Mechanical Properties of Animal Tendons: A Review and Comparative Study for the Identification of the Most Suitable Human Tendon Surrogates

Evaluating barbed sutures: A porcine biomechanical comparison of Z-plasty and turndown flap according to Silfverskiöld

Introduction

It is not possible to add an infinite amount of suture material to tendon plasties and repairs in vivo. Each additional knot can reduce the tensile strength by up to 50 %. Therefore, barbed sutures, as a knotless suturing system, should be investigated as a potential alternative to traditional sutures to minimize knot-related weakening.

Material and methods

Superficial porcine flexors were randomized into five groups. A non-contact measurement was utilized. The Z-plasty and the turndown flap according to Silfverskiöld were used. The Stratafix barbed knotless suture was compared to regular smooth polydioxanone. The biomechanical protocol included a creep test, a cyclic test, and a tear-off test.

Results

The Z-plasty with Stratafix showed significantly improved maximum force compared to the Z-plasty with Polydioxanon (PDS 108.5 ± 22.2N, Stratafix 142.3 ± 23.5N, p < .01). The Z-plasty was significantly superior to the turndown flap in maximum Force (turndownflap with Stratafix 52.4 ± 14.6N, Z-plasty with Stratafix 108.5 ± 22.2N, p < .001).

Conclusion

The Stratafix barbed suture can significantly improve the Z-plasty in maximum tension by up to 32 % when compared to regular PDS. To formulate a more precise indication, biological factors must be further investigated.

Understanding the structure and mechanics of the sheep calcaneal enthesis: a relevant animal model to design scaffolds for tissue engineering applications

Tendon or enthesis injuries are a worldwide clinical problem. Along the enthesis, collagen fibrils show a progressive loss of anisotropy and an increase in mineralization reaching the bone. This causes gradients of mechanical properties. The design of scaffolds to regenerate these load-bearing tissues requires validation in vivo in relevant large animal models. The sheep tendon of triceps surae muscle is an optimal animal model for this scope with limited knowledge about its structure and mechanics. We decided to investigate in-depth its structure and full-field mechanics. Collagen fibrils morphology was investigated via scanning electron microscopy revealing a marked change in orientation/dimensions passing from the tendon to the enthesis. Backscatter electron images and nanoindentation at the enthesis/bone marked small gradients of mineralization at the mineralized fibrocartilage reaching 27%wt and indentation modulus around 17-30 GPa. The trabecular bone instead had indentation modulus around 15-22 GPa. Mechanical tensile tests with digital image correlation confirmed the typical non-linear behavior of tendons (failure strain = 8.2 ± 1.0 %; failure force = 1369 ± 187 N) with maximum principal strains reaching mean values of εp1 ∼ 7 %. The typical auxetic behavior of tendon was highlighted by the minimum principal strains (εp2 ∼ 5 %), progressively dampened at the enthesis. Histology revealed that this behavior was caused by a local thickening of the epitenon. Cyclic tests showed a force loss of 21 ± 7 % at the last cycle. These findings will be fundamental for biofabrication and clinicians interested in designing the new generation of scaffolds for enthesis regeneration.

Comparative mechanical and elastic properties of the dorsal and ventral tendons in the peduncle of harbor porpoise (Phocoena phocoena)

Cetaceans swim via vertical movements of the tail. The tendons located in the caudal peduncle are attached to the caudal vertebrae to generate propulsive oscillations. Arguments have centered on whether the upstrokes and downstrokes of the tail and propulsive flukes are symmetrical or asymmetrical in time. Previous research from kinematics of swimming animals, muscle architecture and histology has supported both conditions. However, the composition and structure of the tendons suggest a potential mechanism to evaluate this disparity. In this study, the tendons of the caudal peduncle of the harbor porpoise (Phocoena phocoena) - specifically, the extensor caudae medialis (ECM) and the extensor caudae lateralis (ECL) from the epaxial muscle, and the medial hypaxialis lumborum (MHL) from the hypaxial muscle - were mechanically tested. Ramp to failure was performed on isolated tendon fascicles. Stress relaxation tests to 3% strain were also performed on fascicles. Polarized light microscopy was used to visualize the fibril crimp as tensile forces were applied to fascicles. Uncrimping of isolated fascicles was visualized at mean strain values between 0.031% and 0.048%. The maximum elastic moduli of fascicles taken to failure were between 1039.5 and 1185.8 MPa. No differences were found in the mechanical performance of the fascicles of the epaxial and hypaxial tendons. The mechanical properties of peduncle fascicles suggest a symmetrical stroke cycle for swimming by the porpoise.

Effect of Compressive Strain Rates on Viscoelasticity and Water Content in Intact Porcine Stomach Wall Tissues

Laparoscopic staplers are used extensively to seal and transect tissue. These devices compress tissue between the stapler jaws to achieve a desired compressed tissue thickness in preparation for stapling. The extent and rate of compression are dependent on surgeon technique, tissue characteristics, and stapler type, all of which can impact stapling outcomes such as bleeding, staple line leaks, and tissue healing. Historically, surgeons have relied on their experience, training, and tactile feedback from the device to optimize stapling. In recent years, the transition to electromechanical and robotic staplers has greatly impacted the tactile feedback available to the surgeon. This raises new questions about the optimal rates of tissue compression and the resultant tissue forces. This study quantifies the transmural biomechanics of the porcine stomach wall. Multirate indentation tests were used to observe the effects of indentation rate on the viscoelastic behavior of the stomach tissue during indentation, stress relaxation, and unconstrained recovery. Results show that the stomach wall demonstrates higher stress relaxation (88% versus 80%) and greater strain recovery (52% versus 47%) when indented at high rates (37.5%/s) versus slow rates (7.5%/s). Additionally, water content analysis was used to study fluid flow away from indented regions. Unindented regions were found to have greater water content compared to indented regions (78% compared to 75%). This data generated in this study may be used to enable the development of constitutive models of stomach tissue, which in turn may inform the control algorithms that drive compressive surgical devices.

3D Printing of a Biomimetic Myotendinous Junction Assisted by Artificial Intelligence

The myotendinous junction (MTJ) facilitates force transmission between muscle and tendon to produce joint movement. The complex microarchitecture and regional mechanical heterogeneity of the myotendinous junction pose major challenges in creating this interface in vitro. Engineering this junction in vitro is challenging due to substantial fabrication difficulties in creating scaffolds with intricate microarchitecture and stiffness heterogeneity to mimic the native muscle-tendon interface. To address the current challenges in creating the MTJ in vitro, digital light processing (DLP)-based 3D printing was used to fabricate poly(glycerol sebacate)acrylate (PGSA)-based muscle-tendon scaffolds with physiologically informed microstructure and mechanical properties. Local mechanical properties in various regions of the scaffold were tuned by adjusting the exposure time and light intensity used during the continuous DLP-based 3D printing process to match the mechanical properties present in distinct regions of native muscle-tendon tissue using printing parameters defined by an artificial intelligence-trained algorithm. To evaluate how the presence of zonal stiffness regions can affect the phenotype of a 3D-printed MTJ in vitro model, three 3D-printed PGSA-based scaffold conditions were investigated: (1) a scaffold with muscle-informed mechanical properties in its entirety without zonal stiffness regions, (2) a scaffold with one end possessing native muscle stiffness and the other end possessing native tendon stiffness, and (3) a scaffold with three distinct regions whose stiffness values correspond to those of muscle on one end of the scaffold, MTJ in the middle junction of the scaffold, and tendon on the other end of the scaffold. The scaffold containing regional mechanical heterogeneity most similar to the native MTJ (condition 3) was found to enhance the expression of MTJ-related markers compared to those without the presence of zonal stiffness regions. Overall, the DLP-based 3D printing platform and biomaterial system developed in this study could serve as a useful tool for mimicking the complexity of the native MTJ, which possesses inherent geometric and mechanical heterogeneity.

Ultrashort echo time magnetic resonance elastography for quantification of the mechanical properties of short T2 tissues via optimal control-based radiofrequency pulses

The aim of the current study is to demonstrate the feasibility of radiofrequency (RF) pulses generated via an optimal control (OC) algorithm to perform magnetic resonance elastography (MRE) and quantify the mechanical properties of materials with very short transverse relaxation times (T2 < 5 ms) for the first time. OC theory applied to MRE provides RF pulses that bring isochromats from the equilibrium state to a fixed target state, which corresponds to the phase pattern of a conventional MRE acquisition. Such RF pulses applied with a constant gradient allow to simultaneously perform slice selection and motion encoding in the slice direction. Unlike conventional MRE, no additional motion-encoding gradients (MEGs) are needed, enabling shorter echo times. OC pulses were implemented both in turbo spin echo (OC rapid acquisition with refocused echoes [RARE]) and ultrashort echo time (OC UTE) sequences to compare their motion-encoding efficiency with the conventional MEG encoding (classical MEG MRE). MRE experiments were carried out on agar phantoms with very short T2 values and on an ex vivo bovine tendon. Magnitude images, wave field images, phase-to-noise ratio (PNR), and shear storage modulus maps were compared between OC RARE, OC UTE, and classical MEG MRE in samples with different T2 values. Shear storage modulus values of the agar phantoms were in agreement with values found in the literature, and that of the bovine tendon was corroborated with rheometry measurements. Only the OC sequences could encode motion in very short T2 samples, and only OC UTE sequences yielded magnitude images enabling proper visualization of short T2 samples and tissues. The OC UTE sequence produced the best PNRs, demonstrating its ability to perform anatomical and mechanical characterization. Its success warrants in vivo confirmation in further studies.

Leveraging in vivo animal models of tendon loading to inform tissue engineering approaches

Tendon injuries disrupt successful transmission of force between muscle and bone, resulting in reduced mobility, increased pain, and significantly reduced quality of life for affected patients. There are currently no targeted treatments to improve tendon healing beyond conservative methods such as rest and physical therapy. Tissue engineering approaches hold great promise for designing instructive biomaterials that could improve tendon healing or for generating replacement graft tissue. More recently, engineered microphysiological systems to model tendon injuries have been used to identify therapeutic targets. Despite these advances, current tissue engineering efforts that aim to regenerate, replace, or model injured tendons have largely failed due in large part to a lack of understanding of how the mechanical environment of the tendon influences tissue homeostasis and how altered mechanical loading can promote or prevent disease progression. This review article draws inspiration from what is known about tendon loading from in vivo animal models and identifies key metrics that can be used to benchmark success in tissue engineering applications. Finally, we highlight important challenges and opportunities for the field of tendon tissue engineering that should be taken into consideration in designing engineered platforms to understand or improve tendon healing.

A comprehensive guide to western blotting for tendon research

Tendons are classified as dense fibrous connective tissue. This fibrous composition poses challenges in protein extraction, particularly hindering the application of Western blotting techniques. Because of these challenges, it becomes necessary to implement additional steps and specific solutions to attain success in this methodology with the tissue in question. The objective of this article is to provide a detailed protocol, elucidating each step, and making it easily replicable for researchers. The study focused on the Achilles tendons of Sprague-Dawley rats, emphasizing the need for a tailored approach in working with this tissue. By addressing the nuances of protein extraction from the dense and fibrous tendons, our protocol aims to facilitate the reproducibility of Western blotting experiments, contributing to a better understanding of this tissue.

Nanocrystal residual strains and density layers enhance failure resistance in the cleithrum bone of evolutionary advanced pike fish

Failure-resistant designs are particularly crucial for bones subjected to rapid loading, as is the case for the ambush-hunting northern pike (Esox lucius). These fish have slim and low-density osteocyte-lacking bones. As part of the swallowing mechanism, the cleithrum bone opens and closes the jaw. The cleithrum needs sufficient strength and damage tolerance, to withstand years of repetitive rapid gape-and-suck cycles of feeding. The thin wing-shaped bone comprises anisotropic layers of mineralized collagen fibers that exhibit periodic variations in mineral density on the mm and micrometer length scales. Wavy collagen fibrils interconnect these layers yielding a highly anisotropic structure. Hydrated cleithra exhibit Young's moduli spanning 3-9 GPa where the yield stress of ∼40 MPa increases markedly to exceed ∼180 MPa upon drying. This 5x observation of increased strength corresponds to a change to brittle fracture patterns. It matches the emergence of compressive residual strains of ∼0.15% within the mineral crystals due to forces from shrinking collagen layers. Compressive stresses on the nanoscale, combined with the layered anisotropic microstructure on the mm length scale, jointly confer structural stability in the slender and lightweight bones. By employing a range of X-ray, electron and optical imaging and mechanical characterization techniques, we reveal the structure and properties that make the cleithra impressively damage resistant composites. STATEMENT OF SIGNIFICANCE: By combining structural and mechanical characterization techniques spanning the mm to the sub-nanometer length scales, this work provides insights into the structural organization and properties of a resilient bone found in pike fish. Our observations show how the anosteocytic bone within the pectoral gridle of these fish, lacking any biological (remodeling) repair mechanisms, is adapted to sustain natural repeated loading cycles of abrupt jaw-gaping and swallowing. We find residual strains within the mineral apatite nanocrystals that contribute to forming a remarkably resilient composite material. Such information gleaned from bony structures that are different from the usual bones of mammals showcases how nature incorporates smart features that induce damage tolerance in bone material, an adaptation acquired through natural evolutionary processes.

Rotator Cuff Repair and Overlay Augmentation by Direct Interlocking of a Nonwoven Polyethylene Terephthalate Patch Into the Tendon: Evaluation in an Ovine Model

BACKGROUND

Arthroscopic repair of large rotator cuff tendon tears is associated with high rates of retear. Construct failure often occurs at the suture-tendon interface. Patch augmentation can improve mechanical strength and healing at this interface.

PURPOSE

To introduce a novel technique for suture-free attachment of an overlaid patch and evaluate its biomechanical strength and biological performance.

STUDY DESIGN

Descriptive and controlled laboratory studies.

METHODS

An established ovine model of partial infraspinatus tendon resection and immediate repair was used. After a nonwoven polyethylene terephthalate patch was overlaid to the resected tendon, a barbed microblade was used to draw fibers of the patch directly into the underlying tissue. In vivo histological assessment of healing was performed at 6 and 13 weeks after implantation. Ex vivo models were used to characterize primary repair strength of the suture-free patch fixation to tendon. Additional ex vivo testing assessed the potential of the technique for patch overlay augmentation of suture-based repair.

RESULTS

The in vivo study revealed no macroscopic evidence of adverse tissue reactions to the interlocked patch fibers. Histological testing indicated a normal host healing response with minimal fibrosis. Uniform and aligned tissue ingrowth to the core of the patch was observed from both the tendon and the bone interfaces to the patch. There was no evident retraction of the infraspinatus muscle, lengthening of the tendon, or tendon gap formation over 13 weeks. Ex vivo testing revealed that direct patch interlocking yielded tendon purchase equivalent to a Mason-Allen suture (150 ± 58 vs 154 ± 49 N, respectively; P = .25). In an overlay configuration, fiber interlocked patch augmentation increased Mason-Allen suture retention strength by 88% (from 221 ± 43 N to 417 ± 86 N; P < .01) with no detectable difference in repair stiffness.

CONCLUSION

Testing in an ovine model of rotator cuff tendon repair suggested that surgical interlocking of a nonwoven medical textile can provide effective biomechanical performance, support functional tissue ingrowth, and help avoid musculotendinous retraction after surgical tendon repair.

CLINICAL RELEVANCE

The novel technique may facilitate patch augmentation of rotator cuff repairs.

Mechanical properties of animal ligaments: a review and comparative study for the identification of the most suitable human ligament surrogates

The interest in the properties of animal soft tissues is often related to the desire to find an animal model to replace human counterparts due to the unsteady availability of human tissues for experimental purposes. Once the most appropriate animal model is identified, it is possible to carry out ex-vivo and in-vivo studies for the repair of ligamentous tissues and performance testing of replacement and support healing devices. This work aims to present a systematic review of the mechanical properties of ligaments reported in the scientific literature by considering different anatomical regions in humans and several animal species. This study was conducted according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) method. Moreover, considering the lack of a standard protocol for preconditioning of tissues, this aspect is also addressed. Ninety-six studies were selected for the systematic review and analysed. The mechanical properties of different animal species are reported and summarised in tables. Only results from studies reporting the strain rate parameter were considered for comparison with human ligaments, as they were deemed more reliable. Elastic modulus, ultimate tensile stress, and ultimate strain properties are graphically reported identifying the range of values for each animal species and to facilitate comparison between values reported in the scientific literature in animal and human ligaments. Useful similarities between the mechanical properties of swine, cow, and rat and human ligaments have been found.

A review on the use of porcine in tendon research

PURPOSE OF REVIEW

Large animals have been increasingly employed in tendon research; the objective of this review was to summarize the employment of porcine in tendon research.

RECENT FINDINGS

Literature before 2022-03-31 was searched using the following strategy: (pig[MeSH Terms]) AND (tendon[MeSH Terms]); (pig[MeSH Terms]) AND (tendon[title]); (tendon[MeSH Terms]) AND (porcine[title]); (tendon[title]) AND (porcine[title]); (tendon[MeSH Terms]) AND (pig[title]); (tendon[title]) AND (pig[title]); (tendon[MeSH Terms]) AND (swine[title]); (tendon[title]) AND (swine[title]). 296 studies were included in this review. There were wide application areas of porcine tendon, including tissue engineering tendons, training of surgical skills. Porcine tendon was used both in in vitro studies, such as anatomy, biomechanics, cytology, and material science as well as in in vivo studies. The research techniques of porcine tendon are relatively common.

SUMMARY

In conclusion, pigs have been widely used as a good animal model of tendon research. However, the limitations of porcine tendon research (the lack of anatomical research and in vivo studies) should be given more attention in future studies.

Travelling through the Natural Hierarchies of Type I Collagen with X-rays: From Tendons of Cattle, Horses, Sheep and Pigs

Type I collagen physiological scaffold for tissue regeneration is considered one of the widely used biomaterials for tissue engineering and medical applications. It is hierarchically organized: five laterally staggered molecules are packed within fibrils, arranged into fascicles and bundles. The structural organization is correlated to the direction and intensity of the forces which can be loaded onto the tissue. For a tissue-specific regeneration, the required macro- and microstructure of a suitable biomaterial has been largely investigated. Conversely, the function of multiscale structural integrity has been much less explored but is crucial for scaffold design and application. In this work, collagen was extracted from different animal sources with protocols that alter its structure. Collagen of tendon shreds excised from cattle, horse, sheep and pig was structurally investigated by wide- and small-angle X-ray scattering techniques, at both molecular and supramolecular scales, and thermo-mechanically with thermal and load-bearing tests. Tendons were selected because of their resistance to chemical degradation and mechanical stresses. The multiscale structural integrity of tendons' collagen was studied in relation to the animal source, anatomic location and source for collagen extraction.

Short-term vancomycin and buffer soaking does not change rabbit achilles tendon tensile material properties

BACKGROUND

Allograft tendons are commonly used during orthopedic surgery to reconstruct tissue that is severely damaged. Soaking the tendon in an antibiotic solution, specifically vancomycin, has been shown to lower the risk of post-operative infections. While some material properties of tendon and ligament after antibiotic soaking have previously been characterized, extensive sub-failure allograft tendon material properties after soaking in antibiotic solutions have not.

METHODS

Forty tendons were dissected from rabbits and soaked in either a phosphate buffered saline (PBS) only solution or vancomycin and PBS solution for five or 30 min. Immediately after soaking, quasi-static tensile experiments were performed in a materials testing system.

FINDINGS

Tissue nominal stress, Lagrange strain, toe-region properties and elastic modulus were characterized. For all forty tendons, the average elastic modulus was found to be 455 ± 37 MPa, the average transition strain (from toe-region to linear elastic region) was 0.0487 ± 0.0035, and the average transition stress was 9.71 ± 0.79 MPa. No statistically significant differences in any of these material properties were found across soaking medium or soaking time.

INTERPRETATION

From these results, we conclude that soaking an allograft tendon in antibiotic solution for up to 30 min prior to implantation does not change the tensile material properties of tendons, supporting current clinical practice.

Development of high resilience spiral wound suture-embedded gelatin/PCL/heparin nanofiber membrane scaffolds for tendon tissue engineering

This study develops a spiral wound scaffold based on gelatin/PCL/heparin (GPH) nanofiber membranes for tendon tissue engineering. By embedding sutures in dual layers of aligned GPH nanofiber membranes, prepared from mixed electrospinning of gelatin and PCL/heparin solutions, we fabricate a high resilience scaffold intended for the high loading environment experienced by tendons. The basic fibroblast growth factor (bFGF) was anchored to GPH scaffold through bioaffinity between heparin and bFGF, aim to provide biological cues for maintenance of tenogenic phenotype. In addition, the aligned nanofiber morphology is expected to provide physical cues toward seeded tenocytes. With sustained release of bFGF, GPH-bFGF can enhance proliferation, up-regulate tenogenic gene expression, and increase synthesis of tendon-specific proteins by tenocytes in vitro. Furthermore, by properly maintaining tendon phenotypes, GPH-bFGF/tenocytes constructs showed improved mechanical properties over GPH-bFGF. From in vivo study using GPH-bFGF/tenocytes constructs to repair rabbit Achilles tendon defects, neotendon tissue formation was confirmed from histological staining and biomechanical analysis. These findings collectively demonstrate that the newly designed GPH-bFGF scaffold could provide a niche for inducing tendon tissue regeneration by effectively restoring the tendon tissue structure and function.

Microfluidic Formulation of Topological Hydrogels for Microtissue Engineering

Microfluidics has recently emerged as a powerful tool in generation of submillimeter-sized cell aggregates capable of performing tissue-specific functions, so-called microtissues, for applications in drug testing, regenerative medicine, and cell therapies. In this work, we review the most recent advances in the field, with particular focus on the formulation of cell-encapsulating microgels of small "dimensionalities": "0D" (particles), "1D" (fibers), "2D" (sheets), etc., and with nontrivial internal topologies, typically consisting of multiple compartments loaded with different types of cells and/or biopolymers. Such structures, which we refer to as topological hydrogels or topological microgels (examples including core-shell or Janus microbeads and microfibers, hollow or porous microstructures, or granular hydrogels) can be precisely tailored with high reproducibility and throughput by using microfluidics and used to provide controlled "initial conditions" for cell proliferation and maturation into functional tissue-like microstructures. Microfluidic methods of formulation of topological biomaterials have enabled significant progress in engineering of miniature tissues and organs, such as pancreas, liver, muscle, bone, heart, neural tissue, or vasculature, as well as in fabrication of tailored microenvironments for stem-cell expansion and differentiation, or in cancer modeling, including generation of vascularized tumors for personalized drug testing. We review the available microfluidic fabrication methods by exploiting various cross-linking mechanisms and various routes toward compartmentalization and critically discuss the available tissue-specific applications. Finally, we list the remaining challenges such as simplification of the microfluidic workflow for its widespread use in biomedical research, bench-to-bedside transition including production upscaling, further in vivo validation, generation of more precise organ-like models, as well as incorporation of induced pluripotent stem cells as a step toward clinical applications.

Dynamic Load Model Systems of Tendon Inflammation and Mechanobiology

Dynamic loading is a shared feature of tendon tissue homeostasis and pathology. Tendon cells have the inherent ability to sense mechanical loads that initiate molecular-level mechanotransduction pathways. While mature tendons require physiological mechanical loading in order to maintain and fine tune their extracellular matrix architecture, pathological loading initiates an inflammatory-mediated tissue repair pathway that may ultimately result in extracellular matrix dysregulation and tendon degeneration. The exact loading and inflammatory mechanisms involved in tendon healing and pathology is unclear although a precise understanding is imperative to improving therapeutic outcomes of tendon pathologies. Thus, various model systems have been designed to help elucidate the underlying mechanisms of tendon mechanobiology via mimicry of the in vivo tendon architecture and biomechanics. Recent development of model systems has focused on identifying mechanoresponses to various mechanical loading platforms. Less effort has been placed on identifying inflammatory pathways involved in tendon pathology etiology, though inflammation has been implicated in the onset of such chronic injuries. The focus of this work is to highlight the latest discoveries in tendon mechanobiology platforms and specifically identify the gaps for future work. An interdisciplinary approach is necessary to reveal the complex molecular interplay that leads to tendon pathologies and will ultimately identify potential regenerative therapeutic targets.

Design and Mechanical Characterization Using Digital Image Correlation of Soft Tissue-Mimicking Polymers

Present and future anatomical models for biomedical applications will need bio-mimicking three-dimensional (3D)-printed tissues. These would enable, for example, the evaluation of the quality-performance of novel devices at an intermediate step between ex-vivo and in-vivo trials. Nowadays, PolyJet technology produces anatomical models with varying levels of realism and fidelity to replicate organic tissues. These include anatomical presets set with combinations of multiple materials, transitions, and colors that vary in hardness, flexibility, and density. This study aims to mechanically characterize multi-material specimens designed and fabricated to mimic various bio-inspired hierarchical structures targeted to mimic tendons and ligaments. A Stratasys® J750™ 3D Printer was used, combining the Agilus30™ material at different hardness levels in the bio-mimicking configurations. Then, the mechanical properties of these different options were tested to evaluate their behavior under uni-axial tensile tests. Digital Image Correlation (DIC) was used to accurately quantify the specimens' large strains in a non-contact fashion. A difference in the mechanical properties according to pattern type, proposed hardness combinations, and matrix-to-fiber ratio were evidenced. The specimens V, J1, A1, and C were selected as the best for every type of pattern. Specimens V were chosen as the leading combination since they exhibited the best balance of mechanical properties with the higher values of Modulus of elasticity (2.21 ± 0.17 MPa), maximum strain (1.86 ± 0.05 mm/mm), and tensile strength at break (2.11 ± 0.13 MPa). The approach demonstrates the versatility of PolyJet technology that enables core materials to be tailored based on specific needs. These findings will allow the development of more accurate and realistic computational and 3D printed soft tissue anatomical solutions mimicking something much closer to real tissues.