Lightweight, strong, moldable wood via cell wall engineering as a sustainable structural material

Leakage Proof, Flame-Retardant, and Electromagnetic Shield Wood Morphology Genetic Composite Phase Change Materials for Solar Thermal Energy Harvesting

Phase change materials (PCMs) offer a promising solution to address the challenges posed by intermittency and fluctuations in solar thermal utilization. However, for organic solid-liquid PCMs, issues such as leakage, low thermal conductivity, lack of efficient solar-thermal media, and flammability have constrained their broad applications. Herein, we present an innovative class of versatile composite phase change materials (CPCMs) developed through a facile and environmentally friendly synthesis approach, leveraging the inherent anisotropy and unidirectional porosity of wood aerogel (nanowood) to support polyethylene glycol (PEG). The wood modification process involves the incorporation of phytic acid (PA) and MXene hybrid structure through an evaporation-induced assembly method, which could impart non-leaking PEG filling while concurrently facilitating thermal conduction, light absorption, and flame-retardant. Consequently, the as-prepared wood-based CPCMs showcase enhanced thermal conductivity (0.82 W m-1 K-1, about 4.6 times than PEG) as well as high latent heat of 135.5 kJ kg-1 (91.5% encapsulation) with thermal durability and stability throughout at least 200 heating and cooling cycles, featuring dramatic solar-thermal conversion efficiency up to 98.58%. In addition, with the synergistic effect of phytic acid and MXene, the flame-retardant performance of the CPCMs has been significantly enhanced, showing a self-extinguishing behavior. Moreover, the excellent electromagnetic shielding of 44.45 dB was endowed to the CPCMs, relieving contemporary health hazards associated with electromagnetic waves. Overall, we capitalize on the exquisite wood cell structure with unidirectional transport inherent in the development of multifunctional CPCMs, showcasing the operational principle through a proof-of-concept prototype system.

Co-Adjusting d-Band Center of Fe to Accelerate Proton Coupling for Efficient Oxygen Electrocatalysis

The problem in d-band center modulation of transition metal-based catalysts for the rate-determining steps of oxygen conversion is an obstacle to boost the electrocatalytic activity by accelerating proton coupling. Herein, the Co doping to FeP is adopted to modify the d-band center of Fe. Optimized Fe sites accelerate the proton coupling of oxygen reduction reaction (ORR) on N-doped wood-derived carbon through promoting water dissociation. In situ generated Fe sites optimize the adsorption of oxygen-related intermediates of oxygen evolution reaction (OER) on CoFeP NPs. Superior catalytic activity toward ORR (half-wave potential of 0.88 V) and OER (overpotential of 300 mV at 10 mA cm-2) express an unprecedented level in carbon-based transition metal-phosphide catalysts. The liquid zinc-air battery presents an outstanding cycling stability of 800 h (2400 cycles). This research offers a newfangled perception on designing highly efficient carbon-based bifunctional catalysts for ORR and OER.

Gradient matters via filament diameter-adjustable 3D printing

Gradient matters with hierarchical structures endow the natural world with excellent integrity and diversity. Currently, direct ink writing 3D printing is attracting tremendous interest, and has been used to explore the fabrication of 1D and 2D hierarchical structures by adjusting the diameter, spacing, and angle between filaments. However, it is difficult to generate complex 3D gradient matters owing to the inherent limitations of existing methods in terms of available gradient dimension, gradient resolution, and shape fidelity. Here, we report a filament diameter-adjustable 3D printing strategy that enables conventional extrusion 3D printers to produce 1D, 2D, and 3D gradient matters with tunable heterogeneous structures by continuously varying the volume of deposited ink on the printing trajectory. In detail, we develop diameter-programmable filaments by customizing the printing velocity and height. To achieve high shape fidelity, we specially add supporting layers at needed locations. Finally, we showcase multi-disciplinary applications of our strategy in creating horizontal, radial, and axial gradient structures, letter-embedded structures, metastructures, tissue-mimicking scaffolds, flexible electronics, and time-driven devices. By showing the potential of this strategy, we anticipate that it could be easily extended to a variety of filament-based additive manufacturing technologies and facilitate the development of functionally graded structures.

Dynamic Thermostable Cellulosic Triboelectric Materials from Multilevel-Non-Covalent Interactions

Triboelectric materials present great potential for harvesting huge amounts of dispersed energy, and converting them directly into useful electricity, a process that generates power more sustainably. Triboelectric nanogenerators (TENGs) have emerged as a technology to power electronics and sensors, and it is expected to solve the problem of energy harvesting and self-powered sensing from extreme environments. In this paper, a high-temperature-resistant triboelectric material is designed based on multilevel non-covalent bonding interactions, which achieves an ultra-high surface charge density of 192 µC m-2 at high temperatures. TENGs based on the triboelectric material exhibit more than an order of magnitude higher power output (2750 mW m-2 at 200 °C) than the existing devices at high temperatures. These remarkable properties are achieved based on enthalpy-driven molecular assembly in highly unbonded states. Thus, the material maintains bond strength and ultra-high surface charge density in entropy-dominated high-temperature environments. This molecular design concept points out a promising direction for the preparation of polymers with excellent triboelectric properties.

Releasing Free Radicals in Precursor Triggers the Formation of Closed Pores in Hard Carbon for Sodium-Ion Batteries

Increasing closed pore volume in hard carbon is considered to be the most effective way to enhance the electrochemical performance in sodium-ion batteries. However, there is a lack of systematic insights into the formation mechanisms of closed pores at molecular level. In this study, a regulation strategy of closed pores via adjustment of the content of free radicals is reported. Sufficient free radicals are exposed by part delignification of bamboo, which is related to the formation of well-developed carbon layers and rich closed pores. In addition, excessive free radicals from nearly total delignification lead to more reactive sites during pyrolysis, which competes for limited precursor debris to form smaller microcrystals and therefore compact the material. The optimal sample delivers a large closed pore volume of 0.203 cm3 g-1, which leads to a high reversible capacity of 350 mAh g-1 at 20 mA g-1 and enhanced Na+ transfer kinetics. This work provides insights into the formation mechanisms of closed pores at molecular level, enabling rational design of hard carbon pore structures.

Lightweight and Strong Cellulosic Triboelectric Materials Enabled by Cell Wall Nanoengineering

As intelligent technology surges forward, wearable electronics have emerged as versatile tools for monitoring health and sensing our surroundings. Among these advancements, porous triboelectric materials have garnered significant attention for their lightness. However, these materials face the challenge of improving structural stability to further enhance the sensing accuracy of triboelectric sensors. In this study, a lightweight and strong porous cellulosic triboelectric material is designed by cell wall nanoengineering. By tailoring of the cell wall structure, the material shows a high mechanical strength of 51.8 MPa. The self-powered sensor constructed by this material has a high sensitivity of 33.61 kPa-1, a fast response time of 36 ms, and excellent pressure detection durability. Notably, the sensor still enables a high sensing performance after the porous cellulosic triboelectric material exposure to 200 °C and achieves real-time feedback of human motion, thereby demonstrating great potential in the field of wearable electronic devices.

Study of ternary deep eutectic solvents to enhance the bending properties of ash wood

Deep eutectic solvents (DESs) are considered one of the most promising biomass pretreatment reagents, and their research applications in woody fibrous biomass are increasing yearly. Inspired by the research related to wood bending, we explored the effects of different DES systems on the bending development of wood, and the results showed that the addition of anhydrous ferric trichloride to the DES system of lactic acid/choline chloride could enhance the treatment effect that increased the bendability and torsion resistance of ash wood. The anhydrous FeCl3 could act as an active site and provide acidic protons to improve the treatment efficiency of DES. In addition, the addition of an appropriate amount of water can reduce the viscosity of the DES system, and the highest lignin removal rate was obtained at 10 wt% of water in the DES, which resulted in the best mechanical properties and tensile resilience of ash wood, with the tensile strength and stability of 97 MPa and 13.6%, respectively, as determined by experiments with different water contents in different mass fractions. Therefore, using a DES can effectively improve the bending properties of wood.

Biomass-Derived Catalytically Active Carbon Materials for the Air Electrode of Zn-air Batteries

Given the growing environmental and energy problems, developing clean, renewable electrochemical energy storage devices is of great interest. Zn-air batteries (ZABs) have broad prospects in energy storage because of their high specific capacity and environmental friendliness. The unavailability of cheap air electrode materials and effective and stable oxygen electrocatalysts to catalyze air electrodes are main barriers to large-scale implementation of ZABs. Due to the abundant biomass resources, self-doped heteroatoms, and unique pore structure, biomass-derived catalytically active carbon materials (CACs) have great potential to prepare carbon-based catalysts and porous electrodes with excellent performance for ZABs. This paper reviews the research progress of biomass-derived CACs applied to ZABs air electrodes. Specifically, the principle of ZABs and the source and preparation method of biomass-derived CACs are introduced. To prepare efficient biomass-based oxygen electrocatalysts, heteroatom doping and metal modification were introduced to improve the efficiency and stability of carbon materials. Finally, the effects of electron transfer number and H2 O2 yield in ORR on the performance of ZABs were evaluated. This review aims to deepen the understanding of the advantages and challenges of biomass-derived CACs in the air electrodes of ZABs, promote more comprehensive research on biomass resources, and accelerate the commercial application of ZABs.

Tough and Moldable Sustainable Cellulose-Based Structural Materials via Multiscale Interface Engineering

All-natural materials derived from cellulose nanofibers (CNFs) are expected to be used to replace engineering plastics and have attracted much attention. However, the lack of crack extension resistance and 3D formability of nanofiber-based structural materials hinders their practical applications. Here, a multiscale interface engineering strategy is reported to construct high-performance cellulose-based materials. The sisal microfibers are surface treated to expose abundant active CNFs with positive charges, thereby enhancing their interfacial combination with the negatively charged CNFs. The robust multiscale dual network enables easy molding of multiscale cellulose-based structural materials into complex 3D special-shaped structures, resulting in nearly twofold and fivefold improvements in toughness and impact resistance compared with those of CNFs-based materials. Moreover, this multiscale interface engineering strategy endows cellulose-based structural materials with better comprehensive performance than petrochemical-based plastics and broadens cellulose's potential for lightweight applications as structural materials with lower environmental effects.

A Bioinspired Gradient Design Strategy for Cellulose-Based Electromagnetic Wave Absorbing Structural Materials

Cellulose nanofiber (CNF) possesses excellent intrinsic properties, and many CNF-based high-performance structural and functional materials have been developed recently. However, the coordination of the mechanical properties and functionality is still a considerable challenge. Here, a CNF-based structural material is developed by a bioinspired gradient structure design using hollow magnetite nanoparticles and the phosphorylation-modified CNF as building blocks, which simultaneously achieves a superior mechanical performance and electromagnetic wave absorption (EMA) ability. Benefiting from the gradient design, the flexural strength of the structural material reached ∼205 MPa. Meanwhile, gradient design improves impedance matching, contributing to the high EMA ability (-59.5 dB) and wide effective absorption width (5.20 GHz). Besides, a low coefficient of thermal expansion and stable storage modulus was demonstrated as the temperature changes. The excellent mechanical, thermal, and EMA performance exhibited great potential for application in stealth equipment and electromagnetic interference protecting electronic packaging materials.

Atomistic, macromolecular model of the Populus secondary cell wall informed by solid-state NMR

Plant secondary cell walls (SCWs) are composed of a heterogeneous interplay of three major biopolymers: cellulose, hemicelluloses, and lignin. Details regarding specific intermolecular interactions and higher-order architecture of the SCW superstructure remain ambiguous. Here, we use solid-state nuclear magnetic resonance (ssNMR) measurements to infer refined details about the structural configuration, intermolecular interactions, and relative proximity of all three major biopolymers within air-dried Populus wood. To enhance the utility of these findings and enable evaluation of hypotheses in a physics-based environment in silico, the NMR observables are articulated into an atomistic, macromolecular model for biopolymer assemblies within the plant SCW. Through molecular dynamics simulation, we quantitatively evaluate several variations of atomistic models to determine structural details that are corroborated by ssNMR measurements.

Farming on the Ocean via Desalination (FOOD)

Today, agricultural irrigation consumes the largest amount of freshwater globally, while humans are threatened by water scarcity. To eliminate the trade-off between hunger and thirst, here, we show off-grid maritime agriculture based on a floating solar-driven agro-desalination wooden dome. In this dome, part of the visible light is transmitted for photosynthesis, and the remaining solar energy drives solar desalination, providing enough water (>4 mm day-1) for irrigation. Based on this water-food synergy, the stages of germination and growth are demonstrated. This technology can, to a large extent, support food security and sustainable agriculture and, in principle, be used to create self-circulation systems at sea to help humans survive weather extremes such as floods and droughts.

Shape and Stiffness Switchable Hydroplastic Wood with Programmability and Reproducibility

Stiffness switchable materials (e.g., supramolecular polymers, metals) that alter their shape and mechanical properties in response to specific stimuli are potentially utilized in the structural engineering field but still limited due to the use of petroleum-based synthetic monomers and large energy consumption. Herein, a sustainable and facile solvent casting strategy is proposed to fabricate the "hydroplastic wood" with shape and stiffness switchable properties via cell wall wetting, cell wall softening and subsequent moisture evaporation. Therein, a wetting agent with low surface tension and low viscosity is utilized for covering the rough surface of solid wood to form a liquid lubricating layer, thereby increasing the interfacial wettability and achieving uniform softening of the cell walls. This interface wetting treatment can easily break through the hydro-plasticization process for thick wood (Balsa wood, Ochroma lagopus Swartz, density: 0.25 g/cm3; Pinewood, Pinus armandii, density: 0.38 g/cm3). Additionally, the capillary force arising from moisture evaporation induces the self-densification of oriented cellulose nanofibrils and achieves moisture-mediated shape design capabilities through periodic saturation-dehydration. This work makes hydroplastic wood a promising candidate for engineering materials because of its combined advantages of strong durability, formability, and load-carrying capacity.

The Critical Roles of Water in the Processing, Structure, and Properties of Nanocellulose

The cellulose industry depends heavily on water owing to the hydrophilic nature of cellulose fibrils and its potential for sustainable and innovative production methods. The emergence of nanocellulose, with its excellent properties, and the incorporation of nanomaterials have garnered significant attention. At the nanoscale level, nanocellulose offers a higher exposure of hydroxyl groups, making it more intimate with water than micro- and macroscale cellulose fibers. Gaining a deeper understanding of the interaction between nanocellulose and water holds the potential to reduce production costs and provide valuable insights into designing functional nanocellulose-based materials. In this review, water molecules interacting with nanocellulose are classified into free water (FW) and bound water (BW), based on their interaction forces with surface hydroxyls and their mobility in different states. In addition, the water-holding capacity of cellulosic materials and various water detection methods are also discussed. The review also examines water-utilization and water-removal methods in the fabrication, dispersion, and transport of nanocellulose, aiming to elucidate the challenges and tradeoffs in these processes while minimizing energy and time costs. Furthermore, the influence of water on nanocellulose properties, including mechanical properties, ion conductivity, and biodegradability, are discussed. Finally, we provide our perspective on the challenges and opportunities in developing nanocellulose and its interplay with water.

Reconstruction of Cellulose Intermolecular Interactions from Hydrogen Bonds to Dynamic Covalent Networks Enables a Thermo-processable Cellulosic Plastic with Tunable Strength and Toughness

Its excellent renewability and biodegradability make cellulose an attractive resource to prepare fossil-based plastic alternatives. However, cellulose itself exhibits strong intermolecular hydrogen bond (H-bond) interactions, significantly restricting the mobility of cellulose chains, thus leading to poor thermo-processing performance. Here, we reconstructed the intermolecular interactions of cellulose chains via replacing the original H-bonds with dynamic covalent bonds. By this, cellulose can be easily thermo-processed into a cellulosic plastic under mild conditions (70 °C). Through adjusting the chemical structure of dynamic covalent networks, the cellulosic plastic shows tunable mechanical strength (3.0-33.5 MPa) and toughness (43-321 kJ m-2). The cellulosic plastic also exhibits excellent resistance to water, organic solvent, acid solution, alkali solution, and high temperature (>400 °C). Moreover, it owns good chemical and biological degradability and recyclability. This work provides an effective method to develop high-performance cellulosic plastics for fossil-based plastic substitution.

Redesigning Natural Materials for Energy, Water, Environment, and Devices

The United Nations Framework Convention on Climate Change (UNFCCC) acknowledges that global cooperation is paramount to mitigate climate change and further warming. The global community is committed to renewable energy and natural materials to tackle this challenge for all humankind. The widespread use of natural materials is embraced as one such action to reach net-zero carbon emissions. Given the hierarchical framework and earth abundance, cellulose-based materials extend their negative carbon benefits to our daily products and accelerate our pace toward carbon neutrality. Here, we present an overview of recent developments of cellulose-based materials in upsurging applications in radiative cooling, thermal insulation, nanofluidics, and wearable devices. We also highlight various modifications and functionalized processes that transform massive amounts of cellulose into green products. The prosperous development of functionalized cellulose materials aligns with a circular economy. Expedited interdisciplinary fundamental investigations are expected to make fibrillated cellulose penetrate more into carbon downdraw at speed and scale.

Novel Wood-Based Functional Material with Vibration and Noise Reduction

As a kind of typical green material, natural materials tend to exhibit excellent performance in the engineering field because of their structure and special functions. The homogeneous vessels of red willow (RW) are potentially unique structures to store lubricants or reinforcing agents to present special functions for engineering applications. A series of novel red willow wood-based composites, which were infused with nano-MoS2 and then reinforced by the epoxy, were developed. Their self-lubricating, mechanical vibration and noise reduction performances were investigated, and the friction, vibration, and noise reduction mechanisms were disclosed. The infusion MoS2 treatment was very beneficial for improving the tribological properties of MoS2-curing epoxy/red willow (MCW), and the coefficient of friction (COF) was reduced by 65.8% under water-lubricated friction after infusing 24 times. Meanwhile, the mechanical performances of MCW were obviously enhanced through the curing treatment of the epoxy. The synergistic effects of the infusion and curing treatments significantly decreased the wear phenomena on the friction surfaces of MCW and weakened the COF and its fluctuation amplitudes, which resulted in the presented excellent vibration and noise reduction performance. The knowledge gained herein could not only develop a novel wood-based composite with low COF and good vibration reduction properties in the engineering field but also provide a new methodology for the design of artificial porous materials with stable and smooth friction processes.

Bamboo-like dual-phase nanostructured copper composite strengthened by amorphous boron framework

Grain boundary engineering is a versatile tool for strengthening materials by tuning the composition and bonding structure at the interface of neighboring crystallites, and this method holds special significance for materials composed of small nanograins where the ultimate strength is dominated by grain boundary instead of dislocation motion. Here, we report a large strengthening of a nanocolumnar copper film that comprises columnar nanograins embedded in a bamboo-like boron framework synthesized by magnetron sputtering co-deposition, reaching the high nanoindentation hardness of 10.8 GPa among copper alloys. The boron framework surrounding copper nanograins stabilizes and strengthens the nanocolumnar copper film under indentation, benefiting from the high strength of the amorphous boron framework and the constrained deformation of copper nanocolumns confined by the boron grain boundary. These findings open a new avenue for strengthening metals via construction of dual-phase nanocomposites comprising metal nanograins embedded in a strong and confining light-element grain boundary framework.

Multiplex CRISPR editing of wood for sustainable fiber production

The domestication of forest trees for a more sustainable fiber bioeconomy has long been hindered by the complexity and plasticity of lignin, a biopolymer in wood that is recalcitrant to chemical and enzymatic degradation. Here, we show that multiplex CRISPR editing enables precise woody feedstock design for combinatorial improvement of lignin composition and wood properties. By assessing every possible combination of 69,123 multigenic editing strategies for 21 lignin biosynthesis genes, we deduced seven different genome editing strategies targeting the concurrent alteration of up to six genes and produced 174 edited poplar variants. CRISPR editing increased the wood carbohydrate-to-lignin ratio up to 228% that of wild type, leading to more-efficient fiber pulping. The edited wood alleviates a major fiber-production bottleneck regardless of changes in tree growth rate and could bring unprecedented operational efficiencies, bioeconomic opportunities, and environmental benefits.

Hygrothermic Wood Actuated Robotic Hand

Stimulus-responsive actuators play a vital role in the new generation of intelligent systems. However, poor mechanical performance, complicated fabrication processes, and the inability to complex deformation limit their practical applications. Herein, these challenges are overcome via designing a strong hygrothermic wood actuator with asymmetric water affinity. The actuator is readily constructed by sandwiching polypyrrole-coated wood with a Ni complex hygroscopic gel top layer for moisture absorption and a polyimide bottom layer as the water barrier. The resulting hygrothermic wood spontaneously stretches and bends itself in response to moisture and thermal/light stimulation. A robotic hand and a series of grippers made of hygrothermic wood demonstrate dexterous object-hand interactions during grasping and holding, while the reversible hygrothermic property allows the actuator to be potentially applied in fire rescue scenarios to rescue trapped objects. A combination of good mechanical properties, multi-stimulus-response, complex deformation, wide working temperature range, low manufacturing cost, and biocompatibility are simultaneously realized by one device. It is thus believed that such a strong wood actuator will open up a new avenue for building intelligent robotic hand systems.

Recent advances in the control of volatile organic compounds emissions from indoor wood-based panels: A comprehensive review

Wood-based panels provide efficient alternatives to materials such as plastics derived from traditional petroleum sources and thereby help to mitigate greenhouse gas emissions. Unfortunately, using indoor manufactured panel products also results in significant emissions of volatile organic compounds including olefins, aromatic and ester compounds, which negatively affect human health. This paper highlights recent developments and notable achievements in the field of indoor hazardous air treatment technologies to guide future research toward environmentally friendly and economically feasible directions that may have a significant impact on the improvement of human settlements. Summarizing and synthesizing the principles, advantages, and limitations of different technologies can assist policymakers and engineers in identifying the most appropriate technology for a particular air pollution control program based on criteria such as cost-effectiveness, efficiency, and environmental impact. In addition, insights into the development of indoor air pollution control technologies are provided and potential areas for innovation, improvement of existing technologies, and development of new technologies are identified. Finally, the authors also hope that this sub-paper will raise public awareness of indoor air pollution issues and promote a better understanding of the importance of indoor air pollution control technologies for public health, environmental protection, and sustainable development.

Corn stalk pith-based hydrophobic aerogel for efficient oil sorption

Bio-based aerogel has become an attractive sorbent for spilled oil and organic pollutants because of its light weight, high porosity and strong sorption capacity. However, the current fabrication process is mainly "bottom-up" technology, which is cost-expensive, time-consuming, and energy-intensive. Herein, we report a top-down, green, efficient and selective sorbent prepared from corn stalk pith (CSP) using the deep eutectic solvent (DES) treatment, followed by TEMPO/NaClO/NaClO₂ oxidization and microfibrillation, and then hexamethyldisilazane coating. Such chemical treatments selectively removed lignin and hemicellulose, broke the thin cell walls of natural CSP, forming an aligned porous structure with capillary channels. The resultant aerogels had a density of 29.3 mg/g, a porosity of 98.13%, and a water contact angle of 130.5^◦, exhibiting excellent oil/organic solvents sorption performance, with a high sorption capacity in the range of 25.4-36.5 g/g, approximately 5-16-fold higher than CSP, and with fast absorption speed and good reusability.

Ion-Electron Coupling Enables Ionic Thermoelectric Material with New Operation Mode and High Energy Density

Ionic thermoelectrics (i-TE) possesses great potential in powering distributed electronics because it can generate thermopower up to tens of millivolts per Kelvin. However, as ions cannot enter external circuit, the utilization of i-TE is currently based on capacitive charge/discharge, which results in discontinuous working mode and low energy density. Here, we introduce an ion-electron thermoelectric synergistic (IETS) effect by utilizing an ion-electron conductor. Electrons/holes can drift under the electric field generated by thermodiffusion of ions, thus converting the ionic current into electrical current that can pass through the external circuit. Due to the IETS effect, i-TE is able to operate continuously for over 3000 min. Moreover, our i-TE exhibits a thermopower of 32.7 mV K-1 and an energy density of 553.9 J m-2, which is more than 6.9 times of the highest reported value. Consequently, direct powering of electronics is achieved with i-TE. This work provides a novel strategy for the design of high-performance i-TE materials.

Sustainability in Wood Products: A New Perspective for Handling Natural Diversity

Wood is a renewable resource with excellent qualities and the potential to become a key element of a future bioeconomy. The increasing environmental awareness and drive to achieve sustainability is leading to a resurgence of research on wood materials. Nevertheless, the global climate changes and associated consequences will soon challenge the wood-value chains in several regions (e.g., central Europe). To cope with these challenges, it is necessary to rethink the current practice of wood sourcing and transformation. The goal of this review is to address the intrinsic natural diversity of wood, from its origin to its technological consequences for the present and future manufacturing of wood products. So far, industrial processes have been optimized to repress the variability of wood properties, enabling more efficient processing and production of reliable products. However, the need to preserve biodiversity and the impact of climate change on forests call for new wood processing techniques and green chemistry protocols for wood modification as enabling factors necessary for managing a more diverse wood provision in the future. This article discusses the past developments that have resulted in the current wood value chains and provides a perspective about how natural variability could be turned into an asset for making truly sustainable wood products. After briefly introducing the chemical and structural complexity of wood, the methods conventionally adopted for industrial homogenization and modification of wood are discussed in relation to their evolution toward increased sustainability. Finally, a perspective is given on technological potentials of machine learning techniques and of novel functional wood materials. Here the main message is that through a combination of sustainable forestry, adherence to green chemistry principles and adapted processes based on machine learning, the wood industry could not only overcome current challenges but also thrive in the near future despite the awaiting challenges.

Emerging Engineered Wood for Building Applications

The building sector, including building operations and materials, was responsible for the emission of ∼11.9 gigatons of global energy-related CO₂ in 2020, accounting for 37% of the total CO₂ emissions, the largest share among different sectors. Lowering the carbon footprint of buildings requires the development of carbon-storage materials as well as novel designs that could enable multifunctional components to achieve widespread applications. Wood is one of the most abundant biomaterials on Earth and has been used for construction historically. Recent research breakthroughs on advanced engineered wood products epitomize this material's tremendous yet largely untapped potential for addressing global sustainability challenges. In this review, we explore recent developments in chemically modified wood that will produce a new generation of engineered wood products for building applications. Traditionally, engineered wood products have primarily had a structural purpose, but this review broadens the classification to encompass more aspects of building performance. We begin by providing multiscale design principles of wood products from a computational point of view, followed by discussion of the chemical modifications and structural engineering methods used to modify wood in terms of its mechanical, thermal, optical, and energy-related performance. Additionally, we explore life cycle assessment and techno-economic analysis tools for guiding future research toward environmentally friendly and economically feasible directions for engineered wood products. Finally, this review highlights the current challenges and perspectives on future directions in this research field. By leveraging these new wood-based technologies and analysis tools for the fabrication of carbon-storage materials, it is possible to design sustainable and carbon-negative buildings, which could have a significant impact on mitigating climate change.

Turning dead leaves into an active multifunctional material as evaporator, photocatalyst, and bioplastic

Large numbers of leaves fall on the earth each autumn. The current treatments of dead leaves mainly involve completely destroying the biocomponents, which causes considerable energy consumption and environmental issues. It remains a challenge to convert waste leaves into useful materials without breaking down their biocomponents. Here, we turn red maple dead leaves into an active three-component multifunctional material by exploiting the role of whewellite biomineral for binding lignin and cellulose. Owing to its intense optical absorption spanning the full solar spectrum and the heterogeneous architecture for effective charge separation, films of this material show high performance in solar water evaporation, photocatalytic hydrogen production, and photocatalytic degradation of antibiotics. Furthermore, it also acts as a bioplastic with high mechanical strength, high-temperature tolerance, and biodegradable features. These findings pave the way for the efficient utilization of waste biomass and innovations of advanced materials.

Macroscale Fabrication of Lightweight and Strong Porous Carbon Foams through Template-Coating Pair Design

Manufacturing of low-density-high-strength carbon foams can benefit the construction, transportation, and packaging industries. One successful route to lightweight and mechanically strong carbon foams involves pyrolysis of polymeric architectures, which is inevitably accompanied by drastic volumetric shrinkage (usually >98%). As such, a challenge of these materials lies in maintaining bulk dimensions of building struts that span orders of magnitude difference in length scale from centimeters to nanometers. This work demonstrates fabrication of macroscale low-density-high-strength carbon foams that feature exceptional dimensional stability through pyrolysis of robust template-coating pairs. The template serves as the architectural blueprint and contains strength-imparting properties (e.g., high node density and small strut dimensions); it is composed of a low char-yielding porous polystyrene backbone with a high carbonization-onset temperature. The coating serves to imprint and transcribe the template architecture into pyrolytic carbon; it is composed of a high char-yielding conjugated polymer with a relatively low carbonization-onset temperature. The designed carbonization mismatch enables structural inheritance, while the decomposition mismatch affords hollow struts, minimizing density. The carbons synthesized through this new framework exhibit remarkable dimensional stability (≈80% dimension retention; ≈50% volume retention) and some of the highest specific strengths (≈0.13 GPa g^-1 cm³ ) among reported carbon foams derived from porous polymer templates.

The complex structure of Fomes fomentarius represents an architectural design for high-performance ultralightweight materials

High strength, hardness, and fracture toughness are mechanical properties that are not commonly associated with the fleshy body of a fungus. Here, we show with detailed structural, chemical, and mechanical characterization that Fomes fomentarius is an exception, and its architectural design is a source of inspiration for an emerging class of ultralightweight high-performance materials. Our findings reveal that F. fomentarius is a functionally graded material with three distinct layers that undergo multiscale hierarchical self-assembly. Mycelium is the primary component in all layers. However, in each layer, mycelium exhibits a very distinct microstructure with unique preferential orientation, aspect ratio, density, and branch length. We also show that an extracellular matrix acts as a reinforcing adhesive that differs in each layer in terms of quantity, polymeric content, and interconnectivity. These findings demonstrate how the synergistic interplay of the aforementioned features results in distinct mechanical properties for each layer.

Carbonized wood impregnated with bimetallic nanoparticles as a monolithic continuous-flow microreactor for the reduction of 4-nitrophenol

Porous monolithic microreactors show great promise in catalytic applications, but are usually based on non-renewable materials. Herein, we demonstrate a Ni/Au nanoparticle-decorated carbonized wood (Ni/Au-CW) monolithic membrane microreactor for the efficient reduction of 4-nitrophenol. The hierarchical porous wood structure supports uniformly distributed heterobimetallic Ni/Au nanoparticles. As a consequence of these two factors, both mass diffusion and electron transfer are enhanced, resulting in a superior reduction efficiency of 99.5% as the liquor flows through the optimised Ni/Au-CW membrane. The reaction mechanism was investigated by electron paramagnetic resonance spectroscopy and density functional theory calculations. The proposed attraction-repulsion mechanism facilitated by the bimetallic nanoparticles has been ascribed to the different electronegativities of Ni and Au. The Ni/Au-CW membrane exhibits excellent catalytic performance and could be applicable to other catalytic transformations.

Autonomous self-burying seed carriers for aerial seeding

Aerial seeding can quickly cover large and physically inaccessible areas¹ to improve soil quality and scavenge residual nitrogen in agriculture², and for postfire reforestation^3-5 and wildland restoration^6,7. However, it suffers from low germination rates, due to the direct exposure of unburied seeds to harsh sunlight, wind and granivorous birds, as well as undesirable air humidity and temperature^1,8,9. Here, inspired by Erodium seeds^10-14, we design and fabricate self-drilling seed carriers, turning wood veneer into highly stiff (about 4.9 GPa when dry, and about 1.3 GPa when wet) and hygromorphic bending or coiling actuators with an extremely large bending curvature (1,854 m^-1), 45 times larger than the values in the literature^15-18. Our three-tailed carrier has an 80% drilling success rate on flat land after two triggering cycles, due to the beneficial resting angle (25°-30°) of its tail anchoring, whereas the natural Erodium seed's success rate is 0%. Our carriers can carry payloads of various sizes and contents including biofertilizers and plant seeds as large as those of whitebark pine, which are about 11 mm in length and about 72 mg. We compare data from experiments and numerical simulation to elucidate the curvature transformation and actuation mechanisms to guide the design and optimization of the seed carriers. Our system will improve the effectiveness of aerial seeding to relieve agricultural and environmental stresses, and has potential applications in energy harvesting, soft robotics and sustainable buildings.

A Petrochemical-Free Route to Superelastic Hierarchical Cellulose Aerogel

Cellulose aerogels are plagued by intermolecular hydrogen bond-induced structural plasticity, otherwise rely on chemicals modification to extend service life. Here, we demonstrate a petrochemical-free strategy to fabricate superelastic cellulose aerogels by designing hierarchical structures at multi scales. Oriented channels consolidate the whole architecture. Porous walls of dehydrated cellulose derived from thermal etching not only exhibit decreased rigidity and stickiness, but also guide the microscopic deformation and mitigate localized large strain, preventing structural collapse. The aerogels show exceptional stability, including temperature-invariant elasticity, fatigue resistance (∼5 % plastic deformation after 10⁵  cycles), high angular recovery speed (1475.4° s^-1 ), outperforming most cellulose-based aerogels. This benign strategy retains the biosafety of biomass and provides an alternative filter material for health-related applications, such as face masks and air purification.

Is Wood a Material? Taking the Size Effect Seriously

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood's cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood's mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood's mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Deep eutectic solvent assisted fabrication of zirconium phytate thin nanosheets for important biomass transformations

Utilization of naturally occurring resources to construct functional catalytic materials is significantly important, and facile and environmental-benign strategies are highly desired to afford the materials having a specific structure and good catalytic activity. Herein, we reported an innovative deep eutectic solvent (DES)-assisted strategy to synthesize zirconium phytate with a thin nanosheet structure (denoted as Zr-Phy-DES) using plant-originated phytic acid (PhyA) as the renewable building block. This strategy was eco-friendly and adjustable owing to the designability of DESs. The Zr-Phy-DES as an acidic catalyst showed high activity on two important biomass transformations, i.e., dehydration of carbohydrates and Meerwein-Ponndorf-Verley reduction of ethyl levulinate. Interestingly, Zr-Phy-DES showed higher catalytic performance than the zirconium phytates prepared in ethylene glycol and N,N-dimethylformamide, confirming the advantage of DESs for preparing functional materials. Notably, the unique feature of this proposed strategy is that renewable catalysts are prepared in an environmental-benign solvent for efficiently catalyzing biomass transformation.

•

An eco-friendly strategy for preparing catalytic materials with a specific structure

•

The catalytic activity of the prepared materials varied with the type of solvents

•

The material prepared in deep eutectic solvent showed better performance

•

Catalytic materials from natural resources and green solvents to convert biomass

Wood-Derived Vascular Patches Loaded With Rapamycin Inhibit Neointimal Hyperplasia

Background: Patches are commonly used to close blood vessels after vascular surgery. Most currently used materials are either prosthetics or animal-derived; although natural materials, such as a leaf, can be used as a patch, healing of these natural materials is not optimal; rhodamine and rapamycin have been used to show that coating patches with drugs allow drug delivery to inhibit neointimal hyperplasia that may improve patch healing. Wood is abundant, and its stiffness can be reduced with processing; however, whether wood can be used as a vascular patch is not established. We hypothesized that wood can be used as a vascular patch and thus may serve as a novel plant-based biocompatible material.

Method: Male Sprague–Dawley rats (aged 6–8 weeks) were used as an inferior vena cava (IVC) patch venoplasty model. After softening, wood patches coated with rhodamine and rapamycin were implanted into the rat subcutaneous tissue, the abdominal cavity, or the IVC. Samples were explanted on day 14 for analysis.

Result: Wood patches became soft after processing. Patches showed biocompatibility after implantation into the subcutaneous tissue or the abdominal cavity. After implantation into the IVC, the patches retained mechanical strength. There was a significantly thinner neointima in wood patches coated with rapamycin than control patches (146.7 ± 15.32 μm vs. 524.7 ± 26.81 μm; p = 0.0001). There were CD34 and nestin-positive cells throughout the patch, and neointimal endothelial cells were Eph-B4 and COUP-TFII-positive. There was a significantly smaller number of PCNA and α-actin dual-positive cells in the neointima (p = 0.0003), peri-patch area (p = 0.0198), and adventitia (p = 0.0004) in wood patches coated with rapamycin than control patches. Piezo1 was expressed in the neointima and peri-patch area, and there were decreased CD68 and piezo1 dual-positive cells in wood patches coated with rapamycin compared to control patches.

Conclusion: Wood can be used as a novel biomaterial that can be implanted as a vascular patch and also serve as a scaffold for drug delivery. Plant-derived materials may be an alternative to prosthetics or animal-based materials in vascular applications.

Intercellular Matrix Infiltration Improves the Wet Strength of Delignified Wood Composites

Delignified wood (DW) represents a promising bio-based fibrous material as a reinforcing component in high-performance composites. These cellulose composites possess excellent strength and stiffness in the dry state, which are significantly higher than for natural wood. However, in the wet state, a penetrating water layer enters the intercellular regions and disrupts the stress transfer mechanisms between cell fibers in fully DW. This water layer initially facilitates complex shaping of the material but imparts DW composites with very low wet stiffness and strength. Therefore, a sufficient stress transfer in the wet state necessitates a resin impregnation of these intercellular regions, establishing bonding mechanisms between adjacent fibers. Here, we utilize a water-based dimethyloldihydroxyethylene urea thermosetting matrix (DMDHEU) and compare it with a non-water-based epoxy matrix. We infiltrate these resins into DW and investigate their spatial distribution by scanning electron microscopy, atomic force microscopy, and confocal Raman spectroscopy. The water-based resin impregnates the intercellular areas and generates an artificial compound middle lamella, while the epoxy infiltrates only the cell lumina of the dry DW. Tensile tests in the dry and wet states show that the DMDHEU matrix infiltration of the intercellular areas and the cell wall results in a higher tensile strength and stiffness compared to the epoxy resin. Here, the artificial compound middle lamella made of DMDHEU bonds adjacent fibers together and substantially increases the composites' wet strength. This study elucidates the importance of the interaction and spatial distribution of the resin system within the DW structure to improve mechanical properties, particularly in the wet state.

Progress, Challenge and Perspective of Fabricating Cellulose

Cellulose as the most abundant biopolymers on Earth, presents appealing performance in mechanical properties, thermal management, and versatile functionalization. The development of fabrication methods closely relates to enrich its functionality and reduce manufacture cost. However, cellulose is hard to be dissolved by most common solvents or melt due to its recalcitrant property. Herein, the recent progress of fabricating cellulose is summarized. First, the unique hierarchical structure of cellulose is fully investigated and the resulted processability is highlighted in directions of down to nanocellulose, dissolution, and thermoplastic processing. Then, the reported fabrication methods are summarized in three aspects: (1) self-assembly from nano/micro cellulose suspensions, especially the self-assembly of cellulose nanocrystals; (2) dissolution-regeneration-drying, covering spinning and solvent infusion processing; and (3) thermoplastic processing, focusing on analysis of the setup and the morphology changes of the prepared products. In each aspect, the flowchart of the fabrication process, the behind mechanism, fabricated products, and effects of processing parameters are explored. Finally, this review provides a perspective on the further direction of fabricating cellulose, especially the challenges toward mass production of cellulose. This article is protected by copyright. All rights reserved.

Flexible and digestible wood caused by viral-induced alteration of cell wall composition

Woody plant material represents a vast renewable resource that has the potential to produce biofuels and other bio-based products with favorable net CO₂ emissions.^1,2 Its potential has been demonstrated in a recent study that generated novel structural materials from flexible moldable wood.³ Apple rubbery wood (ARW) disease is the result of a viral infection that causes woody stems to exhibit increased flexibility.⁴ Although ARW disease is associated with the presence of an RNA virus⁵ known as apple rubbery wood virus (ARWV), how the unique symptoms develop is unknown. We demonstrate that the symptoms of ARWV infections arise from reduced lignification within the secondary cell wall of xylem fibers and result in increased wood digestibility. In contrast, the mid-lamellae region and xylem ray cells are largely unaffected by the infection. Gene expression and proteomic data from symptomatic xylem clearly show the downregulation of phenylalanine ammonia lyase (PAL), the enzyme catalyzing the first committed step in the phenylpropanoid pathway leading to lignin biosynthesis. A large increase in soluble phenolics in symptomatic xylem, including the lignin precursor phenylalanine, is also consistent with PAL downregulation. ARWV infection results in the accumulation of many host-derived virus-activated small interfering RNAs (vasiRNAs). PAL-derived vasiRNAs are among the most abundant vasiRNAs in symptomatic xylem and are likely the cause of reduced PAL activity. Apparently, the mechanism used by the virus to alter lignin exhibits similarities to the RNAi strategy used to alter lignin in genetically modified trees to generate comparable improvements in wood properties.6, 7, 8

Video abstract

•

Apple rubbery wood (ARW) symptoms are caused by decreased lignin in woody tissue

•

RNA-seq, proteomics, and metabolomics suggest phenylalanine levels decrease

•

Virus-activated small interfering RNAs (vasiRNAs) are generated in response to ARWV infection

•

VasiRNAs cause siRNA-based downregulation of phenylalanine ammonia

Single Molecular Layer of Chitin Sub-Nanometric Nanoribbons: One-Pot Self-Exfoliation and Crystalline Assembly into Robust, Sustainable, and Moldable Structural Materials

Sub-nanometric materials (SNMs) represent a series of unprecedented size-/morphology-related properties applicable in theoretical research and diverse cutting-edge applications. However, in-depth investigation and wide utilization of organic SNMs are frequently hindered, owing to the complex synthesis procedures, insufficient colloidal stability, poor processability, and high cost. In this work, a low-cost, energy-efficient, convenient, effective, and scalable method is demonstrated for directly exfoliating chitin SNMs from their natural sources through a one-pot "tandem molecular intercalation" process. The resultant solution-like sample, which exhibits ribbon-like feature and contains more than 85% of the single molecular layer (thickness <0.6 nm), is capable of being solution-processed to different types of materials. Thanks to the sub-nanometric size and rich surface functional groups, chitin SNMs reveal versatile intriguing properties that rarely observe in their nano-counterparts (nanofibrils), e.g., crystallization-like assembly in the colloidal state and alcoplasticity/self-adhesiveness in the bulk aggregate state. The finding in this work not only opens a new avenue for the high value-added utilization of chitin, but also provides a new platform for both the theoretical study and practical applications of organic SNMs.

Nanocellulose Hybrid Lignin Complex Reinforces Cellulose to Form a Strong, Water-Stable Lignin-Cellulose Composite Usable as a Plastic Replacement

The significant challenges in the use of cellulose as a replacement for plastic are its mechanical properties' degradation and uncontrolled deformation during the rewetting process. Herein, inspired by the reinforcement of cellulose by lignin in natural plant tissue, a strong and water-stable lignin-cellulose composite (LCC) was developed. A nanocellulose hybrid lignin complex (CHLC) created from bagasse residue after enzymatic hydrolysis was added into a pulp of bleached fibre extracted from pine to produce a lignin-cellulose sheet. The lignin as a water-stable reinforcing matrix, via the hydrogen bonding of the nanocellulose in the CHLC with the fibre was efficiently introduced onto the fibres and the fibre network voids. Compared with a typical lignin-free cellulose sheet, the dry strength and wet strength of the LCC were 218% and 2233% higher, respectively. The developed LCC is an eco-friendly and biodegradable alternative to plastic.

Step aside, aluminum honeycomb

[Figure: see text].