Effect of titanium surface functionalization with bioactive glass on osseointegration: An experimental study in dogs

Photothermal Antibacterial Effect of Gold Nanostars Coating on Titanium Implant and Its Osteogenic Performance

Introduction

Titanium implants are widely used in dentistry due to their mechanical strength and biocompatibility, yet their biological inertness and lack of antimicrobial properties contribute to high failure rates from poor osseointegration and infections like peri-implantitis. To address these limitations, this study developed a gold nanostar (GNS)-coated titanium implant (Ti-GNS) and systematically evaluated its osteogenic and photothermal antibacterial functions. The research aimed to enhance osseointegration through surface modification while leveraging GNS's photothermal effect for on-demand antibacterial activity, offering a dual-functional strategy to improve implant performance.

Methods

GNSs were synthesized and anchored onto titanium surfaces through surface modification via silanization. Material characterization included morphological, elemental, and photothermal analyses. In vitro experiments assessed osteogenic differentiation of bone marrow stem cells (ALP activity, mineralization, gene/protein expression) and antibacterial efficacy against Staphylococcus aureus and Escherichia coli under NIR. In vivo performance was evaluated by implanting Ti, Ti-Si (silanized), and Ti-GNS in rat femurs, followed by micro-CT and histological analysis.

Results

Silanization and GNS deposition optimized titanium surfaces by significantly enhancing wettability and nanoscale roughness, while photothermal activation under NIR irradiation demonstrated temperature-dependent responsiveness. Furthermore, in vivo evaluations confirmed Ti-GNS biocompatibility and revealed enhanced osteogenic potential through promoted cell adhesion, proliferation, as well as osteoinductive marker expression. Notably, the Ti-GNS group exhibited superior osseointegration alongside stable antimicrobial efficacy post-NIR exposure.

Conclusion

GNS-coated titanium implants synergistically enhance osteogenesis and provide NIR-responsive antibacterial activity. The modified surface improved cell interactions and bone formation while achieving near-complete bacterial elimination under light activation. This dual-functional strategy addresses key challenges in implantology, though long-term stability and clinical translation require further investigation. The study establishes a foundation for photothermal antimicrobial implants with significant potential in dental applications.

Modulation of osteoclastogenesis by macrogeometrically designed hydrophilic dual acid-etched titanium surfaces

The aim of this study was to evaluate the influence of implant macrodesign and surface hydrophilicity on osteoclast (OC) differentiation, activation, and survival in vitro. Titanium disks were produced with a sandblasted, dual acid-etched surface, with or without additional chemical modification for increasing hydrophilicity (SAE-HD and SAE, respectively) and different macrodesign comprising trapezoidal (HLX) or triangular threads (TMX). This study evaluated 7 groups in total, 4 of which were experimental: HLX/SAE-HD, HLX-SAE, TMX/SAE-HD, and TMX/SAE; and 3 control groups comprising OC differentiated on polystyrene plates (CCPC): a positive CCPC (+), a negative CCPC (-), and a lipopolysaccharide-stimulated assay positive control group, CCPC-LPS. Murine macrophage RAW264.7 cells were seeded on the disks, differentiated to OC (RAW-OC) by receptor activator of nuclear factor-κB ligand (RANKL) treatment and cultured for 5 days. Osteoclast differentiation and cell viability were respectively assessed by specific enzymatic Tartrate-Resistant Acid Phosphatase (TRAP) activity and MTT assays. Expression levels of various OC-related genes were measured at the mRNA level by quantitative polymerase chain reaction (qPCR). HLX/SAE-HD, TMX/SAE-HD, and HLX/SAE significantly suppressed OC differentiation when compared to CCPC (+). Cell viability was significantly increased in TMX/SAE and reduced in HLX/SAE-HD. In addition, the expression of Interleukin (IL)-6 and Tumour Necrosis Factor (TNF)-α was upregulated in TMX/SAE-HD compared to CCPC (+). Hydrophilic surfaces negatively modulate macrophage/osteoclast viability. Specifically, SAE-HD with double triangular threads increases the cellular pro-inflammatory status, while surface hydrophilicity and macrodesign do not seem to have a distinct impact on osteoclast differentiation, activation, or survival.

Modification of titanium orthopedic implants with bioactive glass: a systematic review of in vivo and in vitro studies

Bioactive glasses (BGs) are ideal biomaterials in the field of bio-restoration due to their excellent biocompatibility. Titanium alloys are widely used as a bone graft substitute material because of their excellent corrosion resistance and mechanical properties; however, their biological inertness makes them prone to clinical failure. Surface modification of titanium alloys with bioactive glass can effectively combine the superior mechanical properties of the substrate with the biological properties of the coating material. In this review, the relevant articles published from 2013 to the present were searched in four databases, namely, Web of Science, PubMed, Embase, and Scopus, and after screening, 49 studies were included. We systematically reviewed the basic information and the study types of the included studies, which comprise in vitro experiments, animal tests, and clinical trials. In addition, we summarized the applied coating technologies, which include pulsed laser deposition (PLD), electrophoretic deposition, dip coating, and magnetron sputtering deposition. The superior biocompatibility of the materials in terms of cytotoxicity, cell activity, hemocompatibility, anti-inflammatory properties, bioactivity, and their good bioactivity in terms of osseointegration, osteogenesis, angiogenesis, and soft tissue adhesion are discussed. We also analyzed the advantages of the existing materials and the prospects for further research. Even though the current research status is not extensive enough, it is still believed that BG-coated Ti implants have great clinical application prospects.

Mechano-Biological Computer Model of Scaffold-Supported Bone Regeneration: Effect of Bone Graft and Scaffold Structure on Large Bone Defect Tissue Patterning

Large segmental bone defects represent a clinical challenge for which current treatment procedures have many drawbacks. 3D-printed scaffolds may help to support healing, but their design process relies mainly on trial and error due to a lack of understanding of which scaffold features support bone regeneration. The aim of this study was to investigate whether existing mechano-biological rules of bone regeneration can also explain scaffold-supported bone defect healing. In addition, we examined the distinct roles of bone grafting and scaffold structure on the regeneration process. To that end, scaffold-surface guided migration and tissue deposition as well as bone graft stimulatory effects were included in an in silico model and predictions were compared to in vivo data. We found graft osteoconductive properties and scaffold-surface guided extracellular matrix deposition to be essential features driving bone defect filling in a 3D-printed honeycomb titanium structure. This knowledge paves the way for the design of more effective 3D scaffold structures and their pre-clinical optimization, prior to their application in scaffold-based bone defect regeneration.

Biofilm Formation and Expression of Virulence Genes of Microorganisms Grown in Contact with a New Bioactive Glass

Bioactive glass F18 (BGF18), a glass containing SiO2-Na2O-K2O-MgO-CaO-P2O5, is highly effective as an osseointegration buster agent when applied as a coating in titanium implants. Biocompatibility tests using this biomaterial exhibited positive results; however, its antimicrobial activity is still under investigation. In this study we evaluated biofilm formation and expression of virulence-factor-related genes in Candida albicans, Staphylococcus epidermidis, and Pseudomonas aeruginosa grown on surfaces of titanium and titanium coated with BGF18. C. albicans, S. epidermidis, and P. aeruginosa biofilms were grown on specimens for 8, 24, and 48 h. After each interval, the pH was measured and the colony-forming units were counted for the biofilm recovery rates. In parallel, quantitative real-time polymerase chain reactions were carried out to verify the expression of virulence-factor-related genes. Our results showed that pH changes of the culture in contact with the bioactive glass were merely observed. Reduction in biofilm formation was not observed at any of the studied time. However, changes in the expression level of genes related to virulence factors were observed after 8 and 48 h of culture in BGF18. BGF18 coating did not have a clear inhibitory effect on biofilm growth but promoted the modulation of virulence factors.

Application of Shark Teeth-Derived Bioapatites as a Bone Substitute in Veterinary Orthopedics. Preliminary Clinical Trial in Dogs and Cats

Background: The autograft is still considered the gold standard for the treatment of bone defects. However, given the significant morbidity of the donor site with which it has been associated, alternative substitutes for bone grafts have been developed. In the present study, a bone substitute composed of CaP biphasic bioceramics obtained from shark teeth was used (BIOFAST-VET). Objective: The objective of this study is to evaluate the efficacy of a marine bioapatite in the veterinary clinical field using it as a bone-grafting scaffold in dogs and cats. Methods: The biomaterial was randomly distributed in 6 veterinary clinical centers in Spain and was used in 24 cases (20 dogs and 4 cats) including 14 fractures, 9 arthrodesis, and 1 bone cyst. Grains between 500 and 2,000 μm were used. Inclusion and exclusion criteria were established. The time of consolidation and functional recovery were quantitatively and qualitatively assessed. For this, a follow-up was carried out at 2, 4, 8, and 12 weeks, included radiographic images, physical examination and sharing the feedback with the owners. Results: Nineteen cases completed the study (18 dogs and 1 cat; 11 fractures, 7 arthrodesis, and 1 bone cyst). The remaining five were excluded because they did not complete the radiographic follow-up (three cats and two dogs), being three arthrodesis and two fractures. In 18 of 19 cases, the use of the biomaterial was successful; the remaining one failed due to causes not related to the biomaterial. There were no systemic or local adverse reactions. Eighteen patients had a good functional recovery. The average consolidation time was 5.94 weeks in dogs with fractures and arthrodesis, not finding statistically significant differences between sex, weight, and procedure. Conclusions: This biomaterial is presented as a very suitable candidate for orthopedic surgery in the veterinary field. Preliminary results showed that its use reduces consolidation time in dogs with fractures and arthrodesis. In addition, no adverse systemic or local reactions have been observed derived from its use.

Bactericidal activity and biofilm inhibition of F18 bioactive glass against Staphylococcus aureus

Antimicrobial treatment failure has been increasing at alarming rates. In this context, the bactericidal properties of biocompatible antimicrobial agents have been widely studied. F18 is a recently developed bioactive glass that presents a much wider working range when compared to other bioactive glasses, a feature that allows it to be used for coating metallic implants, sintering scaffolds or manufacturing fibers for wound healing applications. The aim of this study was to investigate the in vitro bactericidal and anti-biofilm activity of F18 glass as a powder and as a coating on steel samples, and to explore the effects of its dissolution products at concentrations from 3 mg/mL to 50 mg/mL against the Staphylococcus aureus and methicillin-resistant Staphylococcus aureus (MRSA) biofilms. Furthermore, we intend to verify whether changes in the medium pH could influence the bactericidal activity of F18. The results indicated that F18 presented bactericidal activity in preformed S. aureus and MRSA biofilms, reducing more than 6 logs of the viable cells that remained in contact with 50 mg/mL for 24 h. Moreover, an anti-biofilm activity was observed after 12 h of direct contact, with a drop of more than 6 logs of the viable bacterial population. Neutralization of the F18 solution pH decreased its bactericidal efficacy. These results indicate that the F18 glass could be considered as an alternative material for controlling and treating infections by S. aureus.

Biomaterials for orthopedics: anti-biofilm activity of a new bioactive glass coating on titanium implants

This study evaluated adhesion and biofilm formation by Candida albicans, Pseudomonas aeruginosa and Staphylococcus epidermidis on surfaces of titanium (Ti) and titanium coated with F18 Bioactive Glass (BGF18). Biofilms were grown and the areas coated with biofilm were determined after 2, 4 and 8 h. Microscopy techniques were applied in order to visualize the structure of the mature biofilm and the extracellular matrix. On the BGF18 specimens, there was less biofilm formation by C. albicans and S. epidermidis after incubation for 8 h. For P. aeruginosa biofilm, a reduction was observed after incubation for 4 h, and it remained reduced after 8 h on BGF18 specimens. All biofilm matrices seemed to be thicker on BGF18 surface than on titanium surfaces. BGF18 showed significant anti-biofilm activity in comparison with Ti in the initial periods of biofilm formation; however, there was extensive biofilm after incubation for 48 h.

Visible-Light-Induced Photocatalytic and Antibacterial Activity of TiO2 Codoped with Nitrogen and Bismuth: New Perspectives to Control Implant-Biofilm-Related Diseases

Biofilm-associated diseases are one of the main causes of implant failure. Currently, the development of implant surface treatment goes beyond the osseointegration process and focuses on the creation of surfaces with antimicrobial action and with the possibility to be re-activated (i.e., light source activation). Titanium dioxide (TiO₂), an excellent photocatalyst used for photocatalytic antibacterial applications, could be a great alternative, but its efficiency is limited to the ultraviolet (UV) range of the electromagnetic spectrum. Since UV radiation has carcinogenic potential, we created a functional TiO₂ coating codoped with nitrogen and bismuth via the plasma electrolytic oxidation (PEO) of titanium to achieve an antibacterial effect under visible light with re-activation potential. A complex surface topography was demonstrated by scanning electron microscopy and three-dimensional confocal laser scanning microscopy. Additionally, PEO-treated surfaces showed greater hydrophilicity and albumin adsorption compared to control, untreated titanium. Bismuth incorporation shifted the band gap of TiO₂ to the visible region and facilitated higher degradation of methyl orange (MO) in the dark, with a greater reduction in the concentration of MO after visible-light irradiation even after 72 h of aging. These results were consistent with the in vitro antibacterial effect, where samples with nitrogen and bismuth in their composition showed the greatest bacterial reduction after 24 h of dual-species biofilm formation ( Streptococcus sanguinis and Actinomyces naeslundii) in darkness with a superior effect at 30 min of visible-light irradiation. In addition, such a coating presents reusable photocatalytic potential and good biocompatibility by presenting a noncytotoxicity effect on human gingival fibroblast cells. Therefore, nitrogen and bismuth incorporation into TiO₂ via PEO can be considered a promising alternative for dental implant application with antibacterial properties in darkness, with a stronger effect after visible-light application.