1
|
Macías J, Frade JR, Yaremchenko AA. SrTiO 3-SrVO 3 Ceramics for Solid Oxide Fuel Cell Anodes: A Route from Oxidized Precursors. MATERIALS (BASEL, SWITZERLAND) 2023; 16:7638. [PMID: 38138780 PMCID: PMC10744890 DOI: 10.3390/ma16247638] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/20/2023] [Revised: 12/10/2023] [Accepted: 12/11/2023] [Indexed: 12/24/2023]
Abstract
Perovskite-type Sr(Ti,V)O3-δ ceramics are promising anode materials for natural gas- and biogas-fueled solid oxide fuel cells, but the instability of these phases under oxidizing conditions complicates their practical application. The present work explores approaches to the fabrication of strontium titanate-vanadate electrodes from oxidized precursors. Porous ceramics with the nominal composition SrTi1-yVyOz (y = 0.1-0.3) were prepared in air via a solid state reaction route. Thermal processing at temperatures not exceeding 1100 °C yielded composite ceramics comprising perovskite-type SrTiO3, pyrovanadate Sr2V2O7 and orthovanadate Sr3(VO4)2 phases, while increasing firing temperatures to 1250-1440 °C enabled the formation of SrTi1-yVyO3 perovskites. Vanadium was found to substitute into the titanium sublattice predominantly as V4+, even under oxidizing conditions at elevated temperatures. Both perovskite and composite oxidized ceramics exhibit moderate thermal expansion coefficients in air, 11.1-12.1 ppm/K at 30-1000 °C, and insignificant dimensional changes induced by reduction in a 10%H2-N2 atmosphere. The electrical conductivity of reduced perovskite samples remains comparatively low, ~10-1 S/cm at 900 °C, whereas the transformation of oxidized vanadate phases into high-conducting SrVO3-δ perovskites upon reduction results in enhancement in conductivity, which reaches ~3 S/cm at 900 °C in porous composite ceramics with nominal composition SrTi0.7V0.3Oz. The electrical performance of the composite is expected to be further improved by optimization of the processing route and microstructure to facilitate the reduction of the oxidized precursor and attain better percolation of the SrVO3 phase.
Collapse
Affiliation(s)
| | | | - Aleksey A. Yaremchenko
- CICECO—Aveiro Institute of Materials, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro, Portugal; (J.M.); (J.R.F.)
| |
Collapse
|
2
|
Patella B, Zanca C, Ganci F, Carbone S, Bonafede F, Aiello G, Miceli R, Pellitteri F, Mandin P, Inguanta R. Pd-Co-Based Electrodes for Hydrogen Production by Water Splitting in Acidic Media. MATERIALS (BASEL, SWITZERLAND) 2023; 16:474. [PMID: 36676217 PMCID: PMC9864770 DOI: 10.3390/ma16020474] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 08/18/2022] [Revised: 11/15/2022] [Accepted: 12/22/2022] [Indexed: 06/17/2023]
Abstract
To realize the benefits of a hydrogen economy, hydrogen must be produced cleanly, efficiently and affordably from renewable resources and, preferentially, close to the end-users. The goal is a sustainable cycle of hydrogen production and use: in the first stage of the cycle, hydrogen is produced from renewable resources and then used to feed a fuel cell. This cycle produces no pollution and no greenhouse gases. In this context, the development of electrolyzers producing high-purity hydrogen with a high efficiency and low cost is of great importance. Electrode materials play a fundamental role in influencing electrolyzer performances; consequently, in recent years considerable efforts have been made to obtain highly efficient and inexpensive catalyst materials. To reach both goals, we have developed electrodes based on Pd-Co alloys to be potentially used in the PEMEL electrolyzer. In fact, the Pd-Co alloy is a valid alternative to Pt for hydrogen evolution. The alloys were electrodeposited using two different types of support: carbon paper, to fabricate a porous structure, and anodic alumina membrane, to obtain regular arrays of nanowires. The goal was to obtain electrodes with very large active surface areas and a small amount of material. The research demonstrates that the electrochemical method is an ideal technique to obtain materials with good performances for the hydrogen evolution reaction. The Pd-Co alloy composition can be controlled by adjusting electrodeposition parameters (bath composition, current density and deposition time). The main results concerning the fabrication process and the characterization are presented and the performance in acid conditions is discussed.
Collapse
Affiliation(s)
- Bernardo Patella
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Claudio Zanca
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Fabrizio Ganci
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
- Corpo Nazione dei Vigili del Fuoco, 41126 Rome, Italy
| | - Sonia Carbone
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Francesco Bonafede
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Giuseppe Aiello
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Rosario Miceli
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Filippo Pellitteri
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| | - Philippe Mandin
- IRDL UMR CNRS 6027, Université de Bretagne Sud, 56100 Lorient, France
| | - Rosalinda Inguanta
- Dipartimento di Ingegneria, Università degli Studi di Palermo, 90128 Palermo, Italy
| |
Collapse
|