Electrochemical checking of aerobic isolates from electrochemically active biofilms formed in compost

The study of the performance of a microbial fuel cell: a progress towards the improvement of low electrical bioenergy output by using an amplification system

OBJECTIVE

A microbial fuel cell (MFC) has been conceived and constructed for the treatment of the sheep manure wastes and their conversion into clean sustainable renewable energy. The aim of the present investigation was to examine the performance of this bioelectrochemical device, in breaking down the organic matter (pollutant removal) and simultaneously producing electricity. Furthermore, the objective was to enhance the low electric energy by using an adequate amplification system.

RESULTS

So, the chemical oxygen demand (COD) removal was increased by 58.7% with the MFC running for 10 days. However, this technology faces practical barriers as it produces low electrical energy. A power management system was therefore elaborated in this respect. It included the MFC, operational amplifier (OA), solar photovoltaic panel and a boost DC/DC converter. The low voltage output obtained was thus increased substantially using the OA prior to its polarization by the solar photovoltaic module. The amplified voltage was sufficiently enough and in consequence, utilized to feed a light emitting diode. The low output voltage 0.5 V was simply harvested, successfully boosted up to approximately 2 V (i.e. 4 times higher) and finally harnessed as a power supply.

CONCLUSIONS

The MFCs association shows the positive stacking effect successfully, when the cells were connected in parallel. This novel application is very interesting to utilize the natural bioenergy contained in wastes to supply small electronic devices.

Bioelectricity generation using long-term operated biocathode: RFLP based microbial diversity analysis

In the present work, power generation and substrate removal efficiencies of long-term operated microbial fuel cells, containing abiotic cathodes and biocathodes, were evaluated for 220 days. Among the two microbial fuel cell (MFC) types, the one containing biocathode showed higher power density (54 mW/m2), current density (122 mA/m2) coulombic efficiency (33%), and substrate removal efficiency (94%) than the abiotic cathode containing MFC. Voltammetric analysis also witnessed higher and sustainable electron discharge for the MFC with biocathode, when compared with the abiotic cathode MFC. Over the tested period, both MFC have shown a cell voltage drop, after 150 and 165, days, for the MFC with biocathode and abiotic cathodes, respectively. Polymerase chain reaction (PCR) based restriction fragment length polymorphism (RFLP) analysis identified 281 clones. Bacteria belonging to Acinetobacter, Acidovorax, Pseudomonas and Burkholderia were observed in the abiotic cathode MFC. Bacteria belonging to Geobacter, Cupriavidus and Acidobacteria were observed in the biocathode MFC. Almost similar types of archaea (Methanosarcinales, Methanolinea, Nitrososphaera and Methanomicrobiales) were observed in both MFCs.

Waste valorization using solid-phase microbial fuel cells (SMFCs): Recent trends and status

This review article discusses the use of solid waste processed in solid-phase microbial fuel cells (SMFCs) as a source of electrical energy. Microbial Fuel Cells (MFCs) are typically operated in the liquid phase because the ion transfer process is efficient in liquid media. Nevertheless, some researchers have considered the potential for MFCs in solid phases (particularly for treating solid waste). This has promise if several important factors are optimized, such as the type and amount of substrate, microorganism community, system configuration, and type and number of electrodes, which increases the amount of electricity generated. The critical factor that affects the SMFC performance is the efficiency of electron and proton transfer through solid media. However, this limitation may be overcome by electrode system enhancements and regular substrate mixing. The integration of SMFCs with other conventional solid waste treatments could be used to produce sustainable green energy. Although SMFCs produce relatively small amounts of energy compared with other waste-to-energy treatments, SMFCs are still promising to achieve zero-emission treatment. Therefore, this article addresses the challenges and fills the gaps in SMFC research and development.

Response of microbial community structure to pre-acclimation strategies in microbial fuel cells for domestic wastewater treatment

Microbial community structures and performance of air-cathode microbial fuel cells (MFCs) inoculated with activated sludge from domestic wastewater were investigated to evaluate the effects of three substrate pre-acclimation strategies: 1, serial pre-acclimation with acetate and glucose before supplying domestic wastewater; 2, one step pre-acclimation with acetate before supplying domestic wastewater; and 3, direct supply of domestic wastewater without any pre-acclimation. Strategy 1 showed much higher current generation (1.4mA) and Coulombic efficiency (33.5%) than strategies 2 (0.7mA and 9.4%) and 3 (0.9mA and 10.3%). Pyrosequencing showed that microbial communities were significantly affected by pre-acclimation strategy. Although Proteobacteria was the dominant phylum with all strategies, Actinobacteria was abundant when MFCs were pre-acclimated with glucose after acetate. Not only anode-respiring bacteria (ARB) in the genus Geobacter but also non-ARB belonging to the family Anaerolinaceae seemed to play important roles in air-cathode MFCs to produce electricity from domestic wastewater.

Protons accumulation during anodic phase turned to advantage for oxygen reduction during cathodic phase in reversible bioelectrodes

Reversible bioelectrodes were designed by alternating acetate and oxygen supply. It was demonstrated that the protons produced and accumulated inside the biofilm during the anodic phase greatly favored the oxygen reduction reaction when the electrode was switched to become the biocathode. Protons accumulation, which hindered the bioanode operation, thus became an advantage for the biocathode. The bioanodes, formed from garden compost leachate under constant polarization at -0.2 V vs. SCE, were able to support long exposure to forced aeration, with only a slight alteration of their anodic efficiency. They produced a current density of 16±1.7 A/m2 for acetate oxidation and up to -0.4 A/m2 for oxygen reduction. Analysis of the microbial communities by 16S rRNA pyrosequencing revealed strong selection of Chloroflexi (49±1%), which was not observed for conventional bioanodes not exposed to oxygen. Chloroflexi were found as the dominant phylum of electroactive biofilms for the first time.

Accelerated reduction of chlorinated nitroaromatic antibiotic chloramphenicol by biocathode

Chlorinated nitroaromatic antibiotic chloramphenicol (CAP) is a priority pollutant in wastewaters. A fed-batch bioelectrochemical system (BES) with biocathode with applied voltage of 0.5 V (served as extracellular electron donor) and glucose as intracellular electron donor was applied to reduce CAP to amine product (AMCl2). The biocathode BES converted 87.1 ± 4.2% of 32 mg/L CAP in 4 h, and the removal efficiency reached 96.0 ± 0.9% within 24 h. Conversely, the removal efficiency of CAP in BES with an abiotic cathode was only 73.0 ± 3.2% after 24 h. When the biocathode was disconnected (no electrochemical reaction but in the presence of microbial activities), the CAP removal rate was dropped to 62.0% of that with biocathode BES. Acetylation of one hydroxyl of CAP was noted exclusive in the biocatalyzed process, while toxic intermediates, hydroxylamino (HOAM), and nitroso (NO), from CAP reduction were observed only in the abiotic cathode BES. Electrochemical hydrodechlorination and dehalogenase were responsible for dechlorination of AMCl2 to AMCl in abiotic and microbial cathode BES, respectively. The cyclic voltammetry (CV) highlighted higher peak currents and lower overpotentials for CAP reduction at the biocathode compared with abiotic cathode. With the biocathode BES, antibacterial activity of CAP was completely removed and nitro group reduction combined with dechlorination reaction enhanced detoxication efficiency of CAP. The CAP cathodic transformation pathway was proposed based on intermediates analysis. Bacterial community analysis indicated that the dominate bacteria on the biocathode were belonging to α, β, and γ-Proteobacteria. The biocathode BES could serve as a potential treatment process for CAP-containing wastewater.

Garden compost inoculum leads to microbial bioanodes with potential-independent characteristics

Garden compost leachate was used to form microbial bioanodes under polarization at -0.4, -0.2 and +0.1 V/SCE. Current densities were 6.3 and 8.9 A m(-2) on average at -0.4 and +0.1 V/SCE respectively, with acetate 10 mM. The catalytic cyclic voltammetry (CV) showed similar electrochemical characteristics for all bioanodes and indicated that the lower currents recorded at -0.4V/SCE were due to the slower interfacial electron transfer rate at this potential, consistently with conventional electrochemical kinetics. RNA- and DNA-based DGGE evidenced that the three dominant bacterial groups Geobacter, Anaerophaga and Pelobacter were identical for all bioanodes and did not depend on the polarization potential. Only non-turnover CVs showed differences in the redox equipment of the biofilms, the highest potential promoting multiple electron transfer pathways. This first description of a potential-independent electroactive microbial community opens up promising prospects for the design of stable bioanodes for microbial fuel cells.

Microbial catalysis of the oxygen reduction reaction for microbial fuel cells: a review

The slow kinetics of the electrochemical oxygen reduction reaction (ORR) is a crucial bottleneck in the development of microbial fuel cells (MFCs). This article firstly gives an overview of the particular constraints imposed on ORR by MFC operating conditions: neutral pH, slow oxygen mass transfer, sensitivity to reactive oxygen species, fouling and biofouling. A review of the literature is then proposed to assess how microbial catalysis could afford suitable solutions. Actually, microbial catalysis of ORR occurs spontaneously on the surface of metallic materials and is an effective motor of microbial corrosion. In this framework, several mechanisms have been proposed, which are reviewed in the second part of the article. The last part describes the efforts made in the domain of MFCs to determine the microbial ecology of electroactive biofilms and define efficient protocols for the formation of microbial oxygen-reducing cathodes. Although no clear mechanism has been established yet, several promising solutions have been recently proposed.

Harvesting electricity with Geobacter bremensis isolated from compost

Electrochemically active (EA) biofilms were formed on metallic dimensionally stable anode-type electrode (DSA), embedded in garden compost and polarized at +0.50 V/SCE. Analysis of 16S rRNA gene libraries revealed that biofilms were heavily enriched in Deltaproteobacteria in comparison to control biofilms formed on non-polarized electrodes, which were preferentially composed of Gammaproteobacteria and Firmicutes. Among Deltaproteobacteria, sequences affiliated with Pelobacter and Geobacter genera were identified. A bacterial consortium was cultivated, in which 25 isolates were identified as Geobacter bremensis. Pure cultures of 4 different G. bremensis isolates gave higher current densities (1400 mA/m² on DSA, 2490 mA/m² on graphite) than the original multi-species biofilms (in average 300 mA/m² on DSA) and the G. bremensis DSM type strain (100–300 A/m² on DSA; 2485 mA/m² on graphite). FISH analysis confirmed that G. bremensis represented a minor fraction in the original EA biofilm, in which species related to Pelobacter genus were predominant. The Pelobacter type strain did not show EA capacity, which can explain the lower performance of the multi-species biofilms. These results stressed the great interest of extracting and culturing pure EA strains from wild EA biofilms to improve the current density provided by microbial anodes.

Electroactivity of phototrophic river biofilms and constitutive cultivable bacteria

Electroactivity is a property of microorganisms assembled in biofilms that has been highlighted in a variety of environments. This characteristic was assessed for phototrophic river biofilms at the community scale and at the bacterial population scale. At the community scale, electroactivity was evaluated on stainless steel and copper alloy coupons used both as biofilm colonization supports and as working electrodes. At the population scale, the ability of environmental bacterial strains to catalyze oxygen reduction was assessed by cyclic voltammetry. Our data demonstrate that phototrophic river biofilm development on the electrodes, measured by dry mass and chlorophyll a content, resulted in significant increases of the recorded potentials, with potentials of up to +120 mV/saturated calomel electrode (SCE) on stainless steel electrodes and +60 mV/SCE on copper electrodes. Thirty-two bacterial strains isolated from natural phototrophic river biofilms were tested by cyclic voltammetry. Twenty-five were able to catalyze oxygen reduction, with shifts of potential ranging from 0.06 to 0.23 V, cathodic peak potentials ranging from -0.36 to -0.76 V/SCE, and peak amplitudes ranging from -9.5 to -19.4 μA. These isolates were diversified phylogenetically (Actinobacteria, Firmicutes, Bacteroidetes, and Alpha-, Beta-, and Gammaproteobacteria) and exhibited various phenotypic properties (Gram stain, oxidase, and catalase characteristics). These data suggest that phototrophic river biofilm communities and/or most of their constitutive bacterial populations present the ability to promote electronic exchange with a metallic electrode, supporting the following possibilities: (i) development of electrochemistry-based sensors allowing in situ phototrophic river biofilm detection and (ii) production of microbial fuel cell inocula under oligotrophic conditions.

Powering microbes with electricity: direct electron transfer from electrodes to microbes

The discovery of electrotrophs, microorganisms that can directly accept electrons from electrodes for the reduction of terminal electron acceptors, has spurred the investigation of a wide range of potential applications. To date, only a handful of pure cultures have been shown to be capable of electrotrophy, but this process has also been inferred in many studies with undefined consortia. Potential electron acceptors include: carbon dioxide, nitrate, metals, chlorinated compounds, organic acids, protons and oxygen. Direct electron transfer from electrodes to cells has many advantages over indirect electrical stimulation of microbial metabolism via electron shuttles or hydrogen production. Supplying electrons with electrodes for the bioremediation of chlorinated compounds, nitrate or toxic metals may be preferable to adding organic electron donors or hydrogen to the subsurface or bioreactors. The most transformative application of electrotrophy may be microbial electrosynthesis in which carbon dioxide and water are converted to multi-carbon organic compounds that are released extracellularly. Coupling photovoltaic technology with microbial electrosynthesis represents a novel photosynthesis strategy that avoids many of the drawbacks of biomass-based strategies for the production of transportation fuels and other organic chemicals. The mechanisms for direct electron transfer from electrodes to microorganisms warrant further investigation in order to optimize envisioned applications.

Catalysis of the electrochemical reduction of oxygen by bacteria isolated from electro-active biofilms formed in seawater

Biofilms formed in aerobic seawater on stainless steel are known to be efficient catalysts of the electrochemical reduction of oxygen. Based on their genomic analysis, seven bacterial isolates were selected and a cyclic voltammetry (CV) procedure was implemented to check their electrocatalytic activity towards oxygen reduction. All isolates exhibited close catalytic characteristics. Comparison between CVs recorded with glassy carbon and pyrolytic graphite electrodes showed that the catalytic effect was not correlated with the surface area covered by the cells. The low catalytic effect obtained with filtered isolates indicated the involvement of released redox compounds, which was confirmed by CVs performed with adsorbed iron-porphyrin. None of the isolates were able to form electro-active biofilms under constant polarization. The capacity to catalyze oxygen reduction is shown to be a widespread property among bacteria, but the property detected by CV does not necessarily confer the ability to achieve stable oxygen reduction under constant polarization.