Inactivation of bacteria in seawater by low-amperage electric current

Reduction of biofilm accumulation by constant and alternating potentials in static and dynamic field experiments

The application of electric fields to conductive coatings is an environmentally friendly way to reduce biofilm formation. In particular alternating potentials (APs) have received increasing attention in recent studies. Here, an electrochemical rotating disk setup for dynamic field exposure experiments was developed to study how APs alter the attachment of fouling organisms in a multispecies ocean environment. A specific focus of the device design was proper integration of the potentiostat in the strongly corroding saltwater environment. The effect of APs on the accumulation of fouling organisms in short term field exposures was studied. Potentials on conductive gold surfaces were periodically switched between -0.3 V and 0.3 V or between -0.8 V and 0.6 V at a frequency of 0.5 Hz. APs were capable of significantly reducing the attachment of marine fouling organisms compared with the conductive samples immersed at open circuit potentials.

Control of Marine Bacteria and Diatom Biofouling by Constant and Alternating Potentials

The application of electrochemical potentials to surfaces is an easy and direct way to alter surface charge density, the structure of the electrochemical double layer, and the presence of electrochemically activated species. On such electrified interfaces the formation of biofilms is reduced. Here we investigate how applied potentials alter the colonization of surfaces by the marine bacterium Cobetia marina and the marine diatom Navicula perminuta. Different constant potentials between -0.8 and 0.6 V as well as regular switching between two potentials were investigated, and their influence on the attachment of the two biofilm-forming microorganisms on gold-coated working electrodes was quantified. Reduced bacteria and diatom attachment were found when negative potentials and alternating potentials were applied. The results are discussed on the basis of the electrochemical processes occurring at the working electrode in artificial seawater as revealed by cyclic voltammetry.

Capture and Kill: Selective Eradication of Target Bacteria by a Flexible Bacteria-Imprinted Chip

This paper reports an antibacterial chip that can selectively capture bacteria and kill them using low-voltage DC electricity. We prepared a bacteria-imprinted, flexible PDMS chip that can separate target bacteria from suspensions with high selectivity. The chip contained integrated electrodes that can kill the captured bacteria within 10 min by applying a low DC voltage. The used chip could be easily regenerated by solution immersion. Meanwhile, the PDMS chip showed good biocompatibility and inhibited adhesion of human blood cells. Our work points to a new strategy to address pathogenic bacterial contamination and infection.

The Destructive Effects of Extremely Halophilic Archaeal Strains on Sheepskins, and Proposals for Remedial Curing Processes : Use of sterile brine or direct electric current to prevent red heat damage on salted sheepskins

Proteolytic and lipolytic extremely halophilic archaea found in curing salt may contaminate skins during the brine curing process and damage skin structure. In the present study, three proteolytic and lipolytic extremely halophilic archaea were isolated from deteriorated salted sheepskins and characterised using conventional and molecular methods. Each test strain (Haloarcula salaria AT1, Halobacterium salinarum 22T6, Haloarcula tradensis 7T3), a mixed culture of these strains and the mixed culture treated with 1.5 A direct current (DC) were used for brine curing processes of fresh sheepskins and examined during 47 days of storage to evaluate the degree of destruction wreaked by these microorganisms. Both organoleptic properties and scanning electron microscopy (SEM) images of sheepskins proved that each separate test strain and the mixed culture caused serious damage. However, the mixed culture of strains treated with electric current did not damage sheepskin structure. Therefore, we highly recommend sterilisation of brine using DC to prevent archaeal damage on cured hides and skins in the leather industry.

Compact High-Voltage Pulse Generator for Pulsed Electric Field Applications: Lab-Scale Development

Square wave pulses have been identified as more lethal compared to exponential decay pulses in PEF applications. This is because of the on-time which is longer causes a formidable impact on the microorganisms in the food media. To have a reliable high-voltage pulse generator, a technique of capacitor discharge was employed. Four units of capacitor rated 100 μF 1.2 kV were connected in series to produce 25 μF 4.8 kV which were used to store the energy of approximately 200 J. The energy stored was discharged via HTS 181-01-C to the load in the range of nano to microseconds of pulse duration. The maximum voltage applied was limited to 4 kV because it is a lab-scale project. The electrical circuit diagram and the development procedure, as well as experimental results, are presented.

Effects of pre-treatment technologies on dark fermentative biohydrogen production: A review

Biohydrogen production from dark fermentation of lignocellulosic materials represents a huge potential in terms of renewable energy exploitation. However, the low hydrogen yield is currently hindering its development on industrial scale. This study reviewed various technologies that have been investigated for enhancing dark fermentative biohydrogen production. The pre-treatment technologies can be classified based on their applications as inoculum or substrates pre-treatment or they can be categorised into physical, chemical, physicochemical and biological based on the techniques used. From the different technologies reviewed, heat and acid pre-treatments are the most commonly studied technologies for both substrates and inoculum pre-treatment. Nevertheless, these two technologies need not necessarily be the most suitable since across different studies, a wide array of other emerging techniques as well as combined technologies have yielded positive findings. To date, there exists no perfect technology for either inoculum or substrate pre-treatment. Although the aim of inoculum pre-treatment is to suppress H2-consumers and enrich H2-producers, many sporulating H2-consumers survive the pre-treatment while some non-spore H2-producers are inhibited. Besides, several inoculum pre-treatment techniques are not effective in the long run and repeated pre-treatment may be required for continuous suppression of H2-consumers and sustained biohydrogen production. Furthermore, many technologies employed for substrates pre-treatment may yield inhibitory compounds that can eventually decrease biohydrogen production. Consequently, much research needs to be done to find out the best technology for both substrates and inoculum pre-treatment while also taking into consideration the energetic, economic and technical feasibility of implementing such a process on an industrial scale.

Inhibitory effect of direct electric field and HA-ZnO composites on S. aureus biofilm formation

In addressing the issue of prosthetic infection, we demonstrate herein how direct electric field (DC EF) stimulation can effectively inhibit biofilm formation, when pathogenic Staphylococcus aureus (MRSA, USA 300) are grown on HA-xZnO (x = 0, 5, 7.5, and 10 wt %) biocomposites in vitro. After bacterial preincubation for 4 h, a low intensity DC EF (1V/cm) was applied for different time periods (t = 6, 12, 18, and 24 h). The bacterial viability and biofilm maturation were evaluated by a combination of biochemical assays, fluorescence/confocal microscopy, and flow cytometry. The results confirm a time-dependent and composition-independent decrease in bacterial viability and biofilm formation on HA-xZnO composites w.r.t EF-treated HA. Flow cytometry analysis indicated that 12 h EF application resulted in membrane depolarization of ∼35% of S. aureus populations on HA-xZnO composites. The live/dead assay results revealed ∼60% decline in viable bacterial numbers with a concomitant 3.5-fold increase in the production of reactive oxygen species (ROS) after 18 h of EF. The loss in bacterial viability and biofilm instability is due to the synergistic bactericidal action of ZnO and EF. Taken together, the use of engineered biomaterial substrate with antimicrobial reinforcement coupled with continuous low intensity EF application can be adopted to treat prosthetic implant associated infection. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1064-1075, 2016.

Intervention strategies for reducing Vibrio parahaemolyticus in seafood: a review

Vibrio parahaeomolyticus, a natural inhabitant in estuarine marine water, has been frequently isolated from seafood. It has been recognized as the leading causative agent for seafoodborne illness all over the world. Numerous physical, chemical, and biological intervention methods for reducing V. parahaeomolyticus in seafood products have been investigated and practiced. Each intervention method has distinct advantages and disadvantages depending on the processing needs and consumer preference. This review provides a comprehensive overview of various intervention strategies for reducing V. parahaeomolyticus in seafood with an emphasis on the efficiency of bacterial inactivation treatments and the changes in sensory qualities of seafood. In the meantime, reported researches on alternative technologies which have shown effectiveness to inactivate V. parahaemolyticus in seawater and other food products, but not directly in seafood are also included. The successful applications of appropriate intervention strategies could effectively reduce or eliminate the contamination of V. parahaeomolyticus in seafood, and consequently contribute to the improvement of seafood safety and the reduction of public health risk.

Application of an electric field for pretreatment of a seeding source for dark fermentative hydrogen production

In present study, an electric field was newly adopted as a pretreatment method for inoculum preparation in dark fermentative hydrogen production. Various voltages (5-20 V for 10 min) were applied, and the feasibility and efficiency of this method were compared with those of heat pretreatment (90°C for 20 min). Both the highest H2 yield, 1.43 mol H2/mol hexoseadded, and the highest production rate, 101.4 mL H2/L/h, were observed at 10 V. While RNA concentration of above 100mg/L was maintained up to 10 V, it was decreased at an applied voltage of 20 V, where the worst performance was observed. Microbial analysis results confirmed that only H2 producing bacteria were detected with electric pretreatment, while non-H2 producing bacteria coexist with heat and electric (5 V) pretreatment. The results suggested that application of an electric field has reasonable potential as an alternative method for preparing inoculums for hydrogen production.

Electroporation enhances the ability of lactobacilli to remove cholesterol

The objective of the present study was to evaluate the effect of electroporation on the membrane properties of lactobacilli and their ability to remove cholesterol in vitro. The growth of lactobacilli cells treated at 7.5 kV/cm for 4 ms was increased by 0.89 to 1.96 log(10) cfu/mL upon fermentation at 37 °C for 20 h, the increase being attributed to the reversible and transient formation of pores and defragmentation of clumped cells. In addition, an increase of cholesterol assimilation as high as 127.2% was observed for most cells electroporated at a field strength of 7.5 kV/cm for 3.5 ms compared with a lower field strength of 2.5 kV/cm. Electroporation also increased the incorporation of cholesterol into the cellular membrane, as shown by an increased cholesterol:phospholipids ratio (50.0-59.6%) upon treatment at 7.5 kV/cm compared with treatment at 2.5 kV/cm. Saturation of cholesterol was observed in different regions of the membrane bilayer such as upper phospholipids, apolar tail, and polar heads, as indicated by fluorescence anisotropy using 3 fluorescent probes. Electroporation could be a useful technique to increase the ability of lactobacilli to remove cholesterol for possible use as cholesterol-lowering adjuncts in the future.

Biological characterization of two marine Bdellovibrio-and-like organisms isolated from Daya bay of Shenzhen, China and their application in the elimination of Vibrio parahaemolyticus in oyster

Bdellovibrio-and-like organisms (BALOs) are a group of highly motile delta-proteobacteria that prey on other gram-negative bacteria. However, nothing is known of the application potential of marine BALOs in safeguarding seafood safety. Here, biological characterization of two marine BALOs strains and their application in the elimination of Vibrio parahaemolyticus in oyster (Crassostrea ariakensis) at the laboratory scale were investigated. BALOs strains BDH12 and BDHSH06 were isolated from sediment of Daya bay in Shenzhen of China, with Shewanella putrefaciens strain 12 and V. parahaemolyticus strain SH06 as preys, respectively, when using double layer agar technique. They were identified as BALOs morphologically by transmission electron microscopy, while partial 16S rDNA sequencing analysis revealed that they showed no close relationships with members of the known genera Bdellovibrio, Bacteriolyticum, Bacteriovorax, or Peredibacter. Biological characterizations revealed that both strains had the optimal pH, salinity and temperature at 7.2, 3% and 30 °C, correspondingly. They could not utilize autoclaved, dead cells as hosts. Prey range analysis revealed that individually, BDH12 and BDHSH06 lysed 82.5% (47 strains) and 84.2% (48 strains) of the total 57 preys tested respectively. In combination, they lysed 98.2% (56 of 57) strains. All strains of V. parahaemolyticus, Vibrio cholerae and Vibrio alginolyticus tested could be lysed by both strains. A 7-day laboratory-scale V. parahaemolyticus elimination experiment in oyster showed that in the control, the cell counts of total vibrios and V. parahaemolyticus strain Vp plus in water and in oyster intestines were on the rise, whereas in the BALOs treated groups, their numbers were down from 8.09±0.05 log CFU/ml and 8.02±0.04 log CFU/ml to 2.39±0.01 log CFU/ml and 2.33±0.01 log CFU/ml, respectively. The same patterns could also be observed in oyster intestines. Results of this study indicate the feasibility of using BALOs to biologically control or even eliminate V. parahaemolyticus in seafood oyster.

A thin layer electrochemical cell for disinfection of water contaminated with Staphylococcus aureus

A thin layer electrochemical cell was tested and developed for disinfection treatment of water artificially contaminated with Staphylococcus aureus. Electrolysis was performed with a low-voltage DC power source applying current densities of 75 mA cm(-2) (3 A) or 25 mA cm(-2) (1 A). A dimensionally stable anode (DSA) of titanium coated with an oxide layer of 70%TiO2 plus 30%RuO2 (w/w) and a 3 mm from a stainless-steel 304 cathode was used in the thin layer cell. The experiments were carried out using a bacteria suspension containing 0.08 M sodium sulphate with chloride-free to determine the bacterial inactivation efficacy of the thin layer cell without the generation of chlorine. The chlorine can promote the formation of trihalomethanes (THM) that are carcinogenic. S. aureus inactivation increased with electrolysis time and lower flow rate. The flow rates used were 200 or 500 L h(-1). At 500 L h(-1) and 75 mA cm(-2) the inactivation after 60 min was about three logs of decreasing for colony forming units by mL. However, 100% inactivation for S. aureus was observed at 5.6 V and 75 mA cm(-2) after 30 min. Thus, significant disinfection levels can be achieved without adding oxidant substances or generation of chlorine in the water.

Non-disruptive release of Pseudomonas putida proteins by in situ electric breakdown of intact cells

Analysis of the native proteome of bacterial cells typically involves physical procedures (sonication, French press) and/or biochemical methods (treatment with lysozyme, osmotic shock etc.) to break open the bacteria to yield a soluble protein fraction. Such procedures are not only time consuming, but they change bacterial physiology during manipulation and affect labile post-translational modifications such as His-P bonds. In this work, we document the efficacy of the dielectric breakdown of live bacteria for releasing and delivering the protein contents of intact cells directly into a non-denaturing gel system. By means of such an in situ electrophoresis, the protein pool enters the separation medium without any manipulation of the cells other than being exposed to a moderate electric voltage. To validate the method we have followed the fate of the two forms of the PtsN (EIIA(Ntr)) protein of the phosphoenolpyruvate:carbohydrate phosphotransferase system (PTS) of Pseudomonas putida through the various stages of the procedure. Apart of detecting the corresponding polypeptides, we show that this procedure releases the bulk of the proteome while keeping unharmed the phosphorylation state of EIIA(Ntr) as it was present in the cells prior to applying the electric field. The method is applicable to other bacteria as well.

Involvement of radical species in inactivation of Vibrio parahaemolyticus in saline solutions by direct-current electric treatment

The effect of pulsed low-direct-current (DC) electric treatment on the viability of Vibrio parahaemolyticus in artificial seawater and 3.0% (w/v) NaCl solution was studied as a function of available chlorine (AC) concentration. The amount of AC generated during the DC electric treatment increased in proportion to the amount of passed DC. The survival fraction of V. parahaemolyticus cells decreased depending on AC concentration. When the generated AC components were completely reduced in the presence of sufficient sodium thiosulfate, no inactivation of V. parahaemolyticus in the NaCl solution was observed during the DC electric treatment. Based on the AC concentration, the inactivation efficacies of the DC electric treatment of the seawater and NaCl solution were approximately 4-fold and 30-fold that of the exogenous addition of sodium hypochlorite, respectively. Fluorometric analysis using 2-[6-(4'-hydroxy)phenoxy-3H-xanthen-3-on-9-yl]benzoic acid showed that the generation of highly reactive radical species such as hydroxyl radical in the seawater and NaCl solution occurred during the DC electric treatment. The amount of generated radical species depended on the amount of passed DC. It is concluded that pulsed low-DC electric treatment of saline solutions exerts superior inactivation efficacy against V. parahaemolyticus to sodium hypochlorite owing to the generation of radical species.

Inactivation of Vibrio parahaemolyticus in effluent seawater by alternating-current treatment

Vibrio parahaemolyticus, the cause of gastroenteritis in humans, was inactivated by alternating low-amperage electricity. In this study, the application of alternating low-amperage electric treatment to effluent seawater was investigated for the large-scale disinfection of seawater. This method was able to overcome the problem of chlorine generation that results from treatment with continuous direct current. In conclusion, our results showed that alternating-current treatment inactivates V. parahaemolyticus in effluent seawater while minimizing the generation of chlorine and that this alternating-current treatment is therefore suitable for practical industrial applications.