Synthesis and Characterization of CeO2/CuO Nanocomposites for Photocatalytic Degradation of Methylene Blue in Visible Light

e-Beam and γ-rays Induced Synthesis and Catalytic Properties of Copper Nanoclusters-Deposited Composite Track-Etched Membranes

Effective removal of toxic inorganic and organic pollutants is one of the current leading challenges of wastewater treatment. In this study, the decomposition of methylene blue (MB) under UV light irradiation was investigated in the presence of copper nanoclusters (NCs)-deposited polyethylene terephthalate (PET) track-etched hybrid membranes. PET track-etched membranes (TeMs) with an average pore size of ~400 nm were grafted by functional acrylic acid (AA) monomer under electron beam irradiation after oxidation with H₂O₂/UV system. The radiation dose varied between 46 and 200 kGy. For the deposition of copper NCs, poly(acrylic acid) (PAA)-grafted membranes saturated with Cu(II) ions were irradiated either by electron beam or γ-rays to obtain copper-based NCs for the catalytic degradation of MB. Irradiation to 100 kGy with accelerated electrons resulted in the formation of small and uniform copper hydroxide (Cu(OH)₂) nanoparticles homogeneously distributed over the entire volume of the template. On the other hand, irradiation under γ-rays yielded composites with copper NCs with a high degree of crystallinity. However, the size of the deposited NCs obtained by γ-irradiation was not uniform. Nanoparticles with the highest uniformity were obtained at 150 kGy dose. Detailed analysis by X-ray diffraction (XRD) and scanning electron microscopy (SEM) confirmed the loading of copper nanoparticles with an average size of 100 nm on the inner walls of nanochannels and on the surface of PET TeMs. Under UV light irradiation, composite membranes loaded with NCs exhibited high photocatalytic activity. It was determined that the highest catalytic activity was observed in the presence of Cu(OH)₂@PET-g-PAA membrane obtained at 250 kGy. More than 91.9% of the initial dye was degraded when this hybrid membrane was employed for 180 min, while only 83.9% of MB was degraded under UV light using Cu@PET-g-PAA membrane. Cu(OH)₂@PET-g-PAA membranes obtained under electron beam irradiation demonstrated a higher photocatalytic activity compared to Cu@PET-g-PAA membranes attained by γ-rays.

Bandgap engineering approach for designing CuO/Mn3O4/CeO2 heterojunction as a novel photocatalyst for AOP-assisted degradation of Malachite green dye

A ternary nanohybrid CuO/Mn₃O₄/CeO₂ was developed in the present work using a co-precipitation-assisted hydrothermal method. The designed photocatalyst's structural, morphology, elemental composition, electronic states of elements, and optical properties were studied using corresponding analytical techniques. Results from PXRD, TEM/HRTEM, XPS, EDAX, and PL showed that the desired nanostructure had formed. Using Tauc's energy band gap plot, it was determined that the nanostructures band gap was ~ 2.44 eV, which showed the band margins of the various moieties, CeO₂, Mn₃O₄, and CuO, had modified. Thus, improved redox conditions led to a substantial decrease in the recombination rate of electron-hole pairs, which was further explained by a PL study in that charge separation plays a key role. Under exposure to visible light irradiation for 60 min, it was revealed that the photocatalyst achieved 98.98% of photodegradation efficiency for malachite green (MG) dye. The process of photodegradation proceeded according to a pseudo-first-order reaction kinetic model with an excellent rate of reaction of 0.07295 min^-1 with R² = 0.99144. The impacts of different reaction variables, inorganic salts, and water matrices were investigated. This research seeks to create a ternary nanohybrid photocatalyst with high photostability, visible spectrum activity, and reusability up to four cycles.

Laser induced plant leaf extract mediated synthesis of CuO nanoparticles and its photocatalytic activity

Metal nanoparticles furnished by the green synthesis approach have exhibited fascinating attributes owing to their biocompatibility with biomolecules, and their rapid environmentally friendly synthesis. On copper oxide (CuO) nanoparticles, a laser induced bio reduction work has been accomplish using Centella asiatica aqueous extract at room temperature is the pioneer in the field. This synthesis technique is easy, fruitful, eco-friendly, and counterfeit for the size-tunable synthesis of diverse shapes of stable copper nanoparticles. UV-visible spectroscopy, Field Emission Scanning Electron Microscopy (FESEM), Fourier Transform Infrared Spectroscopy (FTIR), Energy - Dispersive X-ray Spectroscopy (EDX), X-ray diffraction (XRD) and photodegradation study have astounding properties of regulating the formation, crystalline nature, and morphology of an integrated specimen. Moreover, the obtained copper oxide nanoparticle has the tendency to decrease the absorbance maximum value of methylene blue because of the catalytic activity posed by these nanoparticles on the reduction of methylene blue by Centella asiatica. It has been studied and confirmed by UV-visible spectrophotometer, and it has been recognised as an electron relay effect.

Simple preparation of a CuO@γ-Al2O3 Fenton-like catalyst and its photocatalytic degradation function

We designed a photocatalyst and developed sustainable wastewater purification technology, which have significant advantages in effectively solving the global problem of drinking water shortage. In this study, a new nanocomposite was reported and shown to be a catalyst with excellent performance; CuO was coated successively onto functionalized nano γ-Al₂O₃, and this novel structure could provide abundant active sites. We evaluated the performance of the CuO@γ-Al₂O₃ nanocomposite catalyst for polyvinyl alcohol (PVA) degradation under visible light irradiation. Under optimized conditions (calcination temperature, 450 °C; mass ratio of γ-Al₂O₃:Cu(NO₃)₂·3H₂O, 1:15; pH value, 7; catalyst dosage, 2.6 g/L; reaction temperature, 20 °C; and H₂O₂ dosage, 0.2 g/mL), the CuO@γ-Al₂O₃ nanocomposite catalyst presented an excellent PVA removal rate of 99.21%. After ten consecutive degradation experiments, the catalyst could still maintain a PVA removal rate of 97.58%, thus demonstrating excellent reusability. This study provides an efficient and easy-to-prepare photocatalyst and proposes a mechanism for the synergistic effect of the photocatalytic reaction and the Fenton-like reaction.

Synthesis and Property Examination of Er2FeSbO7/BiTiSbO6 Heterojunction Composite Catalyst and Light-Catalyzed Retrogradation of Enrofloxacin in Pharmaceutical Waste Water under Visible Light Irradiation

A new photocatalyst, Er2FeSbO7, was prepared by solid phase sintering using the high-temperature synthesis method for the first time in this paper. Er2FeSbO7/BiTiSbO6 heterojunction (EBH) catalyst was prepared by the solvent thermal method for the first time. Er2FeSbO7 compound crystallized in the pyrochlore-type architecture and cubelike crystal system; the interspace group of Er2FeSbO7 was Fd3m and the crystal cellular parameter a of Er2FeSbO7 was 10.179902 Å. The band gap (BDG) width of Er2FeSbO7 was 1.88 eV. After visible light irradiation of 150 minutes (VLGI-150min) with EBH as a photocatalyst, the removal rate (RR) of enrofloxacin (ENR) concentration was 99.16%, and the total organic carbon (TOC) concentration RR was 94.96%. The power mechanics invariable k toward ENR consistency and visible light irradiation (VLGI) time with EBH as a photocatalyzer attained 0.02296 min−1. The power mechanics invariable k which was involved with TOC attained 0.01535 min−1. The experimental results showed that the photocatalytic degradation (PCD) of ENR within pharmaceutical waste water with EBH as a photocatalyzer under VLGI was in keeping with the single-order reactivity power mechanics. The RR of ENR with EBH as a photocatalyzer was 1.151 times, 1.269 times or 2.524 times that with Er2FeSbO7 as a photocatalyst, BiTiSbO6 as a photocatalyst, or N-doping TiO2 (N-TO) as a photocatalyst after VLGI-150min. The photocatalytic activity, which ranged from high to low among above four photocatalysts, was as follows: EBHP > Er2FeSbO7 > BiTiSbO6 > N-TO. After VLGI-150min toward three periods of the project with EBH as a photocatalyst, the RR of ENR attained 98.00%, 96.76% and 95.60%. The results showed that the stability of EBH was very high. With appending trapping agent, it could be proved that the oxidative capability for degrading ENR, which ranged from strong to weak among three oxidic radicals, was as follows: superoxide anion > hydroxyl radicals (HRS) > holes. This work provides a scientific basis for the research and oriented leader development of efficient heterojunction catalysts.

A Novel Low-Cost Bio-Sorbent Prepared from Crisp Persimmon Peel by Low-Temperature Pyrolysis for Adsorption of Organic Dyes

In order to properly reuse food waste and remove various contaminants from wastewater, the development of green, sustainable and clean technologies has demonstrated potential in the efficient inhibition of secondary pollution to the environment. In this study, an economical and green method was used to prepare biochar from crisp persimmon peel (CPP) using flash-vacuum pyrolysis at different temperatures (200–700 °C; referred to as CPP200–CPP700). CPP200 has high polarity, low aromaticity and high oxygen-containing functional groups that exhibit superior MB adsorption capabilities. CPP200 that was prepared at a relatively low temperature of 200 °C exhibited a high adsorption capacity of 59.72 mg/g toward methylene blue (MB), which was relatively higher than that for alizarin yellow R (4.05 mg/g) and neutral red (39.08 mg/g), indicating that CPP200 possesses a higher adsorption selectivity for cationic dyes. Kinetics investigation revealed that the kinetic data of CPP200 for the adsorption of MB was better fitted by a linear pseudo-second-order model. Isothermal studies indicated that the linear Langmuir model was more suitable for describing the adsorption process. The adsorption thermodynamics illustrated that the adsorption of MB onto CPP200 was spontaneous and endothermic. EDS and IR analyses of CPP200 for both pre- and post-adsorption of MB showed that electrostatic interactions between oxygen-containing groups on biochar and target MB dominated the adsorption procedure, in addition to hydrogen bonding interactions. Reusability tests confirmed the excellent regeneration characteristics of CPP200, indicating that CPP200 may be used as a green, sustainable, highly efficient and recyclable adsorbent for the selective removal of cationic organic dyes.

Ce3+/Ce4+-Doped ZrO2/CuO Nanocomposite for Enhanced Photocatalytic Degradation of Methylene Blue under Visible Light

In recent years, photocatalysis has been used as an environmentally friendly method for the degradation of organic pigments in water. In this study, Ce³⁺/Ce⁴⁺-doped ZrO₂/CuO as a mixed semiconductor oxide was successfully prepared by a one-step hydrothermal method. The Ce³⁺/Ce⁴⁺-doped ZrO₂/CuO has shown high degradation efficiency of methylene blue (MB), and the maximum degradation percentage was observed to be 94.5% at 180 min under irradiation visible light. The photocatalytic activity increases significantly by doping Ce³⁺/Ce⁴⁺ in ZrO₂/CuO for MB degradation. Ce³⁺/Ce⁴⁺ doping is shown to reduce the (e^-/h⁺) recombination rate and improve the charge transfer, leading to enhanced photocatalytic activity of materials. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), FTIR, EDS, BET and diffuse reflectance spectroscopy (DRS).

Development of novel K0.8Ni0.4Ti1.6O4 nano bamboo leaves, microstructural characterization, double absorption, and photocatalytic removal of organic pollutant

Novel K_0.8Ni_0.4Ti_1.6O₄ (KNTO) nano bamboo leaves were prepared for the first time under a simple hydrothermal method with 3 M KOH at 320 °C over 80 min. Highly pure KNTO possessing layered structure was determined by X-ray diffraction (XRD) and high-resolution transmission electron microscope (HRTEM). Double absorption feature of KNTO semiconductor was revealed at band energies of 1.88 and 2.08 eV by the UV-vis diffuse reflectance spectra and confirmed by the photoluminescence (PL) spectra. The photocatalytic activity was explored by the photodegradation of MB organic dye. KNTO not only exhibits strong adsorptive ability on methylene blue (MB) in dark environment, but also possesses good photodegradation capability of 94% degradation in 60 min. Degradation mechanism revealed that the photogenerated holes play an essential role in the MB degradation process, which is confirmed by trapping experiments. The recycling experiments demonstrated very high recycling ability and durability of KNTO nano bamboo leaves, suggesting KNTO is a potential candidate for high efficiency organic pollutant removal in the wastewater treatment.

Enhanced sunlight photocatalytic activity and biosafety of marine-driven synthesized cerium oxide nanoparticles

This contribution presents the biosynthesis, physiochemical properties, toxicity and photocatalytic activity of biogenic CeO₂ NPs using, for the first time, marine oyster extract as an effective and rich source of bioreducing and capping/stabilizing agents in a one-pot recipe. CeO₂ NPs formation was initially confirmed through the color change from light green to pale yellow and subsequently, their corresponding absorption peak was spectroscopically determined at 310 nm with an optical band-gap of 4.67 eV using the DR-UV technique. Further, XRD and Raman analyses indicated that nanoceria possessed face-centered cubic arrangements without any impurities, having an average crystallite size of 10 nm. TEM and SEM results revealed that biogenic CeO₂ NPs was approximately spherical in shape with a median particle size of 15 ± 1 nm. The presence of various bioorganic substances on the surface of nanoparticles was deduced by FTIR and TGA results. It is found that marine-based nanoceria shows no cytotoxic effect on the normal cell, thus indicating their enhanced biocompatibility and biosafety to living organisms. Environmentally, due to energy band gap, visible light-activated CeO₂ nanocatalyst revealed superior photocatalytic performance on degradation of methylene blue pollutant with removal rate of 99%. Owing to the simplicity, cost-effectiveness, and environmentally friendly nature, this novel marine biosynthetic route paves the way for prospective applications of nanoparticles in various areas.