Functionalization of carbon from rubber fruit shells (Hevea brasiliensis) with silane agents and its application to the adsorption of bi-component mixtures of methylene blue and crystal violet

In this research, activated carbon was obtained from rubber fruit shells (ACRPs). The obtained activated carbon (ACRPs) was modified by magnetite particle coating and silanization with triethoxyiphenylsilane (TEPS) to produce a new magnetic adsorbent (ACRPs-MS). The affinity of as-prepared adsorbent (ACRPs-MS) toward methylene blue (MB) and crystal violet (CV) dyes was tested in mono-component and bi-component solutions. Structural characterization proves the success of the magnetite coating process and the silanization of ACRPs. In the infrared (IR) spectroscopy spectrum of ACRPs-MS, Si-O-Fe and Si-O-Si bonds were identified, which indicated the presence of magnetite and silane. This is also supported by the elemental composition contained in the energy-dispersive X-ray (EDX) diffractogram. In addition, the presence of the porous structure of the surface of the material and the increase in the specific surface area increase the accessibility of contaminants such as MB and CV dyes to be adsorbed to the ACRPs-MS adsorption site effectively. The experimental results showed that the adsorption of mono-component MB and CV dyes by ACRPs-MS was optimum at pH 8 and an interaction time of 60 min. The adsorption kinetics of mono-component MB and CV dyes by ACRPs-MS tended to follow pseudo-second-order kinetics (PSO) models with PSO rate constant (k2) values of 0.198 and 0.993 g mg-1 min-1, respectively. The adsorption of MB and CV dyes by ACRPs-MS in a bi-component mixture tends to follow the Langmuir isotherm model with adsorption capacity (qm) values of 85.060 and 90.504 mg g-1, respectively. Analysis of adsorption data on the bi-component mixture between MB and CV by ACRPs-MS with the Langmuir isotherm equation for a binary mixture resulted in qm of 22.645 × 10-3 mmol equiv g-1. ACRPs-MS material can be used repeatedly five times with adsorption ability > 80%. Desorption of MB and CV dyes was carried out using 0.05 M HCl solution. ACRPs-MS material was able to adsorb MB and CV dyes with a large adsorption capacity and could be used in repeated adsorption. Thus, it can be stated that ACRPs-MS can be used as an effective adsorbent for MB and CV dyes, either singly or in a bi-component mixture.

Extractability of Rice Husk Waste Using Green Gamma Radiation for Dye Elimination in Laboratory-Scale Sorption System: Equilibrium Isotherm and Kinetic Analysis

Nowadays, the use of natural materials and especially "waste" valorization has evolved and attracted the wide attention of scientists and academia. In this regard, the use of rice husk (RH) powder as a naturally abundant and cheap byproduct material is gaining superior attention. However, improving the physicochemical properties of such RH is still under research. In the current investigation, the modification of rice husk (RH) via γ-irradiation has shown to be a promising green tool to meet such a need. Clean, prepared, powdered RH samples were subjected to various γ-radiation doses, namely 5, 10, 15 and 25 kGy, and the corresponding samples were named as RH-0, RH-5, RH-10, RH-15, RH-15 and RH-25. Then, the samples were characterized via scanning electron microscopy (SEM). After irradiation, the samples showed an increase in their surface roughness upon increasing the γ-radiation up to 15 kGy. Furthermore, the sorption capacity of the irradiated RH samples was investigated for eliminating Urolene Blue (UB) dye as a model pharmaceutical effluent stream. The highest dye uptake was recorded as 14.7 mg/g, which corresponded to the RH-15. The adsorption operating parameters were also investigated for all of the studied systems and all adsorbents showed the same trend, of a superior adsorption capacity at pH 6.6 and high temperatures. Langmuir and Freundlich isotherm models were also applied for UB adsorption and an adequate fitted isotherm model was linked with Langmuir fitting. Moreover, the pseudo-second-order kinetic model provided the best fit for the adsorption data. Experimental assays confirmed that the UB dye could be successfully eradicated feasibly from the aqueous stream via a sustainable green methodology.

Adsorption Potential of Schizophyllum commune White Rot Fungus for Degradation of Reactive Dye and Condition Optimization: A Thermodynamic and Kinetic Study

The pollution due to dyes from textile sector is one of the major issues faced worldwide. This study was focused on the removal of the reactive dye, Drimaren Turquoise CL-B using Schizophyllum commune, a white rot fungus (WRF) keeping in mind the current environmental conditions. Different parameters like pH, sources of carbon & nitrogen, temperature, concentration of dye and C/N ratio were used to investigate their effect on the process. Maximum dye removal of 95.45% was obtained at pH 4.5, temperature 35°C, inoculum size 3 mL, veratryl alcohol (mediator), glucose (carbon source) and ammonium nitrate (nitrogen source). The enzyme activity was determined by employing enzyme assay. Laccase and Lignin peroxidase (LiP) activity was low while Manganese peroxidase (MnP) activity was highest. Maximum bio-sorption was achieved at pH 1 and 313 K. The pseudo-2nd-order kinetic model & Freundlich isotherm was best suited for the process of removal of dye. From these data, it is concluded that white rot fungus could possibly be the excellent biomaterial for elimination of synthetic dyes from wastewater.

Ionizing radiation based advanced oxidation process for reactive orange 122 dye degradation and kinetics studies

In the current study, the degradation of reactive orange 122 (RO 122) dye was carried out under UV and gamma irradiation in presence of H2O2. The effect of variables such as UV exposure time, gamma-ray absorbed dose, initial concentration of dye and oxidant dose were investigated. The removal of 64.10, 58.84 and 55.46 (%) was observed for 50, 100 and 150 (mg/L) dye concentrations, respectively using UV radiation time of 150 (min). The degradation was enhanced to 80.39, 69.95 and 67.01 (%) when UV radiation was employed in the presence of H2O2 (0.5 mL/L) for above concentrations respectively. The degradation was further improved to 97, 92.54 and 81.32 (%) using 5 kGy absorbed dose along with H2O2 (0.5 mL/L). The reduction in chemical oxygen demand (COD) was 77, 64 and 57 (%) using UV/H2O2 (0.5 mL/L), while 63, 56 and 53 (%) in case of gamma/H2O2 for aforementioned concentrations. The removal efficiency (G-value), dose constants (k), dose indispensable for 50, 90 and 99 (%) degradation (D 0.5, D 0.90, and D 0.99) after the treatment with gamma radiation were determined. The G-value was noted as 0.46–0.0711 for 50–150 mg/L dye concentration for gamma irradiated samples which improved to 0.57–0.1204 for above mentioned concentrations in presence of H2O2. The FTIR analysis showed that all the peaks were disappeared using gamma/H2O2 at 5 kGy absorbed dose except a minor peak of −CO stretching. The degradation mechanism of dye followed pseudo-first-order kinetics. A significant decrease in peak area was observed by the HPLC analysis after treating the dye samples with gamma/H2O2 (0.5 mL/L) at absorbed dose of 5 kGy which has proven the process efficiency for dye degradation.

Biochar caged zirconium ferrite nanocomposites for the adsorptive removal of Reactive Blue 19 dye in a batch and column reactors and conditions optimizaton

Biochar caged zirconium ferrite (BC-ZrFe2O5) nanocomposites were fabricated and their adsorption capacity for Reactive Blue 19 (RB19) dye was evaluated in a fixed-bed column and batch sorption mode. The adsorption of dye onto BC-ZrFe2O5 NCs followed pseudo-second-order kinetics (R 2 = 0.998) and among isotherms, the experimental data was best fitted to Sips model as compared to Freundlich and Langmuir isotherms models. The influence of flow-rate (3–5 mL min−1), inlet RB19 dye concentration (20–100 mg L−1) and quantity of BC-ZrFe2O5 NCs (0.5–1.5 g) on fixed-bed sorption was elucidated by Box-Behnken experimental design. The saturation times (C t /C o  = 0.95) and breakthrough (C t /C o  = 0.05) were higher at lower flow-rates and higher dose of BC-ZrFe2O5 NCs. The saturation times decreased, but breakthrough was increased with the initial RB19 dye concentration. The treated volume was higher at low sorbent dose and influent concentration. Fractional bed utilization (FBU) increased with RB19 dye concentration and flow rates at low dose of BC-ZrFe2O5 NCs. Yan model was fitted best to breakthrough curves data as compared to Bohart-Adams and Thomas models. Results revealed that BC-ZrFe2O5 nanocomposite has promising adsorption efficiency and could be used for the adsorption of dyes from textile effluents.

Greener approach to substitute chemical reduction clearing process for fabric dyed with Foron Blue E-BL 150, Foron Rubine RD-GFL and Foron Brilliant Yellow S-6GL using indigenous resources

Fabric dyed with disperse dyes followed a reduction clearing process (RCP)/chemical clearing process (CCP) to remove the unfixed dye from the fabric. In the clearing process, unfixed dyes and chemicals are discharged into streams. To combat this issue, an environment friendly approaches is explored that is a biological clearing using indigenous fungal strains of white-rot fungi (Pleurotus ostreatus and Ganoderma lucidum). In this context, fabrics dyed with three disperse dyes (Foron Blue E-BL 150, Foron Rubine RD-GFL and Foron Brilliant Yellow S-6GL) were considered. The fabric cleared with biological clearing process improved the quality of fabric versus chemically cleared fabric and among the tested strains, G. lucidum showed higher efficiency for color strength improvement. However, no significant difference in tensile and tear strength of all fabric samples was observed. The quality of effluents in clearing reduction process for three dyes was assessed and it was observed that water quality parameters including chemical oxygen demand (COD), total organic carbon (TOC), biological oxygen demand (BOD), total suspended solids (TSS), pH, dissolved oxygen (DO) and total dissolved solids (TDS) improved significantly and results revealed that the biological clearing approach can substitute chemical reduction clearing process for fabric dyed with dyes, which is greener and eco-friendly versus conventional processes to avoid unfixed dyes discharge in to water bodies.

Cobalt doping of nickel ferrites via sol gel approach: effect of doping on the structural and dielectric properties

Cobalt doped nickel ferrites were fabricated by sol gel route and the dielectric constant, tangent loss and AC conductivity were investigated as a function of Co doping. The X-ray diffractometer characterization confirmed that the Co x Ni1−x Fe2O4 with doping concentration (x = 0.1, 0.2, 0.3, 0.4, and 0.5) have cubic spinel structure. In the XRD spectrum there appear extra peaks of Fe2O3 as an impurity that is gradually disappear by increasing doping ratio of cobalt ions, which is an indication of high crystallinity. The structural parameters (lattice constant, grain size, dislocation density, X-rays density and packing factor) are greatly influenced by the doping of cobalt atoms i.e., lattice constant increases. The crystal size increases from 30 to 42.26 nm by cobalt substitution in the pure nickel ferrites. The Fourier Transform IR Spectroscopy indicate shift in peaks to lower frequency region because cobalt doping reduced binding energy between metal ion and oxygen ions. Atomic structure of cobalt doped nickel ferrites examined by the Raman spectroscopy. Co x Ni1−x Fe2O4 shows Raman mode at ∼285, ∼477, ∼563, ∼624 and ∼704 cm−1. There is unnoticeable Raman shift due to the doping of cobalt’s atoms.

Thermodynamic and kinetic approach of biodiesel production from waste cooking oil using nano-catalysts

This study focusses on the production of biodiesel by reacting the heterogeneous based nano-catalysts with used cooking oil in the presence of methanol. The CZO nanoparticles (NPs) were synthesized by co-precipitation method and characterized by different techniques. Biodiesel was characterized by the gas chromatograph (GC) and Fourier Transform Infra-red Spectroscopy (FTIR). Optimum conditions for the maximum biodiesel yield (90%) were 0.2% (w/w) catalyst dose, 3:1 methanol to oil ratio, 50 °C reaction temperature, 150 min reaction time and 136 rpm stirring speed. The kinetic modeling and the thermodynamic factors like enthalpy (ΔH), activation energy (Ea), entropy (ΔS) and free energy (ΔG) were operated on all the data. Mean and standard deviation was used for analysis of data. The results indicate the maximum biodiesel yield under the optimum reaction conditions, which is promising to reduce the pollution such as air pollution and greenhouse effect for sustainable environmetal development.

Synthesis, characterization and photocatalytic application of Sophora mollis leaf extract mediated silver nanoparticles

This study reports green synthesis and characterization of silver nanoparticles (Ag NPs) from Sophora mollis leaf extract. The use of S. mollis extract for preparation of Ag NPs was investigated using different techniques. Dark brown color indicates formation of nanoparticles. Fourier transform infra-red (FTIR) analysis revealed that plant extract act as a reducing and capping agent. Morphological aspects of Ag NPs were ascertained by means of SEM studies. Energy dispersive and FTIR spectroscopy results showed chemical composition and plant extract functionality respectively. X-ray diffraction (XRD) analysis showed particle size of 70 nm. Antibacterial activity of NPs was investigated by disc diffusion and minimum inhibitory concentration method. Antioxidant activity of NPs was shown by DPPH assay. The photo catalytic efficiency of synthesized Ag NPs was evaluated by degradation of methylene blue (MB) dye under UV irradiation. Ag NPs degraded MB dye up to 88% in 160 min. It is concluded that these NPs could be employed for degradation of toxic industrial effluents. Result proved the green synthesis of Ag NPs from S. mollis extract is clean, economical and safe method.

Synthesis of Cu-doped MgO and its enhanced photocatalytic activity for the solar-driven degradation of disperse red F3BS with condition optimization

In the present study, Cu (2–12%) doped MgO was synthesized and characterized by SEM, XRD, EDX, and FTIR spectroscopy. The Cu concentration significantly affected the band gap and particle size, which ranged from 4.63 to 3.78 eV and from 27.2 to 79 nm, respectively. In addition, the photocatalytic activity (PCA) of Cu-doped MgO was monitored by the photocatalytic destruction of disperse red F3BS coralene dye, and four reaction variables such as dye concentration, catalyst dose, hydrogen peroxide concentration, and irradiation time, respectively, were optimized by response surface methodology (RSM). Dye degradation was significantly affected by these process variables, and a degradation rate of up to 93% was achieved under optimized conditions. The wastewater samples were also treated under optimized conditions and water quality variables, i.e., chemical oxygen demand (COD) and biochemical oxygen demand (BOD) were significantly improved after treatment. Cu-doped MgO exhibited excellent PCA under the solar-light exposure for the degradation of disperse red F3BS dye, which can be employed for the treatment of dye-containing effluents.

Synthesis and characterization of magnetically separable La1−x Bi x Cr1−y Fe y O3 and photocatalytic activity evaluation under visible light

A series of Bi and Fe doped La1−x Bi x Cr1−y Fe y O3 (x = 0.00–0.10 and y = 0.02–0.12) perovskites were fabricated through a facile microemulsion method and were characterized by XRD, DC electrical-resistivity, dielectric, VSM, and UV–Visible measurements. Orthorhombic phase of synthesized substituted chromite nanocrystallite was confirmed by powdered XRD analysis with crystallite size in 47.8–32.9 nm range. DC electrical resistivity was observed to increase from 1.70–39.99 × 108 Ω-cm. Dielectric parameters analyzed in frequency range of 20 kHz–20 MHz were decreased, while magnetic parameters were observed to increase with the increase in dopant (Bi+3 and Fe+3) concentration. Whereas coercivity values was low (narrow hysteresis loop), which indicate the soft ferromagnetic of the prepared material materials which are quite useful to employ in storage devices and electronics. Moreover, La1−x Bi x Cr1−y Fe y O3 degraded 90.80% Rhodamine B dye under visible light irradiation within 55 min. The increase in electrical resistivity, while decrease in dielectric parameters was also observed with increase in dopant concentration, ferromagnetic nature and excellent photocatalytic properties make this material suitable for high frequency energy devices, microwave appliances as well as an excellent magnetically separable photocatalyst for the purification of contaminated wastewater.

Hydrothermal route for the synthesis of manganese ferrite nanoparticles and photocatalytic activity evaluation for the degradation of methylene blue dye

Manganese ferrite (MnFe2O4) was prepared via hydrothermal route and characterized by advanced techniques. The photocatalytic activity (PCA) was evaluated by degrading methylene blue (MB) dye under UV irradiation. The effect of process variables such as catalyst dose, UV exposure time and pH was studied for maximum degradation of dye at optimum conditions. The MnFe2O4 showed face centered cubic structure and average particle size of 23.98 nm. The lattice constant, lattice strain, ionic radii (rA & rB), bonding angles and hoping lengths of MnFe2O4 were recorded to be 0.8467 nm, 0.08, 1.66, 0.766, 1.833 and 2.116 Å, respectively. The MnFe2O4 showed promising PCA and at optimum conditions of process variable, up to 99% MB dye degradation was achieved. The PCA was found dependent to catalyst dose, UV exposure time and pH. Results revealed that the hydrothermal rout is feasible route for the preparation of MnFe2O4 ferrite in nano size and the PCA revealed the potential application of MnFe2O4 ferrite to degrade dye in textile wastewater.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

ZnO, CuO and Fe2O3 green synthesis for the adsorptive removal of direct golden yellow dye adsorption: kinetics, equilibrium and thermodynamics studies

In the present investigation, ZnO, CuO and Fe2O3 were prepared via green route and utilized for the sequestration of DGY (Direct Golden Yellow) dye. Affecting variables i.e., temperature, contact time, adsorbent dose and pH were optimized for maximum sequestration of dye from aqueous medium. The pH 2, adsorbent dose 0.1 g/50 mL dye solution, temperature 30 °C and 50 mg/L dye initial concentration were best levels for efficient dye adsorption and equilibrium was attained in 30 min reaction time. The dye sequestration on to ZnO, CuO and Fe2O3 was an exothermic process. Freundlich and Temkin adsorption isotherms explained well the dye adsorption onto nanoadsorbents and dye adsorption followed pseudo first order kinetic model. Effect of electrolytes and heavy metal ions was also investigated and both affected the adsorption process significantly. In the presences of surfactant/detergent, the removal of dye was reduced and 0.5 N NaOH efficiently desorbed the dye from nanoadsorbents. Findings depicted that the nanoadsorbents are effectual for the sequestration of DGY dye, which can be employed for the remediation of textile effluents.

Kinetic and thermodynamic studies for evaluation of adsorption capacity of fungal dead biomass for direct dye

This study focuses on evaluation of degradation aptitude of white rot fungus (Coriolus versicolor) against Indosol Turquoise FBL dye. The outcome of numerous parameters including pH, temperature, carbon sources, nitrogen sources, C/N ratio and effect of dye concentration were studied. Maximum decolorization (99.896%) of Indosol Turquoise FBL was obtained by C. versicolor under optimized conditions. After three days, the maximum dye degradation (98%) was observed at pH 4 and 30 °C. Six carbon sources fructose, glucose, maltose, sucrose, rice bran and wheat bran were used and 96.66% degradation was observed by maltose at its optimum growth concentration (0.1 g/100 mL). Various nitrogen sources were employed for decolorization but ammonium nitrate decolorized dye up to 98.05%. The activity of three different enzymes laccase, Lignin peroxidase (LiP) and Manganese peroxidase (MnP) were calculated. The dead biomass of White rot fungus (WRF) was used for biosorption experiments. Maximum q (36 mg/g) was obtained at pH 2, at 30 °C using 0.05 g biosorbent. An increase in the q value was observed with increase in dye concentration. Freundlich adsorption isotherm and pseudo second order kinetics were followed by the data. It can be concluded that C. versicolor could be an efficient source for degradation of dyes from industrial effluents.

Gamma and UV radiations induced treatment of anti-cancer methotrexate drug in aqueous medium: Effect of process variables on radiation efficiency evaluated using bioassays

This studystudy focuses on the effect of radiation treatment and hydrogen peroxide (H₂O₂) on the toxicity of anticancer methotrexate. For cytotoxicity, different bioassays such as Allium cepa, hemolytic, brine shrimp were employed. The Ames test was used for mutagenicity analysis. The solutions having concentrations 5, 10 and 15 ppm were irradiated with UV radiation exposure time 15, 30, 45, 60, 75 and 90 min and gamma radiation absorbed doses 0.3, 0.6, 0.9, 1.2, 2, 3 and 4 kGy in combination with with H₂O₂. There was a clear difference observed for aqueous solution before and after treatment with reference to cytotoxicity and mutagenicity. In Allium cepa test, a 47.07, 44.36 and 38.23% increase in root length (RL), root count (RC) and mitotic index (MI) was observed, respectively, for UV/H₂O₂ treatment and in the case of gamma/H₂O₂ treatment, the RL, RC and MI were increased up to 49.39, 52.63 and 52.38%, respectively. Brine shrimp test has shown 85.95 and 91.30% decrease in toxicity using UV/H₂O₂ and gamma/H₂O₂ respectively, while hemolytic test has shown 19.21 and 26.32% hemolysis using UV/H₂O₂ and gamma/H₂O₂, respectively. The mutagenicity reduced up to 82.3, 86.46 and 89.59% (TA98) and 85.42, 87.5 and 90.63% (TA100) for UV/H₂O₂ while 89.59, 90.63 and 93.75% (TA98) and 84.38, 89.59 and 92.71% (TA100) for gamma/H₂O₂. The UV and gamma radiation along with H₂O₂ based AOPs are promising approaches to detoxify the wastewater which can be extended to real hospital liquid effluent effectively.

Kinetic and equilibrium study of (poly amido amine) PAMAM dendrimers for the removal of chromium from tannery wastewater

Water gets polluted by industrial effluents, mainly composed of heavy metals and organic materials. Water soluble heavy metals can be taken up by living organisms. Chromium mainly occurs in the form of chromate and cationic hydroxo complexes in water. Apart from conventional methods of heavy metal removal, there are some novel approaches such as using dendrimers for removal of heavy metal. Dendrimers are extremely branched nano sized polymers with a three-dimensional symmetry around a core that imparts poly functionality. PAMAM (poly amido amine) dendrimers having ethylene diamine as core and methyl acrylate as repeating unit was divergently synthesized. Characterization of PAMAM dendrimers was evaluated by UV–Vis spectroscopy, zeta sizer, scanning electron microscopy (SEM) and Fourier-transform infrared (FT-IR) spectroscopy. Zero generation dendrimers have amine terminal groups, showed intense amide group peak at 1596.76 cm−1. The λ max value was 278 nm. SEM exhibited spherical shape for full generation while needle like structure for −0.5 generation. Evaluation of chromium removal from wastewater has been done by atomic absorption spectroscopy (AAS). The data revealed that optimal removal of Cr occurs at dendrimer concentration of 5 mL, Cr concentration of 300 ppm, contact time of 2 min and pH 7. The synthesized dendrimers have effectively removed Cr from tannery wastewater.

Experimental modeling, optimization and comparison of coagulants for removal of metallic pollutants from wastewater

Wastewater treatment coagulation is one of the most important physicochemical operations used in industry. The adsorption capability of marigold leaf powder, tea waste and ferrous sulfate was investigated for domestic and tannery effluents. These adsorbents significantly affected the pH, electrical conductivity (EC) and turbidity of wastewater. Maximum decrease in all the attributes was observed for 10 g of adsorbents application. All the adsorbents significantly affected the physiochemical attributes of both wastewaters. Similarly, maximum adsorption potential was observed in case of tea waste powder. Maximum decrease in all physiochemical attributes such as pH (15%), EC (21%), turbidity (54%), total dissolved solids (TDS; 36%), total suspended solids (TSS; 43%), total hardness (TH; 52%), chloride contents (59%) and phosphate contents (60%) was observed with the application of 10 g of tea waste. Regarding the heavy metals, maximum decrease for cadmium (Cd; 47%), lead (Pb; 81%), arsenic (As; 44%), copper (Cu; 75%), iron (Fe; 49%), chromium (Cr; 68%) and zinc (Zn; 64%) was observed in same treatment. The decreasing order in terms of their adsorption potential for coagulants was tea waste > marigold leaf powder > ferrous sulfate. However, for the wastewater, the maximum effect of adsorbents was observed in case of domestic wastewater as compared to the tannery water. Based on these data, it is suggested that tea waste has maximum adsorption potential for the remediation of wastewater.

Coagulation of Metallic Pollutants from Wastewater Using a Variety of Coagulants Based on Metal Binding Interaction Studies

In this study, different organic (moringa and neem leaf powder) and inorganic (alum) coagulants were used for the wastewater treatment. Results revealed that all the coagulants at various doses significantly affected the pH, electrical conductivity (EC) and turbidity of wastewater. The maximum decrease in all the attributes was observed when 10 g of coagulants were used. Similarly, maximum adsorption potential was observed in case of moringa leaf powder. Maximum decrease in all physiochemical attributes such as pH (13%), EC (65%), turbidity (75%), total dissolved solids (TDS; 51%), total suspended solids (TSS; 48%), total hardness (TH; 29%), chloride contents (66%) and phosphate contents (44%) was observed. Regarding the heavy metals, maximum decrease for Cadmium (Cd; 96%), Lead (Pb; 88%), Arsenic (As; 23%), Iron (Fe; 90%), Manganese (Mn; 96%) and Zinc (Zn; 48%) was observed in same treatment. The decreasing order in terms of their adsorption potential for coagulants was moringa leaf powder > Alum > neem leaf powder. However, the maximum effect of coagulants was observed in case of textile wastewater as compared to the hospital wastewater. Based on the analyses, it is concluded that the moringa leaf powder has maximum adsorption potential for the remediation of wastewater.

Sol–Gel Synthesis of Mesoporous Silica–Iron Composite: Kinetics, Equilibrium and Thermodynamics Studies for the Adsorption of Turquoise-Blue X-GB Dye

Mesoporous silica (MPS) and MPS-Fe composite was prepared via sol–gel technique and characterized by BET, FTIR, XRD, SEM and pZc. The MPS and MPS-Fe adsorption efficiencies were evaluated for a cationic dye Turquoise-blue X-GB. The MPS-Fe composite showed pore size and BET values of 9.52 nm and 309 m2/g, respectively. XRD and SEM analysis revealed the amorphous nature and uniform distribution of spherical partciles with average particle size of 50 nm of MPS-Fe composite. The points of zero (pZc) charge found to be 2.3 and 6.3 for MPS and MPS-Fe, respectively. The MPS and MPS-Fe showed promising efficiency for the adsorption of Turquoise-blue X-GB as a function of medium pH, contact time, dye initial concentration and temperature. Among, Freundlich, Langmuir, Harkins–Jura, Temkin, Doubinin–Radushkevich isotherms, the Turquoise-blue X-GB followed Langmuir isothermal model with adsorption capacities of 83.34 mg/g and 74.07 mg/g for MPS and MPS-Fe composite, respectively. Among kinetics models, pseudo second order kinetic model fitted to the dye adsorption with R2 values of 0.998 and 0.988 for MPS and MPS-Fe composite, respectively. The negative values of enthalpy (ΔH) and free energy (ΔG) revealed exothermic and spontaneous adsorption of dye at room temperature. Results revealed that MPS and MPS-Fe composite have promising potential for Turquoise-blue X-GB dye adsorption and could possibly be extended for the adsorption of dyes from textile effluents.