Study on the copper(II)-doped MIL-101(Cr) and its performance in VOCs adsorption

Performance on adsorption of toluene by ionic liquid-modified AC in high-humidity exhaust gas

Volatile organic compounds (VOCs) frequently pose a threat to the biosphere, impacting ecosystems, flora, fauna, and the surrounding environment. Industrial emissions of VOCs often include the presence of water vapor, which, in turn, diminishes the adsorption capacity and efficacy of adsorbents. This occurs due to the competitive adsorption of water vapor, which competes with target pollutants for adsorption sites on the adsorbent material. In this study, hydrophobic activated carbons (BMIMPF6-AC (L), BMIMPF6-AC (g), and BMIMPF6-AC-H) were successfully prepared using 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF6) to adsorb toluene under humidity environment. The adsorption performance and mechanism of the resulting ionic liquid-modified activated carbon for toluene in a high-humidity environment were evaluated to explore the potential application of ionic liquids as hydrophobic modifiers. The results indicated that BMIMPF6-AC-H exhibited superior hydrophobicity. The toluene adsorption capacity of BMIMPF6-AC-H was 1.53 times higher than that of original activated carbon, while the adsorption capacity for water vapor was only 37.30% of it at 27 °C and 77% RH. The Y-N model well-fitted the dynamic adsorption experiments. To elucidate the microscopic mechanism of hydrophobic modification, the Independent Gradient Model (IGM) method was employed to characterize the intermolecular interactions between BMIMPF6 and toluene. Overall, this study introduces a new modifier for hydrophobic modification of activated carbon, which could enhance the efficiency of activated carbon in treating industrial VOCs.

Enhanced benzene vapor adsorption through microwave-assisted fabrication of activated carbon from peanut shells using ZnCl2 as an activating agent

Herein, microwave-assisted activated carbon (MW-AC) was fabricated from peanut shells using a ZnCl2 activator and utilized for the first time to eliminate benzene vapor as a volatile organic compound (VOC). During the MW-AC production process, which involved two steps-microwave treatment and muffle furnace heating-we investigated the effects of various factors and achieved the highest iodine number of 1250 mg/g. This was achieved under optimal operating conditions, which included a 100% impregnation ratio, CO2 as the gas in the microwave environment, a microwave power set at 500 W, a microwave duration of 10 min, an activation temperature of 500 °C and an activation time of 45 min. The structural and morphological properties of the optimized MW-AC were assessed through SEM, FTIR, and BET analysis. The dynamic adsorption process of benzene on the optimized MW-AC adsorbent, which has a significant BET surface area of 1204.90 m2/g, was designed using the Box-Behnken approach within the response surface methodology. Under optimal experimental conditions, including a contact duration of 80 min, an inlet concentration of 18 ppm, and a temperature of 26 °C, the maximum adsorption capacity reached was 568.34 mg/g. The experimental data are better described by the pseudo-second-order kinetic model, while it is concluded that the equilibrium data are better described by the Langmuir isotherm model. MW-AC exhibited a reuse efficiency of 86.54% for benzene vapor after five consecutive recycling processes. The motivation of the study highlights the high adsorption capacity and superior reuse efficiency of MW-AC adsorbent with high BET surface area against benzene pollutant. According to our results, the developed MW-AC presents itself as a promising adsorbent candidate for the treatment of VOCs in various industrial applications.

Porous functional metal–organic frameworks (MOFs) constructed from different N-heterocyclic carboxylic ligands for gas adsorption/separation

This review mainly summarizes the recent progress of MOFs composed of N-heterocyclic carboxylate ligands in gas sorption/separation. This work may help to understand the relationship between the structures of MOFs and gas sorption/separation.

Experimental and Simulation Studies of the Adsorption of Methylbenzene by Fe(III)-Doped NU-1000 (Zr)

Metal-organic framework (MOF) materials, NU-1000(Zr) and Fe(III)-doped NU-1000(Zr), were prepared through the hydrothermal method and used to remove methylbenzene in this work. The pore structure, crystal structure, adsorption capacity, adsorption heat, and adsorption density of Fe(III)-doped NU-1000(Zr) were analyzed based on the experimental and Giant Canonical Monte Carlo (GCMC) simulation methods. The results show that Fe³⁺ has a uniform distribution and a stable structure after NU-1000(Zr) was modified with Fe³⁺. The adsorption-penetration experiments of NU-1000 doped with different concentrations of Fe³⁺ have shown that the adsorption capacity of methylbenzene on the material surface is up to 231 mg g^-1 at Fe/Zr = 0.1, which is due to the less doping of Fe elements and more defective sites in the structure. The GCMC simulation shows that NU-1000(Zr) and Fe(III)-NU-1000(Zr) adsorbed methylbenzene through π-π interaction, and the adsorption effect is good and close to the experimental result. The conclusions of this paper provide important support for the modification of MOF materials and the removal of methylbenzene.

Synthesis and Characterization of the Metal–Organic Framework CIM-80 for Organic Compounds Adsorption

Metal–organic frameworks (MOF) are a new type of porous materials that have great potential for adsorption of voltaic organic compounds (VOCs). These types of materials composed of metal ions and organic ligands are easy to synthesize, have high surface areas, their surface chemistry can be adjusted to the desired application, and they can also have good chemical and thermal stability. Therefore, this work focuses on the synthesis of a highly hydrophobic MOF material called CIM-80, a porous material that is made up of the Al³⁺ cation and the mesaconate linker. This MOF has a B.E.T. of approximately 800 m²/g and has potential applications for the adsorption of hydrophobic organic compounds. However, its synthesis is expensive and very dirty. Therefore, we have studied the synthesis conditions necessary to achieve high synthesis yields (85%) and materials with high crystallinity and accessible porosity. To achieve these results, we have used urea as a mild deprotonation reagent and modulator as an alternative to NaOH, which is traditionally used for the synthesis of this MOF. Once the synthesis of this material was controlled, its adsorption/desorption behavior of water and organic compounds such as toluene, cyclohexane and m-xylene was studied by means of vapor adsorption isotherms. The results show the hydrophobic character of the material and the greater affinity the material has toward aliphatic compounds than toward aromatic ones, with toluene being the most adsorbed compound, followed by cyclohexane and m-xylene.

Keggin-type SiW12 encapsulated in MIL-101(Cr) as efficient heterogeneous photocatalysts for nitrogen fixation reaction

The incorporation of polyoxometalates (POMs) in metal-organic frameworks (MOFs) with host-guest structure have proven to be effective strategy to rational design of heterogeneous catalysis. In this study, the Keggin-type POM@MIL-101(Cr) composite catalysts (PMo₁₂, PW₁₂ and SiW₁₂) are synthesized for nitrogen fixation reaction without sacrificial agents at room temperature in the first time. The SiW₁₂ molecules are encapsulated in smaller cavities of MIL-101(Cr) by solvothermal method and in larger cavities by impregnation method, respectively. Solvothermal synthesized catalyst has a performance of 75.56 μmol·h^-1·g^-1_cat and TOF value of 1.95 h^-1, which are about 10 and 88 times than that of Na₄SiW₁₂O₄₀. The excellent performance is ascribed to the synergistic effect of SiW₁₂ and MIL-101(Cr). The MIL-101(Cr) adsorbs a large amount of N₂ and generates sufficiently photogenerated electrons under sunlight irradiation, and electrons quickly transfer to the SiW₁₂ through hydrogen bonds. Moreover, the agglomeration effect of the homogeneous catalyst SiW₁₂ is weakened due to encapsulation with more exposed active sites. This work provides a feasible route to design and synthesize nanocomposite materials with exceptional performance for photocatalytic nitrogen fixation.

Recent Developments in the Application of Bio-Waste-Derived Adsorbents for the Removal of Methylene Blue from Wastewater: A Review

Over the last few years, various industries have released wastewater containing high concentrations of dyes straight into the ecological system, which has become a major environmental problem (i.e., soil, groundwater, surface water pollution, etc.). The rapid growth of textile industries has created an alarming situation in which further deterioration to the environment has been caused due to substances being left in treated wastewater, including dyes. The application of activated carbon has recently been demonstrated to be a highly efficient technology in terms of removing methylene blue (MB) from wastewater. Agricultural waste, as well as animal-based and wood products, are excellent sources of bio-waste for MB remediation since they are extremely efficient, have high sorption capacities, and are renewable sources. Despite the fact that commercial activated carbon is a favored adsorbent for dye elimination, its extensive application is restricted because of its comparatively high cost, which has prompted researchers to investigate alternative sources of adsorbents that are non-conventional and more economical. The goal of this review article was to critically evaluate the accessible information on the characteristics of bio-waste-derived adsorbents for MB’s removal, as well as related parameters influencing the performance of this process. The review also highlighted the processing methods developed in previous studies. Regeneration processes, economic challenges, and the valorization of post-sorption materials were also discussed. This review is beneficial in terms of understanding recent advances in the status of biowaste-derived adsorbents, highlighting the accelerating need for the development of low-cost adsorbents and functioning as a precursor for large-scale system optimization.

Key factors and primary modification methods of activated carbon and their application in adsorption of carbon-based gases: A review

To achieve carbon neutrality, it is necessary to control carbon-based gas emissions to the atmosphere. Among the various carbon-based gas removal technologies reported to date, adsorption is considered one of the most promising because of its economic efficiency, reusability, and low energy consumption. Activated carbon is widely used to treat different types of carbon-based gases owing to its large specific surface area, abundant functional groups, and strong adsorption capacity. This paper reviews the recent research progress into activated carbon as an adsorbent for carbon-based gases. The key factors (i.e., specific surface area, pore structure, and surface functional groups) affecting the adsorption of carbon-based gases by activated carbon were analyzed. The main methods employed to modify activated carbon (i.e., surface oxidation, surface reduction, loading materials, and plasma modification methods) to improve its adsorption capacity are also discussed herein, along with the targeted applications of such material in the adsorption of different types of carbon-based gases (such as aldehydes, ketones, aromatic hydrocarbons, halogenated hydrocarbons, and carbon-based greenhouse gases). Finally, the future development directions and challenges of activated carbon are discussed. Our work will be expected to benefit the development of activated carbon exhibiting selective adsorption properties, and reduce the production costs of adsorbents.

UiO-66 Selective Enrichment Integrated with Thermal Desorption GC-MS for Detection of Benzene Homologues in Ambient Air

In this study, UiO-66 was selected as sorbent media packed in the tube to selectively enrich trace levels of benzene homologues such as benzene, toluene, and xylene (BTX) in ambient air prior to thermal desorption (TD)-GC-MS determination. A series of experiments were conducted to obtain the optimal TD conditions. The results indicated that the optimal TD parameters were as follows: desorption temperature of 180°C, desorption flow rate of 50 mL min^-1, and desorption time of 30 min. Furthermore, the method based on UiO-66 enrichment integrated with TD-GC-MS for trace levels of BTX was successfully developed. It exhibited a good linearity (R ² > 0.99) in the range of 50-1000 ng, except for p, m-xylene in the range of 100-2000 ng, and achieved the recovery of 69.4-101.3%, and the relative standard deviation of 3.8-6.4%. The detection limits of BTX were 1.6-4.0 ng; according to 10 L of sampling volume, the method detection limits would be in the range of 0.16-0.40 µg m^-3. Additionally, the method was successfully applied to determine BTX in indoor air and showed good selectivity and sensitivity. In summary, the findings in this work revealed that UiO-66 was an attractive adsorbent for selective enrichment trace levels of BTX compounds in ambient air, which was favorable for the subsequent detection by TD-GC-MS.

Porous structured cotton-based ACF for the adsorption of benzen

Fibrous activated carbon has attracted emerging research interests due to its remarkable adsorption performance for volatile organic compounds (VOCs). Though this adsorption behavior for VOCs is closely related to the pore structure on the surface of activated carbon fiber (ACF), few researchers paid attentions to the influence of textural properties of this adsorption process. Especially, cotton-based activated carbon fiber (CACF) for adsorbing benzene pollutant is rarely reported. Herein, in order to develop a high-performance adsorbent for the removal of VOCs pollutants, this work studied the influence of textural properties of CACF on the adsorption of benzene. The results showed that the increase of carbonization temperature would lead to the reduction of mesopores but the increase of micropores for CACF; the embedment of phosphoric acid and its derivatives into the carbon layers contributed to the formation of pore structure for CACF; furthermore, specific surface area of CACF can also be enlarged by increasing the concentration of phosphoric acid. More importantly, it was found that the adsorption capacity of CACF for benzene was strongly dependent on the specific surface area and volume of micropores within CACF because micropores can provide more favorable binding sites. This adsorption process preferred to occur on the wall of micropores, then the accumulated benzene would slowly fill the pores. Interestingly, the decrease of pore size of micropores can unexpectedly improve the affinity of CACF to benzene on the contrary. This work provides a new strategy to develop porous structured ACF materials for the high-performance adsorption of VOCs.

Adsorption performance and kinetic study of hierarchical porous Fe-based MOFs for toluene removal

In light of the promising merits of large surface area, uniform pore size, and tunable functional groups, metal-organic frameworks (MOFs) have great potential to be utilized for adsorbing volatile organic compounds (VOCs). In this study, three Fe-based MOFs, MIL-100(Fe), MIL-101(Fe), and MIL-53(Fe), were synthesized systematically and used to adsorb a typical VOC, toluene. Static adsorption, dynamic breakthrough curves, and adsorption kinetics were conducted to assess the adsorption performance. Additionally, the surface functional groups, pore structure, and morphology were systematically characterized by means of XRD, SEM, XPS, FTIR and N₂ adsorption-desorption analyses to reveal the cause of the difference in adsorption of these Fe-based MOFs. The results revealed that the maximum equilibrium adsorption capacity of 663 mg/g was achieved by MIL-100(Fe) with the highest specific surface area and pore volume. The dynamic adsorption of toluene on MIL-100(Fe) was in accordance with the pseudo-first order kinetic model and the Langmuir isothermal model. The formed π-π stacking interaction between organic ligands and the benzene ring in the MIL-100(Fe) cluster is the primary adsorption mechanism based on XPS analysis. Moreover, MIL-100(Fe) was easily regenerated via microwave irradiation with a negligible adsorption capacity decrease after three cycles. This work highlights the feasibility of hierarchical porous Fe-based MOFs as toluene adsorbents and promotes the application of MOFs in the field of pollution control.

Novel Porous Carbon Material for the Detection of Traces of Volatile Organic Compounds in Indoor Air

A highly sensitive and selective silicon-based microanalytical prototype was used to identify a few ppb of volatile organic compounds (VOCs) in indoor air. Herein, a new nonactivated tannin-derived carbon synthesized by an environmentally friendly method, DM2C, a MIL-101(Cr) MOF, and a DaY zeolite were selected for the preconcentration of BTEX compounds (i.e., benzene, toluene, ethylbenzene, and xylenes). Integrating a small amount of these nanoporous solids inside a miniaturized preconcentration unit led to excellent preconcentration performance. By taking advantage of the high adsorption-desorption capacities of the DM2C adsorbent, concentrations as low as 23.5, 30.8, 16.7, 25, and 28.8 ppb of benzene, toluene, ethylbenzene, ortho- and para-xylene, respectively, were detected in a short analysis time (∼10 min) even in the presence of 60% relative humidity at 25 °C. The DM2C showed excellent stability over a period of 4 months and more than 500 tests, as well as repeatability, which makes it a very reliable adsorbent for the detection of trace VOCs in indoor air under realistic conditions in the presence of humidity.

Mitigation of indoor air pollution: A review of recent advances in adsorption materials and catalytic oxidation

Indoor air pollution with toxic volatile organic compounds (VOCs) and fine particulate matter (PM2.5) is a threat to human health, causing cancer, leukemia, fetal malformation, and abortion. Therefore, the development of technologies to mitigate indoor air pollution is important to avoid adverse effects. Adsorption and photocatalytic oxidation are the current approaches for the removal of VOCs and PM2.5 with high efficiency. In this review we focus on the recent development of indoor air pollution mitigation materials based on adsorption and photocatalytic decomposition. First, we review on the primary indoor air pollutants including formaldehyde, benzene compounds, PM2.5, flame retardants, and plasticizer: Next, the recent advances in the use of adsorption materials including traditional biochar and MOF (metal-organic frameworks) as the new emerging porous materials for VOCs absorption is reviewed. We review the mechanism for mitigation of VOCs using biochar (noncarbonized organic matter partition and adsorption) and MOF together with parameters that affect indoor air pollution removal efficiency based on current mitigation approaches including the mitigation of VOCs using photocatalytic oxidation. Finally, we bring forward perspectives and directions for the development of indoor air mitigation technologies.

Fabrication and characterization of 3,4-diaminobenzophenone-functionalized magnetic nanoadsorbent with enhanced VOC adsorption and desorption capacity

The present study, for the first time, utilized 3,4-diaminobenzophenone (DABP)-functionalized Fe₃O₄/AC@SiO₂ (Fe₃O₄/AC@SiO₂@DABP) magnetic nanoparticles (MNPs) synthesized as a nanoadsorbent for enhancing adsorption and desorption capacity of gaseous benzene and toluene as volatile organic compounds (VOCs). The Fe₃O₄/AC@SiO₂@DABP MNPs used in adsorption and desorption of benzene and toluene were synthesized by the co-precipitation and sol-gel methods. The synthesized MNPs were characterized by SEM, FTIR, TGA/DTA, and BET surface area analysis. Moreover, the optimization of the process parameters, namely contact time, initial VOC concentration, and temperature, was performed by applying response surface methodology (RSM). Adsorption results demonstrated that the Fe₃O₄/AC@SiO₂@DABP MNPs had excellent adsorption capacity. The maximum adsorption capacities for benzene and toluene were found as 530.99 and 666.00 mg/g, respectively, under optimum process parameters (contact time 55.47 min, initial benzene concentration 17.57 ppm, and temperature 29.09 °C; and contact time 57.54 min, initial toluene concentration 17.83 ppm, and temperature 27.93 °C for benzene and toluene, respectively). In addition to the distinctive adsorptive behavior, the Fe₃O₄/AC@SiO₂@DABP MNPs exhibited a high reproducibility adsorption and desorption capacity. After the fifth adsorption and desorption cycles, the Fe₃O₄/AC@SiO₂@DABP MNPs retained 94.4% and 95.4% of its initial adsorption capacity for benzene and toluene, respectively. Kinetic and isotherm findings suggested that the adsorption mechanisms of benzene and toluene on the Fe₃O₄/AC@SiO₂@DABP MNPs were physical processes. The results indicated that the successfully synthesized Fe₃O₄/AC@SiO₂@DABP MNPs can be applied as an attractive, highly effective, reusable, and cost-effective adsorbent for the adsorption of VOC pollutants.Graphical abstract.

Multiple Functions of Gas Separation and Vapor Adsorption in a New MOF with Open Tubular Channels

Separation or purification is one of the difficult problems in the petrochemical industry. To help solve the difficulty of separation or purification for C₂H₂/CO₂ and C₂H_n/CH₄ in the chemical industry, we synthesized a new metal-organic framework (MOF), [Ni(dpip)]·2.5DMF·H₂O (1), by a bipyridyl-substituted isophthalic acid ligand. The MOF includes two types of one-dimensional (1D) tubular channels with different sizes and porous environments. The unique tubular channels lead to not only remarkable gas sorption capacity of C₂H₄, C₂H₂, and CO₂, but also good selectivity for C₂H₂/CH₄, C₂H₂/CH₄, CO₂/CH₄, and C₂H₂/CO₂, as demonstrated by single-component sorption isotherm results, ideal adsorbed solution theory calculations, and dynamic breakthrough curves. Grand canonical Monte Carlo (GCMC) simulation reveals preferential adsorption sites in the MOF for CO₂, C₂H₂, and C₂H₄. The MOF also exhibits an obvious size-selective absorption effect on vapor molecules.

A Dy6-cluster-based fcu-MOF with efficient separation of C2H2/C2H4 and selective adsorption of benzene

A stable Dy-MOF was constructed based on hexanuclear clusters, and contains F-decorated pores and reveals separation performance for C₂H₂/CH₄, C₂H₄/CH₄ and C₂H₂/C₂H₄ and selective adsorption of benzene/cyclohexane and benzene/toluene.

Ultrasound irradiation effect on morphological and adsorptive properties of a nanoscale 3D Zn-coordination polymer and derived oxide

In this work, Zn-based coordination polymer [Zn₂(1,3-bdc)bzim₂]_n was successfully synthesized by the sonochemical method using a 13 mm probe-type ultrasound operating at 20 kHz and amplitudes of 30, 40 and 50% corresponding to an acoustic power of 5.5, 8.6, and 10.3 W, respectively. Additionally, a sample was prepared by the slow-diffusion method for comparison. The samples were characterized by FTIR, PXRD, SEM, and BET techniques. The influence of the time and sonication amplitude on the yield of the reaction, crystallite size, and morphology were also studied. It was found that the sonochemical method provided the desired product in 83.9% within 20 min of sonication using the highest level of sonication amplitude. Moreover, this approach resulted in regular, controlled morphology, smaller particles, and higher surface area of the Zn-sample and derived oxide, than the slow diffusion method. The samples prepared by different methodologies were tested for the adsorption of BTEX (benzene, toluene, ethylbenzene, and xylenes) components in six different systems, and the uptakes were quantified by ¹³C NMR spectroscopy. Both samples showed excellent adsorption of benzene, 119.8 mmol/g, and 88.1 mmol/g, for the coordination polymers prepared via the sonochemical and slow-diffusion methods, respectively, corresponding to 63.9%, and 46.9%. These results are in agreement with the non-polar surface of these samples.

Efficient C2Hn Hydrocarbons and VOC Adsorption and Separation in an MOF with Lewis Basic and Acidic Decorated Active Sites

To help address efficient separation of C₂H_n light hydrocarbons and C₂H₂/CO₂ in the chemical industry, the self-assembly via an azolate-carboxylate ligand and Co(II) ion gave rise to a new porous MOF material, [Co(btzip)(H₂btzip)]·2DMF·2H₂O (1) (H₂btzip = 4,6-bis(triazol-1-yl)isophthalic acid). In the MOF, the pores are modified by rich uncoordinated triazolyl Lewis basic N atoms and acidic -COOH groups, which strengthen interactions with C₂H_n hydrocarbons and CO₂ molecules, leading to high adsorption amounts for C₂H_2, C₂H₄, C₂H₆, and CO₂ and remarkable separation efficiency for C₂H_n-CH₄, CO₂-CH₄, and C₂H₂-CO₂ mixtures, as confirmed by breakthrough experiments on the realistic gas mixtures. The MOF also reveals outstanding selective adsorption ability for benzene/toluene, methanol/1-propanol, methanol/2-propanol, and 2-propanol/1-propanol isomers. Molecular simulations disclose the different adsorption sites in the MOF for various adsorbates.

The research trends of metal-organic frameworks in environmental science: a review based on bibliometric analysis

Metal-organic frameworks, an emerging class of porous material, have developed rapidly in recent years. In order to clarify the application of metal-organic frameworks in the field of environmental science, 1386 articles over the last 20 years were obtained from Scopus and analysed by the bibliometric method. And the collaboration between countries, institutions and authors and the co-occurrence of keywords were also conducted using VOSviewer. The results indicated that this area of research has entered a fast-developing stage. The number of articles published has grown from 7 articles in 1999 to 378 articles in 2018. The most productive country was China with 626 articles published. The most productive institution was the Chinese Academy of Sciences, and the most productive author was Jhung SH from Kyungpook National University of South Korea. Although metal-organic frameworks have been widely used in adsorption and catalytic degradation of pollutants from the environment, the removal mechanism of pollutants by MOFs, the stability improvement and the cost reduction of metal-organic frameworks are still the main challenges for their practical applications.

A critical review on VOCs adsorption by different porous materials: Species, mechanisms and modification methods

Volatile organic compounds (VOCs) have attracted world-wide attention regarding their serious hazards on ecological environment and human health. Industrial processes such as fossil fuel combustion, petrochemicals, painting, coatings, pesticides, plastics, contributed to the large proportion of anthropogenic VOCs emission. Destructive methods (catalysis oxidation and biofiltration) and recovery methods (absorption, adsorption, condensation and membrane separation) have been developed for VOCs removal. Adsorption is established as one of the most promising strategies for VOCs abatement thanks to its characteristics of cost-effectiveness, simplicity and low energy consumption. The prominent progress in VOCs adsorption by different kinds of porous materials (such as carbon-based materials, oxygen-contained materials, organic polymers and composites is carefully summarized in this work, concerning the mechanism of adsorbate-adsorbent interactions, modification methods for the mentioned porous materials, and enhancement of VOCs adsorption capacity. This overview is to provide a comprehensive understanding of VOCs adsorption mechanisms and up-to-date progress of modification technologies for different porous materials.

MOFs-carbon hybrid nanocomposites in environmental protection applications

The demand for green engineering environmentally friendly nanomaterials had made carbon nanotube a suitable material to keep metal-organic frameworks (MOFs) in the application of wastewater treatment and air pollution monitoring systems. This review summarizes many of the recent research accomplishments in the synthesis of MOFs and MOFs-carbon hybrid nanocomposites for various applications such as wastewater treatment and removal of hazardous gases (CO, SO₂, H₂S and NH₃) with emphasis on MOF/CNTs composites. This review focuses on the efficient removal of pollutants from the environment using adsorption techniques. Another important application of MOFs composite discussed in this review is sensor materials for environmental pollution.

Efficient removal of formaldehyde by polyethyleneimine modified activated carbon in a fixed bed

Polyethyleneimine modified activated carbon (PEI-AC) was prepared through a treatment of immersion, and used for the adsorption of formaldehyde. The adsorption capacity of formaldehyde by unmodified AC is 190.1 mg g^-1, and the adsorption capacity of formaldehyde can reach to 317.6 mg g^-1 after 10 g L^-1 of PEI modified, being about 1.67 times than unmodified activated carbon (AC: 191.2 mg g^-1). And the 10 g L^-1 of PEI modified AC (PAC-30) has the highest adsorption capacity of formaldehyde, reached to 650 mg g^-1, with an increasing magnitude of 240% in comparison with that without modified AC. This is mainly due to changes in the pore structure and surface functional groups after modification. However, as the PEI concentration increases, the adsorption performance is inhibited. Through kinetic studies, it was found that all adsorption curves follow the second-order kinetics, and the breakthrough curves follow the Boltzmann model, and the adsorption process can also be described by the intraparticle diffusion model.

Investigation of high-performance adsorption for benzene and toluene vapors by calix[4]arene based organosilica (CBOS)

Calix[4]arene based organosilica (CBOS) was successfully prepared, characterized, and used for the adsorption of benzene and toluene vapors for the first time. The benzene and toluene vapor uptake of CBOS was determined to be 606 and 672 mg g⁻¹, respectively.

Novel Hierarchical Fe(III)-Doped Cu-MOFs With Enhanced Adsorption of Benzene Vapor

New hierarchical Fe(III)-doped Cu-MOFs (Fe-HK) were developed via introduction of Fe³⁺ ions during HKUST-1 synthesis. The obtained products were characterized by N₂ adsorption, X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, FTIR spectroscopy, and thermal analysis. The adsorption isotherms and kinetics of benzene vapor were measured and consecutive adsorption–desorption cycles were performed. It was found that the hierarchical-pore Fe-HK-2 exhibited optimal textural properties with high BET surface area of 1,707 m²/g and total pore volume of 0.93 cm³/g, which were higher than those of the unmodified HKUST-1. Significantly, the hierarchical-pore Fe-HK-2 possessed outstanding benzene adsorption capacity, which was 1.5 times greater than the value on HKUST-1. Benzene diffusivity of Fe-HK-2 was 1.7 times faster than that of parent HKUST-1. Furthermore, the benzene adsorption on Fe-HK-2 was highly reversible. The hierarchical-pore Fe-HK-2 with high porosity, outstanding adsorption capacity, enhanced diffusion rate, and excellent reversibility might be an attractive candidate for VOCs adsorption. This may offer a simple and effective strategy to synthesize hierarchical-pore MOFs by doping with other metal ions.

Competitive Adsorption of Methanol-Acetone on Surface Functionalization (-COOH, -OH, -NH2, and -SO3H): Grand Canonical Monte Carlo and Density Functional Theory Simulations

The capture and separation properties of surface-functionalized activated carbons (AC-Rs, R= -COOH, -OH, -NH₂, and -SO₃H) for the methanol-acetone mixture were investigated for the first time by grand canonical Monte Carlo simulation (GCMC) and density functional theory (DFT). The effects of surface functional groups and structural characteristics of AC-Rs on the adsorption and separation behaviors of methanol and acetone were clarified. The surface functional group with strong electron-donating or electron-accepting capacity (i.e., -NH₂, -OH, and -SO₃H) was a crucial factor for the methanol-acetone capture and separation performance at the lower pressure range, and the accessible surface area was found to be another determinative factor. AC-NH₂ with the relatively large accessible surface area (4497 m²/g) exhibited an efficient capture performance for the single component (15.7 mol/kg for methanol and 6.7 mol/kg for acetone) and the highest methanol/acetone selectivity (∼23) at 0.02 kPa. At high pressures, the surface functionalization and available pore volume of AC-Rs played pivotal roles in the adsorptive separation process. This study provided mechanistic insights on how the surface functional groups affected the capture and separation properties of ACs, which would further provide a rational alternative strategy in the preparation and synthesis of ACs for the effective gas mixture separation.

Alkali promoted the adsorption of toluene by adjusting the surface properties of lignin-derived carbon fibers

The lignin-based carbon fibers were prepared by electrospinning followed by stabilization, carbonization, and activation (i.e., steam activation, one-step KOH activation, and metal activation). The effect of carbonization temperature on prepared carbon fibers (CFs) was investigated. As a result, 800 °C is the most suitable carbonization temperature because the prepared carbon fibers possess greater specific surface area and pore volume. With the help of various characterization methods, the structural characteristics of the activated carbon fibers (ACFs) prepared by the three activation methods and the adsorption performance of toluene were compared. It was observed that the activated carbon fibers prepared by KOH one-step activation method (ACFK) exhibited higher specific surface area (1147.16 m²/g) and greater toluene adsorption (463 mg/g). Particularly, abundant microporous structures and surface functional groups play a vital role in the adsorption process. Further, the adsorption performance of toluene onto ACFK was further investigated in a gas-phase dynamic adsorption system and the results showed that ACFK has great potential application in adsorption of volatile organic compounds.

Acetone adsorption capacity of sulfur-doped microporous activated carbons prepared from polythiophene

Sulfur-doped activated carbons (SACs) with high sulfur content and large specific surface area were synthesized from polythiophene for acetone removal. The sulfur content of carbons (3.10-8.43 at.%) could be tunable by adjusting the activation temperature. The BET surface area and pore volume of the obtained samples were 916-2020 m² g^-1 and 0.678-1.100 cm³ g^-1, with a significant proportion of microporosity (up to 84% and 72% for BET surface area and pore volume, respectively). The resulting SACs show a superior acetone adsorption capacity (i.e., 716.4 mg g^-1 at 15 °C and 705 mg g^-1 at 25 °C for SAC700). In terms of the adsorption behavior of acetone on the activated carbons, compared to the Langmuir model, the Langmuir-Freundlich model showed better agreement with the adsorption amount. The results reveal that the surface area and micropore volume are the key factors for acetone adsorption, while the sulfur-doped functional groups, especially oxidized sulfur functional groups, can enhance the acetone adsorption capacity at a certain low pressure. Temperature programmed desorption (TPD) experiments were performed to get desorption activation energy of acetone on SAC samples, and the results ranged from 23.54 to 38.71 kJ mol^-1. The results of the molecular simulation show that the introduction of sulfur element can increase the binding energy between acetone molecule and carbon surface, and the tri-oxidized sulfur (sulfonic acid) functional group has the highest binding energy of - 0.4765 eV. Graphical abstract.