Performance of concrete containing recycled masks used for personal protection during coronavirus pandemic

Experimental Study on the Mechanical Properties of Disposable Mask Waste-Reinforced Gangue Concrete

This paper is grounded on the following information: (1) Disposable masks primarily consist of polypropylene fiber, which exhibits excellent flexibility. (2) China has extensive coal gangue deposits that pose a significant environmental hazard. (3) Coal gangue concrete exhibits greater fragility compared to regular concrete and demonstrates reduced resistance to deformation. With the consideration of environmental conservation and resource reutilization, a preliminary concept suggests the conversion of discarded masks into fibers, which can be blended with coal gangue concrete to enhance its mechanical characteristics. In this paper, the stress-strain law of different mask fiber-doped coal gangue concrete (DMGC) under uniaxial compression is studied when the matrix strength is C20 and C30, and the effect of mask fiber content on the mechanical behavior and energy conversion relationship of coal gangue concrete is analyzed. The experimental results show that when the content of mask fiber is less than 1.5%, the strength, elastic modulus, deformation resistance, and energy dissipation of the concrete increase with mask fiber content. When the amount of mask fiber is more than 1.5%, because the tensile capacity and energy dissipation level of concrete produced by the mask fiber cannot compensate for the compression and deformation resistance of concrete of the same quantity and because excess fiber is difficult to evenly mix in the concrete, there are pore defects in concrete, which decreases the concrete strength due to the increase in mask fiber. Therefore, adding less than 1.5% mask fiber helps to improve the ductility, toughness, impermeability, and oxidation and control the cracking of coal gangue concrete. Based on Weibull theory, a constitutive model of DMGC is established, which fits well with the results of a uniaxial test, providing support for understanding the mechanical law of mask fiber-doped concrete.

Recycling facemasks into civil construction material to manage waste generated during COVID-19

Growing plastic pollution in the context of COVID-19 has caused significant challenges, exacerbating this already out-of-control issue. The pandemic has considerably boosted the demand for personal protective equipment (PPE), such as facemasks and gloves, all over the globe, and mismanaging this growing plastic pollution has harmed the environment and wildlife significantly. To mitigate negative environmental impacts, it is necessary to develop and implement effective waste management strategies. This present study estimated the daily facemask generation throughout the pandemic in Iran based on the distribution of urban and rural populations and, likewise, the daily generation of hand gloves in the COVID-19 era and the amount of medical waste generated by COVID-19 patients were calculated. In the next step, the quantities of discarded facemasks dumped into the Caspian Sea, the Persian Gulf, and the Gulf of Oman from the coastal cities were determined. Finally, the innovative alternatives for repurposing discarded facemasks in civil construction materials such as concrete, pavement, and partition wall panel were discussed.

Recycling COVID-19 health care wastes in bitumen modification: a case of disposable medical gloves

Disposable medical gloves (DMGs) have long been used to mitigate the risk of direct exposure to diverse microorganisms and body fluids; hence, they are a critical weapon to protect patients and healthcare staff from infectious diseases. Measures to control the spread of COVID-19 have sparked the production of an excessive number of DMGs, most of which are eventually being disposed of in landfills. Untreated DMGs in landfills do not only pose a direct risk of transmitting coronavirus and other pathological germs but also pollute air, water, and soil dramatically. As a healthier alternative, recycling discarded polymer-rich DMGs into bitumen modification is considered to be a prospective waste management strategy applicable to the asphalt pavement industry. In this study, this conjecture is tested by examining two common DMGs - latex gloves and vinyl gloves - at four different percentages (1%, 2%, 3%, and 4% by weight). The morphological characteristics of DMG-modified specimens were inspected by using a high-definition scanning electron microscope (SEM) equipped with an energy dispersive X-ray analyzer (EDX). A wide range of laboratory tests including penetration, softening point temperature, ductility, and elastic recovery were undertaken to evaluate the impact of waste gloves on the conventional engineering properties of bitumen. Moreover, viscoelastic behavior and modification processing were studied by conducting the dynamic shear rheometer (DSR) test and the Fourier transform infrared spectroscopy (FTIR) analysis. Test results have revealed the outstanding potential of recycled DMG waste for modifying neat asphalt binder. More specifically, bitumens modified with 4% latex glove and 3% vinyl glove were seen as capable of superiorly withstanding permanent deformations caused by heavy axle loads at high service temperatures. Furthermore, it has been shown that 1.2 tons of modified binder would embed approximately 4000 pairs of recycled DMGs. This study shows that DMG waste can be used as a viable modifier, which would help open a new avenue for mitigating the environmental pollution arising from the COVID-19 pandemic.

Property assessment of an eco-friendly mortar reinforced with recycled mask fiber derived from COVID-19 single-use face masks

Wearing a face mask is strongly advised to prevent the spread of the virus causing the COVID-19 pandemic, though masks have produced a tremendous amount of waste. As masks contain polypropylene and other plastics products, total degradation is not achievable, and masks may remain in the form of microplastics for several years in the environment. Therefore, this urgent issue ought to be addressed by properly handling waste face masks to limit their environmental impact. In relation to this goal, a novel application of recycled mask fiber (MF) derived from COVID-19 single-use surgical face masks (i.e., shredded mask fiber-SMF and cut mask fiber-CMF) has been undertaken. Eighteen mortar mixes (9 for water and 9 for 10% CO₂ concentration curing) were fabricated at 0%, 0.5%, 1.0%, 1.5%, and 2.0% of both SMF and CMF by volume of ordinary Portland cement-based mortar. The compressive strength, flexural strength, ultrasonic pulse velocity, shrinkage, carbonation degree, permeable voids, and water absorption capabilities were assessed. The outcomes reveal that the compressive strength decreased with an increased percentage of MFs due to increased voids of the mixes with MFs as compared to a control mix. In contrast, significantly higher flexural strength was noted for the mortar with MFs, which is augmented with an increased percentage of MFs. Furthermore, the inclusion of MFs decreased the shrinkage of the mortar compared to the control mix. It was also found that MFs dramatically diminished the water absorption rate compared to the control mix, which reveals that MFs can enhance the durability of the mortar.

Smart waste management perspective of COVID-19 healthy personal protective materials in concrete for decorative landscape pavements and artificial rocks

This paper presents a new method for determining the effect of healthy personal protective material (HPPM) stripes, such as surgical masks, protective suits, and overhead and foot covers, on the durability and physicomechanical characteristics of concrete for use in architectural forms. Because of the current global epidemic caused by coronavirus (COVID-19), the use of HPPM, such as surgical masks, protective suits, and overhead and foot covers, has increased considerably. COVID-19's second and third waves are currently affecting various countries, necessitating the use of facemasks (FM). Consequently, millions of single FM have been discharged into the wild, washing up on beaches, floating beneath the seas, and ending up in hazardous locations. The effect of stripe fibers on the physicomechanical characteristics of concrete, such as the workability, Uniaxial Compressive Strength UCS, flexural strength, impact strength, spalling resistance, abrasion resistance, sorptivity, Water absorption Sw, porosity (ηe), water penetration, permeability, and economic and eco-friendly aspects, need to be determined. With a focus on HPPM, especially single-use facemasks, this study investigated an innovative way to incorporate pandemic waste into concrete structures. Scanning electron microscope and X-ray diffraction patterns were employed to analyze the microstructures and interfacial transition zones and to identify the elemental composition. The HPPM had a pore-blocking effect, which reduced the permeability and capillary porosity. Additionally, the best concentrations of HPPM, particularly of masks, were applied by volume at 0, 1, 1.5, 2.0, and 2.5%. The use of mixed fibers from different HPPMs increased the strength and overall performance of concrete samples. The tendency of growing strength began to disappear at approximately 2%. The results of this investigation showed that the stripe content had no effect on the compressive strength. However, the stripe is critical for determining the flexural strength of concrete. The UCS increased steadily between 1 and 1.5% before falling marginally at 2.5%, which indicates that incorporating HPPM into concrete had a significant impact on the UCS of the mixture. The addition of HPPM to the mixtures considerably modified the failure mode of concrete from brittle to ductile. Water absorption in hardened concrete is reduced when HPPM stripes and fibers were added separately in low-volume fractions to the concrete mixture. The concrete containing 2% HPPM fibers had the lowest water absorption and porosity percentage. The HPPM fibers were found to act as bridges across cracks, enhancing the transfer capability of the matrices. From a technological and environmental standpoint, this study found that using HPPM fibers in the production of concrete is viable.

Disposal and resource utilization of waste masks: a review

Waste masks pose a serious threat to the environment, including marine plastic pollution and soil pollution risks caused by landfills since the outbreak of COVID-19. Currently, numerous effective methods regarding disposal and resource utilization of waste masks have been reported, containing physical, thermochemical, and solvent-based technologies. As for physical technologies, the mechanical properties of the mask-based materials could be enhanced and the conductivity or antibacterial activity was endowed by adding natural fibers or inorganic nanoparticles. Regarding thermochemical technologies, catalytic pyrolysis could yield considerable hydrogen, which is an eco-friendly resource, and would mitigate the energy crisis. Noticeably, the solvent-based technology, as a more convenient and efficient method, was also considered in this paper. In this way, soaking the mask directly in a specific chemical reagent changes the original structure of polypropylene and obtains multi-functional materials. The solvent-based technology is promising in the future with the researches of sustainable and universally applicable reagents. This review could provide guidance for utilizing resources of waste masks and address the issues of plastic pollution.

Upcycling face mask wastes generated during COVID-19 into value-added engineering materials: A review

Billions of disposable face masks (i.e., single-use masks) are used and discarded worldwide monthly due to the COVID-19 outbreak. The immethodical disposal of these polymer-based wastes containing non-biodegradable constituents (e.g., polypropylene) has provoked marked and severe damage to the ecosystem. Meanwhile, their ever-growing usage significantly strains the present-day waste management measures such as landfilling and incineration, resulting in large quantities of used face-covering masks landing in the environment as importunate contaminants. Hence, alternative waste management strategies are crucially demanded to decrease the negative impacts of face mask contamination. In this venue, developing high-yield, effective, and green routes toward recycling or upcycling face mask wastes (FMWs) into value-added materials is of great importance. While existing recycling processes assist the traditional waste management, they typically end up in materials with downgraded physicochemical, structural, mechanical, and thermal characteristics with reduced values. Therefore, pursuing potential economic upcycling processes would be more beneficial than waste disposal and/or recycling processes. This paper reviews recent advances in the FMWs upcycling methods. In particular, we focus on producing value-added materials via various waste conversion methods, including carbonization (i.e., extreme pyrolysis), pyrolysis (i.e., rapid carbonization), catalytic conversion, chemical treatment, and mechanical reprocessing. Generally, the upcycling methods are promising, firming the vital role of managing FMWs' fate and shedding light on the road of state-of-the-art materials design and synthesis.

Recent advances and challenges in recycling and reusing biomedical materials

Medical waste has increased in the past 3 years as a result of the coronavirus disease 2019 (COVID-19) pandemic. This condition is expected to exacerbate due to the growing healthcare markets and aging population, posing health threats to the public via environmental footprints. To alleviate these impacts, there is an urgent need for medical waste management. This article highlights the drawbacks of current disposal methods and the potential of medical waste reuse and recycling, emphasizing the processes, materials, and chemistry involved in each practice. Further discussion is provided on the chemical and mechanical recycling of plastics as the dominating material in biomedical applications, and possible strategies and challenges in recycling and reusing biomedical materials are explored in this review.

Effective recycling of disposable medical face masks for sustainable green concrete via a new fiber hybridization technique

Global public response to the COVID-19 (SARS-CoV-2) pandemic is highly focused on human health. However, conservationists have cautioned of unprecedented threats to the natural environment from a new type of non-biodegradable microplastic waste resulting from extensive use of disposable medical face masks (DMFMs). Thus, this waste must be recycled in an eco-friendly manner on an urgent basis. In this research, we developed a new environmentally friendly recycling technique using waste DMFMs in sustainable green concrete. More explicitly, a new fiber hybridization approach has been introduced in which two types of fibers namely DMFM fiber and basalt fiber (BF) were incorporated into fiber reinforced recycled aggregate concrete (FRAC). The volume fractions of DMFM fiber were 0%, 0.1%, and 0.2% and the volume fractions of BF were 0%, 0.25%, and 0.5%. In addition, two mineral admixtures (fly ash and ground granulated blast furnace slag) were also used. Test results indicated increase of approximately 12% in compressive strength, 26% in split tensile strength, and 60% in flexural strength of FRAC containing hybrid fibers and mineral admixtures. The density and ultra-sonic pulse velocity (UPV) of DMFM fiber- and BF-modified FRAC ranged from 2406-2433 kg/m³ and 4502-4541 m/s, respectively, which meets structural concrete requirements. The water absorption rate gradually increased with an increase in the volume fractions of fibers but remained within the allowable water absorption limit for construction materials. Lastly, the microstructure investigation indicated excellent concrete quality, improved interfacial transition zones (ITZs), and good compatibility of host concrete matrix with both DMFM fiber and BF that correlates well with the experimental results reported in this study.

Development and characterization of novelly grown fire-resistant fungal fibers

This study conducted a comprehensive characterization and analyses on the fire-resistant behaviors of novel fungal fibers grown with substrate containing Silica (Si) source at multiple scales. At micro-scale, the results of SEM showed that silica affected the physiological activities of fungi, with the extent of effects depending upon its concentration. Fourier-transform infrared (FTIR) spectra displayed the existence of Si–O–C chemical bonds in fungal fibers grown with Si source, indicating that Si source becomes a part of the structure of fungal fibers. Thermogravimetric analysis (TGA) and Microscale combustion calorimetry (MCC) of fungal fibers exhibit an early thermal decomposition of non-combustible components, which will potentially help release the thermal stress and mitigation of spalling when used in concrete. Compared with polypropylene (PP) fibers, fungal fibers have a lower thermal degradation rate, a higher residual weight, a lower heat release peak temperature, and less total heat of combustion; all of these indicate improved thermal stability and fire resistance, and a lower rate of function loss in case of a fire. Additionally, the thermal stability and fire resistance of fungal fibers were improved with the increase of Si source concentration in the nutrition medium. For example, addition of 2% Si source in the feeding substrate leads to a 23.21% increase in residual weight in TGA, and a 23.66 W/g decrease in peak heat release rate as well as a 2.44 kJ/g reduction in total heat of combustion in MCC. At laboratory scale, compared with PP fibers, fungal fibers grown with 2% Si source have a higher residual weight of 40.40%, a higher ignition temperature of 200.50 °C, and a declined flame height of 11.64 mm in real fire scenarios. Furthermore, only in the fungal fibers grown with Si source, partial burning occurred. In post-fire conditions, the microstructure of residual char from fungal fibers grown with higher content of Si source became denser, which would lead to a reduction of the fuel vapor release and heat transfer. FTIR spectra of residual char demonstrated that fungal fibers grown with Si source formed more stable chemical bonds with higher heat of chemical bond formation, contributing to improved thermal stability and fire resistance. Therefore, compared with traditional fibers used for fiber reinforced concrete, incorporating the new natural grown fibers will potentially further improve the fire resistance of concrete and mitigate the concrete spalling.