Friction of Laser-Textured Zirconia Coated with a Platelet-Rich Fibrin

In the present in vitro study, we evaluated the adhesion of an injectable platelet-rich fibrin (i-PRF) to laser-textured zirconia surfaces and their resultant friction behavior against bone tissue. Three types of zirconia surfaces were compared regarding the i-PRF coating effects: 1) grit blasted with 250-μm spherical alumina particles and acid etched with 20% hydrofluoric acid (ZLA), 2) laser textured with a random (RD) surface pattern, or 3) laser textured with a designed pattern based on 16 lines and 8 passages (L16N8). The coefficient of friction (COF) of the specimens was assessed on a reciprocating sliding pin-on-plate tribometer at 1-N normal load, 1 Hz, and a 2-mm stroke length. Sliding wear tests were carried out against bovine femoral bone tissue in 0.9% sodium chloride solution at room temperature. Surfaces were then assessed by scanning electron microscopy. COF mean values for test groups (0.35, ZLA; 0.45, L16N8) were lower when compared with the control groups (0.52, ZLA; 0.60, L16N8), with the exception of the RD group (0.47, test; 0.43, control). Results did not show significant differences in COF mean values between RD and L16N8 surfaces after coating with i-PRF. The 3-dimensional fibrin network embedded with leukocytes, platelets, and red blood cells was responsible for decreasing COF mean values over the zirconia surfaces, thus providing a lubricant effect. Also, the morphologic aspects of the laser-treated zirconia surfaces increased the adhesion of the platelet-rich fibrin, which could speed up the osseointegration process of zirconia implants.

Effects of Streptococcus mutans and their metabolites on the wear behavior of dental restorative materials

The wear behavior of dental restorative materials is highly related to the biolubricating medium in the oral environment. Bacteria, along with their metabolic products, are essential substances in the oral cavity and have not been studied as a potential factor affecting lubrication performance during mastication. In this study, the effects of the Streptococcus mutans bacterial cells and their metabolites were investigated on the wear behavior of resin composites, polymer-infiltrated ceramic networks and zirconium-lithium silicate glass-ceramics. A reciprocating friction test and quantitative analysis of the wear morphology were utilized to determine the coefficient of friction (COF) and wear resistance of the test materials. The results showed that the bacterial metabolite medium significantly reduces the COF and wear rate of the three restorative materials and provide better protection against superficial abrasion. When tested under lactic acid medium, a key acid production in bacterial metabolites, similar wear reduction results were observed in the three materials, which confirmed that lactic acid should be accountable for the excellent lubricating property of bacterial metabolites. Furthermore, the resin composite with lower wettability exhibited a more significant wear reduction than the other two materials when lubricating with a bacterial metabolite medium. These findings provide novel insights into the biological basis of lubrication mechanisms in the oral cavity under high-loading and low-velocity conditions.

Contemporary Sterilization Protocols of Healing Abutments for Reusability: A Systematic Review

INTRODUCTION

Although healing abutments are designated for single use by most implant manufacturers, it is common practice for clinicians to reuse healing abutments. However, there is a lack of adequate references that describe detailed sterilization protocols for reuse of healing abutments.

OBJECTIVES

The purpose of this systematic review was to compile, organize, and describe the most common techniques for the sterilization of healing abutments and their efficiency in eliminating traces of microorganisms.

METHODS

An electronic search in 5 different databases was performed, including the National Library of Medicine (MEDLINE via PubMed), Embase, Cochrane Central Register of Controlled Trials, Web of Science, and Google Scholar from January 2000 to December 2020. Search variables included were dental implant, healing abutment, contaminate, contamination, reuse, and sterilization. Studies reporting with a minimum sample size of 10 healing abutments (5 per group) published in the English language were evaluated. Risk of bias assessment was elaborated for included investigations.

RESULTS

In total, 812 articles were identified, of which 8 were included in the analysis. Steam autoclave was the most widely used form of resterilization. Not a single protocol, however, was able to achieve 100% virgin surface of the healing abutments.

CONCLUSION

Although reuse of dental implant healing abutments is a cost-effective measure in dental practice, thorough surface decontamination followed by resterilization is highly recommended before reuse.

KNOWLEDGE TRANSFER STATEMENT

With consideration of cost and patient preference, results of this review would be useful in knowing various sterilization protocols for reusing healing abutments that could lead to more appropriate therapeutic decisions.

Graphene Nanocoating: High Quality and Stability upon Several Stressors

Titanium implants present 2 major drawbacks-namely, the long time needed for osseointegration and the lack of inherent antimicrobial properties. Surface modifications and coatings to improve biomaterials can lose their integrity and biological potential when exposed to stressful microenvironments. Graphene nanocoating (GN) can be deposited onto actual-size dental and orthopedic implants. It has antiadhesive properties and can enhance bone formation in vivo. However, its ability to maintain structural integrity and quality when challenged by biologically relevant stresses remains largely unknown. GN was produced by chemical vapor deposition and transferred to titanium via a polymer-assisted transfer technique. GN has high inertness and did not increase expression of inflammatory markers by macrophages, even in the presence of lipopolysaccharides. It kept high coverage at the top tercile of tapered dental implant collars after installation and removal from bone substitute and pig maxilla. It also resisted microbiologically influenced corrosion, and it maintained very high coverage area and quality after prolonged exposure to biofilms and their removal by different techniques. Our findings show that GN is unresponsive to harsh and inflammatory environments and that it maintains a promising level of structural integrity on the top tercile of dental implant collars, which is the area highly affected by biofilms during the onset of implant diseases. Our findings open the avenues for the clinical studies required for the use of GN in the development of implants that have higher osteogenic potential and are less prone to implant diseases.

Antibiofilm effects of titanium surfaces modified by laser texturing and hot-pressing sintering with silver

Peri-implant diseases are one of the main causes of dental implant failure. New strategies for dental implants manufacturing have been developed to prevent the accumulation of bacteria and related inflammatory reactions. The main aim of this work was to develop laser-treated titanium surfaces covered with silver that generate a electrical dipole to inhibit the oral bacteria accumulation. Two approaches were developed for that purpose. In one approach a pattern of different titanium dioxide thickness was produced on the titanium surface, using a Q-Switched Nd:YAG laser system operating at 1064 nm. The second approach was to incorporate silver particles on a laser textured titanium surface. The incorporation of the silver was performed by laser sintering and hot-pressing approaches. The anti-biofilm effect of the discs were tested against biofilms involving 14 different bacterial strains growth for 24 and 72 hr. The morphological aspects of the surfaces were evaluated by optical and field emission guns scanning electronical microscopy (FEGSEM) and therefore the wettability and roughness were also assessed. Physicochemical analyses revealed that the test surfaces were hydrophilic and moderately rough. The oxidized titanium surfaces showed no signs of antibacterial effects when compared to polished discs. However, the discs with silver revealed a decrease of accumulation of Porphyromonas gingivalis and Prevotella intermedia strains. Thus, the combination of Nd:YAG laser irradiation and hot-pressing was effective to produce silver-based patterns on titanium surfaces to inhibit the growth of pathogenic bacterial species. The laser parameters can be optimized to achieve different patterns, roughness, and thickness of the modified titanium layer regarding the type and region of the implant.

Remnant oral biofilm and microorganisms after autoclaving sterilization of retrieved healing abutments

OBJECTIVE

The purpose of this study was to evaluate the sterilization effectiveness against biofilms on retrieved healing abutments used in implant dentistry.

BACKGROUND

A large number of clinicians reuse healing abutments to decrease treatment costs although it can promote infection due to the presence of remnant biofilm biomass.

METHODS

One hundred and eighty-five titanium healing abutments previously used for 3 months in oral cavity were assessed in this study. Abutments were submitted to cleaning, chemical disinfection, and autoclave sterilization according to clinical guidelines. The abutments were aseptically placed into glass tubes containing specific bacterial growth medium and then incubated for 10 days. From glass tubes with bacterial growth, 100 µl medium was transferred to Schaedler's agar for morphological identification and counting of strict anaerobes and to Columbia blood agar for presumptive identification of facultative anaerobes after incubation. Isolated strains were then identified at species level by enzymatic and biochemical tests within API microorganism detection platform. Also, polymerase chain reaction (PCR) was performed for identification of undefined strains.

RESULTS

After the standard cleaning and sterilization procedures, fifty-six (approximately 30%) retrieved abutments showed the presence of remnant biofilm biomass. The bacteria identified into the remnant biofilms covering the abutments were representative of the commensal oral microbiota including Aggregatibacter actinomycetemcomitans, Prevotella intermedia, and Enterococcus faecalis.

CONCLUSION

Although some healing abutments did not reveal the existence of bacteria, organic components from biofilm biomass are still strongly adhered on the retentive micro-regions and surfaces of abutments and therefore that would support the accumulation of biofilm including pathogenic species leading to patients' cross-infections. Further studies should be performed on the assessment of different materials, design, and connections of the healing abutments associated with clinical disinfection procedures in implant dentistry.

Physical properties of epilithic river biofilm as a new lead to perform pollution bioassessments in overseas territories

Chlordecone (CLD) levels measured in the rivers of the French West Indies were among the highest values detected worldwide in freshwater ecosystems, and its contamination is recognised as a severe health, environmental, agricultural, economic, and social issue. In these tropical volcanic islands, rivers show strong originalities as simplified food webs, or numerous amphidromous migrating species, making the bioindication of contaminations a difficult issue. The objective of this study was to search for biological responses to CLD pollution in a spatially fixed and long-lasting component of the rivers in the West Indies: the epilithic biofilm. Physical properties were investigated through complementary analyses: friction, viscosity as well as surface adhesion were analyzed and coupled with measures of biofilm carbon content and exopolymeric substance (EPS) production. Our results have pointed out a mesoscale chemical and physical reactivity of the biofilm that can be correlated with CLD contamination. We were able to demonstrate that epilithic biofilm physical properties can effectively be used to infer freshwater environmental quality of French Antilles rivers. The friction coefficient is reactive to contamination and well correlated to carbon content and EPS production. Monitoring biofilm physical properties could offer many advantages to potential users in terms of effectiveness and ease of use, rather than more complex or time-consuming analyses.

Abutment misfit in implant-supported prostheses manufactured by casting technique: An integrative review

The aim of this study was to perform an integrative review of the literature on the clinically usual prosthesis-abutment misfit over implant-supported structures manufactured by conventional casting technique. The present integrative review used the PRISMA methodology. A bibliographical search was conducted on the following electronic databases: MEDLINE/PubMed (National Library of Medicine), Scopus (Elsevier), ScienceDirect (Elsevier), Web of Science (Thomson Reuters Scientific), Latin American and Caribbean Center on Health Sciences Information (BIREME), and Virtual Health Library (BVS). A total of 11 relevant studies were selected for qualitative analysis. The prosthetic-abutment vertical misfit considered clinically usual ranged from 50 to 160 μm. The vertical misfit depends on several steps during technical manufacturing techniques, which includes the materials and technical procedures. Lower values in misfit are recorded when precious metal or titanium alloys are utilized. Although a vertical misfit mean value of 100 μm has been considered clinically usual, most of the previous studies included in this revision showed lower mean values.

Physicochemical and microscopic characterization of implant-abutment joints

Objective:

The purpose of this study was to investigate Morse taper implant–abutment joints by chemical, mechanical, and microscopic analysis.

Materials and Methods:

Surfaces of 10 Morse taper implants and the correlated abutments were inspected by field emission gun-scanning electron microscopy (FEG-SEM) before connection. The implant–abutment connections were tightened at 32 Ncm. For microgap evaluation by FEG-SEM, the systems were embedded in epoxy resin and cross-sectioned at a perpendicular plane of the implant–abutment joint. Furthermore, nanoindentation tests and chemical analysis were performed at the implant–abutment joints.

Statistics:

Results were statistically analyzed via one-way analysis of variance, with a significance level of P < 0.05.

Results:

Defects were noticed on different areas of the abutment surfaces. The minimum and maximum size of microgaps ranged from 0.5 μm up to 5.6 μm. Furthermore, defects were detected throughout the implant–abutment joint that can, ultimately, affect the microgap size after connection. Nanoindentation tests revealed a higher hardness (4.2 ± 0.4 GPa) for abutment composed of Ti6Al4V alloy when compared to implant composed of commercially pure Grade 4 titanium (3.2 ± 0.4 GPa).

Conclusions:

Surface defects produced during the machining of both implants and abutments can increase the size of microgaps and promote a misfit of implant–abutment joints. In addition, the mismatch in mechanical properties between abutment and implant can promote the wear of surfaces, affecting the size of microgaps and consequently the performance of the joints during mastication.

Influence of contact configuration and lubricating conditions on the microtriboactivity of the zirconia-Ti6Al4V pair used in dental applications

Loosening and fracture of implanted dental crowns is a consequence of relative micromovements between the zirconia abutment and the titanium alloy of the implant, in a biochemical aggressive environment. Thus, it is important to establish the in vitro tribological testing conditions that better mimics such environment. The present work aims to evaluate the effect of ball-on-plate tests configuration on the tribological behavior of ZrO2/Ti6Al4V pair in dry and lubricated conditions, using different lubricants: water, artificial saliva solution and human saliva. Ceramic balls sliding on metallic plates (TiPlate) and metallic balls sliding on ceramic plates (TiBall) were tested and the coefficient of friction (CoF) and wear response was monitored trough nanotribological tests. Open circuit potential was also measured during the tests carried out in saline solution (artificial saliva) to access the tribochemical response. The wear mechanisms were evaluated by scanning electron microscopy and atomic force microscopy analysis. Relevant differences were found between the two configurations, with and without the presence of human saliva: TiPlate presented always a higher CoF than TiBall, which may have resulted from differences in the degradation and regeneration processes of the titanium passive film during sliding. TiBall demonstrated to be the best choice to reproduce the in vivo conditions, since the metallic surface contacts permanently with zirconia, impairing the titanium repassivation. Regarding the effect of the lubricants, it was observed that human saliva had a protective action of the surfaces, leading to the lowest CoF among the lubricants used (0.19 ± 0.05 for TiBall and 0.35 ± 0.08 for TiPlate) and neglectable wear.

Regenerative Medicine Strategies in Biomedical Implants

PURPOSE OF REVIEW

Recently, significant progress has been made in the research related to regenerative medicine. At the same time, biomedical implants in orthopedics and dentistry are facing many challenges and posing clinical concerns. The purpose of this chapter is to provide an overview of the clinical applications of current regenerative strategies to the fields of dentistry and orthopedic surgery. The main research question in this review is: What are the major advancement strategies in regenerative medicine that can be used for implant research?

RECENT FINDINGS

The implant surfaces can be modified through patient-specific stem cells and plasma coatings, which may provide methods to improve osseointegration and sustainability of the implant. Overall understanding from the review suggesting that the outcome from the studies could lead to identify optimum solutions for many concerns in biomedical implants and even in drug developments as a long-term solution to orthopedic and dental patients.

The Role of Oral Cavity Biofilm on Metallic Biomaterial Surface Destruction-Corrosion and Friction Aspects

Metallic biomaterials in the oral cavity are exposed to many factors such as saliva, bacterial microflora, food, temperature fluctuations, and mechanical forces. Extreme conditions present in the oral cavity affect biomaterial exploitation and significantly reduce its biofunctionality, limiting the time of exploitation stability. We mainly refer to friction, corrosion, and biocorrosion processes. Saliva plays an important role and is responsible for lubrication and biofilm formation as a transporter of nutrients for microorganisms. The presence of metallic elements in the oral cavity may lead to the formation of electro-galvanic cells and, as a result, may induce corrosion. Transitional microorganisms such as sulfate-reducing bacteria may also be present among the metabolic microflora in the oral cavity, which can induce biological corrosion. Microorganisms that form a biofilm locally change the conditions on the surface of biomaterials and contribute to the intensification of the biocorrosion processes. These processes may enhance allergy to metals, inflammation, or cancer development. On the other hand, the presence of saliva and biofilm may significantly reduce friction and wear on enamel as well as on biomaterials. This work summarizes data on the influence of saliva and oral biofilms on the destruction of metallic biomaterials.

Synergistic interactions between corrosion and wear at titanium-based dental implant connections: A scoping review

Two-piece implant systems are mainly used in oral implantology involving an osseointegrated implant connected to an abutment, which supports prosthetic structures. It is well documented that the presence of microgaps, biofilms and oral fluids at the implant-abutment connection can cause mechanical and biological complications. The aim of this review paper was to report the degradation at the implant-abutment connection by wear and corrosion processes taking place in the oral cavity. Most of the retrieved studies evaluated the wear and corrosion (tribocorrosion) of titanium-based materials used for implants and abutments in artificial saliva. Electrochemical and wear tests together with microscopic techniques were applied to validate the tribocorrosion behavior of the surfaces. A few studies inspected the wear on the inner surfaces of the implant connection as a result of fatigue or removal of abutments. The studies reported increased microgaps after fatigue tests. In addition, data suggest that micromovements occurring at the contacting surfaces can increase the wear of the inner surfaces of the connection. Biofilms and/or glycoproteins act as lubricants, although they can also amplify the corrosion of the surfaces. Consequently, loosening of the implant-abutment connection can take place during mastication. In addition, wear and corrosion debris such as ions and micro- and nanoparticles released into the surrounding tissues can stimulate peri-implant inflammation that can lead to pathologic bone resorption.

Wear of Morse taper and external hexagon implant joints after abutment removal

The aim of this in vitro study was to evaluate the removal torque values on abutments and the morphological wear aspects of two different dental implant joints after immersion in a medium containing biofilm from human saliva. Twenty implant-abutment assemblies were divided into four groups in this study: (A) Morse taper free of medium containing biofilm, and (B) after contact with a medium containing biofilm from human saliva; (C) External Hexagon free of medium containing biofilm, and (D) after contact with medium containing biofilm from human saliva. The abutments were firstly torqued to the implants according to the manufacturer´s recommendations, using a handheld torque meter. Groups B and D were immersed into 24 well-plates containing 2 ml BHI medium with microorganisms for 72 h at 37 °C under microaerophilic conditions. After detorque evaluation, the abutments were removed and the implants were analyzed by scanning electron microscopy (SEM) and profilometry. On the detorque evaluation, the torque values decreased for the external hexagon implants and increased for the Morse taper implants. However, the values were lower when both implant-abutment assemblies were in contact with a medium containing biofilm from human saliva. The wear areas of contacting surfaces of the implants were identified by SEM. The highest average roughness values were recorded on the surfaces free of biofilm. The medium containing biofilm from human saliva affected the maintenance of the torque values on Morse taper and external hexagon abutments. Additionally, the removal of abutment altered the inner implant surfaces resulting in an increase of wear of the titanium-based connection.

Biofilm Formation on Different Materials Used in Oral Rehabilitation

The aim of this study was to evaluate the density and the morphological aspects of biofilms adhered to different materials applied in oral rehabilitation supported by dental implants. Sixty samples were divided into four groups: feldspar-based porcelain, CoCr alloy, commercially pure titanium grade IV and yttria-stabilized zirconia. Human saliva was diluted into BHI supplemented with sucrose to grow biofilms for 24 or 48 h. After this period, biofilm was removed by 1% protease treatment and then analyzed by spectrophotometry (absorbance), colony forming unit method (CFU.cm-2) and field-emission guns scanning electron microscopy (FEG-SEM). The highest values of absorbance and CFU.cm-2 were recorded on biofilms grown on CoCr alloys when compared to the other test materials for 24 or 48 h. Also, FEG-SEM images showed a high biofilm density on CoCr. There were no significant differences in absorbance and CFU.cm-2 between biofilms grown on zirconia, porcelain and titanium (p<0.05). Microbiological assays associated with microscopic analyses detected a higher accumulation of oral biofilms on CoCr-based materials than that on titanium or zirconia that are used for prosthetic structures.

Chemical, microscopic, and microbiological analysis of a functionalized poly-ether-ether-ketone-embedding antibiofilm compounds

Poly-ether-ether-ketone (PEEK) is currently introduced as an alternative material for orthopedic implants due to its biocompatibility and low elastic modulus compared to titanium. Also, a sulphonation treatment can functionalize PEEK to embed therapeutical substances. The objective of this work was to functionalize a PEEK film to incorporate novel lactam-based antibiofilms compounds. PEEK samples were functionalized by sulphuric acid treatment and then dissolved in dimethylsulfoxide, where lactams were added to be incorporated into the polymer. A dip-coating technique was used to synthesize a thin film on a glass-based substrate. The degree of sulfonation (DS) and the incorporation of lactams into sulphonated PEEK (sPEEK) were analyzed by Fourier transform infrared spectroscopy, nuclear magnetic resonance, thermogravimetric analysis (TGA), and scanning electron microscopy. A DS of 65% was obtained and TGA curves confirmed the presence of SO₃ H and lactams in the sPEEK structure. The growth of Streptococcus mutans biofilm decreased on sPEEK surface containing lactams when compared to sPEEK free of lactams. That indicated the antibiofilm activity of those compounds was maintained after incorporation into sPEEK. Planktonic growth analysis showed no long distant effects of sPEEK containing lactams, indicating that no systemic effects should be expected upon clinical uses of medical devices produced with lactam-treated sPEEK. Results revealed that inclusion of lactams into sPEEK represents a good alternative for the production of biomaterials resistant to bacterial accumulation. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 3015-3020, 2016.

Lactam inhibiting Streptococcus mutans growth on titanium

The aim of this work was to analyze the activity of novel synthetic lactams on preventing biofilm formation on titanium surfaces. Titanium (Ti6Al4V) samples were exposed to Streptococcus mutans cultures in the presence or absence of a synthetic lactam. After 48h incubation, planktonic growth was determined by spectrophotometry. Biofilm was evaluated by crystal violet staining and colony forming units (CFU·ml(-)(1)), followed by scanning electron microscopy (SEM). Results showed that the average of adhered viable cells was approximately 1.5×10(2)CFU/ml in the presence of lactam and 4×10(2)CFU/ml in its absence. This novel compound was considerable active in reducing biofilm formation over titanium surfaces, indicating its potential for the development of antimicrobial drugs targeting the inhibition of the initial stages of bacterial biofilms on dental implants abutments.

Corrosion behaviour of titanium in the presence of Streptococcus mutans

OBJECTIVE

The main aim of this in vitro study was to evaluate the influence of Streptococcus mutans on the corrosion of titanium.

METHODS

S. mutans biofilms were formed on commercially pure titanium (CP-Ti) square samples (10mm×10mm×1mm) using a culture medium enriched with sucrose. Open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) measurements were used to evaluate the corrosion behaviour of CP-Ti in the presence of S. mutans in Fusayama's artificial saliva. The corrosion of biofilm-free CP-Ti samples was also evaluated in artificial saliva. Biofilms biomass was measured by spectrophotometry, using crystal violet staining, after 1, 2 and 7 days.

RESULTS

The OCP values recorded on CP-Ti in the presence of S. mutans (-0.3±0.02V vs. SCE) was lower than those on biofilm-free CP-Ti (-0.1±0.01V vs. SCE) after 2h of immersion in artificial saliva (p<0.05). That reveals a high reactivity of titanium in presence of S. mutans. Impedance spectra revealed the formation of a compact passive film on titanium in artificial saliva or in the presence of a 2 days old S. mutans biofilm even though the corrosion resistance of CP-Ti has decreased in presence of a S. mutans biofilm.

CONCLUSION

The presence of bacterial colonies, such as S. mutans, negatively affected the corrosion resistance of the titanium.

Simple physical approach to reducing frictional and adhesive forces on a TiO2 surface via creating heterogeneous nanopores

A simple physical strategy to reduce the frictional and adhesive forces on TiO(2) films was proposed by constructing mesoporous TiO(2) films with heterogeneously distributed nanopores on the film surfaces. In comparison, TiO(2) films with densely packed nanoparticles were also prepared. The crystal structure and morphology of the films were characterized with Raman spectroscopy, field emission scanning electron microscopy (FESEM), and atomic force microscopy (AFM). It was found that the TiO(2)(B) phase exists in the mesoporuos TiO(2) films but not in the densely packed films. The existence of TiO(2)(B) plays a significant role in creating and maintaining the nanopores in the mesoporous TiO(2) films. The frictional and adhesive forces were measured on both films using AFM. The mesoporous films exhibit two typical adhesion forces of around 3 and 12 nN in the force distribution profile whereas the densely packed films show only one around 12 nN. The frictional coefficients were 2.6 × 10(-3) and 6.7 × 10(-2) for the mesoporous and densely packed TiO(2) films, respectively. A model based on the atomic structures of a thin film of water molecules adsorbed on TiO(2) surfaces leading to hydrophobic effects was proposed to understand the lower frictional and adhesive forces observed on the mesoporous TiO(2) films. This simple physical approach to reducing the frictional and adhesive forces on TiO(2) films could have broad applications to a variety of surface coatings.

A strategy to establish a gene-activated matrix on titanium using gene vectors protected in a polylactide coating

Bioactive implants are promising tools in regenerative medicine. Here we describe a versatile procedure for preparing a gene-activated matrix on titanium. Lyophilized copolymer-protected gene vectors (COPROGs) suspended in poly(d,l-lactide) (PDLLA) solutions in ethyl acetate were used to varnish solid surfaces. The gene-activated PDLLA surfaces were first established on polypropylene 96-well plates. Vector release from these surfaces in aqueous buffer, cell viability and gene transfer efficiency to NIH 3T3 fibroblasts was strongly dependent on the vector dose and its ratio to PDLLA film thickness. A detailed analysis of these relationships allowed establishing correlations which can be used to calculate suitable combinations of COPROGs and PDLLA yielding optimal gene transfer efficiency. This was verified with COPROG-activated PDLLA coatings on titanium foils. HEK 293 and mesenchymal stem cells expressed the BMP-2 gene comprised in the gene-activated surface in a manner that was consistent with the predicted dose-response and toxicity profiles found in NIH 3T3 cells. The systematic procedure presented here for identifying optimal coating compositions can be applied to any combination of vector type and coating material.