A programmable high-voltage compliance neural stimulator for deep brain stimulation in vivo

A Fully Integrated, Power-Efficient, 0.07-2.08 mA, High-Voltage Neural Stimulator in a Standard CMOS Process

This paper presents a fully integrated high-voltage (HV) neural stimulator with on-chip HV generation. It consists of a neural stimulator front-end that delivers stimulation currents up to 2.08 mA with 5 bits resolution and a switched-capacitor DC-DC converter that generates a programmable voltage supply from 4.2 V to 13.2 V with 4 bits resolution. The solution was designed and fabricated in a standard 180 nm 1.8 V/3.3 V CMOS process and occupied an active area of 2.34 mm2. Circuit-level and block-level techniques, such as a proposed high-compliance voltage cell, have been used for implementing HV circuits in a low-voltage CMOS process. Experimental validation with an electrical model of the electrode−tissue interface showed that (1) the neural stimulator can handle voltage supplies up to 4 times higher than the technology’s nominal supply, (2) residual charge—without passive discharging phase—was below 0.12% for the whole range of stimulation currents, (3) a stimulation current of 2 mA can be delivered with a voltage drop of 0.9 V, and (4) an overall power efficiency of 48% was obtained at maximum stimulation current.

Modular Current Stimulation System for Pre-clinical Studies

Electric stimulators with precise and reliable outputs are an indispensable part of electrophysiological research. From single cells to deep brain or neuromuscular tissue, there are diverse targets for electrical stimulation. Even though commercial systems are available, we state the need for a low-cost, high precision, functional, and modular (hardware, firmware, and software) current stimulation system with the capacity to generate stable and complex waveforms for pre-clinical research. The system presented in this study is a USB controlled 4-channel modular current stimulator that can be expanded and generate biphasic arbitrary waveforms with 16-bit resolution, high temporal precision (μs), and passive charge balancing: the NES STiM (Neuro Electronic Systems Stimulator). We present a detailed description of the system’s structural design, the controlling software, reliability test, and the pre-clinical studies [deep brain stimulation (DBS) in hemi-PD rat model] in which it was utilized. The NES STiM has been tested with MacOS and Windows operating systems. Interfaces to MATLAB source codes are provided. The system is inexpensive, relatively easy to build and can be assembled quickly. We hope that the NES STiM will be used in a wide variety of neurological applications such as Functional Electrical Stimulation (FES), DBS and closed loop neurophysiological research.

Stimulation and Artifact-Suppression Techniques for In Vitro High-Density Microelectrode Array Systems

We present novel voltage stimulation buffers with controlled output current, along with recording circuits featuring adjustable high-pass cut-off filtering to perform efficient stimulation while actively suppressing stimulation artifacts in high-density microelectrode arrays. Owing to the dense packing and close proximity of the electrodes in such systems, a stimulation through one electrode can cause large electrical artifacts on neighboring electrodes that easily saturate the corresponding recording amplifiers. To suppress such artifacts, the high-pass corner frequencies of all available 2048 recording channels can be raised from several Hz to several kHz by applying a "soft-reset" or pole-shifting technique. With the implemented artifact suppression technique, the saturation time of the recording circuits, connected to electrodes in immediate vicinity to the stimulation site, could be reduced to less than 150 μs. For the stimulation buffer, we developed a circuit, which can operate in two modes: either control of only the stimulation voltage or control of current and voltage during stimulation. The voltage-only controlled mode employs a local common-mode feedback operational transconductance amplifier with a near rail-to-rail input/output range, suitable for driving high-capacitive loads. The current/voltage controlled mode is based on a positive current conveyor generating adjustable output currents, whereas its upper and lower output voltages are limited by two feedback loops. The current/voltage controlled circuit can generate stimulation pulses up to 30 μA with less than ±0.1% linearity error in the low-current mode and up to 300 μA with less than ±0.2% linearity error in the high-current mode.

Building wireless implantable neural interfaces within weeks for neuroscientists

The variety of "`ready-to-use'" implantable recording and stimulation systems commercially available for neuroscience is very limited and fabrication of custom made implants is commonly considered expensive and time consuming. We present a circuit design that allows cost efficient and fast translation of available components into fully wireless implants. As demonstration fully wireless implantable bidirectional neural interfaces are presented which are made of commercial off-the-shelf components (COTS) only. It is demonstrated that they are competitive to currently available state-of-the-art systems regarding size and performance.

Design of a novel stimulation system with time-varying paradigms for investigating new modes of high frequency stimulation in brain

Background

Deep brain stimulation (DBS) has shown wide clinical applications for treating various disorders of central nervous system. High frequency stimulation (HFS) of pulses with a constant intensity and a constant frequency is typically used in DBS. However, new stimulation paradigms with time-varying parameters provide a prospective direction for DBS developments. To meet the research demands for time-varying stimulations, we designed a new stimulation system with a technique of LabVIEW-based virtual instrument.

Methods

The system included a LabVIEW program, a NI data acquisition card, and an analog stimulus isolator. The output waveforms of the system were measured to verify the time-varying parameters. Preliminary animal experiments were run by delivering the HFS sequences with time-varying parameters to the hippocampal CA1 region of anesthetized rats.

Results

Verification results showed that the stimulation system was able to generate pulse sequences with ramped intensity and hyperbolic frequency accurately. Application of the time-varying HFS sequences to the axons of pyramidal cells in the hippocampal CA1 region resulted in neuronal responses different from those induced by HFS with constant parameters. The results indicated important modulations of time-varying stimulations to the neuronal activity that could prevent the stimulation from inducing over-synchronized firing of population neurons.

Conclusions

The stimulation system provides a useful technique for investigating diverse stimulation paradigms for the development of new DBS treatments.