Determination of physical and chemical stability in pressurised metered dose inhalers: potential new techniques

In-vitro and in-vivo respiratory deposition of a developed metered dose inhaler formulation of an anti-migraine drug

Enhancement of zolmitriptan bioavailability through development of micronized zolmitriptan pressurized metered dose inhaler (MDI) as an alternative to its traditional drug delivery systems. A reversed phase HPLC method for zolmitriptan determination was developed and evaluated. Micronized zolmitriptan MDI formulations were prepared using two different propellants. The prepared formulations were evaluated for mean shot weight, drug content, and leakage rate in addition to in-vitro deposition using next generation impactor where mass median aerodynamic diameter (MMAD), geometric standard deviation (GSD), fine particle dose, fine particle fraction (FPF), emitted dose (ED), and dispersibility were determined. The selected formulation was evaluated for in-vivo bronchial absorption in rats. The physicochemical characters of the prepared formulations were found to be dependent mainly on the vapor pressure of the used propellant. MDI formulation prepared with HFA 134a propellant was found to have the lowest MMAD (3.47 ± 0.65) with GSD of 2.3 ± 0.4. It also had the highest FPF (41.9), ED (89.26 ± 2.35) with dispersibility of 46.9%. This formulation, when applied to rats, resulted in faster Tmax (27 ± 5 min) with higher Cmax (1236 ± 116 ng/mL) and AUC(0-12) (3375 ± 482 ng/mL·h) over the oral tablet. Its relative bioavailability was 72.7% which was 1.25 times higher than the oral tablet relative bioavailability. Zolmitriptan MDI formulation was developed using micronized zolmitriptan powder without further modification or particle engineering. The developed formulation using HFA 134a propellant could be favorable alternative, with enhanced bioavailability, to zolmitriptan oral tablet for acute migraine treatment.

Particle Surface Roughness Improves Colloidal Stability of Pressurized Pharmaceutical Suspensions

PURPOSE

The effects of particle size and particle surface roughness on the colloidal stability of pressurized pharmaceutical suspensions were investigated using monodisperse spray-dried particles.

METHODS

The colloidal stability of multiple suspensions in the propellant HFA227ea was characterized using a shadowgraphic imaging technique and quantitatively compared using an instability index. Model suspensions of monodisperse spray-dried trehalose particles of narrow distributions (GSD < 1.2) and different sizes (MMAD = 5.98 μm, 10.1 μm, 15.5 μm) were measured first to study the dependence of colloidal stability on particle size. Particles with different surface rugosity were then designed by adding different fractions of trileucine, a shell former, and their suspension stability measured to further study the effects of surface roughness on the colloidal stability of pressurized suspensions.

RESULTS

The colloidal stability significantly improved (p < 0.001) from the suspension with 15.5 μm-particles to the suspension with 5.98 μm-particles as quantified by the decreased instability index from 0.63 ± 0.04 to 0.07 ± 0.01, demonstrating a strongly size-dependent colloidal stability. No significant improvement of suspension stability (p > 0.1) was observed at low trileucine fraction at 0.4 % where particles remained relatively smooth until the surface rugosity of the particles was improved by the higher trileucine fractions at 1.0 % and 5.0 %, which was indicated by the substantially decreased instability index from 0.27 ± 0.02 for the suspensions with trehalose model particles to 0.18 ± 0.01 (p < 0.01) and 0.03 ± 0.01 (p < 0.002) respectively.

CONCLUSIONS

Surface modification of particles by adding shell formers like trileucine to the feed solutions of spray drying was demonstrated to be a promising method of improving the colloidal stability of pharmaceutical suspensions in pressurized metered dose inhalers.

Characterization of the suspension stability of pharmaceuticals using a shadowgraphic imaging method

A new shadowgraphic imaging method and an associated instrument for analyzing the physical stability of pharmaceutical suspensions are introduced in this paper. The new suspension tester consists mainly of a high-resolution camera that takes sequential shadowgraphic images of emulsions or suspensions and a 2D collimated LED for simultaneous whole-sample illumination in bright field. A built-in ultrasonic bath provides controlled initial agitation to the samples of interest. Sequential images acquired by the experimental setup were used to derive normalized transmission profiles from which an instability index was developed for quantitative stability comparison between samples. Instrument performance was verified by measuring the stability of a series of oil-in-water emulsions prepared with surfactant mixtures of different ratios. The new instrument correctly determined the required hydrophilic-lipophilic balance for sunflower oil to be 7.0. The stability of a pressurized suspension of spray dried lipid (DSPC) particles was monitored for 5 days after propellant filling. Although stable for the first 24 h, the lipid suspension was found to decrease in stability from day 1 to day 4. Morphological and spectroscopic analysis revealed that the suspended DSPC particles had reformed into large thin sheets of lipid, thereby causing the gradual stability decrease during the aging study. The effects of initial agitation on the stability of suspensions were demonstrated by agitating a suspension of micronized fluticasone propionate in propellant using a wrist action shaker and an ultrasonic bath respectively. A significant improvement of suspension stability was achieved by replacing the wrist action shaker method with ultrasonic agitation. Simultaneous illumination of the complete suspension, a high image acquisition rate, and controlled initial agitation are features that make this new suspension tester a suitable and more reliable instrument for investigating the stability of pressurized pharmaceutical suspensions.

Enhancing Stability of Exenatide-Containing Pressurized Metered-Dose Inhaler Via Reverse Microemulsion System

The dispersibility and stability issues of peptide drugs during preparation and storage hinder the widespread adoption of pressurized metered-dose inhaler (pMDI). This study aimed to develop a reverse microemulsion (RM) of exenatide (EXE) pMDI through a liquid-based bottom-up method, thus to overcome the stability issue of peptide drugs encountered in traditional top-down methods, such as milling down and high-pressure homogenization. In this study, Pluronic® L64 (L64) was chosen as a surfactant to prepare the EXE-RM pMDI formulations with the assistance of ethanol. The results showed RM possessed a particle size of 123.80 ± 2.91 nm with 0.121 ± 0.024 PdI and a satisfied fine-particle fraction of 41.30 ± 3.73% measured by a next-generation impactor. In addition, the dispersion stability of RM pMDI was maintained after storage at 4 °C for 50 days. The secondary structure of EXE was maintained during the preparation process. Moreover, the results indicated that L64 was compatible with cells and could improve the penetration of EXE through cell monolayers. Through the liquid-based bottom-up method, EXE-RM pMDI was successfully prepared and exhibited favorable stability and aerodynamic performance. This study offers a preparation strategy to enhance the stability of peptides in pMDIs.