A Novel Polymer Inclusion Membrane-Based Green Optical Sensor for Selective Determination of Iron: Design, Characterization, and Analytical Applications

The design, characterization, and analytical application of a green optical sensor for the selective determination of Fe(II) ions is proposed. The sensor is based on the immobilization of the chromogenic reagent picolinaldehyde salicyloylhydrazone (SHPA) within a polymer inclusion membrane. To reduce solvent usage, the reagent was synthesized using a green mechanochemical procedure. The components for sensor preparation were optimized with a sequential simplex method and the optimal composition was found to be 0.59 g cellulose triacetate (base polymer), 0.04 g SHPA (chemosensor reagent), 4.9 mL dibutyl phthalate (plasticizer), and 38 mL dichloromethane (solvent). The conditions of iron analysis were also optimized resulting in pH 6 for aqueous solution, 90 min exposure time and 10 min short-term stability. The optical sensor showed a linear range from the limit of detection (0.48 µmol L-1) to 54 µmol L-1 Fe(II). The precision of the method was found to be 1.44% and 1.19% for 17.9 and 45 µmol L-1 Fe(II), respectively. The characteristics of the sensor allowed the design of a Fe(II)/Fe(III) speciation scheme. The methodology was successfully applied to the determination of iron in food preservatives, food additives, and dietary supplement. Additionally, the Fe speciation scheme was successfully applied to an agricultural fertilizer.

Construction of an optical sensor for copper determination in environmental, food, and biological samples based on the covalently immobilized 2-(2-benzothiazolylazo)-3-hydroxyphenol in agarose

An optical chemical sensor has been developed for the quantitative spectrophotometric analysis of copper. The optode is dependent on covalent immobilization of 2-(2-benzothiazolylazo)-3-hydroxyphenol (BTAHP) in a transparent agarose membrane. The absorbance variation of immobilized BTAHP on agarose as a film upon the addition of 5 × 10-3 M aqueous solutions of Mn2+, Zn2+, Hg2+, Cd2+, Pb2+, Co2+, Ni2+, Fe2+, La3+, Fe3+, Cr3+, Zr4+, Se4+, Th4+, and UO22+ revealed substantially higher changes in the Cu2+ ion content compared to other ions investigated here. The effects of various experimental parameters, such as the solution pH, the reaction time, and the concentration of reagents, on the quality of Cu2+ sensing were examined. Under ideal experimental circumstances, a linear response was achieved for Cu2+ concentrations ranging from 1.0 × 10-9 to 7.5 × 10-6 M with an R2 value of 0.9988. The detection (3σ) and quantification (10σ) limits of the procedure for Cu2+ analyses were 3.0 × 10-10 and 9.8 × 10-10 M, respectively. No observable interference was recorded in the detection of Cu2+ due to other inorganic cations. With no indication of BTAHP leaching, the membrane demonstrated good durability and quick response times. The optode was effectively used to determine the presence of Cu2+ in environmental water, food, and biological samples.

Sensing Cd(II) Using a Disposable Optical Sensor Based on a Schiff Base Immobilisation on a Polymer-Inclusion Membrane. Applications in Water and Art Paint Samples

A disposable colour-changeable optical sensor based on an interesting polymer inclusion-membrane (PIM) was designed to determine Cd(II) ions in aqueous medium. The Schiff base 2-acetylpyridine benzoylhydrazone (2-APBH) immobilised on the polymer membrane was used as a sensing molecule. The amounts of the PIM components were optimised by a 3² fractional factorial design with two central points and two blocks. The best optical sensor composition consisted of 2.5 g of poly(vinylchloride) (PVC) as a base polymer, 3 mL of tributyl phosphate (TBP) as a plasticiser, and 0.02 g of 2-APBH as a reagent. The sensor showed a good linear response in the range from 0.02 mg L⁻¹ (limit of detection) to 1 mg L⁻¹ of Cd(II) under the following experimental conditions: pH 9.5 (adjusted using ammonium chloride buffer solution at 0.337 mol L⁻¹), 60 min of exposure time plus 2 min of sonication (pulses at 2 s intervals), and 10 min of short-term stability. The relative standard deviation of the method was determined to be 4.04% for 0.4 mg L⁻¹ of Cd(II). The optical sensor was successfully applied to the determination of Cd(II) in natural-water and art-paint samples.

Design and optimization of a single-use optical sensor based on a polymer inclusion membrane for zinc determination in drinks, food supplement and foot health care products

A single-use optical sensor was designed for Zn(II) determination based on the immobilisation of the colorimetric reagent 2-acetylpyridine benzoylhydrazone (2-APBH) in a polymer inclusion membrane (PIM) adhered on the surface of an inert rectangular strip of polyester (Mylar). Different components for the membrane preparation were tested and those resulting in membrane with good appearance, proper physical and optical properties and ease of preparation were selected. Factorial design 23 with three replicates of the central point was applied for the optimisation of the membrane composition. The optimal composition consisted of 2.5 g of poly(vinyl chloride) (PVC), 4 mL of tributyl phosphate (TBP) and 0.04 g of 2-APBH. The optode showed a linear dynamic range from 0.03 (detection limit) to 1 mg L-1 of Zn(II) ions with a response time of 30 min in aqueous solution at pH 6 and a relative standard deviation of 3.90% for 0.4 mg L-1 of Zn(II). The sensor exhibited good selectivity to Zn(II) over other commonly ions. It was successfully applied to the determination of Zn(II) in a water certified reference material, spiked tap water, vitamin-mineral drink, food supplement and foot health care products, as contribution to the concern about this heavy metal due to its significant role in many biological and physiological processes although toxicant at high doses.

Solid phase-enhanced photothermal lensing with mesoporous polymethacrylate matrices for optical-sensing chemical analysis

Procedures for the photothermal lens determination of metals and organic compounds, on the basis of solid-phase mesoporous optical-sensing materials (polymethacrylate [PMA]) matrices with immobilized reagents, were developed. These procedures combine (i) selective and efficient preconcentration of trace substances to be analyzed in specially designed and synthesized transparent mesoporous PMA plates; (ii) sensitive determination with the reliable and traceable photometric reactions previously developed for classical spectrophotometry; and (iii) the sensitivity enhancement of photothermal lens detection in polymers, which provides at least a ten-fold increase in sensitivity compared with solutions due to polymer thermo-optical properties (solid phase-enhanced thermal lensing). It is shown that the overall sensitivity of photothermal lens measurements in PMA matrices is two orders higher than photometric absorbance measurements for the same excitation source power, which is in good agreement with the expected theoretical sensitivity. Changes in the preparation of transparent PMA plates and analytical procedures for photothermal measurements compared with spectrophotometry are discussed. PMA matrices modified with various analytical reagents were applied to trace determination of Hg(II), Fe(II), Ag(I), Cu(II), and ascorbic acid, with subnanomolar to nanomolar limits of detection.