high-resolution neural prostheses. To the authors' knowledge, this is the first stimulator in a 65 nm low-voltage process achieving over 10 V output swing. Measurements after calibration show the DC error is successfully reduced below 96 nA on all channels. Static power consumption is 20.3 µW/channel.

Miniaturization for wearable EEG systems: recording hardware and data processing

As more people desire at-home diagnosis and treatment for their health improvement, healthcare devices have become more wearable, comfortable, and easy to use. In that sense, the miniaturization of electroencephalography (EEG) systems is a major challenge for developing daily-life healthcare devices. Recently, because of the intertwined relationship between EEG recording and processing, co-research of EEG recording hardware and data processing has been emphasized for whole-in-one miniaturized EEG systems. This paper introduces miniaturization techniques in analog-front-end hardware and processing algorithms for such EEG systems. To miniaturize EEG recording hardware, various types of compact electrodes and mm-sized integrated circuits (IC) techniques including artifact rejection are studied to record accurate EEG signals in a much smaller manner. Active electrode and in-ear EEG technologies are also researched to make small-form-factor EEG measurement structures. Furthermore, miniaturization techniques for EEG processing are discussed including channel selection techniques that reduce the number of required electrode channel and hardware implementation of processing algorithms that simplify the EEG processing stage.

A resonant current-mode wireless power transfer for implantable medical devices: an overview

Implantable Medical Devices (IMDs) have been developing in ways to be lighter and lower-power systems. In the view of such developments, the battery recharging capacity to ensure the stable operation of the system is essential. Wireless power transfer (WPT) was proposed as a solution to recharge the battery without complex metallic contacts. However, due to limitations such as threshold voltage of power switches and minimal input power of the multi-stage structure (Rectifier + Regulator/DC-DC converter) of conventional voltage-mode (VM) WPT, there are drawbacks of an input power range above a certain threshold level and limitations due to strict regulations on the human body. These issues make the design of the IMD battery charger much harder and prevent IMDs from being a more viable option for people-in-need. This paper introduces distinguishing characteristics of resonant current-mode (RCM) WPT technology to overcome the aforementioned issues. It also describes the basic theory, conventional circuits of VM/RCM, comparisons, and major challenges of RCM. Finally, advanced and efficiency-enhancing techniques of the-state-of-art works among the RCM topologies will be discussed to follow up the trend of RCM WPT.

A Load-Insensitive Hybrid LSK Back Telemetry System With Slope-Based Demodulation for Inductively Powered Biomedical Devices

This paper presents a hybrid load-shift keying (LSK) modulation for a load-insensitive back telemetry system to realize near-constant voltage changes in a primary coil (L₁) against a wide range of load variations. The hybrid-LSK-enabled full-wave rectifier enables the sequential combination of open- and short-coil functions for hybrid-LSK modulation in addition to wireless power conversion operation. Load-insensitive L₁ voltage changes can be demodulated using the proposed slope- based demodulator, which utilizes the threshold slope of L₁ voltage changes over the back data pulse width, enabling robust data recovery regardless of the load conditions. The 0.56-mm² 0.18-μm standard CMOS hybrid-LSK prototype demonstrated that the variation of L₁ voltage changes could be minimized to 60 mV under load changes between 50 Ω and 50 kΩ at coil separation distance of 10 mm, achieving 88.2% reduction compared to the conventional short-coil LSK with 510 mV variation. The proposed back telemetry system also achieved a bit error rate (BER) of < 9.1 × 10^-10 under load ranges from 50 Ω to 50 kΩ and data rate of 1 Mbps, ensuring reliable back data recovery against load variations.

Seamless Capacitive Body Channel Wireless Power Transmission Toward Freely Moving Multiple Animals in an Animal Cage

Unstable wireless power transmission toward multiple living animals in an animal cage is one of the significant barriers to performing long-term and real-time neural monitoring in preclinical research. Here, seamless capacitive body channel (SCB) wireless power transmission (WPT) along with power management integrated circuit (PMIC) is designed using a standard 65 nm CMOS process. The SCB WPT enables stable wireless power transmission toward multiple 35 mm×20 mm×2 mm sized receivers (RXs) attached to freely moving animals in a 600 mm×600 mm×120 mm sized animal cage. By utilizing fringe-field capacitance and a body channel for wireless power link between the cage and RXs, the maximum difference in all measured power efficiencies in diverse scenarios is only 6.66 % with a 20 mW load. Even with a 90 ^° RX rotation against the cage, power efficiency marks 17.76 %. Furthermore, an in-vivo experiment conducted with three untethered rats demonstrates the capability of continuous long-term power delivery in practical situations.

Advances in Neural Recording and Stimulation Integrated Circuits

In the past few decades, driven by the increasing demands in the biomedical field aiming to cure neurological diseases and improve the quality of daily lives of the patients, researchers began to take advantage of the semiconductor technology to develop miniaturized and power-efficient chips for implantable applications. The emergence of the integrated circuits for neural prosthesis improves the treatment process of epilepsy, hearing loss, retinal damage, and other neurological diseases, which brings benefits to many patients. However, considering the safety and accuracy in the neural prosthesis process, there are many research directions. In the process of chip design, designers need to carefully analyze various parameters, and investigate different design techniques. This article presents the advances in neural recording and stimulation integrated circuits, including (1) a brief introduction of the basics of neural prosthesis circuits and the repair process in the bionic neural link, (2) a systematic introduction of the basic architecture and the latest technology of neural recording and stimulation integrated circuits, (3) a summary of the key issues of neural recording and stimulation integrated circuits, and (4) a discussion about the considerations of neural recording and stimulation circuit architecture selection and a discussion of future trends. The overview would help the designers to understand the latest performances in many aspects and to meet the design requirements better.

Closed-loop neuromodulation will increase the utility of mouse models in Bioelectronic Medicine

Mouse models have been of tremendous benefit to medical science for the better part of a century, yet bioelectronic medicine research using mice has been limited to mostly acute studies because of a lack of tools for chronic stimulation and sensing. A wireless neuromodulation platform small enough for implantation in mice will significantly increase the utility of mouse models in bioelectronic medicine. This perspective examines the necessary functionality of such a system and the technical challenges needed to be overcome for its development. Recent progress is examined and the outlook for the future of implantable devices for mice is discussed.

Low-Cutoff Frequency Reduction in Neural Amplifiers: Analysis and Implementation in CMOS 65 nm

Scaling down technology demotes the parameters of AC-coupled neural amplifiers, such as increasing the low-cutoff frequency due to the short-channel effects. To improve the low-cutoff frequency, one solution is to increase the feedback capacitors' value. This solution is not desirable, as the input capacitors have to be increased to maintain the same gain, which increases the area and decreases the input impedance of the neural amplifier. We analytically analyze the small-signal behavior of the neural amplifier and prove that the main reason for the increase of the low-cutoff frequency in advanced CMOS technologies is the reduction of the input resistance of the operational transconductance amplifier (OTA). We also show that the reduction of the input resistance of the OTA is due to the increase in the gate oxide leakage in the input transistors. In this paper, we explore this fact and propose two solutions to reduce the low-cutoff frequency without increasing the value of the feedback capacitor. The first solution is performed by only simulation and is called cross-coupled positive feedback that uses pseudoresistors to provide a negative resistance to increase the input resistance of the OTA. As an advantage, only standard CMOS transistors are used in this method. Simulation results show that a low-cutoff frequency of 1.5 Hz is achieved while the midband gain is 30.4 dB at 1 V. In addition, the power consumption is 0.6 μW. In the second method, we utilize thick-oxide MOS transistors in the input differential pair of the OTA. We designed and fabricated the second method in the 65 nm TSMC CMOS process. Measured results are obtained by in vitro recordings on slices of mouse brainstem. The measurement results show that the bandwidth is between 2 Hz and 5.6 kHz. The neural amplifier has 34.3 dB voltage gain in midband and consumes 3.63 μW at 1 V power supply. The measurement results show an input-referred noise of 6.1 μV_rms and occupy 0.04 mm² silicon area.

Duty-Cycled Wireless Power Transmission for Millimeter-Sized Biomedical Implants

Wireless power transmission (WPT) using an inductively coupled link is one of the most popular approaches to deliver power wirelessly to biomedical implants. As the electromagnetic wave travels through the tissue, it is attenuated and absorbed by the tissue, resulting in much weaker electromagnetic coupling than in the air. As a result, the received input power on the implant is very weak, and so is the input voltage at the rectifier, which is the first block that receives the power on the implant. With such a small voltage amplitude, the rectifier inevitably has a very poor power conversion efficiency (PCE), leading to a poor power transfer efficiency (PTE) of the overall WPT system. To address this challenge, we propose a new system-level WPT method based on duty cycling of the power transmission for millimeter-scale implants. In the proposed method, the power transmitter (TX) transmits the wave with a duty cycle. It transmits only during a short period of time and pauses for a while instead of transmitting the wave continuously. In doing so, the TX power during the active period can be increased while preserving the average TX power and the specific absorption rate (SAR). Then, the incoming voltage becomes significantly larger at the rectifier, so the rectifier can rectify the input with a higher PCE, leading to improved PTE. To investigate the design challenges and applicability of the proposed duty-cycled WPT method, a case for powering a 1 × 1-mm2-sized neural implant through the skull is constructed. The implant, a TX, and the associated environment are modeled in High-Frequency Structure Simulator (HFSS), and the circuit simulations are conducted in Cadence with circuit components in a 180-nm CMOS process. At a load resistor of 100 kΩ, an output capacitor of 4 nF, and a carrier frequency of 144 MHz, the rectifier’s DC output voltage and PCE are increased by 300% (from 1.5 V to 6 V) and by 50% (from 14% to 64%), respectively, when the duty cycle ratio of the proposed duty-cycled power transmission is varied from 100% to 5%.

A Trimodal Wireless Implantable Neural Interface System-on-Chip

A wireless and battery-less trimodal neural interface system-on-chip (SoC), capable of 16-ch neural recording, 8-ch electrical stimulation, and 16-ch optical stimulation, all integrated on a 5 ×  3 mm2 chip fabricated in 0.35-μm standard CMOS process. The trimodal SoC is designed to be inductively powered and communicated. The downlink data telemetry utilizes on-off keying pulse-position modulation (OOK-PPM) of the power carrier to deliver configuration and control commands at 50 kbps. The analog front-end (AFE) provides adjustable mid-band gain of 55-70 dB, low/high cut-off frequencies of 1-100 Hz/10 kHz, and input-referred noise of 3.46 μVrms within 1 Hz-50 kHz band. AFE outputs of every two-channel are digitized by a 50 kS/s 10-bit SAR-ADC, and multiplexed together to form a 6.78 Mbps data stream to be sent out by OOK modulating a 434 MHz RF carrier through a power amplifier (PA) and 6 cm monopole antenna, which form the uplink data telemetry. Optical stimulation has a switched-capacitor based stimulation (SCS) architecture, which can sequentially charge four storage capacitor banks up to 4 V and discharge them in selected μLEDs at instantaneous current levels of up to 24.8 mA on demand. Electrical stimulation is supported by four independently driven stimulating sites at 5-bit controllable current levels in ±(25-775) μA range, while active/passive charge balancing circuits ensure safety. In vivo testing was conducted on four anesthetized rats to verify the functionality of the trimodal SoC.

OSERR: an open-source standalone electrophysiology recording system for rodents

Behavioral assessment of rodents is critical for investigation of brain function in health and disease. In vivo neurophysiological recordings are powerful tools to mechanistically dissect neural pathways that underlie behavioral changes, and serve as markers for dynamics, efficacy and safety of potential therapeutic approaches. However, most in vivo recording systems require tethers or telemetry receivers, limiting their compatibility with some behavioral tests. Here, we developed an open-source standalone electrophysiology recording system for rodents (OSERR). It is a tether-free, standalone recording device with two channels, a reference and a ground, that acquires, amplifies, filters and stores data all in itself. Thus, it does not require any cable or receiver. It is also compact and light-weight, and compatible with juvenile mice, as well as multiple recording modalities and standard electrode implantation methods. In addition, we provide the complete design of hardware, and software for operation. As an example, we demonstrated that this standalone system, when configured with a bandwidth of 1–120 Hz and gain of 1000, successfully collected EEG signals during induced seizure, extended recording, anesthesia, and social interactions in mice. The design of this system is practical, economical, and freely available. Thus, this system could enable recording of brain activity during diverse behavioral assays in a variety of arenas and settings, and allow simultaneous recordings from multiple subjects to examine social behaviors. Importantly, with the open-source documentation, researchers could customize the design of the system to their specific needs.

Noise Optimization Techniques for Switched-Capacitor Based Neural Interfaces

This paper presents the noise optimization of a novel switched-capacitor (SC) based neural interface architecture, and its circuit demonstration in a 0.13 [Formula: see text] CMOS process. To reduce thermal noise folding ratio, and suppress kT/C noise, several noise optimization techniques are developed in the proposed architecture. First, one parasitic capacitance suppression scheme is developed to block noise charge transfer from parasitic capacitors to amplifier output. Second, one recording path-splitting scheme is proposed in the input sampling stage to selectively record local field potentials (LFPs), extracellular spikes, or both for reducing input noise floor, and total power consumption. Third, an auto-zero noise cancellation scheme is developed to suppress kT/C noise in the neural amplifier stage. A prototype neural interface chip was fabricated, and also verified in both bench-top, and In-Vivo experiments. Bench-top testings show the input-referred noise of the designed chip is 4.8 [Formula: see text] from 1 [Formula: see text] to 300 [Formula: see text], and 2.3 [Formula: see text] from 300 [Formula: see text] to 8 kHz respectively, and In-Vivo experiments show the peak-to-peak amplitude of the total noise floor including neural activity, electrode interface noise, and the designed chip is only around 20 [Formula: see text]. In comparison with conventional architectures through both circuit measurement and animal experiments, it is well demonstrated that the proposed noise optimization techniques can effectively reduce circuit noise floor, thus extending the application range of switched-capacitor circuits.

Power-saving design opportunities for wireless intracortical brain-computer interfaces

The efficacy of wireless intracortical brain-computer interfaces (iBCIs) is limited in part by the number of recording channels, which is constrained by the power budget of the implantable system. Designing wireless iBCIs that provide the high-quality recordings of today's wired neural interfaces may lead to inadvertent over-design at the expense of power consumption and scalability. Here, we report analyses of neural signals collected from experimental iBCI measurements in rhesus macaques and from a clinical-trial participant with implanted 96-channel Utah multielectrode arrays to understand the trade-offs between signal quality and decoder performance. Moreover, we propose an efficient hardware design for clinically viable iBCIs, and suggest that the circuit design parameters of current recording iBCIs can be relaxed considerably without loss of performance. The proposed design may allow for an order-of-magnitude power savings and lead to clinically viable iBCIs with a higher channel count.

From Seizure Detection to Smart and Fully Embedded Seizure Prediction Engine: A Review

Recent review papers have investigated seizure prediction, creating the possibility of preempting epileptic seizures. Correct seizure prediction can significantly improve the standard of living for the majority of epileptic patients, as the unpredictability of seizures is a major concern for them. Today, the development of algorithms, particularly in the field of machine learning, enables reliable and accurate seizure prediction using desktop computers. However, despite extensive research effort being devoted to developing seizure detection integrated circuits (ICs), dedicated seizure prediction ICs have not been developed yet. We believe that interdisciplinary study of system architecture, analog and digital ICs, and machine learning algorithms can promote the translation of scientific theory to a more realistic intelligent, integrated, and low-power system that can truly improve the standard of living for epileptic patients. This review explores topics ranging from signal acquisition analog circuits to classification algorithms and dedicated digital signal processing circuits for detection and prediction purposes, to provide a comprehensive and useful guideline for the construction, implementation and optimization of wearable and integrated smart seizure prediction systems.

SenseBack - An Implantable System for Bidirectional Neural Interfacing

Chronic in-vivo neurophysiology experiments require highly miniaturized, remotely powered multi-channel neural interfaces which are currently lacking in power or flexibility post implantation. To resolve this problem we present the SenseBack system, a post-implantation reprogrammable wireless 32-channel bidirectional neural interfacing device that can enable chronic peripheral electrophysiology experiments in freely behaving small animals. The large number of channels for a peripheral neural interface, coupled with fully implantable hardware and complete software flexibility enable complex in-vivo studies where the system can adapt to evolving study needs as they arise. In complementary \textit{ex-vivo} and \textit{in-vivo} preparations, we demonstrate that this system can record neural signals and perform high-voltage, bipolar stimulation on any channel. In addition, we demonstrate transcutaneous power delivery and Bluetooth 5 data communication with a PC. The SenseBack system is capable of stimulation on any channel with 20 V of compliance and up to 315 A of current, and highly configurable recording with per-channel adjustable gain and filtering with 8 sets of 10-bit ADCs to sample data at 20 kHz for each channel. To our knowledge this is the first such implantable research platform offering this level of performance and flexibility post-implantation (including complete reprogramming even after encapsulation) for small animal electrophysiology. Here we present initial acute trials, demonstrations and progress towards a system that we expect to enable a wide range of electrophysiology experiments in freely behaving animals.

Fully Passive Flexible Wireless Neural Recorder for the Acquisition of Neuropotentials from a Rat Model

Wireless implantable neural interfaces can record high-resolution neuropotentials without constraining patient movement. Existing wireless systems often require intracranial wires to connect implanted electrodes to an external head stage or/and deploy an application-specific integrated circuit (ASIC), which is battery-powered or externally power-transferred, raising safety concerns such as infection, electronics failure, or heat-induced tissue damage. This work presents a biocompatible, flexible, implantable neural recorder capable of wireless acquisition of neuropotentials without wires, batteries, energy harvesting units, or active electronics. The recorder, fabricated on a thin polyimide substrate, features a small footprint of 9 mm × 8 mm × 0.3 mm and is composed of passive electronic components. The absence of active electronics on the device leads to near zero power consumption, inherently avoiding the catastrophic failure of active electronics. We performed both in vitro validation in a tissue-simulating phantom and in vivo validation in an epileptic rat. The fully passive wireless recorder was implanted under rat scalp to measure neuropotentials from its contact electrodes. The implanted wireless recorder demonstrated its capability to capture low voltage neuropotentials, including somatosensory evoked potentials (SSEPs), and interictal epileptiform discharges (IEDs). Wirelessly recorded SSEP and IED signals were directly compared to those from wired electrodes to demonstrate the efficacy of the wireless data. In addition, a convoluted neural network-based machine learning algorithm successfully achieved IED signal recognition accuracy as high as 100 and 91% in wired and wireless IED data, respectively. These results strongly support the fully passive wireless neural recorder's capability to measure neuropotentials as low as tens of microvolts. With further improvement, the recorder system presented in this work may find wide applications in future brain machine interface systems.

A Software-Defined Radio Receiver for Wireless Recording From Freely Behaving Animals

To eliminate tethering effects on the small animals' behavior during electrophysiology experiments, such as neural interfacing, a robust and wideband wireless data link is needed for communicating with the implanted sensing elements without blind spots. We present a software-defined radio (SDR) based scalable data acquisition system, which can be programmed to provide coverage over standard-sized or customized experimental arenas. The incoming RF signal with the highest power among SDRs is selected in real-time to prevent data loss in the presence of spatial and angular misalignments between the transmitter (Tx) and receiver (Rx) antennas. A 32-channel wireless neural recording system-on-a-chip (SoC), known as WINeRS-8, is embedded in a headstage and transmits digitalized raw neural signals, which are sampled at 25 kHz/ch, at 9 Mbps via on-off keying (OOK) of a 434 MHz RF carrier. Measurement results show that the dual-SDR Rx system reduces the packet loss down to 0.12%, on average, by eliminating the blind spots caused by the moving Tx directionality. The system operation is verified in vivo on a freely behaving rat and compared with a commercial hardwired system.