Relationship between the elastic modulus of the cage material and the biomechanical properties of transforaminal lumbar interbody fusion: A logarithmic regression analysis based on parametric finite element simulations

Biomechanical Analysis of a Newly Proposed Surgical Combination (MIS Screw-Rod System for Indirect Decompression+ Interspinous Fusion System for long Term Spinal Stability) in Treatment of Lumbar Degenerative Diseases

OBJECTIVE

The aim of this study is to analyze the biomechanical stability of a newly proposed surgical combination (minimally invasive surgery of screw-rod system for indirect decompression + interspinous fusion system for long term spinal stability) in treatment of lumbar degenerative diseases.

METHODS

The three-dimensional (3D) computed tomography (CT) image data of an adult healthy male volunteer were selected. An intact model of L4/5 was further established and validated by using Mimic and 3-matic, 3D slicer, abaqus, Python. Four surgical models were constructed. The biomechanical stability among these surgical modes was compared and analyzed using finite element analysis.

RESULTS

The maximum von mises on fixation system in surgical models 2 and 3 exhibited comparable values. This finding suggested that the increase in interspinous fusion did not result in a significant elevation in maximum von mises on fixation system. Compared with the third surgical model, the fourth model, which received less average von mises experienced by the screw in contact with both cancellous and cortical bone. The findings indicated that the inclusion of facet joint fusion in surgical procedures might not be necessary to increase the average von Mises stress experienced by the screw in contact with both cancellous and cortical bone.

CONCLUSIONS

The biomechanical stability of the newly proposed surgical combination (MIS screw-rod for indirect decompression + interspinous fusion for long term spinal stability technique) was not lower than that of the other surgical combination groups, and it might not be necessary to perform facet joint fusion during the surgery.

Determining a relative total lumbar range of motion to alleviate adjacent segment degeneration after transforaminal lumbar interbody fusion: a finite element analysis

BACKGROUND

A reduction in total lumbar range of motion (ROM) after lumbar fusion may offset the increase in intradiscal pressure (IDP) and facet joint force (FJF) caused by the abnormally increased ROM at adjacent segments. This study aimed to determine a relative total lumbar ROM rather than an ideal adjacent segment ROM to guide postoperative waist activities and further delay adjacent segment degeneration (ASD).

METHODS

An intact L1-S1 finite element model was constructed and validated. Based on this, a surgical model was created to allow the simulation of L4/5 transforaminal lumbar interbody fusion (TLIF). Under the maximum total L1-S1 ROM, the ROM, IDP, and FJF of each adjacent segment between the intact and TLIF models were compared to explore the biomechanical influence of lumbar fusion on adjacent segments. Subsequently, the functional relationship between total L1-S1 ROM and IDP or total L1-S1 ROM and FJF was fitted in the TLIF model to calculate the relative total L1-S1 ROMs without an increase in IDP and FJF.

RESULTS

Compared with those of the intact model, the ROM, IDP, and FJF of the adjacent segments in the TLIF model increased by 12.6-28.9%, 0.1-6.8%, and 0-134.2%, respectively. As the total L1-S1 ROM increased, the IDP and FJF of each adjacent segment increased by varying degrees. The relative total L1-S1 ROMs in the TLIF model were 11.03°, 12.50°, 12.14°, and 9.82° in flexion, extension, lateral bending, and axial rotation, respectively.

CONCLUSIONS

The relative total L1-S1 ROMs after TLIF were determined, which decreased by 19.6-29.3% compared to the preoperative ones. Guiding the patients to perform postoperative waist activities within these specific ROMs, an increase in the IDP and FJF of adjacent segments may be effectively offset, thereby alleviating ASD.

Comparing the osteogenesis outcomes of different lumbar interbody fusions (A/O/X/T/PLIF) by evaluating their mechano-driven fusion processes

BACKGROUND

In lumbar interbody fusion (LIF), achieving proper fusion status requires osteogenesis to occur in the disc space. Current LIF techniques, including anterior, oblique, lateral, transforaminal, and posterior LIF (A/O/X/T/PLIF), may result in varying osteogenesis outcomes due to differences in biomechanical characteristics.

METHODS

A mechano-regulation algorithm was developed to predict the fusion processes of A/O/X/T/PLIF based on finite element modeling and iterative evaluations of the mechanobiological activities of mesenchymal stem cells (MSCs) and their differentiated cells (osteoblasts, chondrocytes, and fibroblasts). Fusion occurred in the grafting region, and each differentiated cell type generated the corresponding tissue proportional to its concentration. The corresponding osteogenesis volume was calculated by multiplying the osteoblast concentration by the grafting volume.

RESULTS

TLIF and ALIF achieved markedly greater osteogenesis volumes than did PLIF and O/XLIF (5.46, 5.12, 4.26, and 3.15 cm3, respectively). Grafting volume and cage size were the main factors influencing the osteogenesis outcome in patients treated with LIF. A large grafting volume allowed more osteoblasts (bone tissues) to be accommodated in the disc space. A small cage size reduced the cage/endplate ratio and therefore decreased the stiffness of the LIF. This led to a larger osteogenesis region to promote osteoblastic differentiation of MSCs and osteoblast proliferation (bone regeneration), which subsequently increased the bone fraction in the grafting space.

CONCLUSION

TLIF and ALIF produced more favorable biomechanical environments for osteogenesis than did PLIF and O/XLIF. A small cage and a large grafting volume improve osteogenesis by facilitating osteogenesis-related cell activities driven by mechanical forces.

Comprehensive modeling of annulus fibrosus: From biphasic refined characterization to damage accumulation under viscous loading

The annulus fibrosus (AF), a permeable, hydrated, and fiber-reinforced soft tissue, exhibits complex responses influenced by fluid pressure, osmotic pressure, and structural mechanics. Existing models struggle to comprehensively represent these intricate interactions and the heterogeneous solid responses within the AF. Additionally, the mechanisms driving differential damage accumulation between non-degenerative and degenerative intervertebral discs remain poorly understood. In this study, we introduce a biphasic-swelling damage model for the AF. We conceptually develop and rigorously validate this model through tissue-level tests employing various loading modes, consistently aligning model predictions with experimental data. Leveraging parametric geometric algorithms and custom Python scripts, we construct models simulating both non-degenerative and degenerative discs. Following calibration, we subject these models to viscous loading protocols. Our findings reveal the posterior AF's susceptibility to damage, contingent upon loading rate and water content. We elucidate the underlying mechanisms by examining the temporal evolution of fluid pressure, osmotic pressure, and the regionally dependent fiber network. This research presents a highly accurate model of the AF, providing valuable insights into disc damage. Future research endeavors should expand this model to incorporate ionic transport and diffusion, enabling a more profound exploration of intervertebral disc mechanobiology. This comprehensive model contributes to a better understanding of AF behavior and may inform therapeutic strategies for disc-related pathologies. STATEMENT OF SIGNIFICANCE: This research presents a comprehensive model of the annulus fibrosus (AF), a crucial component of the intervertebral disc that provides structural support and resists deformation. The study introduces a biphasic-swelling damage model for the AF and validates it through tissue-level tests. The model accounts for fluid pressure, osmotic pressure, and matrix mechanics, providing a more accurate representation of the AF's behavior. The study also investigates the differential damage accumulation between non-degenerative and degenerative discs, shedding light on the mechanisms driving disc degeneration. The findings have significant implications for medical treatments and interventions, as they highlight the posterior AF's susceptibility to damage. This research is of great interest to readers interested in biomechanics, tissue engineering, and medical treatments for disc degeneration.

Customized design and biomechanical property analysis of 3D-printed tantalum intervertebral cages

BACKGROUND

Intervertebral cages used in clinical applications were often general products with standard specifications, which were challenging to match with the cervical vertebra and prone to cause stress shielding and subsidence.

OBJECTIVE

To design and fabricate customized tantalum (Ta) intervertebral fusion cages that meets the biomechanical requirements of the cervical segment.

METHODS

The lattice intervertebral cages were customized designed and fabricated by the selective laser melting. The joint and muscle forces of the cervical segment under different movements were analyzed using reverse dynamics method. The stress characteristics of cage, plate, screws and vertebral endplate were analyzed by finite element analysis. The fluid flow behaviors and permeability of three lattice structures were simulated by computational fluid dynamics. Compression tests were executed to investigate the biomechanical properties of the cages.

RESULTS

Compared with the solid cages, the lattice-filled structures significantly reduced the stress of cages and anterior fixation system. In comparison to the octahedroid and quaddiametral lattice-filled cages, the bitriangle lattice-filled cage had a lower stress shielding rate, higher permeability, and superior subsidence resistance ability.

CONCLUSION

The inverse dynamics simulation combined with finite element analysis is an effective method to investigate the biomechanical properties of the cervical vertebra during movements.

Biomechanical differences between two different shapes of oblique lumbar interbody fusion cages on whether to add posterior internal fixation system: a finite element analysis

BACKGROUND

Oblique lateral lumbar fusion (OLIF) is widely used in spinal degeneration, deformity and other diseases. The purpose of this study was to investigate the biomechanical differences between two different shapes of OLIF cages on whether to add posterior internal fixation system, using finite element analysis.

METHODS

A complete three-dimensional finite element model is established and verified for L3-L5. Surgical simulation was performed on the verified model, and the L4-L5 was the surgical segment. A total of the stand-alone group (Model A1, Model B1) and the BPSF group (Model A2, Model B2) were constructed. The four OLIF surgical models were: A1. Stand-alone OLIF with a kidney-shaped Cage; B1. Stand-alone OLIF with a straight cage; A2. OLIF with a kidney-shaped cage + BPSF; B2. Stand-alone OLIF with a straight cage + BPSF, respectively. The differences in the range of motion of the surgical segment (ROM), equivalent stress peak of the cage (ESPC), the maximum equivalent stress of the endplate (MESE) and the maximum stress of the internal fixation (MSIF) were compared between different models.

RESULTS

All OLIF surgical models showed that ROM declines between 74.87 and 96.77% at L4-L5 operative levels. The decreasing order of ROM was Model A2 > Model B2 > Model A1 > Model A2. In addition, the ESPC and MESE of Model A2 are smaller than those of other OLIF models. Except for the left-bending position, the MSIF of Model B2 increased by 1.51-16.69% compared with Model A2 in each position. The maximum value of MESE was 124.4 Mpa for Model B1 in the backward extension position, and the minimum value was 7.91 Mpa for Model A2 in the right rotation. Stand-alone group showed significantly higher ROMs and ESPCs than the BPSF group, with maximum values of 66.66% and 70.59%. For MESE, the BPSF group model can be reduced by 89.88% compared to the stand-alone group model.

CONCLUSIONS

Compared with the traditional straight OLIF cage, the kidney-shaped OLIF cage can further improve the stability of the surgical segment, reduce ESPC, MESE and MSIF, and help to reduce the risk of cage subsidence.

Comparison between Three-Dimensional Printed Titanium and PEEK Cages for Cervical and Lumbar Interbody Fusion: A Prospective Controlled Trial

OBJECTIVES

The three-dimensional printing titanium (3DPT) cage with excellent biomechanical properties and osseointegration capabilities has been initially used in spinal fusion, while the polyetheretherketone (PEEK) cage, a bioinert material device, has been a widely used for decades with relatively excellent clinical outcomes. This study was performed to investigate the early radiographic and clinical outcomes of 3DPT cage versus PEEK cage in patients undergoing anterior cervical discectomy and fusion (ACDF) and transforaminal lumbar interbody fusion (TLIF).

METHODS

This prospective controlled trial, from December 2019 to June 2022, included patients undergoing ACDF and TLIF with 3DPT cages and compared them to patients using PEEK cages for treating spinal degenerative disorders. The outcome measures included radiographic parameters (intervertebral height [IH], subsidence, fusion status, and bone-cage interface contact) and clinical outcomes (Japanese Orthopaedic Association [JOA], Neck Disability Index [NDI], Oswestry Disability Index [ODI], Short Form 12-Item Survey [SF-12], Visual Analog Scale [VAS], and Odom's criteria). Student's independent samples t test and Pearson's chi-square test were used to compare the outcome measures between the two groups before surgery and at 1 week, 3 and 6 months after surgery.

RESULTS

For the patients undergoing ACDF, the 3DPT (18 patients/[26 segments]) and PEEK groups (18 patients/[26 segments]) had similar fusion rates at 3 months and 6 months follow-up (3 months: 96.2% vs. 83.3%, p = 0.182; 6 months: 100% vs. 91.7%, p = 0.225). The subsidence in the 3DPT group was significantly lower than that in the PEEK group (3 months: 0.4 ± 0.2 mm vs. 0.9 ± 0.7 mm p = 0.004; 6 months: 0.7 ± 0.3 mm vs. 1.5 ± 0.8 mm, p < 0.001). 3DPT and PEEK cage all achieved sufficient contact with the cervical endplates. For the patients undergoing TLIF, the 3DPT (20 patients/[26 segments]) and PEEK groups (20 patients/[24 segments]) had no statistical difference in fusion rate (3 months: 84.6% vs. 58.3%, p = 0.059; 6 months: 92.3% vs. 75%, p = 0.132). The subsidence was lower than that in the PEEK group without significantly difference (3 months: 0.9 ± 0.7 mm vs.1.2 ± 0.9 mm p = 0.136; 6 months: 1.6 ± 1.0 mm vs. 2.0 ± 1.0 mm, p = 0.200). At the 3-month follow-up, the bone-cage interface contact of the 3DPT cage was significantly better than that of the PEEK cage (poor contact: 15.4% vs. 75%, p < 0.001). The values of UAR were higher in the 3DPT group than in the PEEK group during the follow-up in cervical and lumbar fusion, there were more statistical differences in lumbar fusion. There were no significant differences in the clinical assessment between 3DPT or PEEK cage in spinal fusion.

CONCLUSION

The 3DPT cage and PEEK cage can achieve excellent clinical outcomes in cervical and lumbar fusion. The 3DPT cage has advantage in fusion quality, subsidence severity, and bone-cage interface contact than PEEK cage.

A swelling-based biphasic analysis on the quasi-static biomechanical behaviors of healthy and degenerative intervertebral discs

BACKGROUND AND OBJECTIVE

The degeneration of intervertebral discs is significantly dependent of the changes in tissue composition ratio and tissue structure. Up to the present, the effects of degeneration on the quasi-static biomechanical responses of discs have not been well understood. The goal of this study is to quantitatively analyze the quasi-static responses of healthy and degenerative discs.

METHODS

Four biphasic swelling-based finite element models are developed and quantitatively validated. Four quasi-static test protocols, including the free-swelling, slow-ramp, creep and stress-relaxation, are implemented. The double Voigt and double Maxwell models are further used to extract the immediate (or residual), short-term and long-term responses of these tests.

RESULTS

Simulation results show that both the swelling-induced pressure in the nucleus pulposus and the initial modulus decrease with degeneration. In the free-swelling test of discs possessing healthy cartilage endplates, simulation results show that over 80% of the total strain is contributed by the short-term response. The long-term response is dominant for discs with degenerated permeability in cartilage endplates. For the creep test, over 50% of the deformation is contributed by the long-term response. In the stress-relaxation test, the long-term stress contribution occupies approximately 31% of total response and is independent of degeneration. Both the residual and short-term responses vary monotonically with degeneration. In addition, both the glycosaminoglycan content and permeability affect the engineering equilibrium time constants of the rheologic models, in which the determining factor is the permeability.

CONCLUSIONS

The content of glycosaminoglycan in intervertebral soft tissues and the permeability of cartilage endplates are two critical factors that affect the fluid-dependent viscoelastic responses of intervertebral discs. The component proportions of the fluid-dependent viscoelastic responses depend also strongly on test protocols. In the slow-ramp test, the glycosaminoglycan content is responsible for the changes of the initial modulus. Since existing computational models simulate disc degenerations only by altering disc height, boundary conditions and material stiffness, the current work highlights the significance of biochemical composition and cartilage endplates permeability in the biomechanical behaviors of degenerated discs.

Biomechanical Analysis of Lumbar Interbody Fusion Cages With Various Elastic Moduli in Osteoporotic and Non-osteoporotic Lumbar Spine: A Finite Element Analysis

STUDY DESIGN

Finite element analysis (FEA).

OBJECTIVE

This study aimed to explore the effects of cage elastic modulus (Cage-E) on the endplate stress in different bone conditions: osteoporosis (OP) and non-osteoporosis (non-OP). We also explored the correlation between endplate thickness and endplate stress.

METHOD

The FEA models of L4-L5 with lumbar interbody fusion were designed to access the effects of Cage-E on the endplate stress in different bone conditions. Two groups of the Young's moduli of bony structure were assigned to simulate the conditions of OP and non-OP, and the bony endplates were analyzed in 2 kinds of thicknesses: .5 mm and 1.0 mm, with the insertion of cages with different Young's moduli including .5, 1.5, 3, 5, 10, and 20 GPa. After model validation, an axial compressive load of 400 N and a flexion/extension moment of 7.5Nm was performed on the superior surface of L4 vertebral body in order to analyze the distribution of stress.

RESULT

The maximum Von Mises stress in the endplates increased by up to 100% in the OP model compared with non-OP model under the same condition of cage-E and endplate thickness. In both OP and non-OP models, the maximum endplate stress decreased as the cage-E decreased, but the maximum stress in the lumbar posterior fixation increased as the cage-E decreased. Thinner endplate thickness was associated with increased endplate stress.

CONCLUSION

The endplate stress is higher in osteoporotic bone than non-osteoporotic bone, which explains part of the mechanism of OP-related cage subsidence. It is reasonable to reduce the endplate stress by reducing the cage-E, but we should balance the risk of fixation failure. Endplate thickness is also important when evaluating the cage subsidence risk.

Device profile of the FlareHawk interbody fusion system, an endplate-conforming multi-planar expandable lumbar interbody fusion cage

INTRODUCTION

The FlareHawk Interbody Fusion System is a family of lumbar interbody fusion devices (IBFDs) that include FlareHawk7, FlareHawk9, FlareHawk11, TiHawk7, TiHawk9, and TiHawk11. These IBFDs offer a new line of multi-planar expandable interbody devices designed to provide mechanical stability, promote arthrodesis, and allow for restoration of disc height and lordosis through a minimal insertion profile during standard open and minimally invasive posterior lumbar fusion procedures. The two-piece interbody cage design consists of a PEEK outer shell that expands in width, height, and lordosis with the insertion of a titanium shim. Once expanded, the open architecture design allows for ample graft delivery into the disc space.

AREAS COVERED

The design and unique features of the FlareHawk family of expandable fusion cages are described. The indications for their use are discussed. Early clinical and radiographic outcome studies using the FlareHawk Interbody Fusion System are reviewed, and properties of competitor products are outlined.

EXPERT OPINION

The FlareHawk multi-planar expandable interbody fusion cage is unique amongst the many lumbar fusion cages currently on the market. The multi-planar expansion, open architecture, and adaptive geometry set it apart from its competitors.

Roles of irregularity of pore morphology in osteogenesis of Voronoi scaffolds: From the perspectives of MSC adhesion and mechano-regulated osteoblast differentiation

Bone scaffolds designed based on the Voronoi-tessellation algorithm have been increasingly studied owing to their structural similarity with natural cancellous bone. The irregularity of pore morphology (IPM) influences the osteogenesis efficiency of Voronoi scaffolds since it may alter the static and hydromechanical microenvironments for the initial adhesion and mechano-regulated osteoblast differentiation (MrOD) of mesenchymal stem cells (MSCs). In this work, animal experiments were conducted to explore the relationship between IPM and osteogenesis efficiency in Voronoi scaffolds. A computational fluid dynamics (CFD) analysis based on discrete phase models was performed to predict the efficiency of MSC adhesion in different IPMs. Another combined finite element and CFD analysis based on the mechano-regulation algorithm was performed to predict the influence of IPM on the MrOD of the adhesive MSCs. The results showed that the osteogenesis efficiency of the Voronoi scaffolds increased as the IPM rose from low to moderate and then dropped as the IPM further rose. Same trends were also found in the MSC adhesion and MrOD, which caused by the changes of strain tensors on the strut surface and the tortuosity and fluid velocity of the fluid pathway. Moderate IPM induced the highest osteogenesis efficiency owing to its highest efficiencies of MSC adhesion and MrOD. This work identified the optimal IPM for the osteogenesis of Voronoi scaffolds and clarified its biomechanical mechanisms from the adhesion and mechano-regulated differentiation of MSCs, which is of great importance for guiding Voronoi scaffold design when it is used for bone defect repair.

Effect of Interbody Implants on the Biomechanical Behavior of Lateral Lumbar Interbody Fusion: A Finite Element Study

Porous titanium interbody scaffolds are growing in popularity due to their appealing advantages for bone ingrowth. This study aimed to investigate the biomechanical effects of scaffold materials in both normal and osteoporotic lumbar spines using a finite element (FE) model. Four scaffold materials were compared: Ti6Al4V (Ti), PEEK, porous titanium of 65% porosity (P65), and porous titanium of 80% porosity (P80). In addition, the range of motion (ROM), endplate stress, scaffold stress, and pedicle screw stress were calculated and compared. The results showed that the ROM decreased by more than 96% after surgery, and the solid Ti scaffold provided the lowest ROM (1.2-3.4% of the intact case) at the surgical segment among all models. Compared to solid Ti, PEEK decreased the scaffold stress by 53-66 and the endplate stress by 0-33%, while porous Ti decreased the scaffold stress by 20-32% and the endplate stress by 0-32%. Further, compared with P65, P80 slightly increased the ROM (<0.03°) and pedicle screw stress (<4%) and decreased the endplate stress by 0-13% and scaffold stress by approximately 18%. Moreover, the osteoporotic lumbar spine provided higher ROMs, endplate stresses, scaffold stresses, and pedicle screw stresses in all motion modes. The porous Ti scaffolds may offer an alternative for lateral lumbar interbody fusion.

A finite element study on the effects of follower load on the continuous biomechanical responses of subaxial cervical spine

In spine biomechanics, follower loads are used to mimic the in vivo muscle forces acting on a human spine. However, the effects of the follower load on the continuous biomechanical responses of the subaxial cervical spines (C2-T1) have not been systematically clarified. This study aims at investigating the follower load effects on the continuous biomechanical responses of C2-T1. A nonlinear finite element model is reconstructed and validated for C2-T1. Six levels follower loads are considered along the follower load path that is optimized through a novel range of motion-based method. A moment up to 2 Nm is subsequently superimposed to produce motions in three anatomical planes. The continuous biomechanical responses, including the range of motion, facet joint force, intradiscal pressure and flexibility are evaluated for each motion segment. In the sagittal plane, the change of the overall range of motion arising from the follower loads is less than 6%. In the other two anatomical planes, both the magnitude and shape of the rotation-moment curves change with follower loads. At the neutral position, over 50% decrease in flexibility occurs as the follower load increases from zero to 250 N. In all three anatomical planes, over 50% and 30% decreases in flexibility occur in the first 0.5 Nm for small (≤100 N) and large (≥150 N) follower loads, respectively. Moreover, follower loads tend to increase both the facet joint forces and the intradiscal pressures. The shape of the intradiscal pressure-moment curves changes from nonlinear to roughly linear with increased follower load, especially in the coronal and transverse planes. The results obtained in this work provide a comprehensive understanding on the effects of follower load on the continuous biomechanical responses of the C2-T1.