Effect of H2O2 @CuONPs in the UV Light-Induced Removal of Organic Pollutant Congo Red Dye: Investigation into Mechanism with Additional Biomedical Study

Hazardous dyes in industrial wastewater are an internationally recognized issue for community health. Nanoparticles synthesized through green protocols are a fascinating research field with numerous applications. The current study mainly aimed to investigate the degradation of Congo red (CR) dye under UV light in the presence of H2O2 and the photocatalytic activity of copper oxide nanoparticles (CuONPs). For CuONP formation, Citrus maxima extract contains a high number of phytochemical constituents. The size of CuONPs ranges between 25 and 90 nm. The photocatalytic activity of CuONPs with the addition of H2O2 was observed and analyzed under UV light to eliminate CR dye. The UV light caused the decomposition of H2O2, which produced ·OH radicals. The results revealed a significant increment in dye degradation during the presence of H2O2. The effect of concentration on the degradation of the CR dye was also studied. The degradation pathway of organic pollutants was reputable from the hydroxy radical medicated degradation of CR. Advanced Oxidation Treatment depends on the in situ production of reactive ·OH species and is presented as the most effective procedure for decontamination. The biological activity of CuONPs was evaluated against Escherichia coli Bacillus subtillis, Staphylococcus aureus, Shigella flexenari, Acinetobacter Klebsiella pneumonia, Salmonella typhi and Micrococcus luteus. The newly synthesised nanomaterials showed strong inhibition activity against Escherichia coli (45%), Bacillus subtilis (42%) and Acinetobacter species (25%). The activity of CuONPs was also investigated against different fungus species such as: Aspergillus flavus, A. niger, Candida glabrata, T. longifusus, M. Canis, C. glabrata and showed a good inhibition zone against Candida glabrata 75%, Aspergillus flavus 68%, T. longifusus 60%. The materials showed good activity against C. glaberata, A. flavus and T. longifusus. Furthermore, CuONPs were tested for antioxidant properties using 2, 2 diphenyl-1-picrylhydrazyl) (DPPH).

Engineered magnetic oxides nanoparticles as efficient sorbents for wastewater remediation: a review

The rapid urbanization and industrialization is causing worldwide water pollution, calling for advanced cleaning methods. For instance, pollutant adsorption on magnetic oxides is efficient and very practical due to the easy separation from solutions by an magnetic field. Here we review the synthesis and performance of magnetic oxides such as iron oxides, spinel ferrites, and perovskite oxides for water remediation. We present structural, optical, and magnetic properties. Magnetic oxides are also promising photocatalysts for the degradation of organic pollutants. Antimicrobial activities and adsorption of heavy metals and radionucleides are also discussed.

Removal of Organic Dyes from Water and Wastewater Using Magnetic Ferrite-Based Titanium Oxide and Zinc Oxide Nanocomposites: A Review

Heterogeneous photocatalysis using titanium dioxide (TiO2) and zinc oxide (ZnO) has been widely studied in various applications, including organic pollutant remediation in aqueous systems. The popularity of these materials is based on their high photocatalytic activity, strong photosensitivity, and relatively low cost. However, their commercial application has been limited by their wide bandgaps, inability to absorb visible light, fast electron/hole recombination, and limited recyclability since the nanomaterial is difficult to recover. Researchers have developed several strategies to overcome these limitations. Chief amongst these is the coupling of different semi-conductor materials to produce heterojunction nanocomposite materials, which are both visible-light-active and easily recoverable. This review focuses on the advances made in the development of magnetic ferrite-based titanium oxide and zinc oxide nanocomposites. The physical and magnetic properties of the most widely used ferrite compounds are discussed. The spinel structured material had superior catalytic and magnetic performance when coupled to TiO2 and ZnO. An assessment of the range of synthesis methods is also presented. A comprehensive review of the photocatalytic degradation of various priority organic pollutants using the ferrite-based nanocomposites revealed that degradation efficiency and magnetic recovery potential are dependent on factors such as the chemical composition of the heterojunction material, synthesis method, irradiation source, and structure of pollutant. It should be noted that very few studies have gone beyond the degradation efficiency studies. Very little information is available on the extent of mineralization and the subsequent formation of intermediate compounds when these composite catalysts are used. Additionally, potential degradation mechanisms have not been adequately reported.

Recent Advances in Synthesis and Applications of MFe2O4 (M = Co, Cu, Mn, Ni, Zn) Nanoparticles

In the last decade, research on the synthesis and characterization of nanosized ferrites has highly increased and a wide range of new applications for these materials have been identified. The ability to tailor the structure, chemical, optical, magnetic, and electrical properties of ferrites by selecting the synthesis parameters further enhanced their widespread use. The paper reviews the synthesis methods and applications of MFe₂O₄ (M = Co, Cu, Mn, Ni, Zn) nanoparticles, with emphasis on the advantages and disadvantages of each synthesis route and main applications. Along with the conventional methods like sol-gel, thermal decomposition, combustion, co-precipitation, hydrothermal, and solid-state synthesis, several unconventional methods, like sonochemical, microwave assisted combustion, spray pyrolysis, spray drying, laser pyrolysis, microemulsion, reverse micelle, and biosynthesis, are also presented. MFe₂O₄ (M = Co, Cu, Mn, Ni, Zn) nanosized ferrites present good magnetic (high coercivity, high anisotropy, high Curie temperature, moderate saturation magnetization), electrical (high electrical resistance, low eddy current losses), mechanical (significant mechanical hardness), and chemical (chemical stability, rich redox chemistry) properties that make them suitable for potential applications in the field of magnetic and dielectric materials, photoluminescence, catalysis, photocatalysis, water decontamination, pigments, corrosion protection, sensors, antimicrobial agents, and biomedicine.

Exploring the influence of varying pH on structural, electro-optical, magnetic and photo-Fenton properties of mesoporous ZnFe2O4 nanocrystals

An economically viable and superficial technique was indorsed to yield ZnFe₂O₄ nanocrystals in the system to investigate the impact of pH variation on the optical, structural, electrical, and magnetic properties of as-prepared nanocrystals. The as-synthesized ZnFe₂O₄ nanocrystals were premeditated with the application protracted to degradation of Methylene blue organic dye. The results specify that the pH plays the utmost decisive facet in photo-Fenton recital. From XRD (X-Ray diffraction) analyses, it was confirmed that as-synthesized nanocrystals belong to a cubic Fd3m crystal phase. The crystallite size was also determined by the Scherrer formula and it was noticed that as the pH rises the crystallite size also increased. FT-IR (Fourier Transform Infrared) analysis depicts two absorption peaks ∼ 500 and ∼600 cm^-1 that represents tetrahedral (Td) and octahedral (Oh) sites. Using TEM (Transmission Electron Microscopy), the morphology was observed to be spherical particles with some agglomeration. Photoluminescence and UV-visible spectral studies were performed to investigate the optical properties. The bandgap energy was seen to decrease as the pH increased. Using BET analysis, the surface area for the as-synthesized samples was found to decrease on increasing the pH. The reaction results showed that the ZnFe₂O₄ has good photocatalytic activity, which can be attributed to high surface area and pore volume, and large pore size. The ZnFe₂O₄ produced by the co-precipitation route exhibited promising photocatalytic activity for the removal of textile dye, reaching nearly 99.2% of decolorization at 100 min. Therefore, ZnFe₂O₄ particles rapidly prepared by the co-precipitation route have the potential for use in treatment of textile wastewater by the heterogeneous photo-Fenton process. With the help of VSM analysis, the coercivity and other magnetic properties were determined for the as-synthesized nanocrystal with plays a significant role in photocatalytic recyclability, which intends to premediate that the prepared nanocrystals can be used in industrial persistence.

Kinetic and thermodynamic studies for evaluation of adsorption capacity of fungal dead biomass for direct dye

This study focuses on evaluation of degradation aptitude of white rot fungus (Coriolus versicolor) against Indosol Turquoise FBL dye. The outcome of numerous parameters including pH, temperature, carbon sources, nitrogen sources, C/N ratio and effect of dye concentration were studied. Maximum decolorization (99.896%) of Indosol Turquoise FBL was obtained by C. versicolor under optimized conditions. After three days, the maximum dye degradation (98%) was observed at pH 4 and 30 °C. Six carbon sources fructose, glucose, maltose, sucrose, rice bran and wheat bran were used and 96.66% degradation was observed by maltose at its optimum growth concentration (0.1 g/100 mL). Various nitrogen sources were employed for decolorization but ammonium nitrate decolorized dye up to 98.05%. The activity of three different enzymes laccase, Lignin peroxidase (LiP) and Manganese peroxidase (MnP) were calculated. The dead biomass of White rot fungus (WRF) was used for biosorption experiments. Maximum q (36 mg/g) was obtained at pH 2, at 30 °C using 0.05 g biosorbent. An increase in the q value was observed with increase in dye concentration. Freundlich adsorption isotherm and pseudo second order kinetics were followed by the data. It can be concluded that C. versicolor could be an efficient source for degradation of dyes from industrial effluents.

Micro-emulsion synthesis of La1 − xCrxFeO3 nanoparticles: effect of Cr doping on ferroelectric, dielectric and photocatalytic properties

In the present study, La1 − xCrxFeO3 (x = 0.0, 0.3, 0.6, 0.9, 1.0) was synthesized by micro-emulsion route and characterized by X-ray Diffraction (XRD), Fourier Transform Infrared (FTIR), Scanning electron microscope (SEM), Energy-dispersive X-ray (EDX) techniques. The dielectric, ferroelectric and photocatalytic properties were investigated and compared with un-doped material. The XRD analysis revealed orthorhombic geometry of La1 − xCrxFeO3 (x = 0.0, 0.3, 0.6, 0.9, 1.0), Cr was doped successfully into the lattice structure of LaFeO3 and particles were spherical and in agglomerated form. The grain sizes were recorded to be 15, 16.9, 17.1, 17.65 and 18.3 (nm) for La1 − xCrxFeO3 (x = 0.0, 0.3, 0.6, 0.9, 1.0), respectively. EDX analysis confirmed the purity of LaCrFeO3 samples. The lattice parameters, bulk density, X-ray density, crystalline size and porosity were determined were also determined of all the La1 − xCrxFeO3 samples. The dielectric constant and dielectric loss values decreased at higher frequency and Cr concentration affected the dielectric properties. The photocatalytic activity (PCA) was evaluated by degrading Congo Red (CR) dye under solar light irradiation and up to 85.43% dye degradation was achieved within 45 min of irradiation. Phyto-toxicity analysis before and after dye degradation was performed, which revealed the toxicity reduction in response of dye degradation. Results revealed that lanthanum ferrite (perovskite) doping with Cr could possibly be employed to enhance the ferroelectric, dielectric and photocatalytic properties.

A study on the spectral, microstructural, and magnetic properties of Eu-Nd double-substituted Ba0.5Sr0.5Fe12O19 hexaferrites synthesized by an ultrasonic-assisted approach

In this study, an examination on the spectral, microstructural, and magnetic characteristics of Eu-Nd double-substituted Ba_0.5Sr_0.5Fe₁₂O₁₉ hexaferrites (Ba_0.5Sr_0.5Nd_xEu_xFe_12-2xO₁₉ (x = 0.00-0.05) HFs) fabricated by an ultrasonic-assisted approach has been presented. An UZ SONOPULS HD 2070 ultrasonic homogenizer with frequency of 20 kHz and power of 70 W was used. The chemical bonding, structure and the morphology of the products were evaluated by Fourier-Transform Infrared (FT-IR) Spectroscopy, XRD (X-ray diffraction), scanning and transmission electron microscopy and techniques. The textural properties of the prepared nanomaterials were examined by using the Brunauer-Emmett-Teller (BET) method. The magnetic properties were studied using a vibrating sample magnetometer (VSM) at room temperature (RT) and low temperature 10 K. The magnitudes of various magnetic parameters including M_s (saturation magnetization), M_r (remanence) and H_c (coercivity) were estimated and evaluated. The M-H loops revealed the hard ferrimagnetic nature for all products at both temperatures. The M_s and M_r values showed a decreasing tendency with increasing degree of Eu³⁺ and Nd³⁺ substitutions whereas H_c values displayed an increasing trend. At RT, M_s, M_r and H_c values lie in the ranges of 63.0-68.8 emu·g^-1, 24.6-39.2 emu·g^-1 and 2252.4-2782.1 Oe, respectively. At 10 K, the values of M_s, M_r and H_c lie between 87.5-97.1 emu·g^-1, 33.5-40.1 emu·g^-1 and 2060.6-2417.2 Oe, respectively. The observed magnetic properties make the prepared products promising candidates to be applied in the recording media.

Ni0.4Cu0.2Zn0.4TbxFe2-xO4 nanospinel ferrites: Ultrasonic synthesis and physical properties

The Fe³⁺ ions were replace with Tb³⁺ ions as highly paramagnetic rare earth element within the structure of Ni_0.4Cu_0.2Zn_0.4Fe₂O₄ nano-spinel ferrites (NSFs). The structural, magnetic, spectroscopic and optic properties have been studied in details. All products have been synthesized via ultrasonic approach via Qsonica ultrasonic homogenizer, frequency: 20 kHz and power: 70 W for 60 min. No annealing or calcination process was applied for any product. The microstructural analysis of products has been done via X-ray powder diffractometry (XRD) which presented the cubic spinel structure with nanosized distribution of all. The cubic morphology of all products were confirmed by both HR-TEM and FE-SEM. Optical band gap (E_g) values were assessed by applying %DR (percent diffuse reflectance) analysis and Kubelka-Munk theory. The Tauc schemes showed that E_g values are in a narrow range (1.87-1.98 eV). The quadrupole splitting, line width, hyperfine magnetic field, isomer shift values and cation distribution have been determined from ⁵⁷Fe Mossbauer analysis. The magnetic properties of various nanoparticles have been obtained from VSM (vibration sample magnetometer) measurements at 10 and 300 K (RT). The magnetic results revealed superparamagnetic and soft ferromagnetic traits at 10 and 300 K, respectively. M_s (saturation magnetization) and M_r (remanence) initially increase with increasing Tb³⁺ substituting level up to x = 0.06 then diminish for further x values. H_c (coercivity) shows an opposite variation tendency of M_s and M_r. The observed magnetic traits are deeply discussed in relation with the structure, morphology, magnetic moments and cation distributions.

Comparative Studies of Magneto-Optical and Photocatalytic Properties of Magnetically Recyclable Spinel ZnFe2O4 Nanostructures by Combustion Methods

Spinel ZnFe2O4 nanoparticles (NPs) were successfully synthesized by a simple microwave irradiation method (MIM) using glycine as the fuel. For the comparative study purpose, it was also prepared by conventional heating (CHM) method. Powder X-ray diffraction (XRD), Fourier transform infrared (FT-IR), high resolution scanning electron microscope (HR-SEM), high resolution transmission electron microscope (HR-TEM), energy dispersive X-ray (EDX) spectra, selected area electron diffraction (SAED) analysis showed that the samples were pure phase spinel ZnFe2O4 nanoparticles-like morphology without any other secondary phase impurity. UV-Visible diffuse reflectance spectra (DRS) and room temperature photoluminescence (PL) spectra were confirmed the optical bandgap ([Formula: see text] and defects state of the samples. The calculated [Formula: see text] values of the samples are 1.91[Formula: see text]eV and 2.08[Formula: see text]eV for ZnFe2O4-MIM and ZnFe2O4-CHM, respectively. Vibrating sample magnetometer (VSM) analysis show the Ms value is 37.66[Formula: see text]emu/g for ZnFe2O4-MIM, which is higher than ZnFe2O4-CHM (24.23 emu/g) sample, which confirm both the products showed superparamagnetic behavior. ZnFe2O4-MIM was found to have higher surface area than ZnFe2O4-CHM, which in turn leads to the improved performance toward the photocatalytic degradation (PCD) of 4-chlorophenol (4-CP) and it was found that the sample ZnFe2O4-MIM show higher PCD efficiency (91.43%) than ZnFe2O4-CHM (84.65%), also the samples show high activity, good reusability, remarkable stability and environmentally friendly materials for industrial and technological applications.