Bio-based Films from Linter Cellulose and Its Acetates: Formation and Properties

Cellulose esters: Synthesis for further formation of films with magnetite nanoparticles incorporated

This study investigated the homogeneous synthesis of cellulose acetate (CA) and propionate (CP) with varying degrees of substitution (DS) from sisal cellulose in a N, N-dimethylacetamide/lithium chloride (DMAc/LiCl) solvent system. These esters were used to prepare neat (CADSF/CPDSF) and nanocomposite films (CADSFFe/CPDSFFe) from prior synthesized magnetite nanoparticles (NPs, Fe3O4, 5.1 ± 0.5 nm). Among the CA and CP series, the composite CA0.7FFe and the neat CP0.7F films exhibited the highest modulus of elasticity, 2105 MPa and 2768 MPa, respectively, probably a consequence of the continuous fibrous structures present on the surface of these films. Microsphere formation on the film's surface was observed in scanning electron microscopy micrographs. This points to applications in the controlled release of targeted substances. The VSM analysis showed that the cellulosic matrices preserved the superparamagnetic characteristics of the NPs. This study suggested a reduced coupling effect between nanoparticles inside polymeric films due to magnetic saturation at low fields. CA0.7FFe and CA1.3FFe composite films reached a saturation magnetization (MSAT) of 46 emu/g around 7 kOe field. Hosting magnetite nanoparticles in cellulose ester matrices may be an interesting way to develop new functional cellulose-based materials, which have the potential for diverse applications, including microelectromechanical systems and microsensors.

Review of Bacterial Nanocellulose-Based Electrochemical Biosensors: Functionalization, Challenges, and Future Perspectives

Electrochemical biosensing devices are known for their simple operational procedures, low fabrication cost, and suitable real-time detection. Despite these advantages, they have shown some limitations in the immobilization of biochemicals. The development of alternative materials to overcome these drawbacks has attracted significant attention. Nanocellulose-based materials have revealed valuable features due to their capacity for the immobilization of biomolecules, structural flexibility, and biocompatibility. Bacterial nanocellulose (BNC) has gained a promising role as an alternative to antifouling surfaces. To widen its applicability as a biosensing device, BNC may form part of the supports for the immobilization of specific materials. The possibilities of modification methods and in situ and ex situ functionalization enable new BNC properties. With the new insights into nanoscale studies, we expect that many biosensors currently based on plastic, glass, or paper platforms will rely on renewable platforms, especially BNC ones. Moreover, substrates based on BNC seem to have paved the way for the development of sensing platforms with minimally invasive approaches, such as wearable devices, due to their mechanical flexibility and biocompatibility.

Preparation and Characterization of Chinese Leek Extract Incorporated Cellulose Composite Films

This study aimed to prepare microcrystalline cellulose (MCC) films with good mechanical properties via plasticization using a Chinese leek (CL, Allium tuberosum) extract. The microstructure, crystal structure, mechanical properties, barrier ability, and thermal properties of the films were investigated. The chemical structure analysis of CL extract showed the existence of cellulose, lignin, and low-molecular-weight substances, such as polysaccharides, pectins, and waxes, which could act as plasticizers to enhance the properties of MCC:CL biocomposite films. The results of scanning electron microscopy and atomic force microscopy analyses indicated the good compatibility between MCC and CL extract. When the volume ratio of MCC:CL was 7:3, the MCC:CL biocomposite film exhibited the best comprehensive performance in terms of water vapor permeability (2.11 × 10^-10 g/m·s·Pa), elongation at break (13.2 ± 1.8%), and tensile strength (24.7 ± 2.5 MPa). The results of a UV absorption analysis demonstrated that the addition of CL extract improved the UV-shielding performance of the films. Therefore, this work not only proposes a facile method to prepare MCC films with excellent mechanical properties via plasticization using CL extract but also broadens the potential applications of MCC films in the packaging area.

Thermoplastic "All-Cellulose" Composites with Covalently Attached Carbonized Cellulose

Thermoplastic "all-cellulose" composites were synthesized by covalent functionalization of cellulose acetate (CA) with oxidized carbonized cellulose (OCC). The OCC were manufactured via microwave-assisted hydrothermal carbonization (HTC) of cellulose followed by oxidation and dialysis. The OCC were of micrometer-size, had plane morphology and contained a variety of oxygen functionalities, enabling transformation into acyl chlorinated OCC under moderate reaction conditions. The synthesis of OCC-modified CA composites and neat CA were performed in the recyclable ionic liquid 1-allyl-3-methylimidazolium chloride. The degree of acetylation and amount of OCC were varied to establish their influence on thermal and physical properties of the composites. The OCC-modified CA composites displayed a notably enhanced film-forming ability, which led to improved optical and mechanical properties compared to neat CA. In addition, it was shown that OCC-modified CA composites can be synthesized from waste products, such as paper tissues. The OCC-modification was demonstrated to be a promising route to transparent and strong thermoplastic "all-cellulose" composites with moderate flexibility.

Synthesis and Characterizations of a Collagen-Rich Biomembrane with Potential for Tissue-Guided Regeneration

Objectives  In this study, a collagen-rich biomembrane obtained from porcine ­intestinal submucosa for application in guided bone regeneration was developed and characterized. Then, its biological and mechanical properties were compared with that of commercial products ( GenDerm [Baumer], Lumina-Coat [Critéria], Surgitime PTFE [Bionnovation], and Surgidry Dental F [Technodry]).

Materials and Methods  The biomembrane was extracted from porcine intestinal submucosa. Scanning electron microscopy, spectroscopic dispersive energy, glycosaminoglycan quantification, and confocal microscopy by intrinsic fluorescence were used to evaluate the collagen structural patterns of the biomembrane. Mechanical tensile and deformation tests were also performed.

Statistical Analysis   The results of the methods used for experimental membrane characterizations were compared with that obtained by the commercial membranes and statistically analyzed (significance of 5%).

Results  The collagen-rich biomembrane developed also exhibited a more organized, less porous collagen fibril network, with the presence of glycosaminoglycans. The experimental biomembrane exhibited mechanical properties, tensile strength, and deformation behavior with improved average stress/strain when compared with other commercial membranes tested. Benefits also include a structured, flexible, and ­bioresorbable characteristics scaffold.

Conclusions  The experimental collagen-rich membrane developed presents physical–chemical, molecular, and mechanical characteristics similar to or better than that of the commercial products tested, possibly allowing it to actively participating in the process of bone neoformation.

Influence of Natural Fillers on Thermal and Mechanical Properties and Surface Morphology of Cellulose Acetate-Based Biocomposites

In the present study, the influence of adding natural fillers to a cellulose acetate (CA) matrix, in order to develop biocomposites, on the properties of the achieved materials has been investigated. Extracted wood flour, holocellulose, and alpha cellulose were used as appropriate fillers. The results of the thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) of the fillers and biocomposites suggested the importance of the degree of degradation of filler properties, induced by the chemical treatment necessary for the preparation of the fillers, with emphasis on the content of lignin and the degradation of cellulose. Scanning electron microscopy (SEM) and mechanical analysis revealed that the matrix-filler ratio had a major effect on the prepared CA-based biocomposites, since polarity differences between the two major components caused the reduction of attractive forces in the matrix-filler relation, subsequently altering the properties of the developed materials.

Cellulose acetate fibers prepared from different raw materials with rapid synthesis method

Transesterification is a mild process to prepare cellulose acetate (CA) as compared with the traditional method. In this study, CA fibers were produced from six cellulose raw materials based on a simple and rapid transesterification method. The properties of the CA solutions and the obtained CA fibers were investigated in detail. Results showed that all of the cellulose raw materials were esterified within 15 min, and spinning dopes could be obtained by concentrating the CA solutions via vacuum distillation. The XRD, FT-IR, (1)H, (13)C and HSQC NMR analysis confirmed the successful synthesis of CA. The degree of substitution (DS) of the obtained CA was significantly affected by the degree of polymerization (DP) of cellulose raw materials, which further influenced the viscosity of CA solutions as well as the structural, thermal and mechanical properties of the CA fibers.

Supporting materials that improve the stability of enzyme membranes

Long-term stability is a key property of enzyme membranes that can be used for biosensors, bioreactors, and bio-fuel cells. This review discusses factors that decrease the stability, and provides two examples of enzyme membranes, a polyion complex membrane and a cellulose membrane, with which stability loss can be avoided. By using these materials, long-term stability was improved. These supporting materials could be applied to construct biosensors, bioreactors, and bio-fuel cells.

Per-O-acetylation of cellulose in dimethyl sulfoxide with catalyzed transesterification

Cellulose acetylation was investigated in dimethyl sulfoxide (DMSO) with isopropenyl acetate (IPA) as acetylating reagent and 1,8-diazabicyclo[5,4,0]undec-7-ene (DBU) as catalyst at 70-130 °C for 3-12 h. The degree of substitution (DS) of acetylated cellulose was comparatively determined by titration and ¹H NMR and confirmed by FT-IR analysis. The results indicated that per-O-acetylation was achieved at >90 °C for a relatively long duration. The three well-resolved peaks of carbonyl carbons in ¹³C NMR spectra also provided evidence of per-O-acetylation. The solubility of cellulose acetates in common organic solvents was examined, and the result showed that chloroform can be an alternative choice as a solvent for fully acetylated cellulose formed in this study besides DMSO. The intrinsic viscosity of acetylated cellulose solution implied almost no degradation of cellulose during acetylation in DMSO except at higher temperature (130 °C) for a long time.