Silver nanoparticles are broad-spectrum bactericidal and virucidal compounds

Fabrication of Poly(ethylene furanoate)/Silver and Titanium Dioxide Nanocomposites with Improved Thermal and Antimicrobial Properties

Poly(ethylene furanoate) (PEF)-based nanocomposites were fabricated with silver (Ag) and titanium dioxide (TiO2) nanoparticles by the in-situ polymerization method. The importance of this research work is to extend the usage of PEF-based nanocomposites with improved material properties. The PEF-Ag and PEF-TiO2 nanocomposites showed a significant improvement in color concentration, as determined by the color colorimeter. Scanning electron microscopy (SEM) photographs revealed the appearance of small aggregates on the surface of nanocomposites. According to crystallinity investigations, neat PEF and nanocomposites exhibit crystalline fraction between 0-6%, whereas annealed samples showed a degree of crystallinity value above 25%. Combining the structural and molecular dynamics observations from broadband dielectric spectroscopy (BDS) measurements found strong interactions between polymer chains and nanoparticles. Contact angle results exhibited a decrease in the wetting angle of nanocomposites compared to neat PEF. Finally, antimicrobial studies have been conducted, reporting a significant rise in inhibition of over 15% for both nanocomposite films against gram-positive and gram-negative bacteria. From the overall results, the synthesized PEF-based nanocomposites with enhanced thermal and antimicrobial properties may be optimized and utilized for the secondary packaging (unintended food-contact) materials.

Fluoride anodic films on stainless-steel fomites to reduce transmission infections

The growing concern arising from viruses with pandemic potential and multi-resistant bacteria responsible for hospital-acquired infections and outbreaks of food poisoning has led to an increased awareness of indirect contact transmission. This has resulted in a renewed interest to confer antimicrobial properties to commonly used metallic materials. The present work provides a full characterization of optimized fluoride anodic films grown in stainless steel 304L as well as their antimicrobial properties. Antibacterial tests show that the anodic film, composed mainly of chromium and iron fluorides, reduces the count and the percentage of the area covered by 50% and 87.7% for Pseudomonas aeruginosa and Stenotrophomonas maltophilia, respectively. Virologic tests show that the same treatment reduces the infectivity of the coronavirus HCoV-229E-GFP, in comparison with the non-anodized stainless steel 304L.IMPORTANCEThe importance of environmental surfaces as a source of infection is a topic of particular interest today, as many microorganisms can survive on these surfaces and infect humans through direct contact. Modification of these surfaces by anodizing has been shown to be useful for some alloys of medical interest. This work evaluates the effect of anodizing on stainless steel, a metal widely used in a variety of applications. According to the study, the fluoride anodic layers reduce the colonization of the surfaces by both bacteria and viruses, thus reducing the risk of acquiring infections from these sources.

Characterization, antibacterial, and cytotoxic activities of silver nanoparticles using the whole biofilm layer as a macromolecule in biosynthesis

Recently, multi-drug resistant (MDR) bacteria are responsible for a large number of infectious diseases that can be life-threatening. Globally, new approaches are targeted to solve this essential issue. This study aims to discover novel antibiotic alternatives by using the whole components of the biofilm layer as a macromolecule to synthesize silver nanoparticles (AgNPs) as a promising agent against MDR. In particular, the biosynthesized biofilm-AgNPs were characterized using UV-Vis spectroscopy, electron microscopes, Energy Dispersive X-ray (EDX), zeta sizer and potential while their effect on bacterial strains and normal cell lines was identified. Accordingly, biofilm-AgNPs have a lavender-colored solution, spherical shape, with a size range of 20-60 nm. Notably, they have inhibitory effects when used on various bacterial strains with concentrations ranging between 12.5 and 25 µg/mL. In addition, they have an effective synergistic effect when combined with phage ZCSE9 to inhibit and kill Salmonella enterica with a concentration of 3.1 µg/mL. In conclusion, this work presents a novel biosynthesis preparation of AgNPs using biofilm for antibacterial purposes to reduce the possible toxicity by reducing the MICs using phage ZCSE9.

Vanillin-Mediated Green-Synthesised Silver Nanoparticles' Characterisation and Antimicrobial Activity: An In-Vitro Study

Background and aim Nanoparticles in general due to their enhanced antimicrobial effects and other beneficial effects are used in dentistry. Silver nanoparticles (AgNPs) have emerged as the metal nanoparticle with the most advantages among the many types. The objective of the study was to synthesise vanillin-mediated AgNPs, then characterise those nanoparticles and assess their antimicrobial effectiveness. Materials and methods One-step synthesis of stable and crystalline AgNPs was done with vanillin as the reducing and capping agent. After being crushed into powder form, the produced AgNPs were subjected to characterisation. A scanning electron Microscope SEM) analysis was done for morphological details of the AgNPs. SEM with energy dispersive X-ray spectroscopy analysis (EDAX) and Fourier transform infrared (FTIR) testing were done for elemental analysis. AgNPs' antimicrobial properties were tested using the agar well diffusion technique. Results The SEM analysis revealed that the synthesized AgNps were porous and agglomerative clusters and varied in sizes between 30-35 nm. SEM-EDAX revealed the presence of 76.2 weight (wt)% Ag, 4.9 wt% carbon, and 18.9 wt% of oxygen. FTIR prominent peaks were observed at 1431.97 cm and 1361.20 cm indicating the presence of AgNPs. Both low and high concentrations of AgNps showed good antimicrobial effects against Streptococcus mutans (S. mutans). Conclusion Vanillin can be successfully used as a reducing agent for creating AgNPs. Due to their effective antimicrobial activity against S.mutans at various concentrations, vanillin-mediated AgNPs can be used with dental materials to reduce the risk of dental caries and enamel demineralization.

Promising applications of phyto-fabricated silver nanoparticles: Recent trends in biomedicine

The prospective contribution of phyto-nanotechnology to the synthesis of silver nanomaterials for biomedical purposes is attracting increasing interest across the world. Green synthesis of silver nanoparticles (Ag-NPs) through plants has been extensively examined recently, and it is now seen to be a green and efficient path for future exploitation and development of practical nano-factories. Fabrication of Ag-NPs is the process involves use of plant extracts/phyto-compounds (e.g.alkaloids, terpenoids, flavonoids, and phenolic compounds) to synthesise nanoparticles in more economical and feasible. Several findings concluded that in the field of medicine, Ag-NPs play a major role in pharmacotherapy (infection and cancer). Indeed, they exhibits novel properties but the reason is unclear (except some theoretical interpretation e.g. size, shape and morphology). But recent technological advancements help to address these questions by predicting the unique properties (composition and origin) by characterizing physical, chemical and biological properties. Due to increased list of publications and their application in the field of agriculture, industries and pharmaceuticals, issues relating to toxicity are unavoidable and question of debate. The present reviews aim to find out the role of plant extracts to synthesise Ag-NPs. It provides an overview of various phytocompounds and their role in the field of biomedicine (antibacterial, antioxidant, anticancer, anti-inflammatory etc.). In addition, this review also especially focused on various applications such as role in infection, oxidative stress, application in medical engineering, diagnosis and therapy, medical devices, orthopedics, wound healing and dressings. Additionally, the toxic effects of Ag-NPs in cell culture, tissue of different model organism, type of toxic reactions and regulation implemented to reduce associated risk are discussed critically. Addressing all above explanations, this review focus on the detailed properties of plant mediated Ag-NPs, its impact on biology, medicine and their commercial properties as well as toxicity.

Antimicrobial mechanism of cuprous oxide (Cu2O) coatings

Some very effective antimicrobial coatings exploit copper or cuprous oxide (Cu2O) as the active agent. The aim of this study is to determine which species is the active antimicrobial - dissolved ions, the Cu2O solid, or reactive oxygen species. Copper ions were leached from Cu2O into various solutions and the leachate tested for both dissolved copper and the efficacy in killing Pseudomonas aeruginosa. The concentration of copper species leached from Cu2O into aqueous solution varied greatly with the composition of the aqueous solution. For a range of solution buffers, killing of P. aeruginosa was highly correlated with the concentration of copper in the leachate. Further, 10 µL bacterial suspension droplets were placed on Cu2O coatings, with or without a polymer barrier layer, and tested for bacterial kill. Killing occurred without contact between bacterium and solid, demonstrating that contact with Cu2O is not necessary. We therefore conclude that soluble copper species are the antimicrobial agent, and that the most potent species is Cu+. The solid quickly raises and sustains the concentration of soluble copper species near the bacterium. Killing via soluble copper ions rather than contact should allow copper coatings to kill bacteria even when fouled, which is an important practical consideration.

Biomedical Approach of Nanotechnology and Biological Risks: A Mini-Review

Nanotechnology has played a prominent role in biomedical engineering, offering innovative approaches to numerous treatments. Notable advances have been observed in the development of medical devices, contributing to the advancement of modern medicine. This article briefly discusses key applications of nanotechnology in tissue engineering, controlled drug release systems, biosensors and monitoring, and imaging and diagnosis. The particular emphasis on this theme will result in a better understanding, selection, and technical approach to nanomaterials for biomedical purposes, including biological risks, security, and biocompatibility criteria.

Recent Updates on Multifunctional Nanomaterials as Antipathogens in Humans and Livestock: Classification, Application, Mode of Action, and Challenges

Pathogens cause infections and millions of deaths globally, while antipathogens are drugs or treatments designed to combat them. To date, multifunctional nanomaterials (NMs), such as organic, inorganic, and nanocomposites, have attracted significant attention by transforming antipathogen livelihoods. They are very small in size so can quickly pass through the walls of bacterial, fungal, or parasitic cells and viral particles to perform their antipathogenic activity. They are more reactive and have a high band gap, making them more effective than traditional medications. Moreover, due to some pathogen's resistance to currently available medications, the antipathogen performance of NMs is becoming crucial. Additionally, due to their prospective properties and administration methods, NMs are eventually chosen for cutting-edge applications and therapies, including drug administration and diagnostic tools for antipathogens. Herein, NMs have significant characteristics that can facilitate identifying and eliminating pathogens in real-time. This mini-review analyzes multifunctional NMs as antimicrobial tools and investigates their mode of action. We also discussed the challenges that need to be solved for the utilization of NMs as antipathogens.

Wound healing performance of electrospun PVA/70S30C bioactive glass/Ag nanoparticles mats decorated with curcumin: In vitro and in vivo investigations

Biocompatible fibrous scaffold containing polyvinyl alcohol (PVA), 70S30C bioactive glass (BG), silver (Ag) nanoparticles and curcumin (Cur) was fabricated through electrospinning method. Scanning electron microscope (SEM) and Field emission scanning electron microscopy (FESEM) were employed to investigate the morphological characteristics of the scaffolds. In addition, biodegradability, hydrophilicity, and contact angle were studied as criteria for evaluating physical properties of the scaffolds. Tensile strength was reported to be 0.971 ± 0.093 MPa. Also, the viability of fibroblasts after 7 days of cell culture was 93.58 ± 1.36 %. The antibacterial activity against Escherichia coli and Staphylococcus aureus bacteria was illustrated using inhibition zones of 13.12 ± 0.69 and 14.21 ± 1.37 mm, respectively. Histological results revealed that tissue regeneration after 14 days of surgery was much higher for the dressing group compared to the blank group. According to the obtained results, the authors introduce the PVA-BG-Ag-Cur scaffold as a promising candidate for skin tissue engineering applications.

Fabrication and characterization of novel, cost-effective graphitic carbon nitride/Fe coated textile nanocomposites for effective degradation of dyes and biohazards

Textile-based photocatalysts are the new materials that can be utilized as an effective sustainable solution for biochemical hazards. Hence, we aimed to develop a sustainable, cost-effective, and facile approach for the fabrication of photocatalytic fabric using graphitic carbon nitride (g-C3N4) and ferric-based multifunctional nanocomposite. Bulk g-C3N4 was prepared from urea by heating it at 500 °C for 2 h. The structure of ball-milled g-C3N4 was engineered by doping with various amounts of iron (III) chloride hexahydrate solution (0.006 mol/L) and sintered at 90 °C for 24 h to prepare g-C3N4-nanosheets/α-Fe2O3 composites. These nanocomposites have potential avenues towards rational designing of g-C3N4 for improved photocatalytic, antibacterial, and antiviral behavior. The prepared nanocomposite was characterized for its surface morphology, chemical composition, crystal structure, catalytic, antibacterial, and antiviral behavior. The fabrication of ferric doped g-C3N4 nanocomposites was characterized by SEM, EDX, FTIR, and XRD analysis. The coated fabric nanocomposite was characterized for methylene blue dye degradation under visible light, antibacterial and antiviral behavior. The developed textile-based photocatalyst has been found with very good recyclability with photocatalytic degradation of dye up to 99.9 % when compared to conventional g-C3N4 powder-based photocatalyst.

A programmed surface on dental implants sequentially initiates bacteriostasis and osseointegration

Osteogenesis surrounding dental implants is initiated by a series of early physiological events, including the inflammatory response. However, the persistence of an anti-infection surface often results in compromised histocompatibility and osseointegration. Here, we presented a programmed surface containing both silver nanoparticles (AgNPs) and silver ions (Ag+) with a heterogeneous structure and time-dependent functionalities. The AgNPs were located at the surface of the heparin-chitosan polyelectrolyte coating (PEM), whereas Ag+ was distributed at both the surface and inside of the coating under optimized conditions (pH=4). The optimized coating (Ag-4) exhibited potent bactericidal activity at the early stage (12 and 24 h after inoculation) and a sustained antibacterial efficacy in the subsequent stage (one or two weeks), as it gradually depleted. Furthermore, compared to coatings with sustained high silver concentrations in bacteria-cell coculture experiments, the degradable Ag-4 coating demonstrated improved cytocompatibility, better cell viability, and morphology over time. At a later stage (within one month), the in vivo test revealed that Ag-4-coated titanium had superior histocompatibility and osteogenesis outcomes compared to bare titanium in a bacteria-exposed environment. The programmed surface of dental implants presented in this study offers innovative ideas for sequential antibacterial effects and osseointegration.

Research hotspot and trend of chronic wounds: A bibliometric analysis from 2013 to 2022

Chronic wounds have been confirmed as a vital health problem facing people in the global population aging process. While significant progress has been achieved in the study of chronic wounds, the treatment effect should be further improved. The number of publications regarding chronic wounds has been rising rapidly. In this study, bibliometric analysis was conducted to explore the hotspots and trends in the research on chronic wounds. All relevant studies on chronic wounds between 2013 and 2022 were collected from the PubMed database of the Web of Science (WOS) and the National Center for Biotechnology Information (NCBI). The data were processed and visualised using a series of software. On that basis, more insights can be gained into hotspots and trends of this research field. Wound Repair and Regeneration has the highest academic achievement in the field of chronic wound research. The United States has been confirmed as the most productive country, and the University of California System ranks high among other institutions. Augustin, M. is the author of the most published study, and Frykberg, RG et al. published the most cited study. Furthermore, the hotspots of wound research over the last decade were identified (e.g., bandages, infection and biofilms, pathophysiology and therapy). This study will help researchers gain insights into chronic wound research's hotspots and trends accurately and quickly. Moreover, the exploration of bacterial biofilm and the pathophysiological mechanism of the chronic wound will lay a solid foundation and clear direction for treating chronic wounds.

Enhancement of physicochemical characterization of nanocomposites on Ag+/Fe2+ codoped hydroxyapatite for antibacterial and anticancer properties

The synthesis of nanosized Ag+/Fe2+ codoped hydroxyapatite (HAp) nanocomposite materials with antibacterial and anticancer characteristics is highly attractive for advancing the development of biological applications. The objective of this study was to evaluate the antibacterial and anticancer characteristics of Ag+/Fe2+ codoped hydroxyapatite materials. We developed a facile chemical precipitation method for the fabrication of Ag+/Fe2+:HAp nanocomposites. The developed Ag+/Fe2+:HAp nanocomposite materials were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). For measuring the size of Ag+/Fe2+:HAp nanocomposites, dynamic light scattering (DLS) is an advantageous method. The chemical states and chemical composition of Ag+/Fe2+:HAp were observed by X-ray photoelectron spectroscopy (XPS) analysis. In addition, the antibacterial efficacy of Ag+/Fe2+:HAps against Gram-positive (S.aureus), and Gram-negative (S.typhi, and E.Coli) microorganisms is examined in this current study. Ag+/Fe2+:HAp nanocomposite materials have been evaluated for biological toxicity in vitro, and the results showed that the particles were excellent at identifying and killing cancer cells. In this respect, Ag+/Fe2+:HAp nanocomposites significantly impact human colon cancer cells (HT29) while have no effect on normal fibroblast cells (L929).

Biosynthesis of silver nanoparticles using nitrate reductase from Aspergillus terreus N4 and their potential use as a non-alcoholic disinfectant

Green technology has been developed for the quick production of stabilized silver nanoparticles (AgNPs), with the assistance of nitrate reductase from an isolated culture of Aspergillus terreus N4. The organism's intracellular and periplasmic fractions contained nitrate reductase, with the former demonstrating the highest activity of 0.20 IU/g of mycelium. When the fungus was cultivated in a medium comprising 1.056% glucose, 1.836% peptone, 0.3386% yeast extract, and 0.025% KNO3, the greatest nitrate reductase productivity of 0.3268 IU/g was achieved. Statistical modeling via response surface methodology was used to optimize the enzyme production. The periplasmic and intracellular enzyme fractions were found to convert Ag+ to Ag0, initiating synthesis within 20 min, with predominant nanoparticle sizes between 25 and 30 nm. By normalizing the effects of temperature, pH, AgNO3 concentration, and mycelium age with a variable shaking period for enzyme release, the production of AgNPs with the periplasmic fraction was optimized. The synthesis of nanoparticles occurred at temperatures of 30, 40, and 50 °C, with the highest yield observed at 40 and 50 °C during shorter incubation periods. Similarly, the nanoparticles were synthesized at pH levels of 7.0, 8.0, and 9.0, with the greatest production observed at pH 8.0 and 9.0 at lower incubation periods. The antimicrobial activity of AgNPs was demonstrated against common foodborne pathogens, including Staphylococcus aureus and Salmonella typhimurium, indicating their potential as non-alcoholic disinfectants.

Green Synthesized Silver Nanoparticles Loaded in Polysaccharide Hydrogel Applied to Chronic Wound Healing in Mice Models

The prevalence of chronic wounds is increasing owing to the expanding population and the growing number of individuals suffering from diabetes. Such a chronic wound continues to be a significant healthcare burden for diabetic patients because it frequently carries a high chance of limb loss due to amputation and reduces survival as a result. Development of innovative wound dressing materials with the potential to stop bacterial infections and accelerate the process of tissue regeneration is needed to increase the effectiveness of diabetic wound healing. In the current study, a co-polymerization process based on a free radical reaction was used to create a hydrogel of polysaccharides blend graft acrylamide (PsB-g-Am). Starch, chitosan, and alginate make up the polysaccharides blend (PsB). The produced hydrogel's structure was characterized using FTIR spectroscopy. The antibacterial activities of silver nanoparticles synthesized through the green method using garlic bulb (Allium sativum) is reported. The silver nanoparticles' physical characteristics were examined using scanning electron microscopy, transmission electron microscopy analysis, and UV-visible spectroscopy and they were found to range in size from 50 to 100 nm. The agar well diffusion technique is used to investigate the antibacterial characteristics. Inclusion of silver nanoparticles in the hydrogels demonstrated concentration-dependent antibacterial behavior against Gram-negative Klebsiella pneumoniae and Gram-positive Staphylococcus aureus during antimicrobial testing of the hydrogels. When hydrogels were applied to diabetic mice, the system was examined for its healing abilities, and positive therapeutic results were obtained in as little as 14 days. Thus, it can be inferred that graft copolymer of chitosan-AgNPs hydrogels can promote healing in chronic wounds over time and can be utilized as an alternative to conventional therapies for chronic wounds (such as those brought on by diabetes) in mouse models.

Facile fabrication of Nishamalaki churna mediated silver nanoparticles with antibacterial application

Antimicrobial resistance (AMR) is one of the most serious threats to today's healthcare system. The prime factor behind increasing AMR is the formation of complex bacterial biofilms which acts as the protective shield between the bacterial cell and the antimicrobial drugs. Among various nanoformulations, green synthesized metallic silver nanoparticles are currently gaining research focus in safely breaking bacterial biofilms due to the inherent antimicrobial property of silver. In the current work, the aqueous extract of the ayurvedic formulation Nishamalaki churna is used to exhibit one pot green synthesis of silver nanoparticles. The physicochemical characteristics of Nishamalaki churna extract mediated AgNPs were evaluated using various analytical techniques, like UV-Visible spectrophotometer, FT-IR spectroscopy, SEM, XRD, DLS-Zeta potential analyzer etc. The synthesized spherical AgNPs were well formed within the size range of 30 nm to 80 nm. Furthermore, the synthesized AgNPs showed potent antibacterial effects against two primary AMR-causing bacterial species like Staphylococcus aureus and Pseudomonas aeruginosa with the successful destruction of their biofilm formation. Additionally, these AgNPs have shown profound antioxidant and anti-inflammatory activities as desirable add-on effects required by a prospective antibacterial agent.

Nanosilver: An Old Antibacterial Agent with Great Promise in the Fight against Antibiotic Resistance

Antibiotic resistance in bacteria is a major problem worldwide that costs 55 billion USD annually for extended hospitalization, resource utilization, and additional treatment expenditures in the United States. This review examines the roles and forms of silver (e.g., bulk Ag, silver salts (AgNO3), and colloidal Ag) from antiquity to the present, and its eventual incorporation as silver nanoparticles (AgNPs) in numerous antibacterial consumer products and biomedical applications. The AgNP fabrication methods, physicochemical properties, and antibacterial mechanisms in Gram-positive and Gram-negative bacterial models are covered. The emphasis is on the problematic ESKAPE pathogens and the antibiotic-resistant pathogens of the greatest human health concern according to the World Health Organization. This review delineates the differences between each bacterial model, the role of the physicochemical properties of AgNPs in the interaction with pathogens, and the subsequent damage of AgNPs and Ag+ released by AgNPs on structural cellular components. In closing, the processes of antibiotic resistance attainment and how novel AgNP-antibiotic conjugates may synergistically reduce the growth of antibiotic-resistant pathogens are presented in light of promising examples, where antibiotic efficacy alone is decreased.

Broad-Spectrum, Potent, and Durable Ceria Nanoparticles Inactivate RNA Virus Infectivity by Targeting Virion Surfaces and Disrupting Virus-Receptor Interactions

There is intense interest in developing long-lasting, potent, and broad-spectrum antiviral disinfectants. Ceria nanoparticles (CNPs) can undergo surface redox reactions (Ce³⁺ ↔ Ce⁴⁺) to generate ROS without requiring an external driving force. Here, we tested the mechanism behind our prior finding of potent inactivation of enveloped and non-enveloped RNA viruses by silver-modified CNPs, AgCNP1 and AgCNP2. Treatment of human respiratory viruses, coronavirus OC43 and parainfluenza virus type 5 (PIV5) with AgCNP1 and 2, respectively, prevented virus interactions with host cell receptors and resulted in virion aggregation. Rhinovirus 14 (RV14) mutants were selected to be resistant to inactivation by AgCNP2. Sequence analysis of the resistant virus genomes predicted two amino acid changes in surface-located residues D91V and F177L within capsid protein VP1. Consistent with the regenerative properties of CNPs, surface-applied AgCNP1 and 2 inactivated a wide range of structurally diverse viruses, including enveloped (OC43, SARS-CoV-2, and PIV5) and non-enveloped RNA viruses (RV14 and feline calicivirus; FCV). Remarkably, a single application of AgCNP1 and 2 potently inactivated up to four sequential rounds of virus challenge. Our results show broad-spectrum and long-lasting anti-viral activity of AgCNP nanoparticles, due to targeting of viral surface proteins to disrupt interactions with cellular receptors.

Omicron SARS-CoV-2 antiviral on poly(lactic acid) with nanostructured copper coating: Wear effects

Surface modification corresponds to a set of viable technological approaches to introduce antimicrobial properties in materials that do not have such characteristics. Antimicrobial materials are important to prevent the proliferation of microorganisms and minimize the transmission of diseases caused by pathogens. Herein, poly(lactic acid) (PLA) was decorated with nanocones through copper sputtering followed by a plasma etching. Antiviral assays by Quantitative Reverse Transcription-Polymerase Chain Reaction (RT-qPCR) show that nanostructured Cu-coated PLA has high antiviral activity against Omicron SARS-CoV-2, showing a relative reduction in the amplified RNA (78.8 ± 3.9 %). Atomic Force Microscopy (AFM), X-ray Photoelectron Spectroscopy (XPS), and wear-resistance tests show that 20 wear cycles disrupt the surface nanocone patterns and significantly reduce the Cu content at the surface of the nanostructured Cu-coated PLA, leading to total loss of the antiviral properties of nanostructured PLA against Omicron SARS-CoV-2.

Innovative Functional Biomaterials as Therapeutic Wound Dressings for Chronic Diabetic Foot Ulcers

The imbalance of local and systemic factors in individuals with diabetes mellitus (DM) delays, or even interrupts, the highly complex and dynamic process of wound healing, leading to diabetic foot ulceration (DFU) in 15 to 25% of cases. DFU is the leading cause of non-traumatic amputations worldwide, posing a huge threat to the well-being of individuals with DM and the healthcare system. Moreover, despite all the latest efforts, the efficient management of DFUs still remains a clinical challenge, with limited success rates in treating severe infections. Biomaterial-based wound dressings have emerged as a therapeutic strategy with rising potential to handle the tricky macro and micro wound environments of individuals with DM. Indeed, biomaterials have long been related to unique versatility, biocompatibility, biodegradability, hydrophilicity, and wound healing properties, features that make them ideal candidates for therapeutic applications. Furthermore, biomaterials may be used as a local depot of biomolecules with anti-inflammatory, pro-angiogenic, and antimicrobial properties, further promoting adequate wound healing. Accordingly, this review aims to unravel the multiple functional properties of biomaterials as promising wound dressings for chronic wound healing, and to examine how these are currently being evaluated in research and clinical settings as cutting-edge wound dressings for DFU management.

Role of medicinal herbs and phytochemicals in post burn management

Burn management is a natural and distinctly programmed process involving overlapping phases of hemostasis, inflammation, proliferation and remodeling. Burn wound healing involves initiation of inflammation, re-epithelialization, granulation, neovascularization and wound contraction. Despite the availability of multiple preparations for management of burn wound, there is dire need for efficacious alternative agents. Current approaches for burn wound management include pharmaceutical agents and antibiotics. However, high cost of synthetic drugs and accelerated resistance to antibiotics is challenging for both developed and developing nations. Among alternative options, medicinal plants have been a biocompatible, safe and affordable source of preventive/curative approaches. Due to cultural acceptance and patient compliance, there has been a focus on the use of botanical drugs and phytochemicals for burn wound healing. Keeping in consideration of medicinal herbs and phytochemicals as suitable therapeutic/adjuvant agents for burn wound management, this review highlights therapeutic potential of 35 medicinal herbs and 10 phytochemicals. Among these, Elaeis guineensis, Ephedra ciliate and Terminalia avicennioides showed better burn wound healing potential with varied mechanisms such as modulation of TNF-alpha, inflammatory cytokines, nitric oxide, eicosanoids, ROS and leukocyte response. Phytochemicals (oleanolic acid, ursolic acid, kirenol) also showed promising role in burn wound management though various pathways involving such as down regulation of TNF-alpha, IL-6 and inflammatory mediators including plasma proteases and arachidonic acid metabolites. This review provides a pavement for therapeutic/adjuvant use of potential botanical drugs and novel druggable phyto-compounds to target skin burn injury with diverse mechanisms, affordability and safety profile.

The impact of bioactive textiles on human skin microbiota

In order to support the elevated market demand for the development of textiles with specific benefits for a healthy and safe lifestyle, several bioactive textiles with defined properties, including antimicrobial, antioxidant, anti-inflammatory, anti-odor, and anti-repellent, anti-ultraviolet (UV) radiation, have been proposed. Antimicrobial textiles, particularly, have received special interest considering the search for smart, protective textiles that also impact health and well-being. Although the incorporation of antimicrobials into textile material has been well succeeded, the addition of such components in textile clothing can influence the balance of the skin microbiota of the wearer. While most antimicrobial textiles have demonstrated good biocompatibility and antimicrobial performance against bacteria, fungi, and viruses, some problems such as textile biodegradation, odor, and dissemination of unwanted microorganisms might arise. However, little is known about the impact of such antimicrobial textile-products on human skin microbiota. To address this issue, the present review, for the first time, gives an overview about the main effects of antimicrobial textiles, i.e., antibacterial, antifungal, and antiviral, on skin microbiota while driving future investigation to elucidate their putative clinical relevance and possible applications according to their impact on skin microbiota. This knowledge may open doors for the development of more microbiota friendly textiles or antimicrobial textile-products able to target specific populations of the skin microbiota aiming to alleviate skin disorders, malodor, and allergies by avoiding the growth and spread of pathogenic microorganisms.

Effect of Biosynthesized Silver Nanoparticles on the Growth of the Green Microalga Haematococcus pluvialis and Astaxanthin Synthesis

Silver nanoparticles (AgNPs) are widely known for their antimicrobial activity in various systems from microorganisms to cell cultures. However, the data on their effects on microalgae are very limited. Unicellular green algae Haematococcus pluvialis is known for its ability to accumulate large amounts of astaxanthin under stress conditions. Therefore, it can be used as a suitable model system to test the influence of AgNPs on stress induction in unicellular algae, with visible phenotypic effects, such as astaxanthin synthesis and cell morphology. This study tested different AgNP concentrations (0-8 mg/L) effects on different growth stages (red and green) of H. pluvialis culture. Effects on cell morphology, culture productivity, and astaxanthin synthesis were evaluated. Data showed that the addition of high concentrations of AgNPs to the growing culture had a significant negative impact on culture productivity. Green-stage (HpG) cultures productivity was reduced by up to 85% by increasing AgNPs concentration to 8 mg/L while the impact on red-stage (HpR) culture was lower. Astaxanthin concentration measurements showed that AgNPs do not have any effect on astaxanthin concentration in HpG culture and caused decreased astaxanthin production rate in HpR culture. HpG culture astaxanthin concentration stayed constant at ~0.43% dry weight, while HpR culture astaxanthin concentration was significantly reduced from 1.89% to 0.60% dry weight by increasing AgNP concentration. AgNPs in the media lead to significant changes in cell morphology in both HpG and HpR cultures. Cell deformations and disrupted cytokinesis, as well as AgNPs and induced sexual reproduction, were observed.

Metal-Polymer Nanocomposites: A Promising Approach to Antibacterial Materials

There has been a new approach in the development of antibacterials in order to enhance the antibacterial potential. The nanoparticles are tagged on to the surface of other metals or metal oxides and polymers to achieve nanocomposites. These have shown significant antibacterial properties when compared to nanoparticles. In this article we explore the antibacterial potentials of metal-based and metal-polymer-based nanocomposites, various techniques which are involved in the synthesis of the metal-polymer, nanocomposites, mechanisms of action, and their advantages, disadvantages, and applications.

Osteogenic and long-term antibacterial properties of Sr/Ag-containing TiO2 microporous coating in vitro and in vivo

Bacterial infection and poor osseointegration are two critical issues that need to be solved for long-term use of titanium implants. As such, Sr/Ag-containing TiO₂ microporous coatings were prepared on a Ti alloy surface in the current study via a single-step microarc oxidation technique. The coatings showed both good cytocompatibility in vitro and biosafety in vivo. Sr/Ag incorporation brought no significant change in the surface micromorphology and physicochemical properties, but endowed the coating with strong osteogenic activity and long-term antibacterial capability in vitro. Furthermore, the osteogenic and antibacterial capability of the coating was also confirmed in vivo. In a rat osseointegration model, new bone formation, implant-bone contact, removal torque and bone mineralization were all significantly increased in the M-Sr/Ag group when compared with those in group M, although they were slightly lower than those in group M-Sr. In a periimplantitis model, no rats suffered infection in the M-Sr/Ag group after 3 months of osseointegration and 5 weeks of bacterial inoculation period, when compared to 100% and 75% infection rates in M and M-Sr groups, respectively. In addition, active bone remodeling and many mesenchymal cells were observed in the M-Sr group, suggesting good bone regeneration potential in Sr-containing coatings in the case of controlled periimplantitis. Overall, the Sr/Ag-containing TiO₂ microporous coating is valuable for preventing periimplantitis and improving implant reosseointegration, and is therefore promising for long-term and high quality use of titanium implants.

Functional nano-systems for transdermal drug delivery and skin therapy

Transdermal drug delivery is one of the least intrusive and patient-friendly ways for therapeutic agent administration. Recently, functional nano-systems have been demonstrated as one of the most promising strategies to treat skin diseases by improving drug penetration across the skin barrier and achieving therapeutically effective drug concentrations in the target cutaneous tissues. Here, a brief review of functional nano-systems for promoting transdermal drug delivery is presented. The fundamentals of transdermal delivery, including skin biology and penetration routes, are introduced. The characteristics of functional nano-systems for facilitating transdermal drug delivery are elucidated. Moreover, the fabrication of various types of functional transdermal nano-systems is systematically presented. Multiple techniques for evaluating the transdermal capacities of nano-systems are illustrated. Finally, the advances in the applications of functional transdermal nano-systems for treating different skin diseases are summarized.

Biosynthesis of silver nanoparticles using Pseudomonas canadensis, and its antivirulence effects against Pseudomonas tolaasii, mushroom brown blotch agent

This study reports the biosynthesis of silver nanoparticles (AgNPs) using a Pseudomonas canadensis Ma1 strain isolated from wild-growing mushrooms. Freshly prepared cells of P. canadensis Ma1 incubated at 26-28 °C with a silver nitrate solution changed to a yellowish brown color, indicating the formation of AgNPs, which was confirmed by UV-Vis spectroscopy, scanning electron microscopy (SEM), and X-ray diffraction. SEM analysis showed spherical nanoparticles with a distributed size mainly between 21 and 52 nm, and the XRD pattern revealed the crystalline nature of AgNPs. Also, it provides an evaluation of the antimicrobial activity of the biosynthesized AgNPs against Pseudomonas tolaasii Pt18, the causal agent of mushroom brown blotch disease. AgNPs were found to be bioactive at 7.8 μg/ml showing a minimum inhibitory concentration (MIC) effect against P. tolaasii Pt18 strain. AgNPs at the MIC level significantly reduced virulence traits of P. tolaasii Pt18 such as detoxification of tolaasin, various motility behavior, chemotaxis, and biofilm formation which is important for pathogenicity. Scanning electron microscopy (SEM) revealed that bacterial cells treated with AgNPs showed a significant structural abnormality. Results showed that AgNPs reduced brown blotch symptoms in vivo. This research demonstrates the first helpful use of biosynthesized AgNPs as a bactericidal agent against P. tolaasii.

Molecular toxicity and defense mechanisms induced by silver nanoparticles in Drosophila melanogaster

The widely use of silver nanoparticles (AgNPs) as antimicrobial agents gives rise to potential environmental risks. AgNPs exposure have been reported to cause toxicity in animals. Nevertheless, the known mechanisms of AgNPs toxicity are still limited. In this study, we systematically investigated the toxicity of AgNPs exposure using Drosophila melanogaster. We show here that AgNPs significantly decreased Drosophila fecundity, the third-instar larvae weight and rates of pupation and eclosion in a dose-dependent manner. AgNPs reduced fat body cell viability in MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assays. AgNPs caused DNA damage in hemocytes and S2 cells. Interestingly, the mRNA levels of the entire metallothionein gene family were increased under AgNPs exposure as determined by RNA-seq analysis and validated by qRT-PCR, indicating that Drosophila responded to the metal toxicity of AgNPs by producing metallothioneins for detoxification. These findings provide a better understanding of the mechanisms of AgNPs toxicity and may provide clues to effect on other organisms, including humans.

Can Differently Stabilized Silver Nanoparticles Modify Calcium Phosphate Precipitation?

Calcium phosphates (CaPs) composites with silver nanoparticles (AgNPs) attract attention as a possible alternative to conventional approaches to combating orthopedic implant-associated infections. Although precipitation of calcium phosphates at room temperatures was pointed out as an advantageous method for the preparation of various CaP-based biomaterials, to the best of our knowledge, no such study exists for the preparation of CaPs/AgNP composites. Motivated by this lack of data in this study we investigated the influence of AgNPs stabilized with citrate (cit-AgNPs), poly(vinylpyrrolidone) (PVP-AgNPs), and sodium bis(2-ethylhexyl) sulfosuccinate (AOT-AgNPs) in the concentration range 5-25 mg dm^-3 on the precipitation of CaPs. The first solid phase to precipitate in the investigated precipitation system was amorphous calcium phosphate (ACP). The effect of AgNPs on ACP stability was significant only in the presence of the highest concentration of AOT-AgNPs. However, in all precipitation systems containing AgNPs, the morphology of ACP was affected, as gel-like precipitates formed in addition to the typical chain-like aggregates of spherical particles. The exact effect depended on the type of AgNPs. After 60 min of reaction time, a mixture of calcium-deficient hydroxyapatite (CaDHA) and a smaller amount of octacalcium phosphate (OCP) formed. PXRD and EPR data point out that the amount of formed OCP decreases with increasing AgNPs concentration. The obtained results showed that AgNPs can modify the precipitation of CaPs and that CaPs properties can be fine-tuned by the choice of stabilizing agent. Furthermore, it was shown that precipitation can be used as a simple and fast method for CaP/AgNPs composites preparation which is of special interest for biomaterials preparation.

Nanoscale Interaction Mechanisms of Antiviral Activity

Nanomaterials have now found applications across all segments of society including but not limited to energy, environment, defense, agriculture, purification, food medicine, diagnostics, and others. The pandemic and the vulnerability of humankind to emerging viruses and other infectious diseases has renewed interest in nanoparticles as a potential new class of antivirals. In fact, a growing body of evidence in the literature suggests nanoparticles may have activity against multiple viruses including HIV, HNV, SARS-CoV-2, HBV, HCV, HSV, RSV, and others. The most described antiviral nanoparticles include copper, alloys, and oxides including zinc oxide (ZnO), titanium oxide, iron oxide, and their composites, nitrides, and other ceramic nanoparticles, as well as gold and silver nanoparticles, and sulfated and nonsulfated polysaccharides and other sulfated polymers including galactan, cellulose, polyethylenimine, chitosan/chitin, and others. Nanoparticles, synthesized via the biological or green method, also have great importance and are under major consideration these days, as their method of synthesis is easy, reliable, cost-effective, efficient, and eco-friendly, and is done using easily available sources such as bacteria, actinomycetes, yeast, fungi, algae, herbs, and plants, in comparison to chemically mediated synthesis. Chemical synthesis is highly expensive and involves toxic solvents, high pressure, energy, and high temperature conversion. Examples of biologically synthesized NPs include iron oxide, Cu and CuO NPs, and platinum and palladium NPs. In contrast to traditional medications, nanomedications have multiple advantages: their small size, increased surface to volume ratio, improved pharmacokinetics, improved biodistribution, and targeted delivery. In terms of antiviral activity, nanoscale interactions represent a unique mode of action. As reviewed here their biomedical application as an antiviral has shown four major mechanisms: (1) direct viral interaction prohibiting the virus from infecting the cell, (2) interaction to receptor or cell surface preventing the virus from entering the host cells, (3) preventing the replication of the virus, or (4) other processing mechanisms which inhibit the spread of virus. Here these pharmacologic mechanisms are reviewed and the challenges for technology translation are discussed in more detail.

Immunostimulants for shrimp aquaculture: paving pathway towards shrimp sustainability

At present, food security is a matter of debate of global magnitude and fulfilling the feeding requirement of > 8 billion human populations by 2030 is one of the major concerns of the globe. Aquaculture plays a significant role to meet the global food requirement. Shrimp species such as Litopenaeus vannamei, Penaeus monodon, and Macrobrachium rosenbergii are among the most popular food commodities worldwide. As per Global Outlook for Aquaculture Leadership survey, disease outbreaks have been a matter of concern from the past many decades regarding the shrimp aquaculture production. Among the past disease outbreaks, white spot disease caused by the white spot syndrome virus is considered to be one of the most devastating ones that caused colossal losses to the shrimp industry. Since the virus is highly contagious, it spreads gregariously among the shrimp population; hence, practicing proper sanitization practices is crucial in order to have disease-free shrimps. Additionally, in order to control the disease, antibiotics were used that further leads to bioaccumulation and biomagnification of antibiotics in several food webs. The bioaccumulation of the toxic residues in the food webs further adversely affected human too. Recently, immunostimulants/antivirals were used as an alternative to antibiotics. They were found to enhance the immune system of shrimps in eco-friendly manner. In context to this, the present paper presents a critical review on the immunostimulants available from plants, animals, and chemicals against WSSV in shrimps. Looking into this scenario, maintaining proper sanitation procedures in conjunction with the employment of immunostimulants may be a viable approach for preserving shrimp aquaculture across the globe.

Tutorial review on the processing and performance of fabrics with antipathogenic inorganic agents

Functionalized textiles have been increasingly used for enhancing antimicrobial or antiviral (antipathogenic) action. Those pathogens can cause recurring diseases by direct or indirect transmission. Particularly, airborne microorganisms may cause respiratory diseases or skin infections like allergies and acne and the use of inorganic agents such as metal and metal oxides has proven effective in antipathogen applications. This review is a tutorial on how to obtain functional fabric with processes easily applied for industrial scale. Also, this paper summarizes relevant textiles and respective incorporated inorganic agents, including their antipathogenic mechanism of action. In addition, the processing methods and functional finishing, on a laboratory and industrial scale, to obtain a functional textile are shown. Characterization techniques, including antipathogenic activity and durability, mechanical properties, safety, and environmental issues, are presented. Challenges and perspectives on the broader use of antipathogenic fabrics are discussed.

Emerging Trends in Advanced Translational Applications of Silver Nanoparticles: A Progressing Dawn of Nanotechnology

Nanoscience has emerged as a fascinating field of science, with its implementation in multiple applications in the form of nanotechnology. Nanotechnology has recently been more impactful in diverse sectors such as the pharmaceutical industry, agriculture sector, and food market. The peculiar properties which make nanoparticles as an asset are their large surface area and their size, which ranges between 1 and 100 nanometers (nm). Various technologies, such as chemical and biological processes, are being used to synthesize nanoparticles. The green chemistry route has become extremely popular due to its use in the synthesis of nanoparticles. Nanomaterials are versatile and impactful in different day to day applications, resulting in their increased utilization and distribution in human cells, tissues, and organs. Owing to the deployment of nanoparticles at a high demand, the need to produce nanoparticles has raised concerns regarding environmentally friendly processes. These processes are meant to produce nanomaterials with improved physiochemical properties that can have significant uses in the fields of medicine, physics, and biochemistry. Among a plethora of nanomaterials, silver nanoparticles have emerged as the most investigated and used nanoparticle. Silver nanoparticles (AgNPs) have become vital entities of study due to their distinctive properties which the scientific society aims to investigate the uses of. The current review addresses the modern expansion of AgNP synthesis, characterization, and mechanism, as well as global applications of AgNPs and their limitations.

Dual mode antibacterial surfaces based on Prussian blue and silver nanoparticles

Prussian Blue (PB) is an inexpensive, biocompatible, photothermally active material. In this paper, self-assembled monolayers of PB nanoparticles were grafted on a glass surface, protected with a thin layer of silica and decorated with spherical silver nanoparticles. This combination of a photothermally active nanomaterial, PB, and an intrinsically antibacterial one, silver, leads to a versatile coating that can be used for medical devices and implants. The intrinsic antibacterial action of nanosilver, always active over time, can be enhanced on demand by switching on the photothermal effect of PB using near infrared (NIR) radiation, which has a good penetration depth through tissues and low side effects. Glass surfaces functionalized by this layer-by-layer approach have been characterized for their morphology and composition, and their intrinsic and photothermal antibacterial effect was studied against Gram+ and Gram- planktonic bacteria.

SARS-CoV-2 and its new variants: a comprehensive review on nanotechnological application insights into potential approaches

SARS-CoV-2 (COVID-19) spreads and develops quickly worldwide as a new global crisis which has left deep socio-economic damage and massive human mortality. This virus accounts for the ongoing outbreak and forces an urgent need to improve antiviral therapeutics and targeted diagnosing tools. Researchers have been working to find a new drug to combat the virus since the outbreak started in late 2019, but there are currently no successful drugs to control the SARS-CoV-2, which makes the situation riskier. Very recently, new variant of SARS-CoV-2 is identified in many countries which make the situation very critical. No successful treatment has yet been shown although enormous international commitment to combat this pandemic and the start of different clinical trials. Nanomedicine has outstanding potential to solve several specific health issues, like viruses, which are regarded a significant medical issue. In this review, we presented an up-to-date drug design strategy against SARS-CoV-2, including the development of novel drugs and repurposed product potentials were useful, and successful drugs discovery is a constant requirement. The use of nanomaterials in treatment against SARS-CoV-2 and their use as carriers for the transport of the most frequently used antiviral therapeutics are discussed systematically here. We also addressed the possibilities of practical applications of nanoparticles to give the status of COVID-19 antiviral systems.

Nanomaterials-Functionalized Hydrogels for the Treatment of Cutaneous Wounds

Hydrogels have been utilized extensively in the field of cutaneous wound treatment. The introduction of nanomaterials (NMs), which are a big category of materials with diverse functionalities, can endow the hydrogels with additional and multiple functions to meet the demand for a comprehensive performance in wound dressings. Therefore, NMs-functionalized hydrogels (NMFHs) as wound dressings have drawn intensive attention recently. Herein, an overview of reports about NMFHs for the treatment of cutaneous wounds in the past five years is provided. Firstly, fabrication strategies, which are mainly divided into physical embedding and chemical synthesis of the NMFHs, are summarized and illustrated. Then, functions of the NMFHs brought by the NMs are reviewed, including hemostasis, antimicrobial activity, conductivity, regulation of reactive oxygen species (ROS) level, and stimulus responsiveness (pH responsiveness, photo-responsiveness, and magnetic responsiveness). Finally, current challenges and future perspectives in this field are discussed with the hope of inspiring additional ideas.

Strategies to Mitigate and Treat Orthopaedic Device-Associated Infections

Orthopaedic device implants play a crucial role in restoring functionality to patients suffering from debilitating musculoskeletal diseases or to those who have experienced traumatic injury. However, the surgical implantation of these devices carries a risk of infection, which represents a significant burden for patients and healthcare providers. This review delineates the pathogenesis of orthopaedic implant infections and the challenges that arise due to biofilm formation and the implications for treatment. It focuses on research advancements in the development of next-generation orthopaedic medical devices to mitigate against implant-related infections. Key considerations impacting the development of devices, which must often perform multiple biological and mechanical roles, are delineated. We review technologies designed to exert spatial and temporal control over antimicrobial presentation and the use of antimicrobial surfaces with intrinsic antibacterial activity. A range of measures to control bio-interfacial interactions including approaches that modify implant surface chemistry or topography to reduce the capacity of bacteria to colonise the surface, form biofilms and cause infections at the device interface and surrounding tissues are also reviewed.

Nano-antivirals: A comprehensive review

Nanoparticles can be used as inhibitory agents against various microorganisms, including bacteria, algae, archaea, fungi, and a huge class of viruses. The mechanism of action includes inhibiting the function of the cell membrane/stopping the synthesis of the cell membrane, disturbing the transduction of energy, producing toxic reactive oxygen species (ROS), and inhibiting or reducing RNA and DNA production. Various nanomaterials, including different metallic, silicon, and carbon-based nanomaterials and nanoarchitectures, have been successfully used against different viruses. Recent research strongly agrees that these nanoarchitecture-based virucidal materials (nano-antivirals) have shown activity in the solid state. Therefore, they are very useful in the development of several products, such as fabric and high-touch surfaces. This review thoroughly and critically identifies recently developed nano-antivirals and their products, nano-antiviral deposition methods on various substrates, and possible mechanisms of action. By considering the commercial viability of nano-antivirals, recommendations are made to develop scalable and sustainable nano-antiviral products with contact-killing properties.

The Study of Nanosized Silicate-Substituted Hydroxyapatites Co-Doped with Sr2+ and Zn2+ Ions Related to Their Influence on Biological Activities

Nanosized silicate-substituted hydroxyapatites, characterized by the general formula Ca_9.8-x-nSr_nZn_x(PO₄)_6-y(SiO₄)_y(OH)₂ (where: n = 0.2 [mol%]; x = 0.5-3.5 [mol%]; y = 4-5 [mol%]), co-doped with Zn²⁺ and Sr²⁺ ions, were synthesized with the help of a microwave-assisted hydrothermal technique. The structural properties were determined using XRD (X-ray powder diffraction) and Fourier-transformed infrared spectroscopy (FT-IR). The morphology, size and shape of biomaterials were detected using scanning electron microscopy techniques (SEM). The reference strains of Klebsiella pneumoniae, Escherichia coli and Pseudomonas aeruginosa were used to assess bacterial survivability and the impact on biofilm formation in the presence of nanosilicate-substituted strontium-hydroxyapatites. Safety evaluation was also performed using the standard cytotoxicity test (MTT) and hemolysis assay. Moreover, the mutagenic potential of the materials was assessed (Ames test). The obtained results suggest the dose-dependent antibacterial activity of nanomaterials, especially observed for samples doped with 3.5 mol% Zn²⁺ ions. Moreover, the modification with five SiO₄ groups enhanced the antibacterial effect; however, a rise in the toxicity was observed as well. No harmful activity was detected in the hemolysis assay as well as in the mutagenic assay (Ames test).

Computer Simulation of the Interaction between SARS-CoV-2 Spike Protein and the Surface of Coinage Metals

A prominent feature of the SARS-CoV-2 virus is the presence of a large glycoprotein spike protruding from the virus envelope. The spike determines the interaction of the virus with the environment and the host. Here, we used an all-atom molecular dynamics simulation method to investigate the interaction of up- and down-conformations of the S1 subunit of the SARS-CoV-2 spike with the (100) surface of Au, Ag, and Cu. Our results revealed that the spike protein is adsorbed onto the surface of these metals, with Cu being the metal with the highest interaction with the spike. In our simulations, we considered the spike protein in both its up-conformation S^up (one receptor binding domain exposed) and down-conformation S^down (no exposed receptor binding domain). We found that the affinity of the metals for the up-conformation was higher than their affinity for the down-conformation. The structural changes in the spike in the up-conformation were also larger than the changes in the down-conformation. Comparing the present results for metals with those obtained in our previous MD simulations of S^up with other materials (cellulose, graphite, and human skin models), we see that Au induces the highest structural change in S^up, larger than those obtained in our previous studies.

Strong anti-viral nano biocide based on Ag/ZnO modified by amodiaquine as an antibacterial and antiviral composite

In this paper, we synthesized Ag/ZnO composite colloidal nanoparticles and the surface of nanoparticles was improved by amodiaquine ligand. The synthesized nanoparticles were characterized using the XRD diffraction pattern, FT-IR Spectroscopy, TEM image, and UV-Vis spectroscopy. The antibacterial, antifungal, and antiviral effects of the synthesized colloid were examined on E.coli, Staphylococcus aureus, Pseudomonas aeruginosa, and Enterococcus hirae bacteria, and Candida Albicans and form spore aspergillus fungi, also influenza, herpes simplex, and covid 19 viruses. The results indicate more than 7 log removal of the bacteria, fungi, and viruses by synthesized colloid with a concentration of 15 μg/L (Ag)/50 µg/ml (ZnO). This removal for covid 19 virus is from 3.2 × 10⁸ numbers to 21 viruses within 30 s. Also, irritation and toxicity tests of the synthesized colloid show harmless effects on human cells and tissues. These colloidal nanoparticles were used as mouthwash solution and their clinical tests were done on 500 people infected by the coronavirus. The results indicate that by washing their mouth and nose three times on day all patients got healthy at different times depending on the depth of the disease. Almost all people with no signs of infection and using this solution as a mouthwash didn't infect by the virus during the study.

Chitosan-Based Formulations Intended as Protective Spray for Mask Surfaces in Prevention of Coronavirus Dissemination

The extraordinary occurrence of COVID-19 by the fast expansion of viral infections has propelled particular interest in developing novel antiviral and virucidal agents to guarantee personal security. The main objective of this work is to propose novel formulations able to optimize the use of personal protection elements. In recent years, chitosan (CH) has attracted attention for being an interesting multifunctional, biodegradable, non-antigenic, non-toxic, and biocompatible natural polymer with antimicrobial properties. In this work, formulations based on a CH matrix containing silver, and Copper based nanoparticles have been developed. The novelty of this proposal is that almost liquid formulations have been reached, possessing verified properties to inhibit evolved virus such as herpes simplex type 1 (HSV-1) and bovine betacoronavirus (BCoV), the latter belonging to the same family of the well-known the well-known SARS-CoV-2. Besides antibacterial bioactivity; as well as the ability of these formulations to be easily sprayed on various surfaces, including conventional face masks, have been verified and discussed. The results presented in this contribution provide strong evidence on CH films as an ideal biosafe surface-protective for several daily used materials including the conventional face masks.

Recent Advances in Silver Nanoparticles Containing Nanofibers for Chronic Wound Management

Infections are the primary cause of death from burns and diabetic wounds. The clinical difficulty of treating wound infections with conventional antibiotics has progressively increased and reached a critical level, necessitating a paradigm change for enhanced chronic wound care. The most prevalent bacterium linked with these infections is Staphylococcus aureus, and the advent of community-associated methicillin-resistant Staphylococcus aureus has posed a substantial therapeutic challenge. Most existing wound dressings are ineffective and suffer from constraints such as insufficient antibacterial activity, toxicity, failure to supply enough moisture to the wound, and poor mechanical performance. Using ineffective wound dressings might prolong the healing process of a wound. To meet this requirement, nanoscale scaffolds with their desirable qualities, which include the potential to distribute bioactive agents, a large surface area, enhanced mechanical capabilities, the ability to imitate the extracellular matrix (ECM), and high porosity, have attracted considerable interest. The incorporation of nanoparticles into nanofiber scaffolds constitutes a novel approach to “nanoparticle dressing” that has acquired significant popularity for wound healing. Due to their remarkable antibacterial capabilities, silver nanoparticles are attractive materials for wound healing. This review focuses on the therapeutic applications of nanofiber wound dressings containing Ag-NPs and their potential to revolutionize wound healing.

Lactoferrin-Conjugated Nanoparticles as New Antivirals

Lactoferrin is an iron-binding glycoprotein with multiple functions in the body. Its activity against a broad spectrum of both DNA and RNA viruses as well as the ability to modulate immune responses have made it of interest in the pharmaceutical and food industries. The mechanisms of its antiviral activity include direct binding to the viruses or its receptors or the upregulation of antiviral responses by the immune system. Recently, much effort has been devoted to the use of nanotechnology in the development of new antivirals. In this review, we focus on describing the antiviral mechanisms of lactoferrin and the possible use of nanotechnology to construct safe and effective new antiviral drugs.

Evaluation of setting time, tear strength, dimensional stability and antimicrobial property of silver and titanium nanoparticles incorporated elastomeric impression material

Graph 1: Graph represents the dimensional stability of Group I and Group II samples.Image 1.

A nanomaterial targeting the spike protein captures SARS-CoV-2 variants and promotes viral elimination

The global emergency caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic can only be solved with effective and widespread preventive and therapeutic strategies, and both are still insufficient. Here, we describe an ultrathin two-dimensional CuInP2S6 (CIPS) nanosheet as a new agent against SARS-CoV-2 infection. CIPS exhibits an extremely high and selective binding capacity (dissociation constant (KD) < 1 pM) for the receptor binding domain of the spike protein of wild-type SARS-CoV-2 and its variants of concern, including Delta and Omicron, inhibiting virus entry and infection in angiotensin converting enzyme 2 (ACE2)-bearing cells, human airway epithelial organoids and human ACE2-transgenic mice. On association with CIPS, the virus is quickly phagocytosed and eliminated by macrophages, suggesting that CIPS could be successfully used to capture and facilitate virus elimination by the host. Thus, we propose CIPS as a promising nanodrug for future safe and effective anti-SARS-CoV-2 therapy, and as a decontamination agent and surface-coating material to reduce SARS-CoV-2 infectivity.