In vivo properties of uterine suspensory tissue in pelvic organ prolapse

A novel anchoring system for pelvic organ prolapse repair: an observational study

INTRODUCTION AND HYPOTHESIS

Sacrospinous ligament (SSL) fixation is an effective and widely used vaginal procedure for correcting apical prolapse. The Saffron Fixation System (Coloplast Corp., Minneapolis, MN, USA) is a new anchoring device aimed at facilitating a durable, easy, and short procedure for SSL fixation with the goal of minimizing operative complications. The objective was to demonstrate the efficacy and safety of anchor deployment and suture fixation for pelvic organ prolapse repair using the Saffron Fixation System.

METHODS

An observational human cadaver study was conducted to measure the distance between anchor location and anatomical landmarks in the pelvis, and the holding force of the fixated anchors. Anchors were placed in four human cadavers by different implanters. The pull-out force of these anchors was measured to assess efficacy (three cadavers by three implanters) and the distance between anchors and primal vessels and nerves was measured to assess safety (one cadaver by one implanter).

RESULTS

Nineteen out of 20 anchors (95%) were correctly placed as judged by independent assessment performed by non-implanting surgeons. Distance between anchors and surrounding nerves and vessels exceeded 10 mm. Mean (SD) pull out-force was 17.9 (5.6) N.

CONCLUSION

The innovative anchoring device that was developed appeared to enable precise and solid anchor placement in the SSL. Future clinical studies are needed to explore if the theoretical advantages of this device translate to improved clinical outcomes in comparison with available suturing and anchoring devices.

Two-dimensional biomechanical finite element modeling of the pelvic floor and prolapse

We developed the pelvic floor model in physiological and pathological states to understand the changes of biomechanical axis and support that may occur from the normal physiological state to the prolapse pathological state of the pelvic floor. Based on the physiological state model of the pelvic floor, we model the uterus to the pathological state position by balancing intra-abdominal pressure (IAP) and uterine pathological position load. Under combined impairments, we compared the patterns of changes in pelvic floor biomechanics that may be induced by different uterine morphological characteristic positions under different IAP. The orientation of the uterine orifice gradually changes from the sacrococcygeal direction to the vertical downward of vaginal orifice, and a large downward prolapse displacement occurs, and the posterior vaginal wall shows "kneeling" profile with posterior wall bulging prolapse. When the abdominal pressure value was 148.1 cmH₂O, the descent displacement of the cervix in the normal and pathological pelvic floor system was 11.94, 20, 21.83 and 19.06 mm in the healthy state, and 13.63, 21.67, 22.94 and 19.38 mm in the combined impairment, respectively. The above suggests a maximum cervical descent displacement of the uterus in the anomalous 90° position, with possible cervical-uterine prolapse as well as prolapse of the posterior vaginal wall. The combined forces of the pelvic floor point in the direction of vertical downward prolapse of the vaginal orifice, and the biomechanical support of the bladder and sacrococcygeal bone gradually diminishes, which may exacerbate the soft tissue impairments and biomechanical imbalances of the pelvic floor to occur of POP disease.

Quantification of senescence-associated secretory phenotype proteins in the vaginal secretions of pre- and postmenopausal women with and without prolapse

Objectives

Cellular senescence has been proposed as a pathophysiologic driver in the development of pelvic organ prolapse (POP), especially during aging. In this study, we aimed to determine if markers of cell senescence can be quantified from vaginal secretions collected from pre- and postmenopausal women with and without POP.

Methods

Vaginal swabs were collected from 81 women in four groups: premenopausal with (pre-P) and without prolapse (pre-NP), and postmenopausal with (post-P) and without prolapse (post-NP). Multiplex immunoassays (MagPix) were then used to detect and quantify the presence of 10 SASP proteins in vaginal secretions.

Results

The total protein concentration of vaginal secretions differed significantly among the four groups (P = 0.003) with highest mean concentrations in pre-P [16, interquartile range (IQR) = 4.6, 38.3 μg/μL] and lowest mean concentrations in post-P (4.4, IQR = 2.6, 7 μg/μL). The normalized concentrations of several SASP markers differed significantly among groups, with the highest concentrations being seen in the post-P group, and the lowest concentrations being in the pre-NP group. Using these key markers, we then constructed receiver-operator curves to determine the relative sensitivity and specificity of these markers in predicting prolapse.

Conclusions

In this study, we found that SASP proteins can be detected and quantified in vaginal secretions. Several of these markers were differentially expressed among the four groups studied, with the highest normalized concentrations of SASP markers found among postmenopausal women with prolapse. Overall, the data support the theory that senescence is associated with prolapse during aging but that other factors may be important in younger women who develop POP before menopause.

Ex Vivo Uniaxial Tensile Properties of Rat Uterosacral Ligaments

This manuscript presents new experimental methods for testing the ex vivo tensile properties of the uterosacral ligaments (USLs) in rats. The USL specimens ([Formula: see text]) were carefully dissected to preserve their anatomical attachments, and they were loaded along their main in vivo loading direction (MD) using a custom-built uniaxial tensile testing device. During loading, strain maps in both the MD and the perpendicular direction (PD) were collected using the digital image correlation technique. The mean (± S.E.M.) maximum load and displacement at the maximum load were [Formula: see text] N and [Formula: see text] mm, respectively. The USLs were found to be highly heterogeneous structures, with some specimens experiencing strains in the MD that were lower than [Formula: see text] and others reaching strains that were up to [Formula: see text] in the intermediate region. At 0.5 kPa stress, a value reached by all the specimens, the mean strain in the MD was [Formula: see text] while at 5 kPa stress, a value achieved only by 9 out of the 21 specimens, the mean strain increased to [Formula: see text]. Under uniaxial loading, the specimens also elongated in the PD, with strains that were one order of magnitude lower than the strains in the MD; at the 0.5 kPa stress, the mean strain in the PD was recorded to be [Formula: see text] and, at the 5 kPa stress, the strain in the PD was [Formula: see text]. The directions of maximum principal strains remained almost unchanged with the increase in stress, indicating that little microstructural re-organization occurred due to uniaxial loading. This study serves as a springboard for future investigations on the supportive function of the USLs in the rat model by offering guidelines on testing methods that capture their complex mechanical behavior.

A 2D equivalent mechanical model of the whole pelvic floor and impairment simulation

We developed a complete 2D equivalent mechanical model of the pelvic floor based on magnetic resonance imaging (MRI) images of a 35-year-old healthy woman. This model can simulate anterior vaginal prolapse (AVP) due to soft tissue impairment. Thus, we can study the mechanism of prolapse formation from a mechanical perspective and improve the assessment and treatment of the condition in clinical practice. Based on 2D MRI image parameter measurements and computer-aided design methods, the 2D equivalent mechanical model of the whole pelvic floor in the sagittal plane was accurately reconstructed, which includes all necessary tissues of the pelvic floor system. Material parameters were mainly from the literature. We simulated the impairment by reducing the tissue's mechanical properties, and numerical simulations predicted the mechanical response and morphological changes of the healthy and impaired pelvic floor in different states. In six intra-abdominal pressure (IAP) states (8.4-208.9 cmH₂ O), the maximum cervical descent in the impaired pelvic floor was 0.3-18.521 mm, which was much greater than that in the healthy pelvic floor (0.14-6.55 mm). Once the impairment occurred (0%-25%), there was a significant increase in maximum displacement, stress, and cervical descent (30.9-36.5 mm, 0.56-1.12 MPa, 4.6-12.1 mm), and a clinically similar prolapse shape occurred. Simple supine and standing will not cause prolapse. The formation of prolapse is closely related to vaginal tissue impairment. In the standing position, the main forces on the healthy pelvic floor system are distributed horizontally posteriorly and inferiorly, reducing the burden in the vertically downward direction.

Comparison of in vivo visco-hyperelastic properties of uterine suspensory tissue in women with and without pelvic organ prolapse

The uterine suspensory tissue (UST) complex includes the cardinal (CL) and uterosacral "ligaments" (USL), which are mesentery-like structures that play a role in resisting pelvic organ prolapse (POP). Since there is no information on the time-dependent material properties of the whole structure in situ and in vivo, we developed and tested an intraoperative technique to quantify in vivo whether there is a significant difference in visco-hyperelastic behavior of the CL and USL between women with and without POP. Thirteen women with POP (cases) and four controls scheduled for surgery were selected from an ongoing POP study. Immediately prior to surgery, a computer-controlled linear servo-actuator with a series force transducer applied a continuous, caudally directed traction force while simultaneously recording the resulting cervical displacement in the same direction. After applying an initial 1.1 N preload, a ramp rate of 4 mm/s was used to apply a maximum force of 17.8 N in three "ramp-and-hold" test trials. A simplified bilateral four-cable biomechanical model was used to identify the material behavior of each ligament. For this, the initial cross-section areas of the CL and USL were measured on 3-T magnetic resonance image-based 3D models from each subject. The time-dependent strain energy function of CL/USL was defined with a three-parameter hyperelastic Mooney-Rivlin material model and a two-term Prony series in relaxation form. When cases were compared with controls, the estimated time-dependent material constants of CL and USL did not differ significantly. These are the first measurements that compare the in vivo and in situ visco-hyperelastic response of the tissues comprising the CL and USL to loading in women with and without prolapse. Larger sample sizes would help improve the precision of intergroup differences.

In-plane and out-of-plane deformations of gilt utero-sacral ligaments

The uterosacral ligaments (USLs) are supportive structures of the uterus and apical vagina. The mechanical function of these ligaments within the pelvic floor is crucial not only in normal physiological conditions but also in reconstructive surgeries for pelvic organ prolapse. Discrepancies in their anatomical and histological description exist in the literature, but such discrepancies are likely due to large variations of these structures. This makes mechanical testing very challenging, requiring the development of advanced methods for characterizing their mechanical properties. This study proposes the use of planar biaxial testing, digital image correlation (DIC), and optical coherence tomography (OCT) to quantify the deformations of the USLs, both in-plane and out-of-plane. Using the gilts as an animal model, the USLs were found to deform significantly less in their main direction (MD) of in vivo loading than in the direction perpendicular to it (PD) at increasing equibiaxial stresses. Under constant equibiaxial loading, the USLs deform over time equally, at comparable rates in both the MD and PD. The thickness of the USLs decreases as the equibiaxial loading increases but, under constant equibiaxial loading, the thickness increases in some specimens and decreases in others. These findings could contribute to the design of new mesh materials that augment the support function of USLs as well as noninvasive diagnostic tools for evaluating the integrity of the USLs.

Three-dimensional self super-resolution for pelvic floor MRI using a convolutional neural network with multi-orientation data training

PURPOSE

High-resolution pelvic magnetic resonance (MR) imaging is important for the high-resolution and high-precision evaluation of pelvic floor disorders (PFDs), but the data acquisition time is long. Because high-resolution three-dimensional (3D) MR data of the pelvic floor are difficult to obtain, MR images are usually obtained in three orthogonal planes: axial, sagittal, and coronal. The in-plane resolution of the MR data in each plane is high, but the through-plane resolution is low. Thus, we aimed to achieve 3D super-resolution using a convolutional neural network (CNN) approach to capture the intrinsic similarity of low-resolution 3D MR data from three orientations.

METHODS

We used a two-dimensional (2D) super-resolution CNN model to solve the 3D super-resolution problem. The residual-in-residual dense block network (RRDBNet) was used as our CNN backbone. For a given set of low through-plane resolution pelvic floor MR data in the axial or coronal or sagittal scan plane, we applied the RRDBNet sequentially to perform super-resolution on its two projected low-resolution views. Three datasets were used in the experiments, including two private datasets and one public dataset. In the first dataset (dataset 1), MR data acquired from 34 subjects in three planes were used to train our super-resolution model, and low-resolution MR data from nine subjects were used for testing. The second dataset (dataset 2) included a sequence of relatively high-resolution MR data acquired in the coronal plane. The public MR dataset (dataset 3) was used to demonstrate the generalization ability of our model. To show the effectiveness of RRDBNet, we used datasets 1 and 2 to compare RRDBNet with interpolation and enhanced deep super-resolution (EDSR) methods in terms of peak signal-to-noise ratio (PSNR) and structural similarity (SSIM) index. As 3D MR data from one view have two projected low-resolution views, different super-resolution orders were compared in terms of PSNR and SSIM. Finally, to demonstrate the impact of super-resolution on the image analysis task, we used datasets 2 and 3 to compare the performance of our method with interpolation on the 3D geometric model reconstruction of the urinary bladder.

RESULTS

A CNN-based method was used to learn the intrinsic similarity among MR acquisitions from different scan planes. Through-plane super-resolution for pelvic MR images was achieved without using high-resolution 3D data, which is useful for the analysis of PFDs.

Mechanics of Uterosacral Ligaments: Current Knowledge, Existing Gaps, and Future Directions

The uterosacral ligaments (USLs) are important anatomical structures that support the uterus and apical vagina within the pelvis. As these structures are over-stretched, become weak, and exhibit laxity, pelvic floor disorders such as pelvic organ prolapse occur. Although several surgical procedures to treat pelvic floor disorders are directed toward the USLs, there is still a lot that is unknown about their function. This manuscript presents a review of the current knowledge on the mechanical properties of the USLs. The anatomy, microstructure, and clinical significance of the USLs are first reviewed. Then, the results of published experimental studies on the in vivo and ex vivo, uniaxial and biaxial tensile tests are compiled. Based on the existing findings, research gaps are identified and future research directions are discussed. The purpose of this exhaustive review is to help new researchers navigate scientific literature on the mechanical properties of the USLs. The use of these structures remains very popular in reconstructive surgeries that restore and augment the support of pelvic organs, especially as synthetic surgical mesh implants continue to be highly controversial.

Effect of mesh anchoring technique in uterine prolapse repair surgery: A finite element analysis

The female pelvic cavity involves muscles, ligaments, endopelvic fasciae and multiple organs where different pathologies may occur, namely the pelvic organ prolapse (POP). The synthetic implants are used for the reconstructive surgery of POP, but severe complications associated with their use have been reported, mainly related to their mechanical properties (e.g., implant stiffness) and microstructure. In this study, we mimicked a transvaginal reconstructive surgery to repair the apical ligaments (uterosacral ligaments (USLs) and cardinal ligaments (CLs)), by modeling, their impairment (90% and 50%) and/or total rupture. The implants to reinforce/replace these ligaments were built based on literature specifications and their mechanical properties were obtained through uniaxial tensile tests. The main aim of this study was to simulate the effect of mesh anchoring technique (simple stich and continuous stitch), and compare the displacement magnitude of the pelvic tissues, during Valsalva maneuver. The absence/presence of the synthetic implant was simulated when total rupture of the CLs and USLs occurs, causing a variation of the vaginal displacement (9% for the CLs and 27% for the USLs). Additionally, the simulations showed that there was a variation of the supero-inferior displacement of the vaginal wall between different anchoring techniques (simple stich and continuous stitch) being approximately of 10% for the simulation USLs and CLs implant. The computational simulation was able to mimic the biomechanical behavior of the USLs and CLs, in response to different anchoring techniques, which can be help improving the outcomes of the prolapse surgery.

From molecular to macro: the key role of the apical ligaments in uterovaginal support

To explain the pathophysiology of pelvic organ prolapse, we must first understand the complexities of the normal support structures of the uterus and vagina. In this review, we focus on the apical ligaments, which include the cardinal and uterosacral ligaments. The aims of this review are the following: (1) to provide an overview of the anatomy and histology of the ligaments; (2) to summarize the imaging and biomechanical studies of the ligament properties and the way they relate to anterior and posterior vaginal wall prolapse; and (3) to synthesize these findings into a conceptual model for the progression of prolapse.

Comparison of Biaxial Biomechanical Properties of Post-menopausal Human Prolapsed and Non-prolapsed Uterosacral Ligament

Uterosacral ligaments (USLs) provide structural support to the female pelvic floor, and a loss of USL structural integrity or biomechanical function may induce pelvic organ prolapse (POP). Alterations in extracellular matrix composition and organization dictate USL mechanical function. Changes in USL microstructure and corresponding mechanical properties, however, are not fully understood, nor is it understood how microstructure and mechanics change with onset and progression of POP. This is due, in part, as USL properties are primarily characterized along a single direction (uniaxial test), whereas the USL is loaded in multiple directions simultaneously within the body. Biaxial testing permits the acquisition of biomechanical data from two axes simultaneously, and thus simulates a more physiologic assessment compared to the traditional uniaxial testing. Therefore, the objective of this study was to quantify the biaxial biomechanical properties and histological composition of the USL in post-menopausal women with and without POP at various stages. Potential correlations between tissue microstructural composition and mechanical function were also examined. Tangential modulus was lower and peak stretch higher in POP III/IV compared to non-POP and POP I/II in the main in vivo loading direction; however, no significant differences in mechanical properties were observed in the perpendicular loading direction. Collagen content positively correlated to tangential modulus in the main in vivo loading direction (r = 0.5, p = 0.02) and negatively correlated with the peak stretch in both the main in vivo (r = -0.5, p = 0.02) and perpendicular loading directions (r = -0.3, p = 0.05). However, no statistically significant differences in USL composition were observed, which may be due to the small sample size and high variability of small sections of human tissues. These results provide first step towards understanding what microstructural and mechanical changes may occur in the USL with POP onset and progression. Such information may provide important future insights into the development of new surgical reconstruction techniques and graft materials for POP treatment.

Development of anatomically based customizable three-dimensional finite-element model of pelvic floor support system: POP-SIM1.0

To develop an anatomically based customizable finite-element (FE) model of the pelvic floor support system to simulate pelvic organ prolapse (POP): POP-SIM1.0. This new simulation platform allows for the construction of an array of models that objectively represent the key anatomical and functional variation in women with and without prolapse to test pathomechanism hypotheses of the prolapse formation. POP-SIM1.0 consists of anatomically based FE models and a suite of Python-based tools developed to rapidly construct FE models by customizing the base model with desired structural parameters. Each model consists of anatomical structures from three support subsystems which can be customized based on magnetic resonance image measurements in women with and without prolapse. The customizable structural parameters include presence of levator ani (LA) avulsion, hiatus size, anterior vaginal wall dimension, attachment fascia length and apical location in addition to the tissue material properties and intra-abdominal pressure loading. After customization, the FE model was loaded with increasing intra-abdominal pressure (0-100 cmH2O) and solved using ABAQUS explicit solver. We were able to rapidly construct anatomically based FE models with specific structural geometry which reflects the morphology changes often observed in women with prolapse. At maximum loading, simulated structural deformations have similar anatomical characteristics to those observed during clinical exams and stress magnetic resonance images. Simulation results showed the presence of LA muscle avulsion negatively impacts the pelvic floor support. The normal model with intact muscle had the smallest exposed vaginal length of 11 mm, while the bilateral avulsion produced the largest exposed vaginal length at 24 mm. The unilateral avulsion model had an exposed vaginal length of 18 mm and also demonstrated a tipped perineal body similar to that seen in clinical observation. Increasing the hiatus size, vaginal wall length and fascia length also resulted in worse pelvic floor support, increasing the exposed vaginal length from 18 mm in the base model to 33 mm, 54 mm and 23.5 mm, respectively. The developed POP-SIM1.0 can simulate the anatomical structure changes often observed in women with prolapse. Preliminary results showed that the presence of LA avulsion, enlarged hiatus, longer vaginal wall and fascia length can result in larger prolapse at simulated maximum Valsalva.

Mechanical Analysis of the Uterosacral Ligament: Swine vs. Human

The uterosacral ligament (USL) is a major suspensory structure of the female pelvic floor, providing support to the cervix and/or upper vagina. It plays a pivotal role in surgical procedures for pelvic organ prolapse (POP) aimed at restoring apical support. Despite its important mechanical function, little is known about the mechanical properties of the USL due to the constraints associated with in vivo testing of human USL and the lack of validated large animal models that enable such investigations. In this study, we provide the first comparison of the mechanical properties of swine and human USLs. Preconditioning and pre-creep data up to a 2 N load and creep data under a 2 N load over 1200 s were obtained on swine (n = 9) and human (n = 9) USL specimens by performing planar equi-biaxial tensile tests and using the digital image correlation method. No differences in the peak strain during preconditioning tests, secant modulus of the pre-creep response, and strain at the end of creep tests were detected in the USLs from the two species along both axial loading directions (the main in vivo loading direction and the direction that is perpendicular to it). These findings suggest that the swine holds promise as large animal model for studying the mechanical role of the USL in apical vaginal support and treatment of POP.

What's new in the functional anatomy of pelvic organ prolapse?

PURPOSE OF REVIEW

Provide an evidence-based review of pelvic floor functional anatomy related to pelvic organ prolapse.

RECENT FINDINGS

Pelvic organ support depends on interactions between the levator ani muscle and pelvic connective tissues. Muscle failure exposes the vaginal wall to a pressure differential producing abnormal tension on the attachments of the pelvic organs to the pelvic sidewall. Birth-induced injury to the pubococcygeal portion of the levator ani muscle is seen in 55% of women with prolapse and 16% of women with normal support. Failure of the lateral connective tissue attachments between the uterus and vagina to the pelvic wall (cardinal, uterosacral, and paravaginal) are strongly related with prolapse (effect sizes ∼2.5) and are also highly correlated with one another (r ∼ 0.85). Small differences exist with prolapse in factors involving the vaginal wall length and width (effect sizes ∼1). The primary difference in ligament properties between women with and without prolapse is found in ligament length. Only minor differences in ligament stiffness are seen.

SUMMARY

Pelvic organ prolapse occurs because of injury to the levator ani muscles and failure of the lateral connections between the pelvic organs to the pelvic sidewall. Abnormalities of the vaginal wall fascial tissues may play a minor role.

Effects of repeated biaxial loads on the creep properties of cardinal ligaments

The cardinal ligament (CL) is one of the major pelvic ligaments providing structural support to the vagina/cervix/uterus complex. This ligament has been studied mainly with regards to its important function in the treatment of different diseases such as surgical repair for pelvic organ prolapse and radical hysterectomy for cervical cancer. However, the mechanical properties of the CL have not been fully determined, despite the important in vivo supportive role of this ligament within the pelvic floor. To advance our limited knowledge about the elastic and viscoelastic properties of the CL, we conducted three consecutive planar equi-biaxial tests on CL specimens isolated from swine. Specifically, the CL specimens were divided into three groups: specimens in group 1 (n = 7) were loaded equi-biaxially to 1 N, specimens in group 2 (n = 8) were loaded equi-biaxially to 2N, and specimens in group 3 (n = 7) were loaded equi-biaxially to 3N. In each group, the equi-biaxial loads of 1N, 2N, or 3N were applied and kept constant for 1200s three times. The two axial loading directions were selected to be the main in-vivo loading direction of the CL and the direction that is perpendicular to it. Using the digital image correlation (DIC) method, the in-plane Lagrangian strains in these two loading directions were measured throughout the tests. The results showed that CL was elastically anisotropic, as statistical differences were found between the mean strains along the two axial loading directions for specimens in group 1, 2, or 3 when the equi-biaxial load reached 1N, 2N, or 3N, respectively. For specimens in group 1 and 2, no statistical differences were detected in the mean normalized strains (or, equivalently, the increase in strain over time) between the two axial loading directions for each creep test. For specimens in group 3, some differences were noted but, by the end of the 3rd creep test, there were no statistical differences in the mean normalized strains between the two axial loading directions. These findings indicated that the increase in strain over time by the end of the 3rd creep test were comparable along these directions. The greatest mean normalized strain (or, equivalently, the largest increase in strain over time) was measured at the end of the 1st creep test (t=1200s), regardless of the equi-biaxial load magnitude or loading direction. Mean normalized strains during the 2nd and 3rd creep tests (t = 100, 600, and 1200s), along each loading direction, were not statistically different. Isochronal data collected at 1N, 2N, or 3N equi-biaxial loads indicated that the CL may be a nonlinear viscoelastic material. Overall, this experimental study offers new knowledge of the mechanical properties of the CL that can guide the development of better treatment methods such as surgical reconstruction for pelvic organ prolapse and radical hysterectomy for cervical cancer.

Intraoperative cervix location and apical support stiffness in women with and without pelvic organ prolapse

BACKGROUND

It is unknown how initial cervix location and cervical support resistance to traction, which we term "apical support stiffness," compare in women with different patterns of pelvic organ support. Defining a normal range of apical support stiffness is important to better understand the pathophysiology of apical support loss.

OBJECTIVE

The aims of our study were to determine whether: (1) women with normal apical support on clinic Pelvic Organ Prolapse Quantification, but with vaginal wall prolapse (cystocele and/or rectocele), have the same intraoperative cervix location and apical support stiffness as women with normal pelvic support; and (2) all women with apical prolapse have abnormal intraoperative cervix location and apical support stiffness. A third objective was to identify clinical and biomechanical factors independently associated with clinic Pelvic Organ Prolapse Quantification point C.

STUDY DESIGN

We conducted an observational study of women with a full spectrum of pelvic organ support scheduled to undergo gynecologic surgery. All women underwent a preoperative clinic examination, including Pelvic Organ Prolapse Quantification. Cervix starting location and the resistance (stiffness) of its supports to being moved steadily in the direction of a traction force that increased from 0-18 N was measured intraoperatively using a computer-controlled servoactuator device. Women were divided into 3 groups for analysis according to their pelvic support as classified using the clinic Pelvic Organ Prolapse Quantification: (1) "normal/normal" was women with normal apical (C < -5 cm) and vaginal (Ba and Bp < 0 cm) support; (2) normal/prolapse had normal apical support (C < -5 cm) but prolapse of the anterior or posterior vaginal walls (Ba and/or Bp ≥ 0 cm); and (3) prolapse/prolapse had both apical and vaginal wall prolapse (C > -5 cm and Ba and/or Bp ≥ 0 cm). Demographics, intraoperative cervix locations, and apical support stiffness values were then compared. Normal range of cervix location during clinic examination and operative testing was defined by the total range of values observed in the normal/normal group. The proportion of women in each group with cervix locations within and outside the normal range was determined. Linear regression was performed to identify variables independently associated with clinic Pelvic Organ Prolapse Quantification point C.

RESULTS

In all, 52 women were included: 14 in the normal/normal group, 11 in the normal/prolapse group, and 27 in the prolapse/prolapse group. At 1 N of traction force in the operating room, 50% of women in the normal/prolapse group had cervix locations outside the normal range while 10% had apical support stiffness outside the normal range. Of women in the prolapse/prolapse group, 81% had cervix locations outside the normal range and 8% had apical support stiffness outside the normal range. Similar results for cervix locations were observed at 18 N of traction force; however the proportion of women with apical support stiffness outside the normal range increased to 50% in the normal/prolapse group and 59% in the prolapse/prolapse group. The prolapse/prolapse group had statistically lower apical support stiffness compared to the normal/normal group with increased traction from 1-18 N (0.47 ± 0.18 N/mm vs 0.63 ± 0.20 N/mm, P = .006), but all other comparisons were nonsignificant. After controlling for age, parity, body mass index, and apical support stiffness, cervix location at 1 N traction force remained an independent predictor of clinic Pelvic Organ Prolapse Quantification point C, but only in the prolapse/prolapse group.

CONCLUSION

Approximately 50% of women with cystocele and/or rectocele but normal apical support in the clinic had cervix locations outside the normal range under intraoperative traction, while 19% of women with uterine prolapse had normal apical support. Identifying women whose apical support falls outside a defined normal range may be a more accurate way to identify those who truly need a hysterectomy and/or an apical support procedure and to spare those who do not.

Micro-structural and Biaxial Creep Properties of the Swine Uterosacral-Cardinal Ligament Complex

The uterosacral ligament and cardinal ligament (USL/CL) complex is the major suspensory tissue of the uterus, cervix, and vagina. This tissue is subjected primarily to bi-axial forces in-vivo that significantly alter its structure and dimension over time, compromising its support function and leading to pelvic floor disorders. In this study, we present the first rigorous characterization of the collagen fiber microstructure and creep properties of the swine USL/CL complex by using scanning electron microscopy and planar biaxial testing in combination with three-dimensional digital image correlation. Collagen fiber bundles were found to be arranged into layers. Although the fiber bundles were oriented in multiple directions, 80.8% of them were aligned within ±45[Formula: see text] to the main in-vivo loading direction. The straightness parameter, defined as the ratio of the end-to-end distance of a fiber bundle to its length, varied from 0.28 to 1.00, with 95.2% fiber bundles having a straightness parameter between 0.60 and 1.00. Under constant equi-biaxial loads of 2 and 4 N, the USL/CL complex exhibited significant creep both along the main in-vivo loading direction (the parallel direction) and along the direction perpendicular to it (the perpendicular direction). Specifically, over a 120-min period, the mean strain increased by 20-34[Formula: see text] in the parallel direction and 33-41[Formula: see text] in the perpendicular direction. However, there was no statistically significant difference in creep strains observed after 120 min between the parallel and perpendicular directions for either the 2 or 4 N load case. Creep proceeded slightly faster in the perpendicular direction under the equi-biaxial load of 2 N than under the equi-biaxial load of 4 N ([Formula: see text]). It proceeded significantly faster in the parallel direction under the equi-biaxial loads of 2 N than under the equi-biaxial loads of 4 N ([Formula: see text]). Overall, our findings contribute to a greater understanding of the biomaterial properties of the USL/CL complex that is needed for the development of new surgical reconstruction methods and mesh materials for pelvic floor disorders.

3D finite element modeling of pelvic organ prolapse

OBJECTIVES

The purpose of this study is to develop a validated 3D finite element model of the pelvic floor system which can offer insights into the mechanics of anterior vaginal wall prolapse and have the ability to assess biomedical device treatment methods. The finite element results should accurately mimic the clinical findings of prolapse due to intra-abdominal pressure (IAP) and soft tissues impairment conditions.

METHODS

A 3D model of pelvic system was created in Creo Parametric 2.0 based on MRI Images, which included uterus, cervix, vagina, cardinal ligaments, uterosacral ligaments, and a simplified levator plate and rectum. The geometrical model was imported into ANSYS Workbench 14.5. Mechanical properties of soft tissues were based on experimental data of tensile test results from current literature. Studies were conducted for IAP loadings on the vaginal wall and uterus, increasing from lowest to extreme values.

RESULTS

Anterior vaginal wall collapse occurred at an IAP value corresponding to maximal valsalva and showed similar collapsed shape as clinical findings. Prolapse conditions exhibited high sensitivity to vaginal wall stiffness, whereas healthy tissues was found to support the vagina against prolapse. Ligament impairment was found to have only a secondary effect on prolapse.

Traction force needed to reproduce physiologically observed uterine movement: technique development, feasibility assessment, and preliminary findings

INTRODUCTION AND HYPOTHESIS

This study aimed to describe a novel strategy to determine the traction forces needed to reproduce physiologic uterine displacement in women with and without prolapse.

METHODS

Participants underwent dynamic stress magnetic resonance imaging (MRI) testing as part of a study examining apical uterine support. Physiologic uterine displacement was determined by analyzing uterine location in images taken at rest and at maximal Valsalva. Force-displacement curves were calculated based on intraoperative cervical traction testing. The intraoperative force required to achieve the uterine displacement measured during MRI was then estimated from these curves. Women were categorized into three groups based on pelvic organ support: group 1 (normal apical and vaginal support), group 2 (normal apical support but vaginal prolapse present), and group 3 (apical prolapse).

RESULTS

Data from 19 women were analyzed: five in group 1, five in group 2, and nine in group 3. Groups were similar in terms of age, body mass index (BMI), and parity. Median operating room (OR) force required for uterine displacement measured during MRI was 0.8 N [interquartile range (IQR) 0.62-3.22], and apical ligament stiffness determined using MRI uterine displacement was 0.04 N/mm (IQR 0.02-0.08); differences between groups were nonsignificant. Uterine locations determined at rest and during maximal traction were lower in the OR compared with MRI in all groups.

CONCLUSIONS

Using this investigative strategy, we determined that only 0.8 N of traction force in the OR was required to achieve maximal physiologic uterine displacement seen during dynamic (maximal Valsalva) MRI testing, regardless of the presence or absence of prolapse.

A multi-compartment 3-D finite element model of rectocele and its interaction with cystocele

We developed a subject-specific 3-D finite element model to understand the mechanics underlying formation of female pelvic organ prolapse, specifically a rectocele and its interaction with a cystocele. The model was created from MRI 3-D geometry of a healthy 45 year-old multiparous woman. It included anterior and posterior vaginal walls, levator ani muscle, cardinal and uterosacral ligaments, anterior and posterior arcus tendineus fascia pelvis, arcus tendineus levator ani, perineal body, perineal membrane and anal sphincter. Material properties were mostly from the literature. Tissue impairment was modeled as decreased tissue stiffness based on previous clinical studies. Model equations were solved using Abaqus v 6.11. The sensitivity of anterior and posterior vaginal wall geometry was calculated for different combinations tissue impairments under increasing intraabdominal pressure. Prolapse size was reported as pelvic organ prolapse quantification system (POP-Q) point at point Bp for rectocele and point Ba for cystocele. Results show that a rectocele resulted from impairments of the levator ani and posterior compartment support. For 20% levator and 85% posterior support impairments, simulated rectocele size (at POP-Q point: Bp) increased 0.29 mm/cm H2O without apical impairment and 0.36 mm/cm H2O with 60% apical impairment, as intraabdominal pressures increased from 0 to 150 cm H2O. Apical support impairment could result in the development of either a cystocele or rectocele. Simulated repair of posterior compartment support decreased rectocele but increased a preexisting cystocele. We conclude that development of rectocele and cystocele depend on the presence of anterior, posterior, levator and/or or apical support impairments, as well as the interaction of the prolapse with the opposing compartment.

Histo-mechanical properties of the swine cardinal and uterosacral ligaments

The focus of this study was to determine the structural and mechanical properties of two major ligaments that support the uterus, cervix, and vagina: the cardinal ligament (CL) and the uterosacral ligament (USL). The adult swine was selected as animal model. Histological analysis was performed on longitudinal and cross sections of CL and USL specimens using Masson׳s trichrome and Verhoeff-van Giesson staining methods. Scanning electron microscopy was employed to visualize the through-thickness organization of the collagen fibers. Quasi-static uniaxial tests were conducted on specimens that were harvested from the CL/USL complex of a single swine. Dense connective tissue with a high content of elastin and collagen fibers was observed in the USL. Loose connective tissue with a considerable amount of smooth muscle cells and ground substance was detected in both the CL and USL. Collagen fibers, smooth muscle cells, blood vessels, and nerve fibers were arranged primarily in the plane of the ligaments. The USL was significantly stronger than the CL with higher ultimate stress and tangent modulus of the linear region of the stress-strain curve. Knowledge about the mechanical properties of the CL and USL will aid in the design of novel mesh materials, stretching routines, and surgical procedures for pelvic floor disorders.

Biaxial mechanical properties of swine uterosacral and cardinal ligaments

Mechanical alterations to pelvic floor ligaments may contribute to the development and progression of pelvic floor disorders. In this study, the first biaxial elastic and viscoelastic properties were determined for uterosacral ligament (USL) and cardinal ligament (CL) complexes harvested from adult female swine. Biaxial stress-stretch data revealed that the ligaments undergo large strains. They are orthotropic, being typically stiffer along their main physiological loading direction (i.e., normal to the upper vaginal wall). Biaxial stress relaxation data showed that the ligaments relax equally in both loading directions and more when they are less stretched. In order to describe the experimental findings, a three-dimensional constitutive law based on the Pipkin-Rogers integral series was formulated. The model accounts for incompressibility, large deformations, nonlinear elasticity, orthotropy, and stretch-dependent stress relaxation. This combined theoretical and experimental study provides new knowledge about the mechanical properties of USLs and CLs that could lead to the development of new preventive and treatment methods for pelvic floor disorders.