The Effects of Ultrasonic Scaling and Air-Abrasive Powders on the Topography of Implant Surfaces: Scanning Electron Analysis and In Vitro Study

OBJECTIVES

 This in vitro study aimed to investigate the impact of bicarbonate air-abrasive powders and ultrasonic scaling with stainless steel tips on the micro- and nanotopography and roughness of three different implant-abutment junction titanium surfaces.

MATERIALS AND METHODS

 Three types of sterile and decontaminated titanium surfaces (RS, UTM, XA) were used for analysis. Nine disks per surface type were subjected to micro- and nanotopography analysis, scanning electron microscopy (SEM), roughness analysis, and fibroblast cultivation. Ultrasonic debridement and air polishing were performed on the surfaces. Human dermal fibroblasts were cultured on the surfaces for 5 days.

STATISTICAL ANALYSIS

 Data analysis adhered to ISO 25178 standards for surface texture assessment. SEM micrographs were used to reconstruct areas for extracting roughness parameters. Excel and Mex 6.0 software were utilized for quantitative and stereoscopic analysis.

RESULTS

 The study found varying effects on surface roughness posttreatment. RS Disco samples exhibited higher surface roughness compared with UTM and XA samples, both in average and nanoscale roughness. Decontamination led to increased surface roughness for all samples, particularly RS Disco. Fibroblast growth tests revealed enhanced cell network formation on decontaminated discs, possibly due to increased nanoscale roughness or the presence of bicarbonate salts.

CONCLUSION

 The study underscores the complex interplay between surface topography, microbial biofilm, and treatment efficacy in peri-implant disease management. While smoother surfaces may resist biofilm accumulation, increased nanoscale roughness postdecontamination can enhance fibroblast attachment and soft tissue integration. This dichotomy highlights the need for tailored treatment protocols that consider material-specific factors, emphasizing that successful implant therapy should balance microbial control with conducive surface characteristics for long-term osseointegration and soft tissue stability.

Atomic layer deposited TiO2 nanofilm on titanium implant for reduced the release of particles

Objective: Titanium implants are widely used in surgeries for their biocompatibility and mechanical properties. However, excessive titanium particle release can cause implant failure. This study explores Atomic Layer Deposition (ALD) to coat commercially pure titanium (Cp-Ti) with TiO2, aiming to improve its frictional and corrosion resistance while reducing particle release. By comparing TiO2 films with varying ALD cycle numbers, we assess surface properties, particle release, friction, and corrosion performance, providing insights into mitigating particle release from implants. Methods: Cp-Ti surfaces were prepared and coated with TiO2 films of 100, 300, and 500 ALD cycles. Surface characterization involved SEM, EDX, and XRD. Friction was tested using SEM, nanoindentation, and ICP-MS. Corrosion resistance was evaluated through immersion tests and electrochemical analysis. Cytotoxicity was assessed using BMSCs. Results: Surface characterization revealed smoother surfaces with increased ALD cycles, confirming successful TiO2 deposition. Friction testing showed reduced friction coefficients with higher ALD cycles, supported by nanoindentation results. Corrosion resistance improved with increasing ALD cycles, as evidenced by electrochemical tests and reduced titanium release. Cytotoxicity studies showed no significant cytotoxic effects. Conclusion: ALD-coated TiO2 films significantly enhance frictional and corrosion resistance of titanium implants while reducing particle release. The study underscores the importance of ALD cycle numbers in optimizing film performance, offering insights for designing implants with improved properties.

Physical-chemical influences and cell behavior of natural compounds on titanium dental surfaces

The present study evaluated the influence of carvacrol, terpinene-4-ol, and chlorhexidine on the physical-chemical properties of titanium surfaces, cell viability, proliferation, adhesion, and spreading of fibroblasts and osteoblasts in vitro. Titanium surfaces (Ti) were treated with Carvacrol (Cvc), Terpinen-4-ol (T4ol), Chlorhexidine (CHX), DMSO, and ultrapure water (Control group). Physical-chemical modifications were evaluated by surface wettability, the surface free energy (SFE) calculated from the contact angle values using the Owens-Wendt-Rabel-Kaeble (OWRK) equation, scanning electron microscopy (SEM) and energy dispersive spectrometry probe (EDS) system. Cells were seeded onto Ti-treated surfaces and incubated for 24 h and 72 h, then evaluated by Alamar blue assay and fluorescence microscopy. Surfaces treated with Cvc and T4ol showed the presence of Na, O, and Cl. All surfaces showed hydrophilic characteristics and SFE values between 5.5 mN/m and 3.4 mN/m. On the other hand, EDS peaks demonstrated the presence of O and Cl after CHX treatment. A reduction of cell viability and adhesion was noted on titanium surfaces treated with CHX after 24 and 72h. In conclusion, the results indicate that the decontamination with Cvc and T4ol on Ti surfaces does not alter the surface proprieties and allows an adequate interaction with cells involved in the re-osseointegration process such as fibroblasts and osteoblasts.

Effect of chemical and electrochemical decontamination protocols on single and multiple-used healing abutments: A comparative analysis of contact surface area, micro-gap, micro-leakage, and surface topography

INTRODUCTION

Although the combined use of chemical and electrochemical decontamination protocols can completely remove contaminants from the surfaces of one-time used healing abutments (HAs), their effectiveness in multiple-used HAs remains unknown. We aimed to investigate the effect of reused HAs frequency on the implant-HA contact surface area, micro-gap, microleakage, and surface topography following chemical and combined chemical and electrochemical decontamination protocols.

METHODS

Ninety bone level titanium implants were assembled with 90 bone level HAs, in which 80 contaminated HA samples were collected from human participants. The retrieved HAs were randomly divided into two groups according to the cleaning protocol: ultrasonication with 5.25% NaOCl solution for 15 min and steam autoclaving (group I); ultrasonication with 5.25% NaOCl solution for 15 min, followed by electrochemical cleaning and steam autoclaving (group II). The control group (group III) comprised 10 new unused HAs. The cleaning protocol was applied after each insertion as follows: (a) single-use and cleaning, (b) double-use and double cleaning cycles, (c) triple-use and triple cleaning cycles, and (d) more than triple-use and more than triple cleaning cycles. The contact surface area and micro-gap were assessed with micro-computed tomography scanning technique, microleakage test using 2% methylene blue staining, surface morphology with scanning electron microscopy, and surface elemental composition with energy-dispersive X-ray spectroscopy analysis.

RESULTS

Group Id exhibited the smallest contact surface area. The values of the micro-gap volumes and microleakage were significantly different (p < 0.001) in the descending order of Id > Ic > Ib > IId > Ia, IIa, and III. Morphological evaluation of Groups IIa, IIb, and IIc revealed that residual biological debris was optimally removed without altering their surface properties.

CONCLUSIONS

Chemical and electrochemical decontamination protocols are more effective than NaOCl cleaning methods, particularly for multiple consecutive uses with better decontamination levels, which decreases micro-gap volume and microleakage without surface alterations. Although the use of combined decontamination protocols for the contact surface area at the implant-HA interface showed comparable results with the control, change in the contact surface area was observed following the NaOCl cleaning methods. Therefore, titanium HA reuse can be considered in multiple times, if they are cleaned and sterilized using combined chemical and electrochemical decontamination protocols.

Titanium particles in peri-implantitis: distribution, pathogenesis and prospects

Peri-implantitis is one of the most important biological complications in the field of oral implantology. Identifying the causative factors of peri-implant inflammation and osteolysis is crucial for the disease's prevention and treatment. The underlying risk factors and detailed pathogenesis of peri-implantitis remain to be elucidated. Titanium-based implants as the most widely used implant inevitably release titanium particles into the surrounding tissue. Notably, the concentration of titanium particles increases significantly at peri-implantitis sites, suggesting titanium particles as a potential risk factor for the condition. Previous studies have indicated that titanium particles can induce peripheral osteolysis and foster the development of aseptic osteoarthritis in orthopedic joint replacement. However, it remains unconfirmed whether this phenomenon also triggers inflammation and bone resorption in peri-implant tissues. This review summarizes the distribution of titanium particles around the implant, the potential roles in peri-implantitis and the prevalent prevention strategies, which expects to provide new directions for the study of the pathogenesis and treatment of peri-implantitis.

Mechanical and Biological Properties of Titanium and Its Alloys for Oral Implant with Preparation Techniques: A Review

Dental implants have revolutionised restorative dentistry, offering patients a natural-looking and durable solution to replace missing or severely damaged teeth. Titanium and its alloys have emerged as the gold standard among the various materials available due to their exceptional properties. One of the critical advantages of titanium and its alloys is their remarkable biocompatibility which ensures minimal adverse reactions within the human body. Furthermore, they exhibit outstanding corrosion resistance ensuring the longevity of the implant. Their mechanical properties, including hardness, tensile strength, yield strength, and fatigue strength, align perfectly with the demanding requirements of dental implants, guaranteeing the restoration's functionality and durability. This narrative review aims to provide a comprehensive understanding of the manufacturing techniques employed for titanium and its alloy dental implants while shedding light on their intrinsic properties. It also presents crucial proof-of-concept examples, offering tangible evidence of these materials' effectiveness in clinical applications. However, despite their numerous advantages, certain limitations still exist necessitating ongoing research and development efforts. This review will briefly touch upon these restrictions and explore the evolving trends likely to shape the future of titanium and its alloy dental implants.

The Progress in Tribocorrosion Research (2010-21): Focused on the Orthopedics and Dental Implants

Tribocorrosion is an integration of two areas-tribology and corrosion. It can be defined as the material degradation caused by the combined effect of corrosion and tribological process at the material interfaces. Significant development has occurred in the field of tribocorrosion over the past years. This development is due to its applications in various fields, such as aerospace, marine, biomedical, and space. Focusing on biomedical applications, tribocorrosion finds its applications in the implants used in cardiovascular, spine, orthopedics, trauma, and dental areas. It was reported that around 7.2 million Americans are living with joint implants. Implant surgery is a traumatic and expensive procedure. Tribocorrosion can affect the lifespan of the implants, thus leading to implant failure and a potential cause of revision surgery. Hence, it is essential to understand how tribocorrosion works, its interaction with the implants, and what procedures can be implemented to protect materials from tribocorrosion. This paper discusses how tribocorrosion research has evolved over the past 11 years (2010-2021). This is a comprehensive overview of tribocorrosion research in biomedical applications.

Biomaterial engineering surface to control polymicrobial dental implant-related infections: focusing on disease modulating factors and coatings development

INTRODUCTION

Peri-implantitis is the leading cause of dental implant loss and is initiated by a polymicrobial dysbiotic biofilm formation on the implant surface. The destruction of peri-implant tissue by the host immune response and the low effectiveness of surgical or non-surgical treatments highlight the need for new strategies to prevent, modulate and/or eliminate biofilm formation on the implant surface. Currently, several surface modifications have been proposed using biomolecules, ions, antimicrobial agents, and topography alterations.

AREAS COVERED

Initially, this review provides an overview of the etiopathogenesis and host- and material-dependent modulating factors of peri-implant disease. In addition, a critical discussion about the antimicrobial surface modification mechanisms and techniques employed to modify the titanium implant material is provided. Finally, we also considered the future perspectives on the development of antimicrobial surfaces to narrow the bridge between idea and product and favor the clinical application possibility.

EXPERT OPINION

Antimicrobial surface modifications have demonstrated effective results; however, there is no consensus about the best modification strategy and in-depth information on the safety and longevity of the antimicrobial effect. Modified surfaces display recurring challenges such as short-term effectiveness, the burst release of drugs, cytotoxicity, and lack of reusability. Stimulus-responsive surfaces seem to be a promising strategy for a controlled and precise antimicrobial effect, and future research should focus on this technology and study it from models that better mimic clinical conditions.

Influence of eight debridement techniques on three different titanium surfaces: A laboratory study

OBJECTIVES

Debridement methods may damage implant surfaces. This in vitro study investigated eight debridement protocols across three implant surfaces to assess both biofilm removal and surface alterations.

MATERIAL AND METHODS

One hundred sixty commercially pure titanium discs were treated to simulate commercially available titanium implant surfaces-smooth, abraded and abraded and etched. Following inoculation with whole human saliva to create a mixed species biofilm, the surfaces were treated with eight debridement methods currently used for clinical peri-implantitis (n = 10). This included air abrasion using powders of glycine, sodium bicarbonate and calcium carbonate; conventional mechanical methods-piezoelectric scaler, carbon and stainless steel scalers; and a chemical protocol using 40% citric acid. Following treatment, remaining biofilm was analysed using scanning electron microscopy and crystal violet assays. For statistical analysis, ANOVA was applied (p < 0.05).

RESULTS

All debridement techniques resulted in greater than 80% reduction in biofilm compared with baseline, irrespective of the surface type. Glycine powder delivered through an air polishing system eliminated the most biofilm. Mechanical instruments were the least effective at eliminating biofilm across all surfaces and caused the greatest surface alterations. Citric acid was comparable with mechanical debridement instruments in terms of biofilm removal efficacy. Titanium surfaces were least affected by air abrasion protocols and most affected by mechanical methods.

CONCLUSIONS

Mechanical protocols for non-surgical debridement should be approached with caution. Glycine powder in an air polisher and 40% citric acid application both gave minimal alterations across all implant surfaces, with glycine the superior method in terms of biofilm removal.

In Situ and Ex Situ Raman Studies of Cysteine’s Behavior on a Titanium Surface in Buffer Solution

In this paper, surface-enhanced Raman spectroscopy (SERS) was used to investigate the adsorption process of cysteine (Cys). Studies were carried out in the presence of phosphate-buffered saline solution (PBS), at pH 7.4, and acidified to pH 5, 3, and 1, on the surface of Ti for implant application. In situ SERS spectra obtained for the Cys/Ti solution system, after 24 h of immersion time, indicated that the buffer solution strongly influences the adsorption behavior of Cys on the Ti surface. This results in a decrease in Cys adsorption on the Ti surface, in the range of pH 7.4 to 3. The strong interaction between a sulfur atom of Cys and a Ti surface was observed only at pH = 1, under strongly acidic conditions. In contrast, ex situ SERS spectra recorded for the same samples but in a dried Cys/Ti system show a completely different behavior of Cys on the Ti surface. Formation of a disulfide (S-S) bond has occurred as a result of the dimerization or aggregation of Cys molecules on the Ti surface. Detailed analysis of the adsorption behavior of Cys on the Ti surface can be very important in the preparation of bioactive materials (i.e., coated by organic layers).

Antimicrobial efficiency and cytocompatibility of different decontamination methods on titanium and zirconium surfaces

OBJECTIVES

The purpose of this study was to investigate the efficiency of different implant-decontamination methods regarding biofilm modification and potential cytotoxic effects. Therefore, the amount of biofilm reduction, cytocompatibility, and elementary surface alterations were evaluated after decontamination of titanium and zirconium surfaces.

MATERIAL AND METHODS

Titanium and zirconium disks were contaminated with a newly developed high-adherence biofilm consisting of six microbial species. Decontaminations were performed using titanium curette, stainless steel ultrasonic scaler (US), glycine (GPAP) and erythritol (EPAP) powder air-polishing, Er:YAG laser, 1% chlorhexidine (CHX), 10% povidone-iodine (PVI), 14% doxycycline (doxy), and 0.95% NaOCl solution. Microbiologic analysis was done using real-time qPCR. For assessment of cytocompatibility, a multiplex assay for the detection of cytotoxicity, viability, and apoptosis on human gingival fibroblasts was performed. X-ray photoelectron spectroscopy (XPS) was used to evaluate chemical alterations on implant surfaces.

RESULTS

Compared with untreated control disks, only GPAP, EPAP, US, and Er:YAG laser significantly reduced rRNA counts (activity) on titanium and zirconium (p < .01), whereas NaOCl decreased rRNA count on titanium (p < .01). Genome count (bacterial presence) was significantly reduced by GPAP, EPAP, and US on zirconium only (p < .05). X-ray photoelectron spectroscopy analyses revealed relevant re-exposure of implant surface elements after GPAP, EPAP, and US treatment on both materials, however, not after Er:YAG laser application. Cytocompatibility was impaired by CHX, PVI, doxy, and NaOCl. CHX and PVI resulted in the lowest viability and doxy in the highest apoptosis.

CONCLUSIONS

Within the limits of this in vitro study, air-polishing methods and ultrasonic device resulted in effective biofilm inactivation with surface re-exposure and favorable cytocompatibility on titanium and zirconium. Chemical agents, when applied on implant surfaces, may cause potential cytotoxic effects.

Bio-Tribocorrosion of Titanium Dental Implants and Its Toxicological Implications: A Scoping Review

Bio-tribocorrosion is a phenomenon that combines the essentials of tribology (friction, wear, and lubrication) and corrosion with microbiological processes. Lately, it has gained attention in implant dentistry because dental implants are exposed to wear, friction, and biofilm formation in the corrosive oral environment. They may degrade upon exposure to various microbial, biochemical, and electrochemical factors in the oral cavity. The mechanical movement of the implant components produces friction and wear that facilitates the release of metal ions, promoting adverse oro-systemic reactions. This review describes the bio-tribocorrosion of the titanium (Ti) dental implants in the oral cavity and its toxicological implications. The original research related to the bio-tribo or tribocorrosion of the dental implants was searched in electronic databases like Medline (Pubmed), Embase, Scopus, and Web of Science. About 34 studies included in the review showed that factors like the type of Ti, oral biofilm, acidic pH, fluorides, and micromovements during mastication promote bio-tribocorrosion of the Ti dental implants. Among the various grades of Ti, grade V, i.e., Ti6Al4V alloy, is most susceptible to tribocorrosion. Oral pathogens like Streptococcus mutans and Porphyromonas gingivalis produce acids and lipopolysaccharides (LPS) that cause pitting corrosion and degrade the TiO₂. The low pH and high fluoride concentration in saliva hinder passive film formation and promote metal corrosion. The released metal ions promote inflammatory reactions and bone destruction in the surrounding tissues resulting in peri-implantitis, allergies, and hyper-sensitivity reactions. However, further validation of the role of bio-tribocorrosion on the durability of the Ti dental implants and Ti toxicity is warranted through clinical trials.

Efficacy of combined chemical and electrochemical decontamination treatments on contaminated healing abutments and their effect on surface topography: An in vitro study

OBJECTIVE

To evaluate the efficacy of four decontamination protocols on contaminated healing abutments (HAs) and their effects on surface topography.

METHODS

Eighty contaminated single-use HA samples collected from human participants were stained with phloxine B and examined microscopically. The retrieved HAs were randomly divided into four test groups: (1) Autoclaving only (AU), (2) 5.25% sodium hypochlorite (NaOCl) + AU, (3) Electrochemical treatment (EC) + AU, (4) NaOCl + EC + AU, and positive control (contaminated without any treatment). Four new unused HAs served as negative controls (NC). The surface features were analyzed using stereo microscopy (SM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and optical profilometry.

RESULTS

The lowest decontamination efficacy was observed for the AU group. The NaOCl + AU and EC + AU groups effectively removed residual contamination, whereas EC + AU showed better decontamination results than NaOCl + AU. SM, SEM, and EDS analyses revealed the best decontamination efficacy in the combined NaOCl + EC + AU group compared to the other groups. Surface roughness (Sa), developed surface area ratio (Sdr), and texture-aspect ratio (Str) in AU, NaOCl + AU, EC + AU, and NaOCl + EC + AU groups were not statistically significant compared to the NC group.

CONCLUSIONS

The combination of NaOCl with subsequent EC can remove soft and hard deposits from the surface of HAs compared to NaOCl alone and EC alone, without altering the surface topography of HAs.

Effectiveness of Different Chemotherapeutic Agents for Decontamination of Infected Dental Implant Surface: A Systematic Review

Aim: To evaluate the most effective chemotherapeutic agent for decontamination of infected dental implants. Material and methods: A systematic electronic literature search in MEDLINE (PubMed) and Google scholar between January 2010 to December 2021 was carried out by using the PRISMA guidelines. A total of five studies related to chemical decontamination of the dental implant were evaluated. The search strategy was based on the PICOS framework. Randomized controlled trials (RCT’s) and cohort studies evaluating the effectiveness of different chemotherapeutic agents for the decontamination of dental implants were included in the study. The outcome variable examined was the most effective chemotherapeutic agent(s) for dental implant surface decontamination after comparing the chemotherapeutic agents used in the qualifying studies. Result: Out of the basic database of 1564 records, 1380 articles were excluded due to irrelevance, unavailability, and repetition. Furthermore, 134 articles were excluded from 184 studies for various reasons. After further filtration, 13 studies were shortlisted. Two investigators (SSA and SA) appraised the quality of the selected studies using the risk of bias assessment tool. After excluding eight studies, five articles were finally included in the present systematic review. Conclusion: The data reported for the efficacy of chemotherapeutic agents in cleaning contaminated titanium surfaces are scarce, thus it is not possible to draw a definite conclusion. However, chlorhexidine (CHX) (0.2%, 0.12%), citric acid (40%) and sodium hypochlorite (1%) are the most commonly used chemotherapeutic agents; amongst them, citric acid showed the highest potential for biofilm removal from the contaminated implant surface. All three agents [CHX (0.2%, 0.12%), citric acid (40%), and sodium hypochlorite (1%)] can be recommended as therapeutic agents along with their curbs.

The Effects of Ultrasonic Scaling and Air-Abrasive Powders on the Decontamination of 9 Implant-Abutment Surfaces: Scanning Electron Analysis and In Vitro Study

(1) Background: The aim of this study is to understand from a microscopic point of view whether bicarbonate air-abrasive powders associated with ultrasonic instruments can decontaminate nine different surfaces used for the abutment/implant junction. Fibroblast growth was carried out on decontaminated surface in order to understand if there are significative differences in terms of biocompatibility. (2) Methods: After taking samples of patient plaque, nine different surfaces were contaminated and analyzed by SEM, then their wettability was evaluated. Fibroblasts were cultured on the decontaminated surfaces to understand their ability to establish a connective tissue seal after decontamination. The results were analyzed from a statistical point of view to hypothesize a mathematical model capable of explaining the properties of the surfaces. (3) Results: A negative correlation between roughness and contamination has been demonstrated, whereas a weak correlation was observed between wettability and decontamination capacity. All surfaces were topographically damaged after the decontamination treatment. Grade 5 titanium surfaces appear tougher, whereas anodized surfaces tend to lose the anodizing layer. (4) Conclusions: further studies will be needed to fully understand how these decontaminated surfaces affect the adhesion, proliferation and differentiation of fibroblasts and osteoblasts.

Relevant Aspects of Piranha Passivation in Ti6Al4V Alloy Dental Meshes

Passivation of titanium alloy dental meshes cleans their surface and forms a thin layer of protective oxide (TiO2) on the surface of the material to improve resistance to corrosion and prevent release of ions to the physiological environment. The most common chemical agent for the passivation process of titanium meshes is hydrochloric acid (HCl). In this work, we introduce the use of Piranha solution (H2SO4 and H2O2) as a passivating and bactericidal agent for metallic dental meshes. Meshes of grade 5 titanium alloy (Ti6Al4V) were tested after different treatments: as-received control (Ctr), passivated by HCl, and passivated by Piranha solution. Physical-chemical characterization of all treated surfaces was carried out by scanning electron microscopy (SEM), confocal microscopy and sessile drop goniometry to assess meshes’ topography, elemental composition, roughness, wettability and surface free energy, that is, relevant properties with potential effects for the biological response of the material. Moreover, open circuit potential and potentiodynamic tests were carried out to evaluate the corrosion behavior of the differently-treated meshes under physiological conditions. Ion release tests were conducted using Inductively Coupled Plasma mass spectrometry (ICP-MS). The antibacterial activity by prevention of bacterial adhesion tests on the meshes was performed for two different bacterial strains, Pseudomonas aeruginosa (Gram-) and Streptococcus sanguinis (Gram+). Additionally, a bacterial viability study was performed with the LIVE/DEAD test. We complemented the antibacterial study by counting cells attached to the surface of the meshes visualized by SEM. Our results showed that the passivation of titanium meshes with Piranha solution improved their hydrophilicity and conferred a notably higher bactericidal activity in comparison with the meshes passivated with HCl. This unique response can be attributed to differences in the obtained nanotextures of the TiO2 layer. However, Piranha solution treatment decreased electrochemical stability and increased ion release as a result of the porous coating formed on the treated surfaces, which can compromise their corrosion resistance. Framed by the limitations of this work, we conclude that using Piranha solution is a viable alternative method for passivating titanium dental meshes with beneficial antibacterial properties that merits further validation for its translation as a treatment applied to clinically-used meshes.

Citric Acid in the Passivation of Titanium Dental Implants: Corrosion Resistance and Bactericide Behavior

The passivation of titanium dental implants is performed in order to clean the surface and obtain a thin layer of protective oxide (TiO2) on the surface of the material in order to improve its behavior against corrosion and prevent the release of ions into the physiological environment. The most common chemical agent for the passivation process is hydrochloric acid (HCl), and in this work we intend to determine the capacity of citric acid as a passivating and bactericidal agent. Discs of commercially pure titanium (c.p.Ti) grade 4 were used with different treatments: control (Ctr), passivated by HCl, passivated by citric acid at 20% at different immersion times (20, 30, and 40 min) and a higher concentration of citric acid (40%) for 20 min. Physical-chemical characterization of all of the treated surfaces has been carried out by scanning electronic microscopy (SEM), confocal microscopy, and the 'Sessile Drop' technique in order to obtain information about different parameters (topography, elemental composition, roughness, wettability, and surface energy) that are relevant to understand the biological response of the material. In order to evaluate the corrosion behavior of the different treatments under physiological conditions, open circuit potential and potentiodynamic tests have been carried out. Additionally, ion release tests were realized by means of ICP-MS. The antibacterial behavior has been evaluated by performing bacterial adhesion tests, in which two strains have been used: Pseudomonas aeruginosa (Gram-) and Streptococcus sanguinis (Gram+). After the adhesion test, a bacterial viability study has been carried out ('Life and Death') and the number of colony-forming units has been calculated with SEM images. The results obtained show that the passivation with citric acid improves the hydrophilic character, corrosion resistance, and presents a bactericide character in comparison with the HCl treatment. The increasing of citric acid concentration improves the bactericide effect but decreases the corrosion resistance parameters. Ion release levels at high citric acid concentrations increase very significantly. The effect of the immersion times studied do not present an effect on the properties.

Impact of tribocorrosion and titanium particles release on dental implant complications - A narrative review

Titanium particles as a product of degradation have been detected in periimplant oral tissues and it has been assumed that implants were the source of these particles. Periimplantitis sites had higher concentrations of particles in comparison to healthy implant sites. Several factors have been identified in the degradation of dental implant surface, such as mechanical wear, contact with chemical agents, and the effects of biofilm adhesion. Titanium particles silently prompt the immune-system activation and generate a pro-inflammatory response in macrophages, T lymphocytes and monocytes. During the activation, inflammatory cytokines are released including, granulocyte-macrophage colony-stimulating factor (GM-CSF), prostaglandin, and TNF-α, IL-1β, IL-6. The nanoparticles depict unique features such as high level of biological reactivity and potentially harmful compared to microparticles since they have a relatively greater surface area to volume ratio. Allergic response to titanium as a cause of implant failure has not been well documented. Evidence demonstrating biological complication due to titanium particles release includes peri-implant tissue inflammation that lead terminally to implant loss. There is a biological probability for a relation between the presence of titanium particles and ions, biological complication, and corrosion, but there is no justifiable evidence for unidirectional series of causative actions.

Passive Layers and Corrosion Resistance of Biomedical Ti-6Al-4V and β-Ti Alloys

The high specific strength, good corrosion resistance, and great biocompatibility make titanium and its alloys the ideal materials for biomedical metallic implants. Ti-6Al-4V alloy is the most employed in practical biomedical applications because of the excellent combination of strength, fracture toughness, and corrosion resistance. However, recent studies have demonstrated some limits in biocompatibility due to the presence of toxic Al and V. Consequently, scientific literature has reported novel biomedical β-Ti alloys containing biocompatible β-stabilizers (such as Mo, Ta, and Zr) studying the possibility to obtain similar performances to the Ti-6Al-4V alloys. The aim of this review is to highlight the corrosion resistance of the passive layers on biomedical Ti-6Al-4V and β-type Ti alloys in the human body environment by reviewing relevant literature research contributions. The discussion is focused on all those factors that influence the performance of the passive layer at the surface of the alloy subjected to electrochemical corrosion, among which the alloy composition, the method selected to grow the oxide coating, and the physicochemical conditions of the body fluid are the most significant.

The unfavorable role of titanium particles released from dental implants

Titanium is considered to be a metal material with the best biological safety. Studies have proved that the titanium implanted in the bone continuously releases titanium particles (Ti particles), significantly increasing the total titanium content in human body. Generally, Ti particles are released slowly without causing a systemic immune response. However, the continuous increased local concentration may result in damage to the intraepithelial homeostasis, aggravation of inflammatory reaction in the surrounding tissues, bone resorption and implant detachment. They also migrate with blood flow and aggregate in the distal organ. The release of Ti particles is affected by the score of the implant surface structure, microenvironment wear and corrosion, medical operation wear, and so on, but the specific mechanism is not clear. Thus, it difficult to prevent the release completely. This paper reviews the causes of the Ti particles formation, the damage to the surrounding tissue, and its mechanism, in particular, methods for reducing the release and toxicity of the Ti particles.

Optimizing citric acid protocol to control implant-related infections: An in vitro and in situ study

OBJECTIVE

The present study aimed to establish an optimized protocol for biofilm removal from titanium (Ti) surfaces using citric acid (CA) solutions.

BACKGROUND

Biofilm accumulation is the main factor to trigger peri-implant infections and to increase the risk of treatment failures. Although CA has been suggested as the anti-infective agent with highest potential for biofilm removal on Ti, there is no consensus that CA could improve the anti-infective treatment and its effect.

METHODS

Physical and chemical alterations, electrochemical behavior, cytotoxicity, and antimicrobial effect of CA on Ti discs were evaluated using four concentrations (1, 10, 20, and 40%) and two application methods (immersion and rubbing). Negative control using 0.9% NaCl was used in all experiments. To evaluate whether different application times can have similar response, polymicrobial biofilm (microcosm model) was formed on Ti and treated with CA for 1, 2, 4, and 8 min. An in situ study was conducted to verify whether the established protocol is equally effective in biofilms formed on machined and sandblasted, large-grit, and acid-etched (SLA) Ti surfaces.

RESULTS

CA 40% induced significantly higher surface alterations observed by confocal images and profilometry. In general, rubbing protocol decreased the surface roughness and increased the wettability (p < 0.05), exhibiting better surface cleaning by biofilm removal. CA 10% presented no indirect cytotoxicity and, when applied by rubbing for 8 min, presented proper in vitro antibacterial action and potential corrosion inhibition. When CA 10% was rubbed on Ti surfaces for 4 min, it displayed optimum cleaning ability as 8 min, working equally to remove in situ biofilm on machined and SLA surfaces.

CONCLUSIONS

The application of CA 10% by rubbing for at least 4 min demonstrated to be a promising protocol to eliminate biofilms formed in smooth and rougher surfaces, which could improve implant-related infection therapies.

Residual decontamination chemical agents negatively affect adhesion and proliferation of osteoblast-like cells on implant surface

Purpose

To investigate the influence of implant surface decontaminated and uncontaminated on osteoblast-like cell adhesion and proliferation

Materials and methods

Commercially available implants of different brands and surface characteristics were selected: Biomet 3i® Nanotite (NT) and Osseotite (OT), Straumann® SLActive (SLA), and Neodent® Acqua Drive (ACQ) and Neoporos Drive CM (CM). Physical and chemical properties of the implants were investigated by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and wettability analysis (WETT). Implants were previously contaminated with Aggregatibacter actinomycetemcomitans strains; after that, samples were decontaminated by different chemical methods. Decontaminated (test group; n = 15/type of implant) and uncontaminated (control group; n = 5/type of implant) samples were analyzed according to the number of human osteoblastic osteosarcoma cells (Saos-2) adhered on the implant surface after 24 h and 72 h in SEM images.

Results

ACQ was found to be highly hydrophilic, and NT was the most hydrophobic implant. Increased variation of Saos-2 cell adhesion and proliferation were observed on all test and control groups. Controversially, at the proliferation analysis in 72 h, CM implant was the only implant that showed no significant difference between test and group (p = 0.2833; Tukey’s multiple comparisons test). NT implants showed the greater value of cell proliferation when compared with all types of implant surface (p = 0.0002; Tukey’s multiple comparisons test).

Conclusions

These findings suggest that decontaminated surfaces were able to impair the counting of osteoblast-like cell adhesion and proliferation.

Peri-Implant Diseases: Diagnosis, Clinical, Histological, Microbiological Characteristics and Treatment Strategies. A Narrative Review

Since the use of dental implants is continuously increasing, it is imperative for dental practitioners to understand the nature and treatment of peri-implant diseases. The purpose of this manuscript is to comprehensively review peri-implant diseases, their characteristics, as well as their non-surgical and surgical treatment. To that end, the current literature was searched and a narrative review was conducted. It is essential that the case definitions described in the 2017 World Workshop on the Classification of Periodontal and Peri-implant Diseases and Conditions are used to diagnose and classify peri-implant health, peri-implant mucositis and peri-implantitis. While recent epidemiologic studies on peri-implant diseases exist, there is great heterogeneity in the definition of these conditions. Several risk factors and indicators are reported in the literature, with smoking and diabetes being the most universally accepted. In peri-implant mucositis, non-surgical treatment seems to be sufficient. However, for the treatment of peri-implantitis, a surgical approach, which includes open-flap debridement, apically positioned flap and guided bone regeneration, is considered more appropriate. A great variety of adjuncts to mechanical treatment have been reported with controversial results. Finally, studies comparing results from different peri-implantitis treatments are warranted in randomized controlled clinical trials in order to provide stronger evidence-based approaches.

The influence of implant surface roughness on decontamination by antimicrobial photodynamic therapy and chemical agents: A preliminary study in vitro

BACKGROUND

The aim of this preliminary study was to analyze the effectiveness of three different protocols of decontamination on five commercial moderate rough implants.

MATERIAL AND METHODS

The types of implants investigated were: Neoporos Drive CM (CM; Neodent®), Drive CM Acqua (ACQ; Neodent®), SLActive (SLA; Straumann®), Osseotite (OT; Biomet 3i®) and Nanotite (NT; Biomet 3i®). Implant surface properties (n = 2/type of implant; control groups) were analyzed by scanning electron microscopy (SEM) images to determine surface roughness parameters (SRP) and energy disperse X-ray spectrometry to determine the chemical composition. Implants were then inoculated with Aggregatibacter actinomycetencomitans in vitro (n = 6/type of implant;experimental groups) and the contaminated areas were determined in SEM images (500x magnifications). Decontamination of implants was performed in duplicate by three protocols: antimicrobial photodynamic therapy (aPDT), EDTA associated with citric acid (EDTA + CA) and 0.12 % chlorhexidine (CHX). The remaining contaminated area (rCtA) was determined in SEM images (500x magnifications). All quantitative analysis through SEM images were analyzed in ImageJ® software for two-dimensional parameters.

RESULTS

No significant differences were found in SRP among implants (control group), except for Rv (lowest valley) between SLA vs. OT (p=0.0031; Kruskal Wallis post hoc Dunn). NT implants showed highest contaminated area vs. ACQ implants (68.19 % ± 8.63 % and 57.32 % ± 5.38 %, respectively; p = 0.0016, Tukey's test). SRP after decontamination showed statistical difference for Ra (arithmetical mean deviation) for all decontamination groups when compared to control (p < 0.05; ANOVA with post-hoc Tukey's multiple comparisons test), only CM implants showed statistical difference when compared decontamination protocols to control with highest modification of SRP for EDTA + AC group. For decontamination analysis, for applicability of different protocols in the same type of implant, only SLA showed statistical significant difference for aPDT vs. EDTA + CA (p = 0.0114; ANOVA with post-hoc Tukey's multiple comparisons test) with lowest rCTA for aPDT, however for ACQ implants the aPDT showed lowest rCTA with no statistical difference (p > 0.05; ANOVA with post-hoc Tukey's multiple comparisons test). No statistical difference was observed between the decontamination protocols at other implant types.

CONCLUSION

It can be suggested that the chemical-physical characteristics of dental implants can be effected by the process of contamination and decontamination by aPDT and chemical agents.

Effectiveness and surface changes of different decontamination protocols at smooth and minimally rough titanium surfaces

BACKGROUND

The objective of this study is to evaluate titanium decontamination after different protocols while assessing changes in surface roughness, chemical composition, and wettability.

METHODS

Ninety-six smooth (S) and 96 minimally rough (R) titanium microimplants were used. Pristine microimplants were reserved for negative control (S-nC/R-nC, n = 9), while the remaining microimplants were incubated in Escherichia coli culture. Non-decontaminated microimplants were used as positive control (S-pC/R-pC, n = 3). The other microimplants were divided into seven different decontamination protocols (12 S/R per group): 24% EDTA, 2% chlorhexidine (CHL), gauze soaked in 2% chlorhexidine (GCHL), gauze soaked in ultrapure water (GMQ), scaling (SC), titanium brush (TiB), and implantoplasty (IP). Contaminated areas were assessed by scanning electron microscope images, chemical composition by energy dispersive X-ray spectroscopy, wettability by meniscus technique, and roughness by an optical profiler.

RESULTS

Higher residual bacteria were observed in R-pC compared with S-pC (P <0.0001). When comparing S and R with their respective pC groups, the best results were obtained with GCHL, SC, TiB, and IP, with no difference between these protocols (P >0.05). Changes in surface roughness were observed after all treatments, with S/R-IP presenting the smoother and a less hydrophilic surface (P <0.05). Apart from IP protocol, all the other groups presented a more hydrophilic surface in R than in S microimplants (P <0.003). All decontamination protocols resulted in a lower percentage of superficial Ti when compared with S/R-nC (P <0.002).

CONCLUSIONS

All decontamination protocols resulted in changes in roughness, wettability, and chemical composition, but GCHL, SC, TiB, an IP presented the best decontamination outcomes.

Management of Peri-Implantitis Lesions without the Use of Systemic Antibiotics: A Systematic Review

BACKGROUND

This systematic review aims to assess the current evidence on the efficacy of surgical and non-surgical debridement techniques in the treatment of peri-implantitis lesions without the use of any antimicrobials.

METHOD

Five electronic databases (MEDLINE, Pubmed, Scopus, CINAHL and Cochrane) were used, alongside hand searches, to find relevant articles. Full-text articles that were randomised controlled trials, published in the English language from 2011 onwards without pre-operative, peri-operative and post-operative antibiotic usage were included. The study was conducted according to the latest Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA)-P protocols, the latest Cochrane Risk of Bias tool and each investigated intervention was evaluated using the grading of recommendation, assessment, development and evaluation (GRADE) system.

RESULTS

The search yielded 2718 results. After initial screening, 38 full-text articles were assessed for eligibility. From these, 11 studies satisfied all inclusion criteria. These 11 articles described six non-surgical and five surgical debridement therapies. Most articles were classified as having either a high risk of bias or presenting with some concerns. Small sample sizes, in combination with this risk of bias, meant that all interventions were adjudged to be of either low or very low quality of evidence.

CONCLUSION

While all investigated modalities displayed some sort of efficacy, this review suggests that a surgical approach may be best suited to treating peri-implantitis lesions in the absence of antibiotic therapy. Despite this weak indication, further research is required in this field.

The Prevention of Implant Surface Alterations in the Treatment of Peri-Implantitis: Comparison of Three Different Mechanical and Physical Treatments

The surgical treatment of peri-implantitis is currently based on the removal of biofilms from the implant surface by primary means of mechanical and physical treatments. However, such approaches often determine some alterations of the implant surface with detrimental effects on re-osseointegration. This study aims to evaluate the effects of four different mechanical and physical treatments on titanium samples with moderately rough surface. Air powder abrasion (AP) with glycine powder, a titanium brush (TB) and a diode laser at 3 W (L3) and 4 W (L4) were tested. Surface morphology, roughness and chemical composition were then assessed by scanning electron microscope (SEM), white light interferometer and X-ray photoelectron spectroscopy (XPS), respectively. The microscopic analysis revealed significant alterations in surface morphology on TB samples, while AP and L3 had only a minor or null impact. L4 samples revealed signs of overheating due to the excessive power. Nevertheless, the overall roughness of the samples was not significantly altered in terms of roughness parameters. Similarly, surface chemical composition was not significantly affected by the treatments. Among the treatments tested in this study, air powder abrasion with glycine powder and 3 W diode laser had the lowest impact on surface physicochemical properties.

Q-Switch Nd:YAG Laser-Assisted Elimination of Multi-Species Biofilm on Titanium Surfaces

(1) Background: The relatively high prevalence of peri-implantitis (PI) and the lack of a standard method for decontamination of the dental implant surface have pushed us to conduct further research in the field. Bacterial biofilms were found to play a primordial role in the etiology of PI. Therefore, the aim is to evaluate the efficacy of a laser-assisted elimination of biofilm protocol in the removal of a multi-species biofilm on titanium surfaces. (2) Methods: In total, 52 titanium discs (grade 4) were used. The study group consisted of 13 titanium disks contaminated with multi-species biofilms and subsequently irradiated with the laser (T + BF + L). The control groups consisted of the following types of titanium disks: 13 contaminated with multi-species biofilms (T + BF), 13 sterile and irradiated (T + L), 13 sterile and untreated (T). Q-Switch Nd:YAG laser Irradiation parameters were the following: energy density equal to 0.597 J/cm² per pulse, power equal to 270 milliwatt per pulse, 2.4 mm of spot diameter, and 10 Hz repetition rate for pulse duration of six nanoseconds (ns). The laser irradiation was made during 2 s of total time in non-contact and at 0.5 mm away from the titanium disc surface. After treatment, presence of biofilms on the disks was evaluated by staining with crystal violet (CV), which was measured as optical density at six hundred thirty nm, and statistical analyses were done. (3) Results: the optical density values were 0.004 ± 0.004 for the study group T + BF + L, 0.120 ± 0.039 for group T + BF, 0.006 ± 0.003 for group T + L, and 0.007 ± 0.007 for group T. For the study group, laser treatment resulted in a total elimination of the biofilm, with mean values statistically significantly lower than those of contaminated titanium surfaces and similar to those of sterile titanium surfaces. (4) Conclusions: Our irradiation protocol provided a significant elimination of the multi-species biofilm on titanium surfaces. Laser treated titanium surfaces were biofilm-free, similar to the sterile ones.

Análise físico-química da superfície de titânio após tratamento químico de descontaminação com clorexidina: estudo in vitro

Resumo Introdução Tratamentos têm sido propostos para a peri-implantite com o objetivo de descontaminar a superfície dos implantes, removendo microrganismos que podem estar associados à doença. Objetivo O objetivo deste estudo foi avaliar a ação in vitro de diferentes métodos de aplicação de digluconato de clorexidina (CLX) na descontaminação de discos de titânio (Ti) com microtopografia e seu efeito físico-químico sobre a superfície. Material e método Vinte discos de Ti foram expostos a inóculo de Escherichia coli por 24 horas. Foram distribuídos em quatro grupos de descontaminação (n=5): 1 - um minuto de exposição à solução de CLX 0,12%; 2 - dois minutos de exposição à solução de CLX 0,12%; 3 - esfregaço durante um minuto com gel de CLX 1%; 4 - esfregaço durante um minuto com gel de CLX 2%. O produto de cada disco foi diluído e plaqueado individualmente. Após 24 horas, realizou-se contagem das unidades de colônias formadas (UFC). Resultado O grupo com o menor número de crescimento de UFC foi o grupo 4 (0,20±0,37), com apenas UFC em uma das amostras. Seguido do grupo 2 (0,40±0,73), grupo 1 (18,60±33,96). O grupo 3 apresentou as maiores quantidades de UFC (36,07±41,39). Em todas as amostras, foi possível observar uma diminuição estatisticamente significante da concentração superficial de Ti, assim como um aumento de Oxigênio. Conclusão Pode-se concluir que o uso de CLX gel a 2% em superfícies de Ti com microtopografia contaminadas com E. coli propicia a eliminação das UFC e que sua aplicação resulta em diminuição do percentual de Ti e aumento do teor de O.

Antibacterial Activity and Impact of Different Antiseptics on Biofilm-Contaminated Implant Surfaces

Several antiseptic agents have been proposed for the treatment of peri-implantitis as a complementary therapeutic strategy in addition to mechanical devices. The aim of this study was to compare six different antiseptics, as well as alternative formulations of the same chemical agent, with respect to their decontamination efficacy and impact on chemical properties of the implant surface. Titanium disks with a micro-rough surface, previously contaminated with Porphyromonas gingivalis and Streptococcus mutans biofilms, were treated for 2 min with different antiseptics (liquid sodium hypochlorite 5.25%, gel sodium hypochlorite 5.25%, liquid chlorhexidine 0.2%, gel chlorhexidine 1%, gel citric acid 40%, and gel orthophosphoric acid 37%) or sterile saline solution (control) and their antibacterial activity as well as their ability to remove biofilm were assessed by viable bacterial count and scanning electron microscopy, respectively. Spectroscopic analysis was also performed on non-contaminated disks after exposure to the antiseptics, in order to detect any change in the elemental composition of the titanium surface. All the antimicrobial formulations examined were effective against P. gingivalis and S. mutans biofilms. SEM analysis revealed however that liquid sodium hypochlorite 5.25% was more effective in dissolving biofilm residues. Spectroscopic analysis detected traces of the antiseptics, probably due to insufficient rinsing of the titanium surfaces. In conclusion, since gel formulations of these antiseptic agents possessed a similar antibacterial activity to the liquid formulations, these may be proposed as alternative treatments given their properties to avoid overflows and increase contact time without significant side effects on the bone.

Host response and peri-implantitis

Considering the absence of predictable and effective therapeutic interventions for the treatment of peri-implantitis, scientific evidence concerning the host response profile around dental implants could be important for providing in the future a wider preventive and/or therapeutic window for this peri-implant lesion, indicating biomarkers that provide quantifiable measure of response to peri-implant therapy. Moreover, a better knowledge of pattern of host osteo-immunoinflammatory modulation in the presence of peri-implantitis could either benefit the early diagnostic of the disease or to cooperate to prognostic information related to the status of the peri-implant breakdown. Finally, new evidences concerning the host profile of modulators of inflammation and of osseous tissue metabolism around dental implants could explain the individual susceptibility for developing peri-implant lesions, identifying individuals or sites with increased risk for peri-implantitis. The focus of this chapter was, based on a systematically searched and critically reviewed literature, summarizing the existing knowledge in the scientific research concerning the host osteo-immunoinflammatory response to the microbiological challenge related to periimplantitis.

Thermal Testing of Titanium Implants and the Surrounding Ex-Vivo Tissue Irradiated With 9.3um CO2 Laser

PURPOSE

To measure the temperature rise and surface damage of titanium dental implants and the surrounding tissue in a pig jaw during 9.3-μm carbon dioxide (CO2) laser irradiation at various durations of time.

MATERIALS AND METHODS

Thermal analysis tests were performed on 12 implants with the same surface. Twelve implants mounted alone or in pig jaws were laser-irradiated with a 9.3-μm CO2 laser using 3 different power settings. The temperature of the implant body and the proximal tissues was measured with a J-Type Thermocouple after being laser-irradiated with 3 different power setting for 30, 60 seconds, and 2 minutes. Scanning electron microscope (SEM) and digital microscope images were also taken of the all the implants before and after laser irradiation to detect the presence or absence of surface damage.

RESULTS

Temperature analysis showed that in all cases the implant and the proximal tissue temperatures remained around the start temperatures of the implant and tissues with fluctuations of ±3°C but never reached the upper threshold of 44°C, the temperature at which thermal injury to bone has been reported. Digital and SEM images that were taken of the implants showed an absence of surface damage at the cutting speed of 20% (0.7 W); however, cutting speeds of 30% to 100% (1.0-4.2 W) did yield surface damage.

CONCLUSIONS

Laser irradiation of titanium implant surfaces using a 9.3-μm carbon dioxide laser with an average power of 0.7 W showed no increase in thermal temperature of the implant body and tissue temperatures as well as no evidence of implant surface damage.

Hydroxyl radicals generated by hydrogen peroxide photolysis recondition biofilm-contaminated titanium surfaces for subsequent osteoblastic cell proliferation

Titanium dental implants have been successfully used for decades; however, some implants are affected by peri-implantitis due to bacterial infection, resulting in loss of supporting bone. This study aimed to evaluate the effect of an antimicrobial chemotherapy employing H₂O₂ photolysis-developed to treat peri-implantitis-on biofilm-contaminated titanium surfaces in association with osteoblastic cell proliferation on the treated surface. Titanium discs were sandblasted and acid-etched, followed by contamination with a three-species biofilm composed of Porphyromonas gingivalis, Fusobacterium nucleatum, and Streptococcus mitis. This biofilm model was used as a simplified model of clinical peri-implantitis biofilm. The discs were subjected to ultrasound scaling, followed by H₂O₂ photolysis, wherein 365-nm LED irradiation of the disc immersed in 3% H₂O₂ was performed for 5 min. We analysed proliferation of mouse osteoblastic cells (MC3T3-E1) cultured on the treated discs. Compared with intact discs, biofilm contamination lowered cell proliferation on the specimen surface, whereas H₂O₂ photolysis recovered cell proliferation. Thus, H₂O₂ photolysis can recover the degraded biocompatibility of biofilm-contaminated titanium surfaces and can potentially be utilised for peri-implantitis treatment. However, to verify the findings of this study in relation to clinical settings, assessment using a more clinically relevant multi-species biofilm model is necessary.

Titanium particles generated during ultrasonic scaling of implants

BACKGROUND

There is growing concern that titanium particles may play a role in peri-implant breakdown. Ultrasonic scalers are routinely used in the debridement of peri-implant lesions. This in vitro study is designed to evaluate if titanium particles are produced when an ultrasonic scaler is used on an implant.

METHODS

New sandblasted, large grit, acid etched (SLA) coated implants were subjected to ultrasonic scaling with stainless steel, titanium, and PEEK plastic tips. The implants were placed in a holding device and the ultrasonic scaler was positioned on the SLA surface under 25 grams of pressure. The implants were subjected to 30 scaling motions. The ultrasonic coolant water was collected and the number of metallic particles were counted under a light microscope. The particles were confirmed to be titanium via elemental analysis. The implants were visually evaluated for damage to the SLA coating.

RESULTS

No metallic particles were detected in the water supplied to the ultrasonic scalers (passive control). Metallic particles were detected when implants were subjected to the ultrasonic coolant water only without the scaler tip touching the implant (active control). All implants that were scaled produced metallic particles and showed easily detectable damage to the SLA layer.

CONCLUSIONS

All ultrasonic scaling caused the production of titanium particles and caused damage to the SLA coating of the implant. Ultrasonic scalers should be used with great caution in the treatment of peri-implant conditions and care should be taken to not touch the SLA surface of the implant.

Potential Causes of Titanium Particle and Ion Release in Implant Dentistry: A Systematic Review

Implant surface characteristics, as well as physical and mechanical properties, are responsible for the positive interaction between the dental implant, the bone and the surrounding soft tissues. Unfortunately, the dental implant surface does not remain unaltered and changes over time during the life of the implant. If changes occur at the implant surface, mucositis and peri-implantitis processes could be initiated; implant osseointegration might be disrupted and bone resorption phenomena (osteolysis) may lead to implant loss. This systematic review compiled the information related to the potential sources of titanium particle and ions in implant dentistry. Research questions were structured in the Population, Intervention, Comparison, Outcome (PICO) framework. PICO questionnaires were developed and an exhaustive search was performed for all the relevant studies published between 1980 and 2018 involving titanium particles and ions related to implant dentistry procedures. Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines were followed for the selection and inclusion of the manuscripts in this review. Titanium particle and ions are released during the implant bed preparation, during the implant insertion and during the implant decontamination. In addition, the implant surfaces and restorations are exposed to the saliva, bacteria and chemicals that can potentially dissolve the titanium oxide layer and, therefore, corrosion cycles can be initiated. Mechanical factors, the micro-gap and fluorides can also influence the proportion of metal particles and ions released from implants and restorations.

The effect of manufacturing techniques on custom-made titanium cranioplasty plates: A pilot study

OBJECTIVE

This study investigated the effect of varying techniques on the surface characteristics of pressed titanium cranioplasty plates, commonly manufactured in laboratory practice. The aim was to highlight the variety of techniques currently used, assess these methods of manufacture and produce manufacturing recommendations.

METHODS

A questionnaire identified manufacturing methods commonly used by maxillofacial prosthetists. The plate surfaces were examined using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectrometry. The surface differences and titanium compositions were statistically analysed.

RESULTS

Bead blasting with aluminium oxide (Al₂O₃) showed a significant decrease (p < 0.001) in titanium surface composition, replaced by a large aluminium content. Trimming tool choice had a significant impact (p = 0.001) on surface contamination by smoothing wheel material deposition; however passivation and anodising techniques had no significant effect (p = 0.293 and p = 0.257, respectively) on the surface composition or roughness of titanium samples.

CONCLUSIONS

A large range of manufacturing techniques of titanium cranioplasty plates was confirmed and significant differences were found. Amongst other recommendations, bead blasting with Al₂O₃ is not recommended for commercially pure titanium implant surface finishing due to aluminium contamination. The recommendations outlined will minimise manufacturing time, reduce risk of complication (thus costs) and unify methods to enable a safe, reliable treatment.

Can degradation products released from dental implants affect peri-implant tissues?

This study aimed to assess the literature available on the effects, on peri-implant tissues, of degradation products released from dental implants as a consequence of therapeutic treatment for peri-implantitis and/or of wear-corrosion of titanium. A literature review of the PubMed medline database was performed up to December 31, 2016. The following search terms were used: "titanium wear and dental implant"; "titanium corrosion and dental implant"; "bio-tribocorrosion"; "peri-implantitis"; "treatment of peri-implantitis"; "titanium particles release and dental implant"; and "titanium ion release and dental implant". The keywords were applied to the database in different combinations without limits of time period or type of work. In addition, the reference lists of relevant articles were searched for further studies. Seventy-nine relevant scientific articles on the topic were retrieved. The results showed that pro-inflammatory cytokines, infiltration of inflammatory response cells and activation of the osteoclasts activity are stimulated in peri-implant tissues in the presence of metal particles and ions. Moreover, degenerative changes were reported in macrophages and neutrophils that phagocytosed titanium microparticles, and mutations occurred in human cells cultured in medium containing titanium-based nanoparticles. Debris released from the degradation of dental implants has cytotoxic and genotoxic potential for peri-implant tissues. Thus, the amount and physicochemical properties of the degradation products determine the magnitude of the detrimental effect on peri-implant tissues.

Implant decontamination with phosphoric acid during surgical peri-implantitis treatment: a RCT

Background

Peri-implantitis is known as an infectious disease that affects the peri-implant soft and hard tissue. Today, scientific literature provides very little evidence for an effective intervention protocol for treatment of peri-implantitis. The aim of the present randomized controlled trial is to evaluate the microbiological and clinical effectiveness of phosphoric acid as a decontaminating agent of the implant surface during surgical peri-implantitis treatment.

Methods

Peri-implantitis lesions were treated with resective surgical treatment aimed at peri-implant granulation tissue removal, bone recontouring, and pocket elimination. Fifty-three implant surfaces in 28 patients were mechanically cleaned and treated with either 35% phosphoric etching gel (test group) or sterile saline (control group). Microbiological samples were obtained during surgery; clinical parameters were recorded at baseline and at 3 months after treatment. Data were analyzed using multi-variable linear regression analysis and multilevel statistics.

Results

Significant immediate reductions in total anaerobic bacterial counts on the implant surface were found in both groups. Immediate reduction was greater when phosphoric acid was used. The difference in log-transformed mean anaerobic counts between both procedures was not statistical significant (p = 0.108), but there were significantly less culture-positive implants after the decontamination procedure in the phosphoric acid group (p = 0.042). At 3 months post-surgery, 75% of the implants in the control group and 63.3% of the implants in the test group showed disease resolution. However, no significant differences in clinical and microbiological outcomes between both groups were found.

Conclusions

The application of 35% phosphoric acid after mechanical debridement is superior to mechanical debridement combined with sterile saline rinsing for decontamination of the implant surface during surgical peri-implantitis treatment. However, phosphoric acid as implant surface decontaminant does not seem to enhance clinical outcomes on a 3-month follow-up.

Trial registration

Netherlands National Trial Register, NTR5185 (www.trialregister.nl)

Novel bioactive tetracycline-containing electrospun polymer fibers as a potential antibacterial dental implant coating

The purpose of this investigation was to determine the ability of tetracycline-containing fibers to inhibit biofilm formation of peri-implantitis-associated pathogens [i.e., Porphyromonas gingivalis (Pg), Fusobacterium nucleatum (Fn), Prevotella intermedia (Pi), and Aggregatibacter actinomycetemcomitans (Aa)]. Tetracycline hydrochloride (TCH) was added to a poly(DL-lactide) [PLA], poly(ε-caprolactone) [PCL], and gelatin [GEL] polymer blend solution at distinct concentrations to obtain the following fibers: PLA:PCL/GEL (TCH-free, control), PLA:PCL/GEL + 5 % TCH, PLA:PCL/GEL + 10 % TCH, and PLA:PCL/GEL + 25 % TCH. The inhibitory effect of TCH-containing fibers on biofilm formation was assessed by colony-forming units (CFU/mL). Qualitative analysis of biofilm inhibition was done via scanning electron microscopy (SEM). Statistical significance was reported at p < 0.05. Complete inhibition of biofilm formation on the fibers was observed in groups containing TCH at 10 and 25 wt%. Fibers containing TCH at 5 wt% demonstrated complete inhibition of Aa biofilm. Even though a marked reduction in CFU/mL was observed with an increase in TCH concentration, Pi proved to be the most resilient microorganism. SEM images revealed the absence of or a notable decrease in bacterial biofilm on the TCH-containing nanofibers. Collectively, our data suggest that tetracycline-containing fibers hold great potential as an antibacterial dental implant coating.