Photoelectron-photoion coincidence spectroscopy for multiplexed detection of intermediate species in a flame

CO Cofeeding Affects Product Distribution in CH3Cl Coupling over ZSM-5 Zeolite: Pressure Twists the Plot

C1 coupling reactions over zeolite catalysts are central to sustainable chemical production strategies. However, questions persist regarding the involvement of CO in ketene formation, and the impact of this elusive oxygenate intermediate on reactivity patterns. Using operando photoelectron photoion coincidence spectroscopy (PEPICO), we investigate the role of CO in methyl chloride conversion to hydrocarbons (MCTH), a prospective process for methane valorization with a reaction network akin to methanol to hydrocarbons (MTH) but without oxygenate intermediates. Our findings reveal the transformative role of CO in MCTH at the low pressures, inducing ketene formation in MCTH and boosting olefin production, confirming the Koch carbonylation step in the initial stages of C1 coupling. We uncover pressure-dependent product distributions driven by CO-induced ketene formation, and its subsequent desorption from the zeolite surface, which is enhanced at low pressure. Inspired by the above results, extension of the co-feeding approach to CH3OH as another simple oxygenate showcases the additional potential for improved catalyst stability in MCTH at ambient pressure.

Conformer-Specific Photoelectron Spectroscopy of Carbonic Acid: H2CO3

Carbonic acid (H2CO3) is a fundamental species in biological, ecological, and astronomical systems. However, its spectroscopic characterization is incomplete because of its reactive nature. The photoionization (PI) and the photoion mass-selected threshold photoelectron (ms-TPE) spectra of H2CO3 were obtained by utilizing vacuum ultraviolet (VUV) synchrotron radiation and double imaging photoelectron photoion coincidence spectroscopy. Two carbonic acid conformers, namely, cis-cis and cis-trans, were identified. Experimental adiabatic ionization energies (AIEs) of cis-cis and cis-trans H2CO3 were determined to be 11.27 ± 0.02 and 11.18 ± 0.03 eV, and the cation enthalpies of formation could be derived as ΔfH°0K = 485 ± 2 and 482 ± 3 kJ mol-1, respectively. The cis-cis conformer shows intense peaks in the ms-TPES that are assigned to the C=O/C-OH stretching mode, while the cis-trans conformer exhibits a long progression to which two C=O/C-OH stretching modes contribute. The TPE spectra allow for the sensitive and conformer-selective detection of carbonic acid in terrestrial experiments to better understand astrochemical reactions.

Analysis of the volatile monoterpene composition of citrus essential oils by photoelectron spectroscopy employing continuously monitored dynamic headspace sampling

A new photoelectron spectroscopic method permitting a quantitative analysis of the volatile headspace of several essential oils is presented and discussed. In particular, we focus on the monoterpene compounds, which are known to be the dominant volatile components in many such oils. The photoelectron spectra of the monoterpene constituents may be effectively isolated by accepting for analysis only those electrons that accompany the production of m/z = 136 ions, and by using low photon energies that restrict cation fragmentation. The monoterpene isomers are then identified and quantified by regression modelling using a library of terpene standard spectra. An advantage of this approach is that pre-concentration of the volatile vapour is not required, and all steps are performed at ambient temperature, avoiding the possible deleterious effects (such as isomerisation/decomposition) that may sometimes arise in gas chromatographic (GC) procedures. As a proof-of-principle demonstration, three citrus oils (lemon, lime, bergamot) are analysed with this approach and the results are compared with reported GC composition profiles obtained for these oils. Potential advantages of the methodology that include multiplex detection and real-time, in situ analysis are identified and discussed. Alternative and faster experimental implementations concerning laboratory-based ionization and detection schemes are proposed and considered, as is the possibility of a straightforward extension towards simultaneous determination of enantiomeric excesses.

Combustion, Chemistry, and Carbon Neutrality

Combustion is a reactive oxidation process that releases energy bound in chemical compounds used as fuels─energy that is needed for power generation, transportation, heating, and industrial purposes. Because of greenhouse gas and local pollutant emissions associated with fossil fuels, combustion science and applications are challenged to abandon conventional pathways and to adapt toward the demand of future carbon neutrality. For the design of efficient, low-emission processes, understanding the details of the relevant chemical transformations is essential. Comprehensive knowledge gained from decades of fossil-fuel combustion research includes general principles for establishing and validating reaction mechanisms and process models, relying on both theory and experiments with a suite of analytic monitoring and sensing techniques. Such knowledge can be advantageously applied and extended to configure, analyze, and control new systems using different, nonfossil, potentially zero-carbon fuels. Understanding the impact of combustion and its links with chemistry needs some background. The introduction therefore combines information on exemplary cultural and technological achievements using combustion and on nature and effects of combustion emissions. Subsequently, the methodology of combustion chemistry research is described. A major part is devoted to fuels, followed by a discussion of selected combustion applications, illustrating the chemical information needed for the future.

Operando PEPICO unveils the catalytic fast pyrolysis mechanism of the three methoxyphenol isomers

The development of lignin valorization processes such as catalytic fast pyrolysis (CFP) to produce fine chemicals and fuels leads to a more sustainable future. The implementation of CFP is enabled by understanding the chemistry of lignin constituents, which, however, requires thorough mechanistic investigations by detecting reactive species. In this contribution, we investigate the CFP of the three methoxyphenol (MP) isomers over H-ZSM-5 utilizing vacuum ultraviolet synchrotron radiation and operando photoelectron photoion coincidence (PEPICO) spectroscopy. All isomers demethylate at first to yield benzenediols, from which dehydroxylation reactions proceed to produce phenol and benzene. Additional pathways to form benzene proceed over cyclopentadiene, methylcyclopentadiene, and fulvene intermediates. The detection of trace amounts of methanol in the product stream suggests a demethoxylation reaction to yield phenol. Guaiacol (2- or ortho-MP) exhibits slightly higher reactivity compared to 3-MP and 4-MP, due to the formation of the fulvenone ketene, which opens additional routes to benzene and phenol. When compared to benzenediol catalytic pyrolysis, the additional methyl group in MP leads to high conversion at lower reactor temperatures, which is mostly owed to the lower H₃C–O vs. H–O bond energy and the possibility to demethoxylate to produce phenol.

Demethylation, demethoxylation and fulvenone ketene formation determine the reactivity of methoxyphenols over H-ZSM-5 to yield phenols, benzene and toluene. Intermediates are isomer-selectively detected utilizing threshold photoelectron spectroscopy.

First-Generation Organic Reaction Intermediates in Zeolite Chemistry and Catalysis

Zeolite chemistry and catalysis are expected to play a decisive role in the next decade(s) to build a more decentralized renewable feedstock-dependent sustainable society owing to the increased scrutiny over carbon emissions. Therefore, the lack of fundamental and mechanistic understanding of these processes is a critical "technical bottleneck" that must be eliminated to maximize economic value and minimize waste. We have identified, considering this objective, that the chemistry related to the first-generation reaction intermediates (i.e., carbocations, radicals, carbenes, ketenes, and carbanions) in zeolite chemistry and catalysis is highly underdeveloped or undervalued compared to other catalysis streams (e.g., homogeneous catalysis). This limitation can often be attributed to the technological restrictions to detect such "short-lived and highly reactive" intermediates at the interface (gas-solid/solid-liquid); however, the recent rise of sophisticated spectroscopic/analytical techniques (including under in situ/operando conditions) and modern data analysis methods collectively compete to unravel the impact of these organic intermediates. This comprehensive review summarizes the state-of-the-art first-generation organic reaction intermediates in zeolite chemistry and catalysis and evaluates their existing challenges and future prospects, to contribute significantly to the "circular carbon economy" initiatives.

High-Resolution Double Velocity Map Imaging Photoelectron Photoion Coincidence Spectrometer for Gas-Phase Reaction Kinetics

We present a new photoelectron photoion coincidence (PEPICO) spectrometer that combines high mass resolution of cations with independently adjustable velocity map imaging of both cations and electrons. We photoionize atoms and molecules using fixed-frequency vacuum ultraviolet radiation. Mass-resolved photoelectron spectra associated with each cation's mass-to-charge ratio can be obtained by inversion of the photoelectron image. The mass-resolved photoelectron spectra enable kinetic time-resolved probing of chemical reactions with isomeric resolution using fixed-frequency radiation sources amenable to small laboratory settings. The instrument accommodates a variety of sample delivery sources to explore a broad range of physical chemistry. To demonstrate the time-resolved capabilities of the instrument, we study the 193 nm photodissociation of SO₂ via the C̃(¹B₂) ← X̃(¹A₁) transition. In addition to the well-documented O(³P_j) + SO(³Σ^-) channel, we observe direct evidence for a small yield of S(³P_j) + O₂(³Σ_g^-) as a primary photodissociation product channel, which may impact sulfur mass-independent fractionation chemistry.

Gas-phase aluminium acetylacetonate decomposition: revision of the current mechanism by VUV synchrotron radiation

Although aluminium acetylacetonate, Al(C5H7O2)3, is a common precursor for chemical vapor deposition (CVD) of aluminium oxide, its gas-phase decomposition is not well-known. Here, we studied its thermal decomposition in a microreactor by double imaging photoelectron photoion coincidence spectroscopy (i2PEPICO) between 325 and 1273 K. The reactor flow field was characterized by CFD. Quantum chemical calculations were used for the assignment of certain species. The dissociative ionization of the room temperature precursor molecule starts at a photon energy of 8.5 eV by the rupture of the bond to an acetylacetonate ligand leading to the formation of the Al(C5H7O2)2+ ion. In pyrolysis experiments, up to 49 species were detected and identified in the gas-phase, including reactive intermediates and isomeric/isobaric hydrocarbons, oxygenated species as well as aluminium containing molecules. We detected aluminium bis(diketo)acetylacetonate-H, Al(C5H7O2)C5H6O2, at m/z 224 together with acetylacetone (C5H8O2) as the major initial products formed at temperatures above 600 K. A second decomposition channel affords Al(OH)2(C5H7O2) along with the formation of a substituted pentalene ring species (C10H12O2) as assigned by Franck-Condon simulations and quantum chemical calculations. Acetylallene (C5H6O), acetone (C3H6O) and ketene (C2H2O) were major secondary decomposition products, formed upon decomposition of the primary products. Three gas-phase aromatic hydrocarbons were also detected and partially assigned for the first time: m/z 210, m/z 186 (C14H18 or C12H10O2) and m/z 146 (C11H14 or C9H6O2) and their formation mechanism is discussed. Finally, Arrhenius parameters are presented on the gas-phase decomposition kinetics of Al(C5H7O2)3, aided by numerical simulation of the flow field.

Combustion in the future: The importance of chemistry

Combustion involves chemical reactions that are often highly exothermic. Combustion systems utilize the energy of chemical compounds released during this reactive process for transportation, to generate electric power, or to provide heat for various applications. Chemistry and combustion are interlinked in several ways. The outcome of a combustion process in terms of its energy and material balance, regarding the delivery of useful work as well as the generation of harmful emissions, depends sensitively on the molecular nature of the respective fuel. The design of efficient, low-emission combustion processes in compliance with air quality and climate goals suggests a closer inspection of the molecular properties and reactions of conventional, bio-derived, and synthetic fuels. Information about flammability, reaction intensity, and potentially hazardous combustion by-products is important also for safety considerations. Moreover, some of the compounds that serve as fuels can assume important roles in chemical energy storage and conversion. Combustion processes can furthermore be used to synthesize materials with attractive properties. A systematic understanding of the combustion behavior thus demands chemical knowledge. Desirable information includes properties of the thermodynamic states before and after the combustion reactions and relevant details about the dynamic processes that occur during the reactive transformations from the fuel and oxidizer to the products under the given boundary conditions. Combustion systems can be described, tailored, and improved by taking chemical knowledge into account. Combining theory, experiment, model development, simulation, and a systematic analysis of uncertainties enables qualitative or even quantitative predictions for many combustion situations of practical relevance. This article can highlight only a few of the numerous investigations on chemical processes for combustion and combustion-related science and applications, with a main focus on gas-phase reaction systems. It attempts to provide a snapshot of recent progress and a guide to exciting opportunities that drive such research beyond fossil combustion.

The Underlying Chemistry to the Formation of PO2 Radicals from Organophosphorus Compounds: A Missing Puzzle Piece in Flame Chemistry

Reactive species, such as ^. PO₂ and HOPO, are considered of upmost importance in flame inhibition and catalytic combustion processes of fuels. However, the underlying chemistry of their formation remains speculative due to the unavailability of suitable analytical techniques that can be used to identify the transient species which lead to their formation. This study elucidates the reaction mechanisms of the formation of phosphoryl species from dimethyl methyl phosphonate (DMMP) and dimethyl methyl phosphoramidate (DMPR) under well-defined oxidative conditions. Photoelectron photoion coincidence techniques that utilized vacuum ultraviolet synchrotron radiation were applied to isomer-selectively detect the elusive key intermediates and stable products. With the help of in situ recorded spectral fingerprints, different transient species, such as PO₂ and triplet O radicals, have been exclusively identified from their isomeric components, which has helped to piece together the formation mechanisms of phosphoryl species under various conditions. It was found that ^. PO₂ formation required oxidative conditions above 1070 K. The combined presence of O₂ and H₂ led to significant changes in the decomposition chemistry of both model phosphorus compounds, leading to the formation of ^. PO₂ . The reaction ^. PO+O₂ →^. PO₂ +O: was identified as the key step in the formation of ^. PO₂ . Interestingly, the presence of O₂ in DMPR thermolysis suppresses the formation of PN-containing species. In a previous study, PN species were identified as the major species formed during the pyrolysis of DMPR. Thus, the findings of this study has shed light onto the decomposition pathways of organophosphorus compounds, which are beneficial for their fuel additive and fire suppressant applications.

Isomer-Selective Threshold Photoelectron Spectra of Phenylnitrene and Its Thermal Rearrangement Products

The photoionization of phenylnitrene was investigated by photoion mass-selected threshold photoelectron spectroscopy in the gas phase. Flash vacuum pyrolysis of phenyl azide at 480 °C produces the nitrene, which subsequently rearranges at higher temperatures affording three isomeric cyanocyclopentadienes, in contrast to low-temperature trapping experiments. Temperature control of the reactor and threshold photoelectron spectra allows for optimizing the generation of phenylnitrene or its thermal rearrangement products, as well as obtaining vibrational information for the corresponding ions. The adiabatic ionization energies (AIE) of the triplet nitrene (³A₂) to the radical cation in its lowest-energy doublet (²B₂) and quartet (⁴A₁) spin states were determined to 8.29 ± 0.01 and 9.73 ± 0.01 eV, respectively. Vibrational frequencies of ring breathing modes were measured at 500 ± 80 and 484 ± 80 cm^-1 for both the [Formula: see text](²B₂) and [Formula: see text](⁴A₁) cationic states, respectively. The AIE differ from the values previously reported; hence, we revise the doublet-quartet energy splitting of the phenylnitrene radical cation to 1.44 eV, in excellent agreement with composite methods and coupled cluster calculations, but considerably higher than the literature reference (1.1 eV).

A pressurized flow reactor combustion experiment interfaced with synchrotron double imaging photoelectron photoion coincidence spectroscopy

A new pressurized low-temperature combustion experiment has been commissioned at the Swiss Light Source, Paul Scherrer Institute. The experiment uses photoionization with tunable synchrotron radiation and double imaging photoelectron photoion coincidence (i²PEPICO) detection at the vacuum ultraviolet beamline. The experimental setup is described, including the high-pressure reactor experiment, sampling interface, and reactant delivery system. The CRF-PEPICO (Combustion Reactions Followed by Photoelectron Photoion Coincidence) endstation and VUV beamline are briefly elaborated. The novel aspects of the apparatus and the new components are elucidated in detail, such as the fluid supply system to the reactor and the reactor integration into the endstation. We also present a system overview of the experimental setup. The technical details are followed by a description of the experimental procedure used to operate the pressurized flow reactor setup. Finally, first experimental results demonstrating the capability of the setup are provided and analyzed. A major advantage of this new experiment is that the excellent isomer resolution capabilities of the i²PEPICO technique can be transferred to the investigation of reactions at elevated pressures of several bars. This enables the investigation of pressure effects on the reactivity of fuel mixtures and covers more realistic conditions found in technical combustors. The capability to obtain quantitative oxidation data is confirmed, and the main and certain intermediate species are quantified for a selected condition. The results show excellent agreement with a chemical kinetics model and previously published reference measurements performed with a gas chromatography setup.

Photoelectron spectroscopy of boron-containing reactive intermediates using synchrotron radiation: BH2, BH, and BF

Mass selected slow photoelectron spectra (SPES) of three boron-containing reactive species, BH₂, BH, and BF were recorded by double imaging photoion-photoelectron coincidence spectroscopy (i²PEPICO) using synchrotron radiation. All species were generated in a flow reactor from the H-abstraction of B₂H₆ by F atoms created in a F₂ microwave discharge. The spectrum of BH₂⁺ exhibits a long bending mode progression with a 970 cm^-1 spacing due to the large geometry change from bent to linear upon ionization. Its ionization energy was determined as 8.12 ± 0.02 eV. For BH, photoionisation from both X¹Σ⁺ singlet and a³Π triplet state was observed, permitting the experimental determination of the singlet/triplet gap (ΔE_ST) from the observed IE's of 9.82 eV and 8.48 eV. In addition, a threshold photoelectron spectrum of BF was recorded, which leads to an IE of 11.11 eV and an improved value for ν_BF⁺ of 1690 cm^-1. All spectra were simulated by calculating Franck-Condon factors from optimised structures based on quantum chemical calculations.

Isomer-sensitive characterization of low temperature oxidation reaction products by coupling a jet-stirred reactor to an electron/ion coincidence spectrometer: case of n-pentane

Using a tunable vacuum ultraviolet synchrotron beam line and first principle computations, a jet-stirred reactor was coupled for the first time to a photoionization mass spectrometer using electron/ion coincidence imaging.

Selective identification of cyclopentaring-fused PAHs and side-substituted PAHs in a low pressure premixed sooting flame by photoelectron photoion coincidence spectroscopy

Selective on-line identification of polycyclic aromatic hydrocarbons (PAHs) formed in a low-pressure methane sooting flame, carried out using the double imaging Photoelectron Photoion Coincidence Spectroscopy method (i²PEPICO).

New analytical tools for advanced mechanistic studies in catalysis: photoionization and photoelectron photoion coincidence spectroscopy

How can we detect reactive and elusive intermediates in catalysis to unveil reaction mechanisms? In this mini review, we discuss novel photoionization tools to support this quest.

Decomposition of Picolyl Radicals at High Temperature: A Mass Selective Threshold Photoelectron Spectroscopy Study

The reaction products of the picolyl radicals at high temperature were characterized by mass-selective threshold photoelectron spectroscopy in the gas phase. Aminomethylpyridines were pyrolyzed to initially produce picolyl radicals (m/z=92). At higher temperatures further thermal reaction products are generated in the pyrolysis reactor. All compounds were identified by mass-selected threshold photoelectron spectroscopy and several hitherto unexplored reactive molecules were characterized. The mechanism for several dissociation pathways was outlined in computations. The spectrum of m/z=91, resulting from hydrogen loss of picolyl, shows four isomers, two ethynyl pyrroles with adiabatic ionization energies (IEad ) of 7.99 eV (2-ethynyl-1H-pyrrole) and 8.12 eV (3-ethynyl-1H-pyrrole), and two cyclopentadiene carbonitriles with IE's of 9.14 eV (cyclopenta-1,3-diene-1-carbonitrile) and 9.25 eV (cyclopenta-1,4-diene-1-carbonitrile). A second consecutive hydrogen loss forms the cyanocyclopentadienyl radical with IE's of 9.07 eV (T0 ) and 9.21 eV (S1 ). This compound dissociates further to acetylene and the cyanopropynyl radical (IE=9.35 eV). Furthermore, the cyclopentadienyl radical, penta-1,3-diyne, cyclopentadiene and propargyl were identified in the spectra. Computations indicate that dissociation of picolyl proceeds initially via a resonance-stabilized seven-membered ring.

Tabletop extreme ultraviolet time-of-flight spectrometry for trace analysis of high ionization energy samples

RATIONALE

Species with ionization energies beyond what is accessible using state-of-the-art lab sources are affected by poor detection limits in ordinary mass spectrometry setups, whose throughput is also often limited. Extreme ultraviolet (XUV) photoionization mass spectrometry, in combination with linear time-of-flight (TOF), is necessary for the sensitive detection of high ionization energy compounds at trace level. XUV photoionization is available at beamlines, although with limited access. A tabletop setup may fill such a gap.

METHODS

A self-developed tabletop system, based on a plasma discharge with extreme ultraviolet emission (λ = 5-50 nm) coupled to a TOF mass spectrometer, was used in this study. Simultaneous validation measurements with a reference electron ionization quadrupole mass filter were carried out. An in-house developed hollow toroidal coil (HTC) induction detector was used for concomitant photoelectron detection.

RESULTS

Straightforward XUV mass spectra without fragmentation, thanks to the single-photon ionization, were acquired. The measurements with the reference quadrupole were in agreement with the spectra acquired by XUV-TOF. The resolution obtained for N₂ was at least factor of 2 higher than that measured with the reference quadrupole. Initial energy distributions of photoelectrons were retrieved by cross-correlation that gave access to the photoionization distribution.

CONCLUSIONS

The system allows XUV single-photon ionization of elements and molecules with IE >10 eV that are of fundamental interest e.g. for water splitting and catalysis research. The demonstrated performance is now suitable for a prototype platform.

Pentadiynylidene and Its Methyl-Substituted Derivates: Threshold Photoelectron Spectroscopy of R1-C5-R2 Triplet Carbon Chains

Mass-selective threshold photoelectron spectroscopy in the gas phase was employed to characterize the dialkynyl triplet carbenes pentadiynylidene (HC₅H), methylpentadiynylidene (MeC₅H), and dimethylpentadiynylidene (MeC₅Me). Diazo compounds were employed as precursors to generate the carbenes by flash pyrolysis. The R₁-C₅-R₂ carbon chains were photoionized by vacuum ultraviolet (VUV) synchrotron radiation in photoelectron photoion coincidence (PEPICO) experiments. High-level ab initio computations were carried out to support the interpretation of the experiments. For the unsubstituted pentadiynylidene (R₁ = R₂ = H) the recorded spectrum yields an adiabatic ionization energy (IE_ad) of 8.36 ± 0.03 eV. In addition, a second carbene isomer, 3-(didehydrovinylidene)cyclopropene, with a singlet electronic ground state, was identified in the spectrum based on the IE_ad of 8.60 ± 0.03 eV and Franck-Condon simulations. We found that multireference computations are required to reliably calculate the IE_ad for this molecule. CASPT2 computations predicted an IE_ad = 8.55 eV, while coupled-cluster computations significantly overestimate the IE. The cyclic isomer is most likely formed from another isomer of the precursor present in the sample. Stepwise methyl-substitution of the carbene leads to a reduction of the IE to 7.77 ± 0.04 eV for methylpentadiynylidene and 7.27 ± 0.06 eV for dimethylpentadiynylidene. The photoionization and dissociative photoionization of the precursors is investigated as well.

Product detection study of the gas-phase oxidation of methylphenyl radicals using synchrotron photoionisation mass spectrometry

Reactions of ortho and meta-methylphenyl radicals with oxygen form products that depend acutely on the position of the methyl group.

Photoionization studies of reactive intermediates using synchrotron radiation

Photoionization with synchrotron radiation enables sensitive and selective monitoring of reactive intermediates in environments such as flames and plasmas.

Metamorphic meta isomer: carbon dioxide and ketenes are formed via retro-Diels–Alder reactions in the decomposition of meta-benzenediol

Deoxygenation of the lignin model compound resorcinol was investigated using VUV synchrotron radiation: Formation of two reactive ketenes and decarboxylation are the dominating pathways, much different from the other two benzenediol isomers.

Diborene: Generation and Photoelectron Spectroscopy of an Inorganic Biradical

Diborenes, R-BB-R', are of current interest in inorganic chemistry because they offer the opportunity to tune the properties of a biradical by modifying the substituents of the diborene parent, HBBH. Here we synthesize the elusive diborene by H atom abstraction from diborane, B₂H₆, using fluorine atoms and report a vibrationally resolved photoelectron spectrum of the HBBH biradical. The spectrum is interpreted by comparison with high-level ab initio computations, taking into account the Renner-Teller splitting in the X^+ 2Π ionic ground state, which show an excellent agreement with the experimental spectrum. An adiabatic ionization energy of 9.080 ± 0.015 eV was determined, and a vibrational progression in the boron-boron stretching vibration of 0.14 eV is visible. This is due to the reduction of bond order upon ionization, accompanied by an increase of the computed boron-boron bond length, R_BB, from 1.514 to 1.606 Å.

Radical Thermometers, Thermochemistry, and Photoelectron Spectra: A Photoelectron Photoion Coincidence Spectroscopy Study of the Methyl Peroxy Radical

We investigated the simplest alkylperoxy radical, CH₃OO, formed by reacting photolytically generated CH₃ radicals with O₂, using the new combustion reactions followed by photoelectron photoion coincidence (CRF-PEPICO) apparatus at the Swiss Light Source. Modeling the experimental photoion mass-selected threshold photoelectron spectrum using Franck-Condon simulations including transitions to triplet and singlet cationic states yielded the adiabatic ionization energy of 10.265 ± 0.025 eV. Dissociative photoionization of CH₃OO generates the CH₃⁺ fragment ion at the appearance energy of 11.164 ± 0.010 eV. Combining these two values with Δ_fH_0K^°(CH₃) yields Δ_fH_0K^°(CH₃OO) = 22.06 ± 0.97 kJ mol^-1, reducing the uncertainty of the previously determined value by a factor of 5. Statistical simulation of the CH₃OO breakdown diagram provides a molecular thermometer of the free radical's internal temperature, which we measured to be 330 ± 30 K.

Valence shell threshold photoelectron spectroscopy of C3Hx (x = 0–3)

We present the photoelectron spectra of C₃H_x (x = 0–3) formed in a microwave discharge flow-tube reactor by consecutive H abstractions from C₃H₄ (C₃H_x + F → C₃H_x−1 + HF (x = 1–4)), but also from F + CH₄ schemes by secondary reactions.

Isomer Identification in Flames with Double-Imaging Photoelectron/Photoion Coincidence Spectroscopy (i 2 PEPICO) using Measured and Calculated Reference Photoelectron Spectra

Double-imaging photoelectron/photoion coincidence (i2PEPICO) spectroscopy using a multiplexing, time-efficient, fixed-photon-energy approach offers important opportunities of gas-phase analysis. Building on successful applications in combustion systems that have demonstrated the discriminative power of this technique, we attempt here to push the limits of its application further to more chemically complex combustion examples. The present investigation is devoted to identifying and potentially quantifying compounds featuring five heavy atoms in laminar, premixed low-pressure flames of hydrocarbon and oxygenated fuels and their mixtures. In these combustion examples from flames of cyclopentene, iso-pentane, iso-pentane blended with dimethyl ether (DME), and diethyl ether (DEE), we focus on the unambiguous assignment and quantitative detection of species with the sum formulae C5H6, C5H7, C5H8, C5H10, and C4H8O in the respective isomer mixtures, attempting to provide answers to specific chemical questions for each of these examples. To analyze the obtained i2PEPICO results from these combustion situations, photoelectron spectra (PES) from pure reference compounds, including several examples previously unavailable in the literature, were recorded with the same experimental setup as used in the flame measurements. In addition, PES of two species where reference spectra have not been obtained, namely 2-methyl-1-butene (C5H10) and the 2-cyclopentenyl radical (C5H7), were calculated on the basis of high-level ab initio calculations and Franck-Condon (FC) simulations. These reference measurements and quantum chemical calculations support the early fuel decomposition scheme in the cyclopentene flame towards 2-cyclopentenyl as the dominant fuel radical as well as the prevalence of branched intermediates in the early fuel destruction reactions in the iso-pentane flame, with only minor influences from DME addition. Furthermore, the presence of ethyl vinyl ether (EVE) in DEE flames that was predicted by a recent DEE combustion mechanism could be confirmed unambiguously. While combustion measurements using i2PEPICO can be readily obtained in isomer-rich situations, we wish to highlight the crucial need for high-quality reference information to assign and evaluate the obtained spectra.

An imaging photoelectron-photoion coincidence investigation of homochiral 2R,3R-butanediol clusters

We report an experimental investigation of homochiral cluster formation in seeded molecular beam expansions of (2R,3R)-butanediol. Synchrotron radiation vacuum ultraviolet photoionization measurements have been performed using a double imaging electron-ion spectrometer in various configurations and modes of operation. These include measurements of the cluster ion mass spectra, wavelength scanned ion yields, and threshold electron spectra. Protonated cluster ions ranging up to n = 7 have been observed and size-selected photoelectron spectra and photoelectron circular dichroism (PECD) have been recorded by velocity map imaging, recorded in coincidence with ions, at a number of fixed photon energies. Translation temperatures of the cluster ions have been further examined by ion imaging measurements. As well as the sequence of protonated clusters with integral numbers of butanediol monomer units, a second series with half-integral monomer masses is observed and deduced to result from a facile cleavage of a butanediol monomer moiety within the nascent cluster. This second sequence of half-integral masses displays quite distinct behaviours. PECD measurements are used to show that the half-integral mass cluster ions do not share a common parentage with whole integer masses. Using an analogy developed with simple theoretical calculations of butanediol dimer structures, it is inferred that the dissociative branching into integral and half-integral ion mass sequences is controlled by the presence of different butanediol monomer conformations within the hydrogen bonded clusters.

Understanding the mechanism of catalytic fast pyrolysis by unveiling reactive intermediates in heterogeneous catalysis

Catalytic fast pyrolysis is a promising way to convert lignin into fine chemicals and fuels, but current approaches lack selectivity and yield unsatisfactory conversion. Understanding the pyrolysis reaction mechanism at the molecular level may help to make this sustainable process more economic. Reactive intermediates are responsible for product branching and hold the key to unveiling these mechanisms, but are notoriously difficult to detect isomer-selectively. Here, we investigate the catalytic pyrolysis of guaiacol, a lignin model compound, using photoelectron photoion coincidence spectroscopy with synchrotron radiation, which allows for isomer-selective detection of reactive intermediates. In combination with ambient pressure pyrolysis, we identify fulvenone as the central reactive intermediate, generated by catalytic demethylation to catechol and subsequent dehydration. The fulvenone ketene is responsible for the phenol formation. This technique may open unique opportunities for isomer-resolved probing in catalysis, and holds the potential for achieving a mechanistic understanding of complex, real-life catalytic processes.

The conversion of lignin by catalytic fast pyrolysis into useful fine chemicals is a promising route to fuel production, however selectivity and conversion are still not optimal. Here, the authors investigate the reaction mechanism by detection of reactive intermediates responsible for the formation of key products.

Pyrolysis of n-butane investigated using synchrotron threshold photoelectron photoion coincidence spectroscopy

Synchrotron TPEPICO and a flash pyrolysis micro-reactor were utilized to investigate thermal decomposition of n-butane and its reaction mechanisms were revealed.

Advances in threshold photoelectron spectroscopy (TPES) and threshold photoelectron photoion coincidence (TPEPICO)

The history and evolution of molecular threshold photoelectron spectroscopy and threshold photoelectron photoion coincidence spectroscopy (TPEPICO) over the last fifty years are reviewed.

Microwave spectroscopic detection of flame-sampled combustion intermediates

Microwave spectroscopy was used to detect and identify combustion intermediates after sampling out of laboratory-scale model flames.

The vacuum ultraviolet beamline/endstations at NSRL dedicated to combustion research

An undulator-based vacuum ultraviolet (VUV) beamline (BL03U), intended for combustion chemistry studies, has been constructed at the National Synchrotron Radiation Laboratory (NSRL) in Hefei, China. The beamline is connected to the newly upgraded Hefei Light Source (HLS II), and could deliver photons in the 5-21 eV range, with a photon flux of 10(13) photons s(-1) at 10 eV when the beam current is 300 mA. The monochromator of the beamline is equipped with two gratings (200 lines mm(-1) and 400 lines mm(-1)) and its resolving power is 3900 at 7.3 eV for the 200 lines mm(-1) grating and 4200 at 14.6 eV for the 400 lines mm(-1) grating. The beamline serves three endstations which are designed for respective studies of premixed flame, fuel pyrolysis in flow reactor, and oxidation in jet-stirred reactor. Each endstation contains a reactor chamber, an ionization chamber where the molecular beam intersects with the VUV light, and a home-made reflectron time-of-flight mass spectrometer. The performance of the beamline and endstations with some preliminary results is presented here. The ability to detect reactive intermediates (e.g. H, O, OH and hydroperoxides) is advantageous in combustion chemistry research.

Determination of accurate electron chiral asymmetries in fenchone and camphor in the VUV range: sensitivity to isomerism and enantiomeric purity

Photoelectron circular dichroism is a chiroptical effect able to distinguish isomers and to determine accurately the enantiopurity of chiral compounds.

Insights into gas-phase reaction mechanisms of small carbon radicals using isomer-resolved product detection

Gas-phase radical reactions of CN and CH with small hydrocarbons are overviewed with emphasis on isomer-resolved product detection.